Research on the formability of tailor rolled blank （TRB） is of good practical significance and application value because of the enormous potential of TRB in the aspect of automobile lightweight. However, the forming...Research on the formability of tailor rolled blank （TRB） is of good practical significance and application value because of the enormous potential of TRB in the aspect of automobile lightweight. However, the forming of TRB is problematic because of the varying properties; especially, springback is a main challenge. The transverse bending （bending axis is perpendicular to the rolling direction） of TRB U channel was studied through simulation and experiment. The forming characteristics of TRB U channel during transverse bending were analyzed. The mechanisms of forming defects, including bending springback and thickness transition zone （TTZ） movement, were revealed. On this basis, effects of blank geometric parameters on springbaek and TTZ movement were discussed. The results indicate that springback and TTZ movement happen during transverse bending of TRB U-channel. Nonuni form stress distribution is the most fundamental reason for the occurrence of springback of TRB during transverse bending. Annealing can eliminate nonuniform stress distribution, and thus diminish springbaek of TRB, especially springback on the thinner side. Therefore, springback of the whole TRB becomes more uniform. However, annealing can increase the TTZ movement. Blank thickness and TTZ position are the main factors affecting the formability of TRB U-channel during transverse bending.展开更多
Sheet metal forming is one of the most preferred manufacturing processes in automotive and aerospace industries. However, due to increase in fuel prices and more stringent environmental regulation, these industries ar...Sheet metal forming is one of the most preferred manufacturing processes in automotive and aerospace industries. However, due to increase in fuel prices and more stringent environmental regulation, these industries are facing many challenges to meet the criteria. Due to this, many efforts in design and manufacturing were considered and presented.Those efforts were implementing lighter-weight materials like aluminum and magnesium（but they have higher elasticity as compared to steel） and implementing higher-strength steel with lower thickness. The main challenge found in both cases is springback after deformation. Springback is the elastic recovery after the part is unloaded. In this paper, the 3D channels with large length were deformed numerically and springback at different section was predicted. For this purpose, tailorwelded blank was considered. The geometric change along the long axis was also discussed. In addition, the effect of flange springback on wall springback was also analyzed. It was found that different section produced different springback and greater influence of flange springback. To validate the numerical simulation approach, the experiments on one case were performed and compared.展开更多
基金Item Sponsored by National Natural Science Foundation of China(51475086)Natural Science Foundation of Hebei Province of China(E2016501118,E2015501073)China Postdoctoral Science Foundation(2016M591404)
文摘Research on the formability of tailor rolled blank （TRB） is of good practical significance and application value because of the enormous potential of TRB in the aspect of automobile lightweight. However, the forming of TRB is problematic because of the varying properties; especially, springback is a main challenge. The transverse bending （bending axis is perpendicular to the rolling direction） of TRB U channel was studied through simulation and experiment. The forming characteristics of TRB U channel during transverse bending were analyzed. The mechanisms of forming defects, including bending springback and thickness transition zone （TTZ） movement, were revealed. On this basis, effects of blank geometric parameters on springbaek and TTZ movement were discussed. The results indicate that springback and TTZ movement happen during transverse bending of TRB U-channel. Nonuni form stress distribution is the most fundamental reason for the occurrence of springback of TRB during transverse bending. Annealing can eliminate nonuniform stress distribution, and thus diminish springbaek of TRB, especially springback on the thinner side. Therefore, springback of the whole TRB becomes more uniform. However, annealing can increase the TTZ movement. Blank thickness and TTZ position are the main factors affecting the formability of TRB U-channel during transverse bending.
文摘Sheet metal forming is one of the most preferred manufacturing processes in automotive and aerospace industries. However, due to increase in fuel prices and more stringent environmental regulation, these industries are facing many challenges to meet the criteria. Due to this, many efforts in design and manufacturing were considered and presented.Those efforts were implementing lighter-weight materials like aluminum and magnesium（but they have higher elasticity as compared to steel） and implementing higher-strength steel with lower thickness. The main challenge found in both cases is springback after deformation. Springback is the elastic recovery after the part is unloaded. In this paper, the 3D channels with large length were deformed numerically and springback at different section was predicted. For this purpose, tailorwelded blank was considered. The geometric change along the long axis was also discussed. In addition, the effect of flange springback on wall springback was also analyzed. It was found that different section produced different springback and greater influence of flange springback. To validate the numerical simulation approach, the experiments on one case were performed and compared.
