Simulation of Temperature and Flow Field by Three Dimension Finite ElementMethod for Castex Process of AS Wire

Castex of AS wire is a new technology of near net shape. To study the variation of temperature and velocity of liquid (or semisolid) aluminum during dynamic solidification the numerical simulation was carried out with the theory of heat-transfer and hydrodynamics by means of 3-dimensional finite element method. From simulation results, it is found that the variation of temperature and velocityis mainly influenced by the casting temperature of aluminum, rotating speed of Castex wheel and flow of cooling water. Among theseinfluencing factors, the casting temperature distributes most to the length of liquid phase metal. Moreover, the faster the metal solidifies,the higher the metal there moves with the overall trend of descending from the bottom of the wheel to the shoe wall as well as from sidewalls to the center of wheel groove. In comparison with the practical value, the simulation is reliable.

SIMULATION ON HEATING PROCESS IN ULTRASONIC WELDING OF PLASTICS

The energy conversion during ultrasonic plastic welding is analyzed on the basis of the theory of vis- coelastic mechanics,.The temperature field and the temperature change of the ABS specimen with ener- gy director during ultrasonic welding is simulated with finite element method(FEM). In the simu- lation process,the melting of the energy energy is also considered. The calculation results are in good agreement with the temperature measurement results, which proves that the simulation results are reli- able.

Combined effects of elevated temperature and CO_2 concentration on Cd and Zn accumulation dynamics in Triticum aestivum L.

A simulated climate warming experiment was conducted to evaluate the combined effects of elevated temperature and CO_2 concentration on the bioaccumulation,translocation and subcellular distributions of Cd and Zn in wheat seedlings（Triticum aestivum L.cv.Xihan 1.） at Dingxi,Gansu Province,China.The objective was to find evidence that global climate change is affecting the bioaccumulation of Cd and Zn in T.aestivum L.cv.Xihan 1.The results showed that compared to control A,elevated temperature and CO_2 increased Cd bioaccumulation in the shoots by 1.4–2.5 times,and increased that in the roots by 1.2–1.5times,but decreased Zn levels in wheat shoots by 1.4–2.0 times,while decreased that in the roots by 1.6–1.9 times.Moreover,temperature and CO_2 concentration increase also led to increased Cd concentration,and decreased Zn concentration in subcellular compartments of wheat seedlings.The largest Cd concentration increase（174.4%） was observed in the cell wall and debris fractions of shoots after they were subjected to the highest CO_2 and temperature treatment（TC3）.The largest Zn concentration decrease（53.1%） was observed in the soluble（F3） fractions of shoots after they were subjected to the medium CO_2 and temperature treatment（TC2）.The temperature and CO_2 increase had no significant effect on the proportional distribution of Cd and Zn in the subcellular fractions.The root-to-shoot translocation of Cd increased with the increasing temperature and CO_2 concentration.However,the Zn distributions only fluctuated within a small range.

Temperature stability of magnetic field for periodic permanent-magnet focusing system

In this study, finite element analysis based on an Ansoft Maxwell software was used to reveal the temperature stability of a magnet ring and the equivalent structural periodic permanent-magnet（PPM） focusing system. It is found that with the temperature increasing, the decrease rate of magnetic induction peak（Bz）maxof single magnet ring is greater than that of remanence Brof magnet in the range from room temperature to 200 °C, however,the PPM focusing system do have the same temperature characteristics of permanent-magnet materials. It indicates that the magnetic temperature properties of the PPM system can be effectively controlled by adjusting the temperature properties of the magnets. Moreover, the higher permeability of the magnets indicates the less Hcb, giving rise to lower magnetic induction peak （Bz）′max： Finally, it should be noted that the magnetic orientation deviation angle θ（／15°） of permanent magnets has little effect on the focusing magnetic field of the PPM system at different temperatures and the temperature stability. The obtained results are beneficial to the design and selection of permanent magnets for PPM focusing system.

Temperature Field of PC Box Girder Bridge Based on GPRS Temperature Collection System

In order to study the temperature distribution and the corresponding temperature effects on pre-stressed concrete（PC） curved box girder bridge in Shandong Province, this paper builds and adopts an automatic remote real-time temperature collection system to collect temperature data on site, and further uses the software ANSYS for analysis. Based on the comparisons between the measured data and the simulation results, the following conclusions can be drawn： 1 Our temperature monitoring system is reliable; 2 The corresponding measured data of the web plate and flange plate exposed to the sun, vary more severely than that at other positions, so these plates need higher standard design and construction requirements; 3 In the cold wave where still is sunshine, the box girder temperature effect behaves as sine-like curve.

Thermo-elasto-visco-plastic finite element analysis on formation and propagation of off-corner subsurface cracks in bloom continuous casting

The formation and propagation of the popular off-corner subsurface cracks in bloom continuous casting were investigated through thermo-mechanical analysis using three coupled thermo-mechanical models. A two-dimensional thermo-elasto-visco-plastic finite element model was developed to predict the mould gap evolution, temperature profiles and deformation behavior of the solidified shell in the mould region. Then, a three-dimensional model was adopted to calculate the shell growth, tempera- ture history and the development of stresses and strains of the shell in the following secondary cooling zones. Finally, another three-dimensional model was used to analyze the stress distributions in the straightening region, The results showed that the off-corner cracks in the shell originated from the mould owing to the tensile strain developed in the crack sensitive regions of the solidification front, and they could be driven deeper by the possible severe surface temperature rebound and the extensive tensile stress in the secondary cooling zone, especially upon the straightening operation of the bloom casting. It is revealed that more homogenous shell temperature and thickness can be obtained through optimization of mould corner radius, casting speed and secondary cooling scheme, which help to decrease stress and strain concentration and therefore prevent the initiation of the cracks.