The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified ch...The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified che-mical component of the laser-cut surface,and the strength and adhesive penetration near the bondline.Beech-wood is cut by the laser with varying processing parameters,cutting speeds,gas pressures,and focal point positions.The laser-cut samples were divided into two groups,sanded and non-sanded samples.Polyvinyl acetate adhesive(PVAc)was used to bond the groups of laser-cut samples.After assembly with cold pressing,the tensile shear test was carried out.Numerical modelling was carried out to determine the partial elongation and shear strain of the glue line.Based on this,the shear modulus and linear elasticity of the glue line were estimated.Scan-ning electron microscopy was used to assess the adhesive penetration into the porosity structure of the laser-cut samples,and the depth of the heat-affected zone.The laser-cut surface was analysed by Fourier transform infrared spectroscopy.The wetting properties of the laser-cut surface were investigated by using a contact angle goni-ometer.The numerical model of the strain-stress curve confirmed the experimental model.The highest modulus of the linear elasticity of the glue in the numerical calculation belongs to the joint containing laser-cut samples at a gas pressure of 21(bar).The penetration depth of PVAc adhesive into the porosity structure of the laser-cut sam-ples was similar to that of sawn samples.The deepest heat-affected zone in the laser-cut samples was 150µm.A PVAc drop disappeared immediately on the laser-cut surface without sanding,but gradually on the sanded surface.In contrast,the drop on the sawn surface remained with an angle of 32°–48°.The degradation of hemi-cellulose and lignin was proven by the lower intensity of the C=O and C-O Bonds,compared to the sawn surface.展开更多
The dynamics of negative surface discharges in c-C_(4)F_(8)/CF_(3)I/CO_(2) gas mixture is investigated here with a 2D fuid model.The distributions of ion concentration,electric field strength and photon flux during th...The dynamics of negative surface discharges in c-C_(4)F_(8)/CF_(3)I/CO_(2) gas mixture is investigated here with a 2D fuid model.The distributions of ion concentration,electric field strength and photon flux during the propagation of the streamer are obtained by solving the drift-diffusion equations of particles and Poisson's equation,and the photon flux variation function during the propagation is also fitted.It is found that the streamer branches occur when the streamer transitions from the upper surface of the insulator to the side surface,and then when the streamer approaches the plane electrode,the photon flux will increase significantly.On this basis,the positive and negative surface discharge models are compared in terms of streamer characteristics,particle characteristics and streamer branches.It is found that the streamer has a higher electron concentration and electric field in the positive model.The streamer develops“floating”in the positive surface discharge,while it is close to the surface of the insulator in the negative model.In addition,the negative streamer branch has a wider width and develops further.展开更多
文摘The performance of engineered wood products is highly associated with proper bonding and an efficient cutting method.This paper investigates the influence of CO_(2) laser cutting on the wetting properties,the modified che-mical component of the laser-cut surface,and the strength and adhesive penetration near the bondline.Beech-wood is cut by the laser with varying processing parameters,cutting speeds,gas pressures,and focal point positions.The laser-cut samples were divided into two groups,sanded and non-sanded samples.Polyvinyl acetate adhesive(PVAc)was used to bond the groups of laser-cut samples.After assembly with cold pressing,the tensile shear test was carried out.Numerical modelling was carried out to determine the partial elongation and shear strain of the glue line.Based on this,the shear modulus and linear elasticity of the glue line were estimated.Scan-ning electron microscopy was used to assess the adhesive penetration into the porosity structure of the laser-cut samples,and the depth of the heat-affected zone.The laser-cut surface was analysed by Fourier transform infrared spectroscopy.The wetting properties of the laser-cut surface were investigated by using a contact angle goni-ometer.The numerical model of the strain-stress curve confirmed the experimental model.The highest modulus of the linear elasticity of the glue in the numerical calculation belongs to the joint containing laser-cut samples at a gas pressure of 21(bar).The penetration depth of PVAc adhesive into the porosity structure of the laser-cut sam-ples was similar to that of sawn samples.The deepest heat-affected zone in the laser-cut samples was 150µm.A PVAc drop disappeared immediately on the laser-cut surface without sanding,but gradually on the sanded surface.In contrast,the drop on the sawn surface remained with an angle of 32°–48°.The degradation of hemi-cellulose and lignin was proven by the lower intensity of the C=O and C-O Bonds,compared to the sawn surface.
基金the National Natural Science Foundation of China(No.62075045)。
文摘The dynamics of negative surface discharges in c-C_(4)F_(8)/CF_(3)I/CO_(2) gas mixture is investigated here with a 2D fuid model.The distributions of ion concentration,electric field strength and photon flux during the propagation of the streamer are obtained by solving the drift-diffusion equations of particles and Poisson's equation,and the photon flux variation function during the propagation is also fitted.It is found that the streamer branches occur when the streamer transitions from the upper surface of the insulator to the side surface,and then when the streamer approaches the plane electrode,the photon flux will increase significantly.On this basis,the positive and negative surface discharge models are compared in terms of streamer characteristics,particle characteristics and streamer branches.It is found that the streamer has a higher electron concentration and electric field in the positive model.The streamer develops“floating”in the positive surface discharge,while it is close to the surface of the insulator in the negative model.In addition,the negative streamer branch has a wider width and develops further.
