Temperature sensor based on a single-mode tapered optical fiber

A temperature sensor is demonstrated and fabricated by coating the single-mode tapered optical fiber with temperature-sensitive silicone rubber. It works on the change of the evanescent fields in the tapered optical fiber. Small changes in the refractive index of coating film greatly influence the power of evanescent fields, which modulate the transmission optical power in the waist region. The range of temperature measured is from -20℃ to 70 ℃. The results show that the temperature sensor has high temperature sensitivity （0.012 mW/℃） and good repeatability.

Network Integration of Distributed Optical Fiber Temperature Sensor

The integration of distributed optical fiber temperature sensor with supervisory control and data acquisition （SCADA） system is proposed and implemented. In the implementation of the integration, both the compatibility with traditional system and the characteristics of distributed optical fiber temperature sensor is considered before Modbus TCP/IP protocol is chosen. The protocol is implemented with open source component Indy. The Modbus TCP/IP protocol used in the system is proved to be fast and robust.

Flexible Optical Waveguide Bent Loss Attenuation Effects Analysis and Modeling Application to an Intrinsic Optical Fiber Temperature Sensor

The temperature dependence of the bending loss light energy in multimode optical fibers is reported and analyzed. The work described in this paper aims to extend an initial previous analysis concerning planar optical waveguides, light energy loss, to circular optical waveguides. The paper also presents à novel intrinsic fiber optic sensing device base on this study allowing to measure temperatures parameters. The simulation results are validated theoretically in the case of silica/silicone optical fiber. A comparison is done between results obtained with an optical fiber and the results obtained from the previous curved optical planar waveguide study. It is showed that the bending losses and the temperature measurement range depend on the curvature radius of an optical fiber or waveguide and the kind of the optical waveguide on which the sensing process is implemented.

Highly sensitive optical fiber temperature sensor based on resonance in sidewall of liquid-filled silica capillary tube

A highly sensitive optical fiber temperature sensor based on a section of liquid-filled silica capillary tube(SCT)between single mode fibers is proposed. Two micro-holes are drilled on two sides of SCT directly by using femtosecond laser micromachining, and liquid polymer is filled into the SCT through the micro-holes without any air bubbles and then sealed by using ultra-violet(UV) cure adhesive. The sidewall of the SCT forms a Fabry–Perot resonator, and loss peaks are achieved in the transmission spectrum of the SCT at the resonant wavelength. The resonance condition can be influenced by the refractive index variation of the liquid polymer filled in SCT, which is sensitive to temperature due to its high thermooptical coefficient(-2.98 × 10^-4℃^-1). The experimental result shows that the temperature sensitivity of the proposed fiber structure reaches 5.09 nm/℃ with a perfect linearity of 99.8%. In addition, it exhibits good repeatability and reliability in temperature sensing application.

Novel Fiber Optic Temperature Sensor with Full Compensation Based on Optical Absorption

A novel system configuration of fiber optic sensor based on optical abso rption is proposed. Several compensation measures are discussed. A simulated exp eriment is designed and the output curve of system is given. The experiment al result shows that these compensation measures are effective on dynamic distu rbances which are caused by background light and optical fiber bend. In addition , the drifts in the light source intensity, fiber losses, and photodetector effi ciency are also compensated.

A Micro S-Shaped Optical Fiber Temperature Sensor Based on Dislocation Fiber Splice

We fabricated a simple, compact, and stable temperature sensor based on an S-shaped dislocated optical fiber. The dislocation optical fiber has two splice points, and we obtained the optimal parameters based on the theory and our experiment, such as the dislocation amount and length of the dislocation optical fiber. According to the relationship between the temperature and the peak wavelength shift, the temperature of the environment can be obtained. Then, we made this fiber a micro bending as S-shape between the two dislocation points, and the S-shaped micro bending part could release stress with the change in temperature and reduce the effect of stress on the temperature measurement. This structure could solve the problem of sensor distortion caused by the cross response of temperature and stress. We measured the S-shaped dislocation fiber sensor and the dislocation fiber without S-shape under the same environment and conditions, and the S-shaped dislocation fiber had the advantages of the stable reliability and good linearity.

Temperature dependence of the refractive index of optical fibers

Many experimental investigations on the temperature dependence of the refractive index of optical fibers have been reported previously, however a satisfying theoretical explanation for it is still absent. In this paper, a theoretical model about the temperature dependence of the refractive index of optical fibers is presented and it is in agreement with the previous experimental results. This work is a significant reference for the research and development of temperature sensors based on optical fiber delay lines.

Mathematical Model of Fiber Optic Temperature Sensor Based on Optic Absorption and Experiment Testing

On the basis of analysis on the temperature monitoring methods for high voltage devices, a new type of fiber optic sensor structure with reference channel is given. And the operation principle of fiber optic sensor is analysed at large based on the absorption of semiconductor chip. The mathematical model of both devices and the whole system are also given. It is proved by the experiment that this mathematical model is reliable.

