Influences of Technological Parameters on Carbothermal Reduction and Nitridation of Titanium Dioxide

The particle size of starting materials, the homogeneity of the carbon/oxide mixtures, and the carbon content are important parameters for a rapid reaction. The influences of technological parameters（carbon particle size, oxide particle size, mixing method, carbon content） on the reaction rate of carbothermal reduction and nitridation of titanium dioxide （TiO2 ） were investigated by a continuous thermo-gravimetric analyzer for large size specimen. The carbon particle size is the most impor tant parameter for a rapid reaction, but carbon particle may have no influence on the morphology of titanium nitride （TiN） powder. Oxide particles are the precursors of TiN powder, but the TiO2 particles size has very little influence on the reaction rate. The carbon content not only influences the reaction rate to some degree, but also influences the purity of TiN powder. The mixing method of the specimen has very little influence on the reaction rate. These results are suitable for other nitrides and carbides prepared by carbothermal reduction method.

Physical and Technological Parameters of Maize Varieties (Zea mays L.) Grown in the Southern Parts of Benin and the Influence of Chemical Composition

Objective: The study aims to investigate some physical and technological parameters of varieties of maize collected from the most representative areas of maize production in the southern part of Benin, and mainly used by the populations of those areas. Method: The chemical composition, physical and technological characteristics of the grains were determined using standard methods. Results: The results showed that the weight of 1000 grains ranges from 158.01 to 305.12 g, the length from 0.79 to 1.81 cm, the average width from 0.74 to 1.51 cm, thickness from 0.36 to 0.85 cm and density from 1.07 to 1.25. Regarding the technological parameters, the hardness of the grains before and after cooking was between 16.78 and 47.20 kgf, and 0.23 and 0.71 kgf respectively, while the cooking time varies from 71.00 and 158.33 mn. There was a positive and significant correlation (r = 0.405;p < 0.026) between the hardness after cooking and the weight of 1000 grains, between the hardness after cooking and grain width (r = 0.460;p < 0.011). A positive and highly significant correlation (r = 0.527, p < 0.003) was also observed between the hardness after cooking and the grain length, between the hardness after cooking and the thickness of grain (r = 0.476, p < 0.008), and between the grain density and the weight of 1000 grains (r = 0.481, p < 0.007). A positive and highly significant correlation (r = 0.923, p < 0.000) was also observed between maize grain length and width, and between grain length and grain thickness (r = 0.764, p < 0.000) and between the width and thickness (r = 0.764, p < 0.000). On the other hand, a significant negative correlation (r = -0.394, p < 0.031) was found between the hardness before cooking and the thickness and between the hardness before cooking and sphericity index (r = -0465*, p Conclusion: Through its chemical and technological characteristics the maize constitutes an important raw material for many culinary recipes in West African region.

BP Neural Network of Continuous Casting Technological Parameters and Secondary Dendrite Arm Spacing of Spring Steel

The continuous casting technological parameters have a great influence on the secondary dendrite arm spacing of the slab, which determines the segregation behavior of materials. Therefore, the identification of technological parameters of continuous casting process directly impacts the property of slab. The relationships between continuous casting technological parameters and cooling rate of slab for spring steel were built using BP neural network model, based on which, the relevant secondary dendrite arm spacing was calculated. The simulation calculation was also carried out using the industrial data. The simulation results show that compared with that of the traditional method, the absolute error of calculation result obtained with BP neural network model reduced from 0. 015 to 0. 0005, and the relative error reduced from 6, 76 % to 0.22 %. BP neural network model had a more precise accuracy in the optimization of continuous casting technological parameters.

Investigating on casting mold (or core) making with coated sand by the selected laser sintering

Using a special coated sand as the material of the selected laser sintering (SLS), the authors test and investigate the strength change of the test samples in terms of different sintering parameters (scanning speed, laser power, sintering thickness, and so on). The characteristics of coated sand hardening by laser beam are analyzed. The sintered mold (or core) for given casting is poured with molten metal.

UNITECR 2011

Hosted by The Technical Association of Refractories, Japan, 12th Unified International Technical Conference on Refractories （UNTECR） will be held in Kyoto, Japan from Oct. 31 to Nov. 2, 2011.

Research into Technology of Bao Steel's Pickling Tension Leveler

According to the survey of Bao Steel's pickling tenstion leveler,the technology of the tension leveler is analysed systematically.In order to solve the problem which hinders the production,the given technological parameters of this leveler have been improved and good results achieved.

