Geochemical characteristics and exploration significance of ultra-deep Sinian oil and gas from Well Tashen 5,Tarim Basin,NW China

The Well Tashen 5(TS5),drilled and completed at a vertical depth of 9017 m in the Tabei Uplift of the Tarim Basin,NW China,is the deepest well in Asia.It has been producing both oil and gas from the Sinian at a depth of 8780e8840 m,also the deepest in Asia in terms of oil discovery.In this paper,the geochemical characteristics of Sinian oil and gas from the well were investigated and compared with those of Cambrian oil and gas discovered in the same basin.The oil samples,with Pr/Ph ratio of 0.78 and a whole oil carbon isotopic value of31.6‰,have geochemical characteristics similar to those of Ordovician oils from the No.1 fault in the North Shuntuoguole area(also named Shunbei area)and the Middle Cambrian oil from wells Zhongshen 1(ZS1)and Zhongshen 5(ZS5)of Tazhong Uplift.The maturity of light hydrocarbons,diamondoids and aromatic fractions all suggest an approximate maturity of 1.5%e1.7%Ro for the samples.The(4-+3-)methyldiamantane concentration of the samples is 113.5 mg/g,indicating intense cracking with a cracking degree of about 80%,which is consistent with the high bottom hole temperature(179℃).The Sinian gas samples are dry with a dryness coefficient of 0.97.The gas is a mixture of kerogen-cracking gas and oil-cracking gas and has Ro values ranging between 1.5%and 1.7%,and methane carbon isotopic values of41.6‰.Based on the equivalent vitrinite reflectance(R_(eqv)=1.51%e1.61%)and the thermal evolution of source rocks from the Cambrian Yu'ertusi Formation of the same well,it is proposed that the Sinian oil and gas be mainly sourced from the Cambrian Yu'ertusi Formation during the Himalayan period but probably also be joined by hydrocarbon of higher maturity that migrated from other source rocks in deeper formations.The discovery of Sinian oil and gas from Well TS5 suggests that the ancient ultra-deep strata in the northern Tarim Basin have the potential for finding volatile oil or condensate reservoirs.

Geometry and formation mechanism of tension gashes and their implication on the hydrocarbon accumulation in the deep-seated strata of sedimentary basin:A case from Shunnan area of Tarim Basin

With the theoretical and technological developments related to cratonic strike-slip faults,the Shuntuoguole Low Uplift in the Tarim Basin has attracted considerable attention recently.Affected by multi-stage tectonic movements,the strike-slip faults have controlled the distribution of hydrocarbon resources owing to the special fault characteristics and fault-related structures.In contrast,the kinematics and formation mechanism of strike-slip faults in buried sedimentary basins are difficult to investigate,limiting the discussion of these faults and hydrocarbon accumulation.In this study,we identified the characteristics of massive sigmoidal tension gashes(STGs)that formed in the Shunnan area of the Tarim Basin.High-resolution three-dimensional seismic data and attribute analyses were used to investigate their geometric and kinematic characteristics.Then,the stress state of each point of the STGs was calculated using seismic curvature attributes.Finally,the formation mechanism of the STGs and their roles in controlling hydrocarbon migration and accumulation were discussed.The results suggest that:(1)the STGs developed in the Shunnan area have a wide distribution,with a tensile fault arranged in an enéchelon pattern,showing an S-shaped bending.These STGs formed in multiple stages,and differential rotation occurred along the direction of strike-slip stress during formation.(2)Near the principal displacement zone of the strike-slip faults,the stress value of the STGs was higher,gradually decreasing at both ends.The shallow layer deformation was greater than the deep layer deformation.(3)STGs are critical for connecting source rocks,migrating oil and gas,sealing horizontally,and developing efficient reservoirs.This study not only provides seismic evidence for the formation and evolution of super large STGs,but also provides certain guidance for oil and gas exploration in this area.

