Conduction Properties of highly Conductive a-Si∶H∶Y Alloy Films at Low Temperature

Conductive n type a Si∶H∶Y alloy films with the conductivity as high as 60 S/cm have been deposited on Si substrate by radio frequency sputtering. In the temperature range 20～300 K, for samples with large Y contents, the thermally activated conduction is also observed and the plots of lg σ vs. 1/ T can be fitted by two linear functions with different slopes. The corresponding temperatures of the kinks between the two straight lines depend on the Y contents in the samples. For small Y content films, the conductivities can be fitted to the funciton σ∝ exp (-1/ T 1/4 ). The present results are interpreted using different conduction mechanisms in different temperature ranges for samples with different Y contents.

Effect of Introducing Conductive Organic Carrier on Properties of Low-Temperature Conductive Silver Paste

The poly(epoxy-N-methylaniline)conductive organic carrier was used as the bonding phase of the low-temperature conductive silver paste.Then,this was mixed with different proportions of silver powder to prepare the low-temperature conductive silver paste.Afterwards,the effect of the conductive organic carrier on the properties of the low-temperature conductive silver paste was determined by IR,DMA and SEM.The results revealed that the prepared conductive paste has good conductivity,film-forming performance,printing performance,low-temperature curing performance,and anti-aging performance.When the mass percentage of the bonding phase/conductive phase was 40/60,the lowest volume resistivity of the conductive silver paste was 4.9×10^(−6)Ω⋅cm,and the conductivity was the best.

Interval finite difference method for steady-state temperature field prediction with interval parameters

A new numerical technique named interval finite difference method is proposed for the steady-state temperature field prediction with uncertainties in both physical parameters and boundary conditions. Interval variables are used to quantitatively describe the uncertain parameters with limited information. Based on different Taylor and Neumann series, two kinds of parameter perturbation methods are presented to approximately yield the ranges of the uncertain temperature field. By comparing the results with traditional Monte Carlo simulation, a numerical example is given to demonstrate the feasibility and effectiveness of the proposed method for solving steady-state heat conduction problem with uncertain-but-bounded parameters.

Concentration and Temperature Dependence of Electrical Conductivity in Thermally Stable Chromium Polyacrylate

Electrical conductivity of chromium polyacrylate with dopant concentration 30, 40 and 50 wt-% of chromium has been measured over a broad range of temperatures (303 K to 383 K).The electrical conductivity shows dependence on temperature, as well as, level of doping. The conductivity is considered to be due to thermal hopping motion of localized charge carriers,which are believed to be polarons, in the temperature range 303 K to 323 K and for T>343 K,whereas. it is metal-like in the temperature range 323 K to 343 K

Resistivity-temperature Characteristics of Conductive Asphalt Concrete

The changes of resistivity of conductive asphalt concrete at different temperatures were studied,and positive temperature coefficient（PTC）modelwas established to estimate the influence of temperature on the resistivity quantitatively,which eliminated the interference with conductivity evaluation brought by temperature variation.Finally,the analysis of temperature cycling test results proves that the changes of percolation network structure caused by temperature variation prompt the emergence of PTC of conductive asphalt concrete.

Effects of Substrate Temperature on Properties for Transparent Conducting ZnO:A1 Films on Organic Substrate Deposited by r.f. Sputtering

This paper presents the substrate temperature dependence of opto-electrical properties for transparent conducting Al-doped ZnO films prepared on polyisocyanate (PI) substrates by r f sputtering. Polycrystalline ZnO:Al films with good adherence to the substrates having a (002) preferred orientation have been obtained with resistivities in the range from 4.1×10-3to 5.3×104 Ωcm, carrier densities more than 2.6×1020 cm-3 and Hall mobilities between 5.78 and 13.11 cm2/V/s for films. The average transmittance reaches 75% in the visible spectrum. The quality of obtained films depends on substrate temperature during film fabrication.

