Self-assembled S-scheme In_(2.77)S_(4)/K^(+)-doped g-C_(3)N_(4)photocatalyst with selective O_(2) reduction pathway for efficient H_(2)O_(2) production using water and air

The development of an efficient artificial H_(2)O_(2) photosynthesis system is a challenging work using H_(2)O and O_(2) as starting materials.Herein,3D In_(2.77)S_(4) nanoflower precursor was in-situ deposited on K^(+)-doped g-C_(3)N_(4)(KCN)nanosheets using a solvothermal method,then In_(2.77)S_(4)/KCN(IS/KCN)het-erojunction with an intimate interface was obtained after a calcination process.The investigation shows that the photocatalytic H_(2)O_(2) production rate of 50IS/KCN can reach up to 1.36 mmol g^(-1)h^(-1)without any sacrificial reagents under visible light irradiation,which is 9.2 times and 4.1 times higher than that of KCN and In_(2.77)S_(4)/respectively.The enhanced activity of the above composite can be mainly attributed to the S-scheme charge transfer route between KCN and In_(2.77)S_(4) according to density functional theory calculations,electron paramagnetic resonance and free radical capture tests,leading to an expanded light response range and rapid charge separation at their interface,as well as preserving the active electrons and holes for H_(2)O_(2) production.Besides,the unique 3D nanostructure and surface hydrophobicity of IS/KCN facilitate the diffusion and transportation of O_(2) around the active centers,the energy barriers of O_(2) protonation and H_(2)O_(2) desorption steps are ef-fectively reduced over the composite.In addition,this system also exhibits excellent light harvesting ability and stability.This work provides a potential strategy to explore a sustainable H_(2)O_(2) photo-synthesis pathway through the design of heterojunctions with intimate interfaces and desired reac-tion thermodynamics and kinetics.

First-Principles Investigation of Charge Transfer Mechanism of B-Doped 3C-SiC Semiconductor Material

This study delves into the charge transfer mechanism of boron (B)-doped 3C-SiC through first-principles investigations. We explore the effects of B doping on the electronic properties of 3C-SiC, focusing on a 12.5% impurity concentration. Our comprehensive analysis encompasses structural properties, electronic band structures, and charge density distributions. The optimized lattice constant and band gap energy of 3C-SiC were found to be 4.373 Å and 1.36 eV respectively, which is in agreement with previous research (Bui, 2012;Muchiri et al., 2018). Our results show that B doping narrows the band gap, enhances electrical conductivity, and influences charge transfer interactions. The charge density analysis reveals substantial interactions between B dopants and surrounding carbon atoms. This work not only enhances our understanding of the material’s electronic properties, but also highlights the importance of charge density analysis for characterizing charge transfer mechanisms and their implications in the 3C-SiC semiconductors.

Three-photon-excited fluorescence of Tb^(3+)-doped CaO-Al_2O_3-SiO_2 glass by femtosecond laser irradiation

A near infrared to visible blue, green, and red upconversion luminescence in a Tb^3＋-doped CaO-Al2O3-SiO2 glass was studied, which was excited using 800 nm femtosecond laser irradiation. The upconversion luminescence was attributed to ^5D3→^7F5, ^5D3→^7F4, ^5D3→^7F3, ^5D4→^7F6, ^5D4→^7F5, ^5D4→^7F4, and ^5D4→^7F3 transitions of Tb^3＋. The relationship between upconversion luminescence intensity and the pump power indicated that a three-photon simultaneous absorption process was dominant in this upconversion luminescence. The intense red, green, and blue upconversion luminescence of Tb^3＋-doped CaO-Al2O3-SiO2 glass may be potentially useful in developing three-dimensional display applications.