Evolution and Application of Sealing Ability of Gypsum Caprocks under Temperature-Pressure Coupling:An Example of the ZS5 Well in the Tazhong Area of the Tarim Basin

Gypsum caprocks'sealing ability is affected by temperature-pressure coupling.Due to the limitations of experimental conditions,there is still a lack of triaxial stress-strain experiments that simultaneously consider changes in temperature and pressure conditions,which limits the accuracy of the comprehensive evaluation of the brittle plastic evolution and sealing ability of gypsum rocks using temperature pressure coupling.Triaxial stress-strain tests were utilized to investigate the differences in the evolution of the confinement capacity of gypsum rocks under coupled temperaturepressure action and isothermal-variable pressure action on the basis of sample feasibility analysis.According to research,the gypsum rock's peak and residual strengths decrease under simultaneous increases in temperature and pressure over isothermal pressurization experimental conditions,and it becomes more ductile.This reduces the amount of time it takes for the rock to transition from brittle to plastic.When temperature is taken into account,both the brittle–plastic transformation's depth limit and the lithological transformation of gypsum rocks become shallower,and the evolution of gypsum rocks under variable temperature and pressure conditions is more complicated than that under isothermal pressurization.The sealing ability under the temperature-pressure coupling is more in line with the actual geological context when the application results of the Well#ZS5 are compared.This provides a theoretical basis for precisely determining the process of hydrocarbon accumulation and explains why the early hydrocarbon were not well preserved.

Quantitative prediction model for the depth limit of oil accumulation in the deep carbonate rocks:A case study of Lower Ordovician in Tazhong area of Tarim Basin

With continuous hydrocarbon exploration extending to deeper basins,the deepest industrial oil accumulation was discovered below 8,200 m,revealing a new exploration field.Hence,the extent to which oil exploration can be extended,and the prediction of the depth limit of oil accumulation(DLOA),are issues that have attracted significant attention in petroleum geology.Since it is difficult to characterize the evolution of the physical properties of the marine carbonate reservoir with burial depth,and the deepest drilling still cannot reach the DLOA.Hence,the DLOA cannot be predicted by directly establishing the relationship between the ratio of drilling to the dry layer and the depth.In this study,by establishing the relationships between the porosity and the depth and dry layer ratio of the carbonate reservoir,the relationships between the depth and dry layer ratio were obtained collectively.The depth corresponding to a dry layer ratio of 100%is the DLOA.Based on this,a quantitative prediction model for the DLOA was finally built.The results indicate that the porosity of the carbonate reservoir,Lower Ordovician in Tazhong area of Tarim Basin,tends to decrease with burial depth,and manifests as an overall low porosity reservoir in deep layer.The critical porosity of the DLOA was 1.8%,which is the critical geological condition corresponding to a 100%dry layer ratio encountered in the reservoir.The depth of the DLOA was 9,000 m.This study provides a new method for DLOA prediction that is beneficial for a deeper understanding of oil accumulation,and is of great importance for scientific guidance on deep oil drilling.

The Lower Cambrian Xiaoerbulake Formation in the Tarim Basin as a potential carbonate source rock

The oil and gas exploration of the Middle and Lower Cambrian in the Tarim Basin reveals widely distributed source rocks with the Yuertusi Formation being recognized as high-quality source rocks that are distributed in a rather small range.The Xiaoerbulake Formation that is right under the Yuertusi Formation has also been eyed as potential high-quality source rocks and is studied through analyses focusing on the stratigraphic development,the abundance,type,and maturity of organic matter,and the paleoproductivity of a dark-colored algae dolomite within the formation.The results show that the dolomite is rich in organic matter of mainly types Ⅰ and Ⅱ kerogens.Although reached the high mature to over-mature stage,the dolomite was deposited in an anoxic sedimentary environment featuring a high paleoproductivity level and a high organic carbon burial efficiency,quite favorable for the development of high-quality source rocks.The study provides material evidence to the Middle-Lower Cambrian subsalt source rock-reservoir-caprock combination model for the Tarim Basin.