Low-noise and highly stable optical fiber temperature sensor using modified pulse-reference-based compensation technique

We modify the pulse-reference-based compensation technique and propose a low-noise and highly stable optical fiber temperature sensor based on a zinc telluride film-coated fiber tip. The system noise is measured to be 0.0005 dB, which makes it possible for the detection of the minor reflectivity change of the film at different temperatures. The temperature sensitivity is 0.0034 d B/℃, so the resolution can achieve 0.2℃. The maximum difference of the temperature output values of the sensor at 20℃ at different points in time is 0.39℃. The low cost, ultra-small size, high stability, and good repeatability of the sensor make it a promising temperature sensing device for practical application.

High-sensitivity temperature sensor based on Bragg grating in BDK-doped photosensitive polymer optical fiber

A single-mode polymer optical fiber （POF） with highly photosensitive core doped with benzil dimethyl ketal （BDK） is fabricated and used for writing Bragg grating through the two-beam interference method. The Bragg wavelength of the grating is about 1570 nm, while the full-width at half-maximum （FWHM） of the reflection peak is 0.3 nm. The temperature response of POF Bragg grating is theoretically analyzed and experimentally measured in contrast to silica optical fiber Bragg grating （FBG）. The result shows that the temperature character of POF Bragg grating is negative, which is opposite to the silica optical FBG. The absolute value of the temperature response of POF Bragg grating is one order of magnitude higher than that of the silica optical FBG, making POF Bragg grating appear to be very attractive for constructing temperature sensors with high resolution.

Review of femtosecond laser fabricated optical fiber high temperature sensors [Invited]

The femtosecond laser has been an efficient tool for optical fiber high temperature sensor construction.Here,we review the progress of optical fiber high temperature sensors based on femtosecond laser fabricated fiber gratings and various types of fiber in-line interferometers in silica fibers and sapphire fibers.

Fabry-Perot Temperature Sensor for Quasi-Distributed Measurement Utilizing OTDR

A quasi-distributed Fabry-Perot fiber optic temperature sensor array using optical time domain reflectometry （OTDR） technique is presented. The F-P sensor is made by two face to face single-mode optical fibers and their surfaces have been polished. Due to the low reflectivity of the fiber surfaces, the sensor is described as low Fresnel Fabry-Perot interferometer （FPI）. The working principle is analyzed using twobeam optical interference approximation. To measure the temperature, a certain temperature sensitive material is filled in the cavity. The slight changes of the reflective intensity which is induced by the refractive index of the material was caught by OTDR. The length of the cavity is obtained by monitoring the interference spectrum which is used for the setting of the sensor static characteristics within the quasi-linear range. Based on our design, a three point sensor array are fabricated and characterized. The experimental results show that with the temperature increasing from -30℃ to 80℃, the reflectivity increase in a good linear manner. The sensitivity was approximate 0.074 dB℃. For the low transmission loss, more sensors can be integrated.

Miniature temperature sensor based on optical microfiber

Optical microfibers （OMs） are good alternatives in the field of sensing. In this letter, a simple and effective miniature temperature sensor based on OM is proposed and experimentally verified. Using pure water and fiber coating as the OM clad, an additional loss will occur due to the absorption of outer medium. The temperature of the outer environment can be estimated by monitoring the change in additional loss. In the demonstrated experiments, a series of OM with different diameters, waist lengths, and constructions are used as sensing elements. The correlation coefficients between the experimental results and the linear fittings are better than 0.99, and the temperature sensitivity obtained by the linear fittings can achieve -0.151 dB/℃ （in pure water） and -0.405 dB/℃ （covered by fiber coating）. Moreover, higher sensitivity can be obtained by decreasing the diameter, increasing the waist length of the OM, or choosing the proper operating wavelength.

Refractive index and temperature sensing characteristics of an optical fiber sensor based on a tapered single mode fiber/polarization maintaining fiber

An evanescent field optical fiber sensor based on a short section of polarization maintaining fiber spliced with a tapered single mode fiber is proposed and experimentally investigated. We mainly focus on the refractive index （RI） and temperature sensing characteristics of this compact device. The transmission spectrum of the resonance wavelength, induced by the interference between the excited low order cladding modes and core modes, shows the quadratic function relationships with RI and linear relationships with temperature. Thus, the proposal of this simple-to-fabricate, compact, and low cost sensor shows its possible potential in the sensitive detection field.

