Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interac...Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.展开更多
The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser ...The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser damage resistance of optics. In this study, the experimental study combined with numerical simulation is utilized to investigate the effect of the secondary treatment on a mitigated site by CO2laser irradiation. The results indicate that the ablation debris and the raised rim can be completely eliminated and the depth of crater can be reduced. Notable results show that the residual stress of the mitigation site after treatment will reduce two-thirds of the original stress. Finally, the elimination and the controlling mechanism of secondary treatment on the debris and raised rim, as well as the reasons for changing the profile and stress are analyzed. The results can provide a reference for the optimization treatment of mitigation sites by CO2laser secondary treatment.展开更多
In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unit...In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unity at 1180 - 900cm-1 range because of the existence of anomalous dispersion. The optical losses of hollow waveguides were calculated,the predicted losses at 940cm-1are 0. 65 and 0. 081B/ m as the inner diameter of fiber is 0. 5 and 1. 0mm respectively. The glasses can be used as the cladding materials of hol-low waveguides for transmitting CO2 laser from the measurements of characteristic temperatures, coefficient of expansion and chemical durability.展开更多
High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of r...High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.展开更多
基金National Key Basic Research Special Foundation of China
文摘Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.
基金supported by the National Natural Science Foundation of China(Grant Nos.61505170,61505171,and 51535003)the Joint Fund of the National Natural Science Foundation of China+1 种基金the Chinese Academy of Engineering Physics(Grant No.U1530109)the China Postdoctoral Science Foundation(Grant No.2016M592709)
文摘The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser damage resistance of optics. In this study, the experimental study combined with numerical simulation is utilized to investigate the effect of the secondary treatment on a mitigated site by CO2laser irradiation. The results indicate that the ablation debris and the raised rim can be completely eliminated and the depth of crater can be reduced. Notable results show that the residual stress of the mitigation site after treatment will reduce two-thirds of the original stress. Finally, the elimination and the controlling mechanism of secondary treatment on the debris and raised rim, as well as the reasons for changing the profile and stress are analyzed. The results can provide a reference for the optimization treatment of mitigation sites by CO2laser secondary treatment.
文摘In this paper a new kind of mid - infrared fiber material is reported. The reflective coefficients (R) of glasses in the system Na2O - ZnO - GeO2-SiO2-PbO have been measured-the refractive index becomes less than unity at 1180 - 900cm-1 range because of the existence of anomalous dispersion. The optical losses of hollow waveguides were calculated,the predicted losses at 940cm-1are 0. 65 and 0. 081B/ m as the inner diameter of fiber is 0. 5 and 1. 0mm respectively. The glasses can be used as the cladding materials of hol-low waveguides for transmitting CO2 laser from the measurements of characteristic temperatures, coefficient of expansion and chemical durability.
基金supported by the Joint Scientific and Technological Innovation Project of Hainan Province(2021CXLH0001)the Teaching Reform in Higher Education of Heilongjiang Province(SJGY20210135)+4 种基金the Key Subject of Education Planning in Heilongjiang Province(GJB1423352)the Guiding Innovation Fund Project of Northeast Petroleum University(2022YDL-06 and 2021YDL-13)Daqing City Guiding Science and Technology Project(zd-2021-41)the Scientific Research Start-Up Fund Project of Northeast Petroleum University(2021KQ09 and 2019KQ67)the National Key R&D Program of China(2017YFD0601004).
文摘High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.