The Middle and Lower Cambrian salt tectonics in the central Tarim Basin,China:A case study based on strike-slip fault characterization

Due to the considerable depth of the salt layers and the lack of calibration by exploratory drilling,the interpretation of the Middle and Lower Cambrian salt formations in the central Tarim Basin poses a challenge.In this paper,we apply the coupling and decoupling deformation theory in salt tectonics to analyze the No.7 fault mapped in the seismic datasets by the response characteristics of the Middle and Lower Cambrian layers.By quantifying the stratigraphic framework of the Middle and Lower Cambrian strata,we define the position of the salt layer with the seismic data.Structural decoupling is observed in the Middle and Lower Cambrian sequences in the Shuntuoguole Low Uplift,while deformation coupling is observed in these two sequences in the Shaya Uplift.

Effect of CO_(2)flooding in an oil reservoir with strong bottom-water drive in the Tahe Oilfield,Tarim Basin,Northwest China

The dissolution and diffusion of CO_(2)in oil and water and its displacement mechanism were investigated by laboratory experiment and numerical simulation for Block 9 in the Tahe oilfield,a sandstone oil reservoir with strong bottom-water drive in Tarim Basin,Northwest China.Such parameters were analyzed as solubility ratio of CO_(2)in oil,gas and water,interfacial tension,in-situ oil viscosity distribution,remaining oil saturation distribution,and oil compositions.The results show that CO_(2)flooding could control water coning and increase oil production.In the early stage of the injection process,CO_(2)expanded vertically due to gravity differentiation,and extended laterally under the action of strong bottom water in the intermediate and late stages.The CO_(2)got enriched and extended at the oil-water interface,forming a high interfacial tension zone,which inhibited the coning of bottom water to some extent.A miscible region with low interfacial tension formed at the gas injection front,which reduced the in-situ oil viscosity by about 50%.The numerical simulation results show that enhanced oil recovery(EOR)is estimated at 5.72%and the oil exchange ratio of CO_(2)is 0.17 t/t.

Application of Prediction Techniques in Carbonate Karst Reservoir in Tarim Basin

Carbonate karst reservoir is the emphases of Tarim＇s carbonate exploration. However, it is buried at a large depth, which results in Weak seismic reflection signal and low S/N ratio. In addition, the karst reservoir contains great heterogeneity, so reservoir prediction is very difficult. Through many years of research and exploration, we have established a suite of comprehensive evaluation technology for carbonate karst reservoir using geophysical characteristics and a geological concept model, including a technique for reconstructing the paleogeomorphology of buried hills based on a sequence framework, seismic description of the karst reservoir, and strain variant analysis for fracture estimation. The evaluation technology has been successfully applied in the Tabei and Tazhong areas, and commercial production of oil and gas has been achieved. We show the application of this technology in the Lunguxi area in North Tarim in this paper.

Petroleum Accumulation Associated with Volcanic Activity in the Tarim Basin —— Taking Tazhong-47 Oilfield as an Example

The discovery of the Tazhong-47 oilfield confirmed that it is realistic to explore oil and gas fields around igneous rocks in the Tarim basin. The favorable conditions for petroleum accumulation due to volcanic activity and igneous rocks formed during the activity show in two aspects. A) The contact surface of igneous rocks and the surrounding sedimentary rocks, like a vertical unconformity surface, formed the conduit of petroleum migration. Petroleum would accumulate once it encountered a trap in which the reservoir had fine porosity and permeability. B) It formed a trap barriered by igneous rocks, or changed or cut the original trap. In addition, volcanic rocks are a kind of potential reservoir, there are many such examples in the world, and oil also shows in the Permian igneous rocks in well Zhong-1 on Tazhong uplift. Petroleum accumulation associated with volcanic activity will be a new exploring field in the Tarim basin.