Cathodoluminescent properties of Tb^(3+)-doped yttria nanocrystallites

The Tb3＋-doped Y2O3 nanopowders were synthesized using the modified Pechini method. The average size of nanocrystaUites was controlled by different sintering temperatures. The structure and morphology of obtained nanopowders were examined using the XRD and SEM analyses. The Cr：Al2O3 was mixed with Th3＋：Y2O3 powders and its normalized emission was used. to measure a relative intensity of Tb3＋：Y2O3. The mixtures were electrophoretically deposited on ITO-glass slides. The cathodoluminescence spectra of obtained layers were recorded and analysed. The discussion over an influence of average grains size on phosphor efficiency was presented.

Ethanol-driven Room-temperature Synthesis of Potential Green-emitting Phosphors： a Case Study of Tb^3＋-doped CaHPO4

A novel green nanophosphor CaHPO4：Tb3＋ was synthesized via a room-temperatureco-precipitation route driven by ethanol solvent. X-ray powder diffraction （XRD）, scanningelectron microscopy （SEM） and photoluminescence spectroscopy （PL） techniques were utilizedto characterize the structure, morphology and fluorescence performance of the obtained powders.The results demonstrated that the prepared samples were well crystallized with triclinic phaseCaHPO4 structure and particle-like morphology. Photoluminescence measurements indicated thatCaHPOa：Tb3＋ had a strong absorption peak at 370 nm and exhibited characteristic emissions withseveral sharp peaks corresponding to the transitions 5D4-7FJ （jr = 6-3） of Tb3＋. Moreover, theluminescence optimum concentration for CaHPO4：Tb3＋ was determined to be 11 mol%, whichmight be a promising green-emitting ohosohor for display applications.

Long Lasting Phosphorescence and Photo-Stimulated Long Lasting Phosphorescence in Tb^(3+)-doped Strontium Borosilicate Glasses

Long lasting phosphorescence （LLP） and photo-stimulated long lasting phosphorescence （PSLLP） were observed in Tb^3＋-doped strontium borosilicate glasses. The green phosphorescence arises fromf-f transitions of Tb^3＋ and can be observed with naked eyes in the dark for up to 10 hours after the irradiation with a UV lamp （λmax =254 nm） for 30 min at room temperature. The glass could re-emit LLP under the stimulation of a UV lamp （λmax=366 rim） for 60 seconds after the LLP disappeared. The re-emitted LLP is called PSLLP. The glass sample was characterized by the fluorescence and thermoluminescence spectra, respectively. The possible mechanism of the LLP and PSLLP was also discussed.

Synthesis and Properties of Tb^(3+)-Doped Ca_x Sr_(1- x)WO_4

Tb^(3+)-doped Ca_ x Sr_(1- x )WO_4 was prepared by solid state reaction and characterized by powder X-ray diffractometry. According to X-ray diffraction, this material belongs to tetragonal system, which is consistent with space group I4_1/a. Lattice parameters in the systems Ca_ x Sr_(1- x )WO_4 were found to vary linearly with compositions. The emission and excitation spectra were measured. The miscibility, luminescence properties of Tb^(3+)-doped Ca_ x Sr_(1- x )WO_4 and energy transfer mechanism were discussed.

Luminescent characteristics of Tm^(3+)/Tb^(3+)/Eu^(3+) tri-doped Na_(5)Y_(9)F_(32) single crystals for white emission with high thermal stability

By using an improved Bridgman method,0.3 mol%Tm^(3+)/0.6 mol%Tb^(3+)/y mol%Eu^(3+)(y=0,0.4,0.6,0.8)doped Na_(5)Y_(9)F_(32)single crystals were prepared.The x-ray diffraction,excitation spectra,emission spectra and fluorescence decay curves were used to explore the crystal structure and optical performance of the obtained samples.When excited by 362 nm light,the cool white emission was realized by Na_(5)Y_(9)F_(32)single crystal triply-doped with 0.3 mol%Tm^(3+)/0.6 mol%Tb^(3+)/0.8 mol%Eu^(3+),in which the Commission Internationale de l’Eclairage(CIE)chromaticity coordinate was(0.2995,0.3298)and the correlated color temperature(CCT)was 6586 K.The integrated normalized emission intensity of the tridoped single crystal at 448 K could keep 62%of that at 298 K.The internal quantum yield(QY)was calculated to be~15.16%by integrating spheres.These results suggested that the single crystals tri-doped with Tm^(3+),Tb^(3+)and Eu^(3+)ions have a promising potential application for white light-emitting diodes(w-LEDs).