Effects of Substrate Temperature on Properties of Transparent Conductive Ta-Doped TiO_2 Films Deposited by Radio-Frequency Magnetron Sputtering

Ta-doped titanium dioxide films are deposited on fused quartz substrates using the rf magnetron sputtering technique at different substrate temperatures. After post-annealing at 550℃ in a vacuum, all the films are crystallized into the polycrystalline anatase TiO2 structure. The effects of substrate temperature from room temperature up to 350℃ on the structure, morphology, and photoelectric properties of Ta-doped titanium dioxide films are analyzed. The average transmittance in the visible region（400-800 nm） of all films is more than 73%.The resistivity decreases firstly and then increases moderately with the increasing substrate temperature. The polycrystalline film deposited at 150℃ exhibits a lowest resistivity of 7.7 × 10^-4Ω·cm with the highest carrier density of 1.1×10^21 cm^-3 and the Hall mobility of 7.4 cm^2·V^-1s^-1.

THE STUDY OF THE NON-STEADY KINETICS OF THE OXYDEHYDROGENATION OF ETHANE TO ETHYLENE OVER THE CATALYST OF Mo-V-Nb/Al_2O_3 BY THE TECHNIQUE OF TEMPERATURE PROGRAMMED TRANSIENT RESPONSE AND ELECTRIC CONDUCTIVITY

In this paper, instead of with the more expensive Fourier Transform Infrared Spectrometer(FTIR) a new technique of Temperature Programmed Transient Response(TP-TR) has been used with gas chromatography. Therefore, the TP-TR will be applied more widespreadly than ever before. With the technique of TP-TR and electric conductivity, the study is on the reaction mechanism and the adsorption behavior of the reactants and products to the present catalyst Mo-V-Nb/Al_2O_3 in the reaction from ethane through oxydehydrogenation to ethylene as the product. By Range-Kutta-Gill and Margarat methods, the kinetic parameters of the reaction elementary steps (i.e. rate constants, active energies and frequency factors) have been evaluated. The mathematical treatment coincides with the experimental results.

Defect chemistry engineering of Ga-doped garnet electrolyte with high stability for solid-state lithium metal batteries

Ga-doped Li_(7)La_(3)Zr_(2)O_(12)(Ga-LLZO)has long been considered as a promising garnet-type electrolyte candidate for all-solid-state lithium metal batteries(ASSLBs)due to its high room temperature ionic conductivity.However,the typical synthesis of Ga-LLZO is usually accompanied by the formation of undesired LiGaO_(2) impurity phase that causes severe instability of the electrolyte in contact with molten Li metal during half/full cell assembly.In this study,we show that by simply engineering the defect chemistry of Ga-LLZO,namely,the lithium deficiency level,LiGaO_(2) impurity phase is effectively inhibited in the final synthetic product.Consequently,defect chemistry engineered Ga-LLZO exhibits excellent electrochemical stability against lithium metal,while its high room temperature ionic conductivity(~1.9×10^(-3)S·cm^(-1))is well reserved.The assembled Li/Ga-LLZO/Li symmetric cell has a superior critical current density of 0.9 mA·cm^(-2),and cycles stably for 500 hours at a current density of 0.3 mA·cm^(-2).This research facilitates the potential commercial applications of high performance Ga-LLZO solid electrolytes in ASSLBs.

Effects of lime treatment on the microstructure and hydraulic conductivity of Héricourt clay

This study aims at evidencing the effects of lime treatment on the microstructure and hydraulic conductivityof a compacted expansive clay, with emphasis put on the effect of lime hydration and modification.For this purpose, evolutions of hydraulic conductivity were investigated for both lime-treatedand untreated soil specimens over 7 d after full saturation of the specimens and their microstructureswere observed at the end. Note that for the treated specimen, dry clay powder was mixed with quicklimeprior to compaction in order to study the effect of lime hydration. It is observed that lime hydration andmodification did not affect the intra-aggregate pores but increased the inter-aggregates pores size. Thisincrease gave rise to an increase of hydraulic conductivity. More precisely, the hydraulic conductivity oflime-treated specimen increased progressively during the first 3 d of modification phase and stabilisedduring the next 4 d which correspond to a short period prior to the stabilisation phase. The microstructureobservation showed that stabilisation reactions took place after 7 d. Under the effect of stabilisation,a decreasing hydraulic conductivity can be expected in longer time due to the formation ofcementitious compounds. 2014 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. All rights reserved.