The Impact of the Linked Factors of Provenance,Tectonics and Climate on Potash Formation:An Example from the Potash Deposits of Lop Nur Depression in Tarim Basin,Xinjiang,Western China

Potash deposits commonly accumulate in highly restricted settings at the final stage of brine evaporation. This does not mean that potash deposits are formed simply as a result of the evaporation concentration of seawater or lake water, but rather as a coupling result of particular provenance, tectonics and climate activities. In this paper, we focus on the formative mechanism of the potash deposits of Lop Nur depression in Tarim Basin to interpret the detailed coupling mechanism among provenance, tectonics and climate. In terms of the provenance of Lop Nur Lake, the water of the Tarim River which displays ＂potassium-rich＂ characteristics play an important role. In addition, the Pliocene and Lower-Middle Pleistocene clastic beds surrounding Lop Nur Lake host a certain amount of soluble potassium and thus serves as ＂source beds＂ for potash formation. During the late Pliocene, the Lop Nur region has declined and evolved into a great lake from the previous piedmont and diluvial fan area. Since the mid Pleistocene, the great-united Lop Nur Lake has been separated and has generated a chain system consisting of Taitema Lake, Big Ear Lake and Luobei Lake which has turned into the deepest sag in Lop Nur Lake. Dry climate in Lop Nur region has increased since the Pliocene, and became extreme at the late Pleistocene. The study implies that potash formation in Lop Nur Lake depends on the optimal combination of extreme components of provenance, tectonics and climate during a shorter-term period. The optimal patterns of three factors are generally characterized by the long-term accumulation and preliminary enrichment of potassium, the occurrence of the deepest sub-depression and the appearance of an extremely arid climate in Lop Nur region. These factors have been interacting synergistically since the forming of the saline lake and in the later stages strong ＂vapor extraction＂ caused by extremely arid climate is needed to trigger large scale mineralization of potash deposits.

Diagenesis and Its Effect on Reservoir Quality of Silurian Sandstones,Tabei Area,Tarim Basin,China

The diagenetic processes of the Tabei sandstones in the Tarim Basin include compaction, cementation （quartz overgrowths, calcite, clay minerals and a minor amount of pyrite）, and dissolution of the feldspar and calcite cement. Porosity was reduced by compaction from an assumed original 40% to about 22.1%. Cementation reduced porosity to 26.6%. The Tabei sandstones lost a little more porosity by compaction than by cementation. Quartz cementation, especially syntaxial quartz overgrowth, is a major cause of porosity-loss in many reservoirs in moderately to deeply buried sandstone. Calcite cementation played a key role in the porosity evolution of sandstones. At the early stage of burial, the early calcite cement occupied most of the pore spaces resulting in significant porosity. On the other hand, some primary porosity has been preserved due to incomplete filling or the presence of scattered patches of calcite cement. In addition to calcite, several clay minerals, including illite and chlorite occurred as pore-filling and pore-lining cements. The pore-lining chlorite may have helped in retaining the porosity by preventing the precipitation of syntaxial quartz overgrowths. Illite, which largely occurred as hair-like rims around the grains and bridges on the pore throats, caused a substantial deterioration of penetrability of the reservoir. Calcite cement dissolution was extensive and contributed significantly to the development of secondary porosity.

Petroleum Migration Direction of the Silurian Paleo-pools in the Tarim Basin, Northwest China

The results obtained in this paper indicate that carbazole-type compounds have high thermal stability and also show stability in oxidation and bio-degradation. This kind of compounds still has a high concentration and complete distribution in the analyzed dry asphalt samples, showing that they are particularly useful in studying petroleum migration of paleo-pool. During the basin＇s first-stage of oil-gas pool formation in the Silurian in Tazhong and Tabei areas of Tarim Basin （at the end of Silurian period） and the second-stage in the Awati area （in Permian）, the petroleum experienced a long-distance migration. During the formation of the Silurian paleo-pools in Tazhong Uplift at the end of Silurian, the petroleum mainly came from the lower and middle Cambrian source rocks in the Manjiaer sag. The petroleum migrated towards the southwest-south entering the Silurian reservoir beds in Tazhong first. Then, it further migrated within Silurian from northwest to southeast along the highs of the Structural Belts to the region of the Silurian pinchout boundary in Tazhong. In Tabei Uplift, during the first-stage of pool formation, the petroleum was also from the lower and middle Cambrian source rocks in the Manjiaer sag. It migrated northwest entering the Silurian reservoir beds in the Tabei Uplift firstly, and then the migration continued in the same direction within the Silurian reservoirs and finally the petroleum was trapped in higher positions. During the second-stage pool formation in the Silurian beds in the areas around Awati sag, the petroleum mainly came from the lower-middle Cambrian source rocks in the Awati sag. The petroleum migrated from the generation center to Silurian reservoirs in all directions around the sag through major paths, and the petroleum was finally trapped in higher locations.