Optical Properties of High Sensitivity Fiber Bragg Grating on Temperature Sensor

In this paper, the spectrum shift properties of the center reflection wavelength detected to be based on the FBG sensor with ambient temperature change. The basic theoretical methods and numerical simulation for the spectral properties of uniform Bragg grating is analyzed by using coupling mode theory which is optical properties of high sensitivity fiber Bragg grating on temperature sensor in accordance with experiment.

Micro-Structured Fiber Interferometer as Sensitive Temperature Sensor

We report on a fast and sensitive temperature sensor using a micro-structured or photonic crystal fiber interferometer with a high germanium doped fiber core. The wavelength sensitivity for temperature variation was as high as △λ/△T= 78 pm/℃ up to 500℃, which was 6 times more sensitive than the fiber Bragg grating temperature sensitivity of △λ/△TT= 13pm/℃ at 1550nm. The sensor device was investigated conceming the sensitivity characteristics and response time.

BN/SiBCN light-leakage-proof coatings of silica optical fiber for long term sensors at high temperatures

SiBCN and BN/SiBCN light-leakage-proof coatings were prepared on silica optical fibers for sensing applications at high temperatures.Scanning electron microscopy was used to characterize the surface morphology and microstructure of the coated fiber.Mechanical and optical properties of the coated fiber were characterized by Raman,optical and tensile tests.Compared with the original fiber,the tensile strength of Si BCN and BN/Si BCN coated fiber show an increase of about 60%and 90%at room temperature,respectively.In addition,the tensile strength of BN/Si BCN coated silica optical fiber was increased by about 42%at 700°C.It has been found that the improvement of the strength of BN/Si BCN coated silica optical fiber is related to the healing of defects and residual compressive stress in fibers.From the light transmittance performance of the coated fiber,it was found that BN/Si BCN double coating could be an ideal total reflection solution to protect silica optical fiber from light leakage during high temperature sensing operation.

A high sensitive fiber Bragg grating cryogenic temperature sensor

At cryogenic temperature, a fiber Bragg grating （FBG） temperature sensor with controllable sensitivity and variable measurement range is demonstrated by using bimetal configuration. In experiments, sensitivities of -51.2, -86.4, and -520 pm/K are achieved by varying the lengths of the metals. Measurement ranges of 293 - 290.5, 283 - 280.5, and 259 - 256.5 K are achieved by shortening the distance of the gap among the metals.

High-temperature sensor using a Fabry-Perot interferometer based on solid-core photonic crystal fiber

A micro Fabry-Perot interferometer （M-FPI） is constructed by splicing a short section of polarization- maintaining photonic crystal fiber （PM-PCF） to an end-cleaved single-mode fiber with controllable offset. Due to the high effective optical path difference induced by the solid core of the PCF, the M-FPI has an ultrasmall cavity of approximately 110 μm. The temperature sensitivity within a range from 33 ℃ to approximately 600 ℃ is measured to be 13.8 pm/℃, which shows good agreement with the theoretical result. This proposed sensor has the advantages of ultracompact size and high stability. Therefore, it is suitable for various space-limited sensing applications in harsh environments.

Effect of Temperature and Gamma-Ray Irradiation on Optical Characteristics of Fiber Bragg Grating Inscribed Radiation-Resistant Optical Fiber

A new radiation-hard germano-silicate glass optical fiber with a pure silica glass buffer and a boron-doped silica glass inner cladding was fabricated for temperature sensor application based on the fiber Bragg grating(FBG)underg-ray irradiation environment.The temperature dependences of optical attenuation at 1550.5 nm and Bragg reflection wavelength shift from 18℃to 40℃before theγ-ray irradiation were about 4.57´10^(-4)dB/℃and 5.48 pm/℃,respectively.The radiation-induced optical attenuation at 1550.5 nm and the radiation-induced Bragg reflection wavelength shift under theγ-ray irradiation with the total dose of 22.85 kGy at 35℃were about 0.03 dB/m and 0.12 nm,respectively,with theγ-ray irradiation sensitivity of 5.25´10^(-3)pm/Gy.The temperature and theγ-ray irradiation dependence of optical attenuation at 1550.5 nm in the FBG written fiber with boron-doped silica glass inner cladding were about 6 times and 4 times lower than that in the FBG written fiber without boron-doped silica glass inner cladding under a temperature change from 18℃to 40℃and theγ-ray irradiation with the total dose of 22.85 kGy at 35℃,respectively.Furthermore,the effect of temperature increase on the Bragg reflection wavelength of the FBG written fiber with boron-doped silica inner cladding was much larger about 1000 times than that of theγ-ray irradiation.However,no influence on the reflection power of the Bragg wavelengths and the full width at half maximum(FWHM)bandwidth under temperature and theγ-ray irradiation change was found.Also,after theγ-ray irradiation with the dose of 22.85 kGy,no significant change in the refractive index was found but the residual stresses developed in the fiber were slightly relaxed or retained.