Ce^(3+)-Tb^(3+)共掺杂黄磷炉渣微晶玻璃的发光与能量传递

以黄磷炉渣为原料,采用高温熔融法制备Ce^(3+)-Tb^(3+)共掺杂黄磷炉渣发光微晶玻璃,通过差热分析(DTA)、X射线衍射(XRD)、稳态/瞬态荧光(FLS)、CIE色度等探究不同的Tb^(3+)掺杂量对微晶玻璃析出晶相、发光性能和样品色度的影响。结果表明,Ce^(3+)和Tb^(3+)的引入,微晶玻璃主晶相为硅灰石,在310 nm波长激发下,随着Tb^(3+)掺杂量增加,位于380 nm处Ce^(3+)的特征发射峰减小,543 nm处Tb^(3+)的特征发射峰增强,证实Ce^(3+)和Tb^(3+)之间存在能量传递,能量传递效率达到24.55%。此外,通过调整Tb^(3+)掺杂量,微晶玻璃发光颜色可由蓝光调至绿光,从而实现发光颜色的可控化。

用于痕量监测Zr^(4+)、Cr_(2)O_(7)^(2-)、Fe^(3+)、HPO_(4)^(2-)和指纹识别的功能化Eu^(3+)/Tb^(3+)配位聚合物荧光探针的构筑

采用芳香族π共轭及含氮原子有机连接剂,合成同构铽、铕发光配位聚合物(CPs){[Eu(PLIA)_(1.5)(H_(2)O)_(2)]·H_(2)O}_(n)(1)和{[Tb(PLIA)_(1.5)(H_(2)O)_(2)]·H_(2)O}_(n)(2),其中H_(2)PLIA=5-((吡啶-4-基甲基)氧基)苯-1,3-二甲酸。对合成的配合物进行了结构测定、表征和荧光痕量识别实验研究。2个同构配合物具有理想的三维框架结构,π…π堆积及氢键等弱相互作用增强了其化学稳定性;表征显示配位聚合物1和2具有良好的荧光性质、结晶性、热力学稳定性及结构完整性,可作为荧光传感的材料。1和2对水溶液中的Zr^(4+)、Cr_(2)O_(7)^(2-)和Fe^(3+)、HPO_(4)^(2-)具有选择性好、灵敏度高的荧光识别能力,其检出限分别为0.139μmol·L^(-1)(1,Zr^(4+))、0.626μmol·L^(-1)(1,Cr_(2)O_(7)^(2-))、0.430μmol·L^(-1)(2,Fe^(3+))、1.36μmol·L^(-1)(2,HPO_(4)^(2-))。探究了1和2作为探针的荧光猝灭机理。更有趣的是,1和2具有指纹识别性能,其荧光指纹纹路清晰连贯,细节明显,可被清晰观察。

Preparation and photoelectric properties of Ho^(3+)-doped titanium dioxide nanowire downconversion photoanode