Hydrocarbon migration and accumulation along the fault intersection zone-a case study on the reef-flat systems of the No.1 slope break zone in the Tazhong area, Tarim Basin

Understanding hydrocarbon migration and accumulation mechanisms is one of the key scientif ic problems that should be solved for effective hydrocarbon exploration in the superimposed basins developed in northwest China. The northwest striking No.1 slope break zone, which is a representative of superimposed basins in the Tarim Basin, can be divided into five parts due to the intersection of the northeast strike-slip faults. Controlled by the tectonic framework, the types and properties of reservoirs and the hydrocarbon compositions can also be divided into five parts from east to west. Anomalies of all the parameters were found on the fault intersection zone and weakened up-dip along the structural ridge away from it. Thus, it can be inferred that the intersection zone is the hydrocarbon charging position. This new conclusion differs greatly from the traditional viewpoint, which believes that the hydrocarbon migrates and accumulates along the whole plane of the No.1 slope break zone. The viewpoint is further supported by the evidence from the theory of main pathway systems, obvious improvement of the reservoir quality （2-3 orders of magnitude at the intersection zone） and the formation mechanisms of the fault intersection zone. Differential hydrocarbon migration and entrapment exists in and around the strike- slip faults. This is controlled by the internal structure of faults. It is concluded that the more complicated the fault structure is, the more significant the effects will be. If there is a deformation band, it will hinder the cross fault migration due to the common feature of two to four orders of magnitude reduction in permeability. Otherwise, hydrocarbons tend to accumulate in the up-dip structure under the control of buoyancy. Further research on the internal fault structure should be emphasized.

The Formation and Distribution of the Marine Hydrocarbon Source Rock in the Tarim Basin,NW China

There are significant differences in type and distribution between marine source rock and continental source rock. According to the iithology, the Cambrian-Ordovician source rock in the Tarim basin is divided into two types： the carbonate source rock and the mud source rock. The two sets of source rocks are developed mainly in three sets of formations, Lower-Middle Cambrian carbonate source rock and mud source rock, Lower-Middle Ordovician mud source rock and Upper Ordovician lime mud source rock. The stratigraphic and areal distributions of the source rocks are controlled by the altitude and the sedimentary facies respectively. The mud source rock is developed in slope-semi deep sea environment. The source rock developed in the slope sedimentary environment is related with the anoxic environment and the one developed in semi deep sea has a close relationship with the up-flowing sea water. The carbonate source rock is developed mainly in platform slope of highstand systems tract and it is usually intimately associated with the salt rock. The Lower-Middle Cambrian carbonate source rock is developed mainly in the Bachu, Tazhong, Tangguzibasi and Yingmaili areas. The Lower-Middle Cambrian mud source rock is mainly developed in the areas east of the line of Kunan 1-Tadong 1. The Lower-Middle Ordovician mud source rock is developed mainly in the east slope of the Manjiaer depression. The carbonate source rock of Early Ordovician is developed mainly in the platform slope of highstand systems tract, such as the south margin of Tabei, the north slope of Tazhong, the Bachu area and Keping area.