Effect of carboxymethyl cellulose on dissolution kinetics of carboxymethyl cellulose-sodium carbonate two-component tablet

Sodium carbonate and carboxymethyl cellulose powders are compressed into two-component tablets with three mass ratios,97%:3%,95%:5% and 93%:7%.The dissolution tests for two-component tablets and reference pure sodium carbonate tablets are carried out at various temperatures.The dissolution process of each tablet is measured by electrical conductivity tracking method and the concentration of dissolved sodium carbonate is quanti fied with calibrated conductivity-concentration converting equation of sodium carbonate.The quanti fied dissolution data is fitted with both surface reaction model and diffusion layer model and the results clearly show that surface reaction model is suggested as the appropriate dissolution model for all measured tablets.Therefore,it is determined that carboxymethyl cellulose is a stable element to remain the dissolution mechanism of tablet unchanged.The dissolution rate constant quanti fied with surface reaction model presents that carboxymethyl cellulose-sodium carbonate two-component tablets obtain signi ficant higher dissolution rate constant than pure sodium carbonate tablet and higher proportion of carboxymethyl cellulose leads to apparent higher dissolution rate constant.The results prove for the usage of carboxymethyl cellulose in most practical applications at a relative low-level,the effect of carboxymethyl cellulose is effective and positive for two-component tablet to enhance the dissolution process and improve dissolution rate constant and this effect is speculated coming from its dynamic physical transforming process in water including dilation and conglutination.

Study on Rare Earth Interconnector of La_(1 -x)Ca_xCrO_3

As an interconnector of solid oxide fuel cell, La 1-x Ca x CrO 3( x =0 0～0 5) were prepared by sol gel method. The crystal structures of La 1-x Ca x CrO 3 at room temperature are the orthorhombic perovskite GdFeO 3 type. XPS analysis indicates that chrome ions are in different valence state. The introduction of Ca 2+ into the lattice induces the oxidation of Cr 3+ to Cr 6+ . With x increasing, the amount of Cr 6+ increases. The present of the more Cr 6+ is one of the important factors that effect electric conductivity of La 1-x Ca x CrO 3.

Methods to Improve the Long Distance Time-Varying Channel Transmission Performance of Expendable Profiler

To improve the transmission performance of XCTD channel, this paper proposes a method to measure directly and fit the channel transmission characteristics by using frequency sweeping method. Sinusoidal signals with a frequency range of 100 Hz to 10 k Hz and an interval of 100 Hz are used to measure transmission characteristics of channels with lengths of 300 m, 800 m, 1300 m, and 1800 m. The correctness of the fitted channel characteristics by transmitting square wave, composite waves of different frequencies, and ASK modulation are verified. The results show that when the frequency of the signal is below 1500 Hz, the channel has very little effect on the signal. The signal compensated for amplitude and phase at the receiver is not as good as the uncompensated signal.Alternatively, when the signal frequency is above 1500 Hz, the channel distorts the signal. The quality of signal compensated for amplitude and phase at receiver is better than that of the uncompensated signal. Thus, we can select the appropriate frequency for XCTD system and the appropriate way to process the received signals. Signals below1500 Hz can be directly used at the receiving end. Signals above 1500 Hz are used after amplitude and phase compensation at the receiving end.

Heat transfer of nanofluidics in hydrophilic pores: Insights from molecular dynamics simulations

Nanofluidics in hydrophilic nanopores is a common issue in many natural and industrial processes. Among all,the mass transport of nanofluidics is most concerned. Besides that, the heat transfer of a fluid flow in nano or micro channels is always considered with adding nanoparticles into the flow, so as to enhance the heat transfer by convection between the fluid and the surface. However, for some applications with around 1 nm channels such as nano filtration or erosion of rocks, there should be no nanoparticles included. Hence, it is necessary to figure out the heat transfer mechanism in the single phase nanofluidics. Via non-equilibrium molecular dynamics simulations, we revealed the heat transfer inside nanofluidics and the one between fluid and walls by setting simulation into extremely harsh condition. It was found that the heat was conducted by molecular motion without temperature gradient in the area of low viscous heat, while it was transferred to the walls by increasing the temperature of fluids. If the condition back to normal, it was found that the viscous heat of nanofluidics could be easily removed by the fluid-wall temperature drop of less than 1 K.