Ho^3＋-doped titanium dioxide（TiO2：Ho^3＋） downconversion（DC） nanowires were synthesized through a simple hydrothermal method followed by a subsequent calcination process after being immersed in Ho（NO3）3 aqueous solution. Moreover, TiO2：Ho^3＋ nanowires（HTNWs） were used as the photoanode in dye-sensitized solar cells（DSSCs） to investigate their photoelectric properties. Scanning electron microscopy（SEM） and X-ray diffraction（XRD） were used to characterize the morphology and structure of the material, respectively. The photofluorescence and ultraviolet-visible absorption spectra of HTNWs reveal a DC from the near and middle ultraviolet light to visible light which matches the strong absorbed region of the N719 dye. Compared with the pure TNW photoanode, HTNWs DC photoanodes show greater photovoltaic efficiency. The photovoltaic conversion efficiency（η） of the DSSCs with HTNWs photoanode doped with 4% Ho2O3（mass fraction） is two times that with pure TNW photoanode. This enhancement could be attributed to HTNWs which could extend the spectral response range of DSSCs to the near and middle ultraviolet region and increase the short-circuit current density（Jsc） of DSSCs, thus leading to the enhancement of photovoltaic conversion efficiency.

杂质Mn^(4+)发光中心相关的Mg_(7)Ga_(2)GeO_(12)∶Tb^(3+)多色荧光粉发光性能

高性能稀土掺杂多色荧光材料的研发是发展先进荧光防伪技术的必要基础。本文通过高温固相法制备了一系列Tb^(3+)掺杂Mg_(7)Ga_(2)GeO_(12)荧光粉,并利用X射线衍射仪(XRD)、扫描电镜(SEM)和能量色散X射线光谱(EDS)对荧光粉的物相、颗粒尺寸与微观形貌、元素分布进行了系统表征,证实制得了结晶度良好的无规则微米级纯相荧光粉。在紫外377 nm激发下,Mg_(7)Ga_(2)GeO_(12)∶Tb^(3+)样品产生高效的Tb^(3+)蓝绿光特征发射,并具有20%Tb^(3+)最佳掺杂浓度,但同时还可发射峰值位于660 nm红光,其并不对应于Tb^(3+)离子的任何辐射跃迁。经电感耦合等离子体质谱(ICP-MS)和稳态/瞬态光谱分析,以及结合文献调研,证实红光~660 nm源于Mn^(4+)^(2)Eg→^(4)A_(2g)电子跃迁发射,Mn杂质元素来自于原材料。综合Tb^(3+)离子和Mn^(4+)杂质离子荧光性能,Mg_(7)Ga_(2)GeO_(12)∶Tb^(3+)样品具有200~420 nm范围内激发波长依赖的发光可调谐特性,可实现青、绿、黄、白、红等可视化多色显示效果,有望应用于多色荧光防伪与调控技术。

Tb^(3+)、Eu^(3+)离子共掺杂的MgAl_(2)O_(4)发光性能研究

采用水热辅助固相法,以Al(NO_(3))_(3)·9H_(2)O和Mg(NO_(3))_(2)·6H_(2)O为原料,尿素为沉淀剂,制备了Tb^(3+)、Eu^(3+)共掺杂镁铝尖晶石荧光粉。用X射线衍射、扫描电子显微镜对所得产物的相结构和形貌予以表征,结合荧光激发、发射光谱和CIE色度图分析了荧光粉的光致发光性能。结果表明:在一定浓度范围内,掺杂Tb3+和Eu^(3+)离子后基质MgAl_(2)O_(4)的晶体结构并未发生改变,而当引入沉淀剂后,获得了具有良好分散性的棒状颗粒,且Tb^(3+)与Eu^(3+)间的浓度变化对样品形貌的影响甚微。在此基础上,以377 nm近紫外光作为激发光源实现了可见光区由粉至红的多色可调谐发射。

Preparation and characterization of Eu^(3+)-doped CaCO_3 phosphor by microwave synthesis