Hydrocarbon Accumulation Conditions of Ordovician Carbonate in Tarim Basin

Based on comprehensive analysis of reservoir-forming conditions, the diversity of reservoir and the difference of multistage hydrocarbon charge are the key factors for the carbonate hydrocarbon accumulation of the Ordovician in the Tarim Basin. Undergone four major deposition-tectonic cycles, the Ordovician carbonate formed a stable structural framework with huge uplifts, in which are developed reservoirs of the reef-bank type and unconformity type, and resulted in multistage hydrocarbon charge and accumulation during the Caledonian, Late Hercynian and Late Himalayan. With low matrix porosity and permeability of the Ordovician carbonate, the secondary solution pores and caverns serve as the main reservoir space. The polyphase tectonic movements formed unconformity reservoirs widely distributed around the paleo-uplifts; and the reef-bank reservoir is controlled by two kinds of sedimentary facies belts, namely the steep slope and gentle slope. The unconventional carbonate pool is characterized by extensive distribution, no obvious edge water or bottom water, complicated oil/gas/water relations and severe heterogeneity controlled by reservoirs. The low porosity and low permeability reservoir together with multi-period hydrocarbon accumulation resulted in the difference and complex of the distribution and production of oil/gas/water. The distribution of hydrocarbon is controlled by the temporal-spatial relation between revolution of source rocks and paleo-uplifts. The heterogenetic carbonate reservoir and late-stage gas charge are the main factors making the oil/ gas phase complicated. The slope areas of the paleo-uplifts formed in the Paleozoic are the main carbonate exploration directions based on comprehensive evaluation. The Ordovician of the northern slope of the Tazhong uplift, Lunnan and its periphery areas are practical exploration fields. The Yengimahalla-Hanikatam and Markit slopes are the important replacement targets for carbonate exploration. Gucheng, Tadong, the deep layers of Cambrian dolomite in the Lunnan and Tazhong-Bachu areas are favorable directions for research and risk exploration.

Accumulation and Reformation of Silurian Reservoir in the Northern Tarim Basin

Silurian sandstone in Tarim Basin has good reservoir properties and active oil and gas shows, especially thick widely-distributed bituminous sandstone. Currently, the Silurian was found containing both bitumen and conventional reservoirs, with petroleum originating from terrestrial and marine source rocks. The diversity of their distribution was the result of ＂three sources, three stages＂ accumulation and adjustment processes. ＂Three sources＂ refers to two sets of marine rocks in Cambrian and Middle-Upper Ordovician, and a set of terrestrial rock formed in Triassic in the Kuqa depression. ＂Three stages＂ represents three stages of accumulation, adjustment and reformation occurring in Late Caledonian, Late Hercynian and Late Himalayan, respectively. The study suggests that the Silurian bitumen is remnants of oil generated from Cambrian and Ordovician source rocks and accumulated in the sandstone reservoir during Late Caledonian-Early Hercynian and Late Hercynian stages, and then damaged by the subsequent two stages of tectonic uplift movements in Early Hercynian and Pre-Triassic. The authors presumed that the primary paleo-reservoirs formed during these two stages might he preserved in the Silurian in the southern deep part of the Tabei area. Except for the Yingmaili area where the Triassic terrestrial oil was from the Kuqa Depression during Late Himalayan Stage, all movable oil reservoirs originated from marine sources. They were secondary accumulations from underlying Ordovician after structure reverse during the Yanshan- Himalayan stage. Oil/gas shows mixed-source characteristics, and was mainly from Middle-Upper Ordovician. The complexity and diversity of the Silurian marine primary properties were just defined by these three stages of oil-gas charging and tectonic movements in the Tabei area.

Oil filling history of the Bashituo Oilfield in the Markit Slope,SW Tarim Basin,China

The Markit Slope is an important area for the petroleum exploration in the Tarim Basin. Elucidation of the oil filling history of discovered oilfields has great significance for recognizing the accumulation processes of the whole region. Using molecular geochemistry, fluid inclusion techniques and basin modeling, we studied the oil filling process of the Bashituo Oilfield that is located in the west of the Markit Slope. The molecular migration indexes, such as the methyldibenzothiophene ratio （4-/1-MDBT）, trimethylnaphthalene ratio （TMNr） and pyrrolic nitrogen compounds content, decrease from west to east, indicating that the charging direction and migration pathways are from west to east. Lithological analysis and homogenization temperatures of saline fluid inclusions accompanied with oil fluid inclusions suggest that two charging periods occurred in the Devonian oil reservoir. Combining the burial history and heating history of well BT4, Basinmod 1D software modeling shows the two oil filling periods are from 290 Ma to 285 Ma and from l0 Ma to 4 Ma, respectively, and later oil filling dominates. This study may be helpful to understand the accumulation process and provide useful references for oil and gas exploration in the Markit Slope.