Hybridization between microstructure and magnetization improvement in lead and RE co-doped BiFeO_3

The crystal structure,magnetic and electrical properties of Bi（0.96）Pb（0.04） FeO3 and Bi（0.92）Pb（0.04）RE（0.04）FeO3（RE=La,Sm,Dy and Yb）polycrystalline samples were prepared by the flash autocombustion technique.X-ray diffraction（XRD）measurements show that the rare-earth doped compositions crystallized in rhombohedral symmetry of space group R3 c.The undoped sample consisted needle shape particles while rare earth substitution preferred platelet like particles as clarified from high resolution transmission electron microscopy（HRTEM）.Morphological features were examined using field emission scanning electron microscopy（FESEM）.Magnetization measurements showed that Yb^3＋ samples possessed the highest room temperature saturation magnetization while when Bi^3＋ ions were substituted by La^3＋ ions,a smaller MS（0.28 emu/g）was obtained.The coexistence of ferroelectric and magnetic transitions was detected using DSC and χM,indicating the multiferroic characteristics of Bi（0.92）Pb（0.04）RE（0.04）FeO3 crystallites.The Néel temperature shifted upwards with decreasing the ionic radius of rare earth ion.Nice correlation was established between microstructure,morphology and magnetic properties in view of the contribution of magnetocrystalline and shape anisotropy in the magnetic parameters values.

Electrical conductivities of two granite samples in southern Tibet and their geophysical implications

There are clear differences in the electrical conductivities of the crustal granites of the Qinghai-Tibet Plateau.Because these granites are among the major rock types on the Qinghai-Tibet Plateau, it is very important to detect the electrical conductivity of granites under high temperatures and pressures to study the electrical conductivity structure of this area. Using impedance spectroscopy at a frequency range of 10.1–106 Hz, the electrical conductivity of the muscovite-granite collected from Yadong was investigated at a confining pressure of 1.0 GPa and temperatures ranging from 577 to 996 K, while the electrical conductivity of the biotite-granite collected from Lhasa was investigated at a pressure of 1.0 GPa and temperatures ranging from587 to 1382 K. The calculated activation enthalpies of the Yadong muscovite-granite sample is 0.92 eV in the low-temperature range(577–919 K) and 2.16 eV in the high-temperature range(919–996 K). The activation enthalpies of the Lhasa biotite-granite sample is 0.48 eV in the low-temperature range(587–990 K) and 2.06 eV in the high-temperature range(990–1382 K). The change in the activation enthalpies of the granites at different temperature ranges may be associated with the dehydration of the two samples. The electrical conductivities of the granite samples obtained in the laboratory using impedance spectroscopy correspond well with field observations conducted near the sampling points, both in terms of the actual conductivity values and the observed variations between the low-temperature and high-temperature regimes. This correlation of laboratory and field conductivities indicates that the conductivities of the crustal rocks in the two regions closely correspond to granite conductivities.We calculated the electrical conductivities of muscovite-granite and biotite-granite samples using the effective medium and HS boundary models. When applied to the crustal rocks of southern Tibet, the results of the geophysical conductivity profiles lie within the range of laboratory data. Thus, the electrical characteristics of the crustal rocks underlying the southern Qinghai-Tibet Plateau can largely be attributed to granites, with the large changes to high conductivities at increasing depths resulting from the dehydration of crustal rocks with granitic compositions.

Reduction in thermal conductivity of monolayer WS_(2) caused by substrate effect

Understanding the substrate and temperature effect on thermal transport properties of transition metal dichalcogenides(TMDs)monolayers are crucial for their future applications.Herein,a dual-wavelength flash Raman(DF-Raman)method is used to measure the thermal conductivity of monolayer WS_(2) at a temperature range of 200–400 K.High measurement accuracy can be guaranteed in this method since the influence of both the laser absorption coefficient and temperature-Raman coefficient can be eliminated through normalization.The room-temperature thermal conductivity of suspended and supported WS_(2) are 28.5±2.1(30.3±2.0)and 15.4±1.9(16.9±2.1)W/(m·K),respectively,with a~50%reduction due to substrate effect.Molecular dynamics(MD)simulations reveal that the suppression of acoustic phonons is mainly responsible for the striking reduction.The behaviors of optical phonons are also unambiguously investigated using Raman spectroscopy,and the in-plane optical mode,E(Γ),is surprisingly found to be slightly enhanced while out-of-plane mode,A1g(Γ),is suppressed due to substrate interaction,mutually verified with MD results.Our study provides a solid understanding of the phonon transport behavior of WS_(2) with substrate interaction,which provides guidance for TMDs-based nanodevices.