A Eu^3＋-doped CaCO3 phosphor with red emission was prepared by microwave synthesis. The scanning electron microscopy （SEM） image and laser particle size analysis show that the CaCO3：Eu^3＋ particles are needle-like in the length range of 5.0-10.0 μm. The results of X-ray diffraction （XRD） analysis, Fourier transform infrared spectroscopy （FT-IR）, and Raman spectroscopy indicate that pure aragonite CaCO3：Eu^3＋ is prepared using microwave irradiation and the Eu^3＋ ion as a luminescence center inhabits the site of Ca^2＋. The photoluminescence excitation （PLE） spectrum shows that the strong broad band at around 270 nm and weak sharp lines in 300-550 nm are assigned to the charge transfer band of Eu^3＋-O^2- and intra-configurational 4f-4f transitions of Eu^3＋, respectively. The photoluminescence （PL） spectrum implies that the red luminescence can be attributed to the transitions from the ^5D0 excited level to the ^7FJ （J = 0, 1, 2, 3, 4） levels of Eu^3＋ ions with the mainly electric dipole transition ^5D0 → ^7F2 （614 and 620 nm）, and the Eu^3＋ ions prefer to occupy the low symmetric site in the crystal lattice.

Characterization of the BaBiO_3-doped BaTiO_3 positive temperature coefficient of a resistivity ceramic using impedance spectroscopy with T_c=155℃

BaBiO3-doped BaTiO3 （BB-BT） ceramic, as a candidate for lead-free positive temperature coefficient of resistivity （PTCR） materials with a higher Curie temperature, has been synthesized in air by a conventional sintering technique. The temperature dependence of resistivity shows that the phase transition of the PTC thermistor ceramic occurs at the Curie temperature, Tc = 155℃, which is higher than that of BaTiO3 （≤ 130 ℃）. Analysis of ac impedance data using complex impedance spectroscopy gives the alternate current （AC） resistance of the PTCR ceramic. By additional use of the complex electric modulus formalism to analyse the same data, the inhomogeneous nature of the ceramic may be unveiled. The impedance spectra reveal that the grain resistance of the BB-BT sample is slightly influenced by the increase of temperature, indicating that the increase in overall resistivity is entirely due to a grain-boundary effect. Based on the dependence of the extent to which the peaks of the imaginary part of electric modulus and impedance are matched on frequency, the conduction mechanism is also discussed for a BB-BT ceramic system.

Green and red up-conversion emissions and thermometric application of Er^(3+) -doped silicate glass

The green and red up-conversion emissions centred at about 534, 549 and 663 nm of wavelength, corresponding respectively to the ^2H11/2 → ^4I15/2, ^4S3/2 → ^4I15/2 and ^4F9/2 → ^4I15/2 transitions of Er^3＋ ions, have been observed for the Er^3＋-doped silicate glass excited by a 978 nm semiconductor laser beam. Excitation power dependent behaviour of the up-conversion emission intensity indicates that a two-photon absorption up-conversion process is responsible for the green and red up-conversion emissions. The temperature dependence of the green up-conversion emissions is also studied in a temperature range of 296-673 K, which shows that Er^3＋-doped silicate glass can be used as a sensor in high-temperature measurement.

Promotional effect for SCR of NO with CO over MnO_(x)-doped Fe_(3)O_(4) nanoparticles derived from metal-organic frameworks

MnO_(x)-Fe_(3)O_(4) nanomaterials were fabricated by using the innovative scheme of pyrolyzing manganesedoped iron-based metal organic framework in inert atmosphere and exhibited extraordinary performance of NO reduction by CO(CO-SCR).Multi-technology characterizations were conducted to ascertain the properties of fabricated materials(e.g.,TGA,XRD,SEM,FT-IR,XPS,BET,H_(2)-TPR and O_(2)-TPD).Moreover,the interaction between reactants and catalysts was ascertained by in situ FT-IR.Experimental results demonstrated that Mn was an ideal promoter for iron oxides,resulting in decrease of crystallite size,improve reducibility property,enhance the mobility and the amount of lattice O^(2-) species,as well as strength the adsorption ability of active NO and CO to form multiple species(e.g.,nitrate and carbonate).The unprecedented enhancement of CO-SCR activity over Mn-Fe nanomaterials follows the Eley-Rideal(E-R)and Langmuir-Hinshelwood(L-H)reaction pathway.

