Microstructural Changes of Graphene/PLA/PBC Nanofibers by Electrospinning during Tensile Tests

This study focuses on the nanostructure and nanostructural changes of novel graphene/poly（lactic acid） （PLA）/ poly（butylene carbonate） （PBC） nanofibers via electrospinning, which are characterized by differential scanning calorimetry （DSC）, scanning electron microscopy （SEM）, tensile test and in situ small angle x-ray scattering. DSC indicates that the endothermic peak at 295℃ of pure PLA/PBC nanofibers shifted from 317℃ to lower 290℃ with the increasing graphene content. SEM observations reveal a fine dispersion of graphene in the nanofiber matrices. The graphene/PLA/PBC nanofiSers exhibit good improvements in mechanical property. The tensile strength of nanofibers increases with the addition of 0.01 g graphene but reduces with further addition of 0.04g graphene. The scattering intensities increase dramatically when the strain levels are higher than the yield point due to the nucleation and growth of nanovoids or crystals. However, the increasing content of graphene in the PLA/PBC matrix provokes a strong restriction to the deformation-induced crystals.

A METHOD TO QUANTIFY CRAZING DEFORMATION BY TENSILE TESTS FOR POLYSTYRENE/POLYOLEFIN ELASTOMER IMMISCIBLE BLENDS

A method to quantify crazing deformations by tensile tests for polystyrene （PS） and polyolefin elastomer （POE） blends was investigated. The toughness of PS/POE blends, reflected by the Charpy impact strength, increased with the content of POE. SEM micrographs showed the poor compatibility between PS and POE. In simple tensile tests, it is very easy to achieve the ratio of crazing deformation, i.e. K by measuring the size changes of samples. The K values decreased with increasing the content of POE, and the deformations of PS/POE blends were dominated by crazing. The plots of the change of volume （△V） against longitudinal variation （△I） showed a linear relationship, and the slope of lines decreased with the content of POE. Measuring samples at the tensile velocities of 5 mm/min, 50 mm/min, and 500 mm/min respectively, the K values kept unchanged for each PS/POE blends.

Tensile strength and failure behavior of rock-mortar interfaces: Direct and indirect measurements

The tensile strength at the rock-concrete interface is one of the crucial factors controlling the failure mechanisms of structures,such as concrete gravity dams.Despite the critical importance of the failure mechanism and tensile strength of rock-concrete interfaces,understanding of these factors remains very limited.This study investigated the tensile strength and fracturing processes at rock-mortar interfaces subjected to direct and indirect tensile loadings.Digital image correlation(DIC)and acoustic emission(AE)techniques were used to monitor the failure mechanisms of specimens subjected to direct tension and indirect loading(Brazilian tests).The results indicated that the direct tensile strength of the rock-mortar specimens was lower than their indirect tensile strength,with a direct/indirect tensile strength ratio of 65%.DIC strain field data and moment tensor inversions(MTI)of AE events indicated that a significant number of shear microcracks occurred in the specimens subjected to the Brazilian test.The presence of these shear microcracks,which require more energy to break,resulted in a higher tensile strength during the Brazilian tests.In contrast,microcracks were predominantly tensile in specimens subjected to direct tension,leading to a lower tensile strength.Spatiotemporal monitoring of the cracking processes in the rock-mortar interfaces revealed that they show AE precursors before failure under the Brazilian test,whereas they show a minimal number of AE events before failure under direct tension.Due to different microcracking mechanisms,specimens tested under Brazilian tests showed lower roughness with flatter fracture surfaces than those tested under direct tension with jagged and rough fracture surfaces.The results of this study shed light on better understanding the micromechanics of damage in the rock-concrete interfaces for a safer design of engineering structures.

Probing into the Yield Plateau Phenomenon in Commercially Pure Titanium During Tensile Tests

To explain the intrinsic mechanism of the yield plateau phenomenon in commercially pure titanium,the tensile behaviors of commercially pure titanium specimens after 91.6%cryorolling and subsequent annealing at 280℃,335℃,450℃and 600℃have been studied.The results show that the yield plateau phenomenon is a result of dislocation behaviors controlled by grain size and thus only exists within a given range of mean grain size.αgrain boundaries are the main dislocation multiplication sources of commercially pure titanium.Fine-grained microstructure could offer numerous dislocation multiplication locations during deformation.Once the applied stress is above the yielding strength,dislocations multiply rapidly and the mobile dislocation density is high.To retrieve the imposed strain rate,the mean dislocation velocity is bound to be low.Therefore,it takes time for them to interact with each other.As a result,the movement of dislocations is hardly blocked and the deformation could continue at a nearly constant applied stress.Consequently,the so-called yield plateau behavior presents in the tensile curves.The disappearance of yield plateau phenomenon in coarse-grained and ultrafi ne-grained microstructures is attributed to the quick realization of the mutual interactions among dislocations at the initial stage of tensile test.