Numerical simulation on the process of multi-point forming for tube

To apply the multi-point forming technology to the field of tube processing,the process of multi-point forming for tube is studied.Numerical simulation for the process of multi-point forming for tube is achieved by using elastic-plastic FEM in ABAQUS.During simulation,reasonable coefficient of mass scaling and friction model of penalty function are used.The influence of several major technological parameters on the process is analyzed.When the tube diameter is 60 mm and the forming curvature radius is 1000 mm,the distortion rate of cross-section and the absolute forming error gradually decrease with the increasing of tube wall thickness;However,when the tube wall thickness is constant,the smaller the curvature radius,the larger the distortion rate of cross-section,but as to forming part,its absolute forming error becomes smaller.

The Study on Wheat Concurrent-flow Drying Technology

The relation between technology parameters and performance index of the wheat three-stage concurrent-flow drying technology is studied by use of quadratic orthogonial rotate combinative experiment design method.The optimum parameters of drying technology are obtained by nonlinear optimize corresponding regression model and test.All experiment was finished in concurrent-flow grain drying experiment table.The results of this study will be significant for designing energy-saving grain drying machine.

Numerical prediction of the incremental melting and solidification process

A mathematical formulation is applied to represent the phenomena in theincremental melting and solidification process (IMSP), and the temperature and electromagneticfields and the depth of steel liquid phase are calculated by a finite difference technique using thecontrol volume method. The result shows that the predicted values are in good agreement with theobservations. In accordance with the calculated values for different kinds of materials anddifferent size of molds, the technological parameter of the IMS process such as the power supply andthe descending speed rate can be determined.

Improving the Efficiency of Mechatronic Systems in Order to Ensure Intensive Reform“Industry-4.0”

The presented work will show the highest relevance of solving all the issues related to this problem and present the results of the analysis of the main expected potential problems,which may occur in the implementation of the INDUSTRY-4.0 reform.It is proved that the pace and level of development of this reform will be determined to a large extent by the effectiveness of the individual nodes used and the entire mechatronic system.It has also been established that as a result of systematic miniaturization of the nodes of radio-electronic equipment and microelectronic equipment and microelectronic technology,the main problem of these reforms and the implementation of complex technological processes is instrumental and technological support,especially with cutting micro-tools and equipment.Therefore,on the example of these investigations,methods for improving their performance are shown.

Investigation and Application of Non-sinusoidal Oscillation Technique of Mold

To improve the slab quality, a kind of non-sinusoidal oscillation technique of mold driven by elliptic gears was developed. The waveform functions of non-sinusoidal oscillation were determined, and the calculation method and curves of technological parameters for non-sinusoidal oscillation were given. At the case of waveform deviation factor a equal to 0.31 and oscillation amplitude h equal to ±2.7 mm, the relationship between oscillation frequency and casting speed is determined, and the technological parameters for non-sinusoidal oscillation are calculated. The testing results of industrial application indicated that this technique could not only improve the Slab surface quality, but also reduce the steel breakout.

Effect of Nb on Austenite Recrystallization in High Temperature Deformation Process

By analyzing the stepped test pieces with optical microscope,the influence of the technological parameters including rolling temperature and reduction on the austenite recrystallization fraction of steel with Nb content of 0.08% deformed at high temperature processing was studied,and the deformed austenite recrystallization figures of the test steel were obtained.The result indicates that when the reduction is 60%,the critical temperature of complete recrystallization is 1070 ℃ and the borderline temperature of non-recrystallization is 900 ℃.In contrast with general HSLA steel,the recrystallization and non-recrystallization temperatures are respectively 120 ℃ and 100 ℃ higher than those of ordinary HSLA,so the steel with high content of Nb has better hot processing performance because Nb has great function of holding back recrystallization.

Mass transfer mechanisms in fixed-bed adsorption of erythromycin

The equilibrium and kinetic characteristics of the adsorption of erythromycin to Sepabeads SP825 were determined.The equilibrium data in a batch system was well described by a Langmuir isotherm.The separation performance was investigated in a fixed-bed system with respect to the adsorption superficial velocity,ionic strength and pH.A mathematical model was used to simulate the mass transfer mechanism,taking film mass transfer,pore diffusion and axial dispersion into account.The model predictions were consistent with the experi-mental data and were consequently used to determine the mass transfer coefficients.