Fabrication of Gd_(2)O_(3)-doped CeO_(2)thin films through DC reactive sputtering and their application in solid oxide fuel cells

Physical vapor deposition(PVD)can be used to produce high-quality Gd_(2)O_(3)-doped CeO2(GDC)films.Among various PVD methods,reactive sputtering provides unique benefits,such as high deposition rates and easy upscaling for industrial applications.GDC thin films were successfully fabricated through reactive sputtering using a Gd_(0.2)Ce_(0.8)(at%)metallic target,and their application in solid oxide fuel cells,such as buffer layers between yttria-stabilized zirconia(YSZ)/La0.6Sr0.4Co0.2Fe0.8O_(3−δ)and as sublayers in the steel/coating system,was evaluated.First,the direct current(DC)reactive-sputtering behavior of the GdCe metallic target was determined.Then,the GDC films were deposited on NiO-YSZ/YSZ half-cells to investigate the influence of oxygen flow rate on the quality of annealed GDC films.The results demonstrated that reactive sputtering can be used to prepare thin and dense GDC buffer layers without high-temperature sintering.Furthermore,the cells with a sputtered GDC buffer layer showed better electrochemical performance than those with a screen-printed GDC buffer layer.In addition,the insertion of a GDC sublayer between the SUS441 interconnects and the Mn-Co spinel coatings contributed to the reduction of the oxidation rate for SUS441 at operating temperatures,according to the area-specific resistance tests.

2 μm mid-infrared optical spectra of Tm3+-doped germanium gallate glasses

Glasses with the composition of 65GeO212Ga2O3-10BaO-8Li2O-5La2O3(molar ratio) doped with 1.526 wt.%, 3.006 wt.%, 5.836 wt.%, 11.028 wt.%, and 15.678 wt.% Tm2O3, respectively, were fabricated by conventional melting method. According to the absorption spectra and the Judd-Ofelt theory, the J-O strength parameters (Ω2,Ω4, Ω6) were calculated, with which the radiative transition probabilities,branching ratios and radiative lifetimes were obtained. The infrared emission spectra (with 808 nm LD excitation) at～1.47 and～1.8 μm of various concentrations of Tm3+-doped glasses were studied. The emission intensity at～1.8 μm reached to the maximum when the Tm2O3-doping concentration was near to be～3.006 wt.% (1.0 mol.%), and then decreased as doping concentration increased further. The mechanism of the fluorescence intensity change was explained with the cross-relaxation effect and the concentration quenching effect of Tm3+. Meanwhile, according to McCumber theory, the absorption and emission cross-sections corresponding to the 3F4→3H6 transitions of Tm3+ at 1.8 μm was obtained. For Tm3+-doped germanate glasses, the maximum emission cross-section reached a value higher than that re-ported for fluorozircoaluminate glasses. It is expected to be a favorable candidate host for～2.0 μm mid-inflated laser because the glass shows favorable optical spectra.

Tm^(3+)-doped tellurite glass with Yb^(3+) energy sensitized for broadband amplifier at 1400–1700 nm bands

A kind of novel experiment was disclosed as it possessed two bands of fluorescence emission at 1.4 and 1.6 μm, which were perfectly complimentary to the current C band of optic communication. The fluorescence was based on energy transfer and up-conversion processes between Tm^3＋ and Yb^3＋ under direct pumping of 975 nm LD. The spectra and lifetimes of Tm^3＋ fluorescence in the tellurite glass were described. The corresponding fluorescence characteristics and energy migration process were analyzed by the method of lifetime and intensity comparison. The mechanism of the up-conversion based IR fluorescence was presented upon analyzing the multi-photon pumping process. The potential advantages of Tm^3＋/Yb^3＋ co-doped tellurite glass as amplifier material were concluded.