Sedimentary Response of Different Fan Types to the Paleogene-Neogene Basin Transformation in the Kuqa Depression,Tarim Basin,Xinjiang Province

A group of alluvial fans formed in the early Paleogene represent marginal sedimentary facies at the foot of the South Tianshan Mountain, Kuqa Depression, Tarim Basin, Xinjiang province. Two types of fans occurred in the middle-late Paleogene Kumugeliemu and Suweiyi formations： one alluvial, and the other fan delta deposited in a lacustrine setting. Within the early Neogene Jidike Formation, coastal subaqueous fans developed, probably in a deeper water lacustrine setting. The three types of fans are stacked vertically in outcrop with the sequence in ascending order： bottom alluvial, middle fan-delta, and top suhaqueous. The subaqueous is a typical coarse-fan deposit occurring in the glutinite member of the Jidike Formation in some wells. Laterally, from the foreland to the lacustrine settings, the distribution pattern of sedimentary facies represents the same three fan types sequentially. The spatial distribution of these fans was controlled by the Paleogene-Neogene Basin transformation, and evolution with different types of fans developed in the Kuqa Depression in response. In the Paleogene, the Kuqa Depression was a rift basin where an alluvial fan was deposited in the foreland setting, which, by early Neogene, became a foreland basin when the lake level changed. With any rise in lake level, fan-deltas migrated from lacustrine to foreland settings, whereas when the lake level fell, fan migration was reversed. In the early Neogene, with increasing slope and rising lake level, fans progressed and covered the previous fan-delta and lacustrine mudstone. Eventually, subaqueous fans developed, forming the present spatial configuration of these three fan types.

Types of Karst-fractured and Porous Reservoirs in China's Carbonates and the Nature of the Tahe Oilfield in the Tarim Basin

Almost all the oil and gas reservoirs developed in marine sedimentary strata of China have undergone processes of multi-phase reservoir formation and later modification. The irregular reservoirs are classified into three types as the Naxi, Tahe and Renqiu ones, increasing successively in the development degree of karstificated pores and fissures and the connection degree of independent reservoirs. In these reservoirs, the unity in the fluid feature, pressure and oil-gas-water interface also increases successively from the Naxi to the Renqiu type. The main body of Ordovician reservoirs of the Tahe Oilfield in the Tarim Basin is a network pool rather than a stratified, massive, stratigraphically-unconformed or weathering-crust one. The fluid nature of oil, gas and water, the interface positions and the pressures, as well as the dynamic conditions of fluids within the reservoirs during the production are all different from those in stratified or massive oil and gas reservoirs. Carbonates in the Akekule uplift and the Tahe Oilfield are assemblages of various types of reservoirs, which have an overall oil-bearing potential and obvious uneven distribution. Testing and producing tests are the major means to evaluate this type of reservoirs and acid fracturing improvement is a key link in petroleum exploration and development.

Advances and problems in hydrocarbon exploration in the Tazhong area, Tarim Basin

Located in the middle of the Tarim Basin, Tazhong is a typical area of compound reservoirs rich in oil and gas found in the Carboniferous, Silurian and Ordovician strata. The proved, probable and possible reserves （3P reserves） in the area amount to 5×108 tons, so it is of great significance to study the advances and problems in hydrocarbon exploration in the Tazhong area. On the basis of exploration history and analysis of scientific problems, we outline eight achievements： distribution characteristics of reservoirs, stages of reservoir formation, different sources of oil and gas and their respective contributions, the effective regional caprock and reservoir-caprock combinations dominating the vertical distribution of hydrocarbon reservoirs, the control of the Tazhong Palaeo-uplift on reservoir formation and establishing geologic models, structure balance belts influencing the reconstruction and residual potential of reservoirs after accumulation, the rules and mechanisms of fractures controlling oil and gas, and the types of favorable reservoirs and their characteristics of controlling oil and gas distribution. We further point out the main problems about the oil and gas exploration in the Tazhong area and put forward some relevant proposals.