Isogeometric Analysis of Hyperelastic Material Characteristics for Calcified Aortic Valve

This study explores the implementation of computed tomography(CT)reconstruction and simulation techniques for patient-specific valves,aiming to dissect the mechanical attributes of calcified valves within transcatheter heart valve replacement(TAVR)procedures.In order to facilitate this exploration,it derives pertinent formulas for 3D multi-material isogeometric hyperelastic analysis based on Hounsfield unit(HU)values,thereby unlocking foundational capabilities for isogeometric analysis in calcified aortic valves.A series of uniaxial and biaxial tensile tests is executed to obtain an accurate constitutive model for calcified active valves.To mitigate discretization errors,methodologies for reconstructing volumetric parametric models,integrating both geometric and material attributes,are introduced.Applying these analytical formulas,constitutive models,and precise analytical models to isogeometric analyses of calcified valves,the research ascertains their close alignment with experimental results through the close fit in displacement-stress curves,compellingly validating the accuracy and reliability of the method.This study presents a step-by-step approach to analyzing themechanical characteristics of patient-specific valves obtained fromCT images,holding significant clinical implications and assisting in the selection of treatment strategies and surgical intervention approaches in TAVR procedures.

Study of the Characteristics of Large-Diameter Iron Bars Obtained by Rolling at the ODHAV Foundry in the Republic of Guinea

This work consists of evaluating the quality of the mechanical parameters of large-diameter steels, i.e. 20, 25, 28 and 32, through a process of recycling scrap metal that fills garages, rubbish dumps, gutters and other abandoned sites, as well as imported concrete reinforcing steel sold in the Republic of Guinea. To carry out this important work, a number of mechanical tensile and bending tests and a microscopic analysis combining two devices, an electron microscope and a photographic camera, were carried out. The samples were taken from sampling areas in the major communes of Conakry, namely: Casse Sonfonia, Matoto and Kagbélen. The tensile strength values of the large dimensions 20, 25, 28 and 32 are given in the tables.

Development of Morus alba Reinforced Poly-Lactic Acid with Elevated Mechanical and Thermal Properties

This research investigates the mechanical and thermal properties of Morus alba combined with polylactic acid in comparison with other natural fibers. The study uses three different fiber and PLA compositions - 20%, 30%, and 40% respectively - to produce composite materials. In addition, another composite with the same fiber volume is treated with a 4% NaOH solution to improve mechanical properties. The composites are processed by twin-screw extrusion, granulation, and injection molding. Tensile strength measurements of raw fibers and NaOH-treated fibers were carried out using a single-fiber tensile test with a gauge length of 40 mm. It was observed that the NaOH surface treatment increases the resistance against tensile loading and exhibited improved properties for raw fiber strands. The diameter of the fibers was measured using optical microscopy. During this research, flexural tests, impact tests, differential scanning calorimetry (DSC), and heat deflection temperature measurements (HDT) were conducted to evaluate the mechanical and thermal properties of the developed composite samples. The results indicate that the mechanical properties of NaOH-treated Morus alba-reinforced polylactic acid outperform both virgin PLA samples and untreated Morus alba samples.

Effects of ultrasonic vibration on plastic deformation of AZ31 during the tensile process

An investigation on the plastic behavior of AZ31 magnesium alloy under ultrasonic vibration（with a frequency of 15 kHz and a maximum output of 2 kW） during the process of tension at room temperature was conducted to reveal the volume effect of the vibrated plastic deformation of AZ31.The characteristics of mechanical properties and microstructures of AZ31 under routine and vibrated tensile processes with different amplitudes were compared.It is found that ultrasonic vibration has a remarkable influence on the plastic behavior of AZ31 which can be summarized into two opposite aspects：the softening effect which reduces the flow resistance and improves the plasticity,and the hardening effect which decreases the formability.When a lower amplitude or vibration energy is applied to the tensile sample,the softening effect dominates,leading to a decrease of AZ31 deformation resistance with an increase of formability.Under the application of a high-vibrating amplitude,the hardening effect dominates,resulting in the decline of plasticity and brittle fracture of the samples.

TENSILE PROPERTIES AND CREEP RESISTANCE OF AZ91 ALLOY CONTAINING ANTIMONY

Small amount of antimony addition to the Mg-9Al-0.8Zn-0.2Mn(AZ91) alloy results in the obvious increase of tensile strength at both ambient and elevated temperatures. The creep resistance at the temperatures up to 200°C is also improved significantly by antimony addition. Microstructural observations revealed that the addition of antimony modifies morphology of the β(Mg17Al12) phase and causes the formation of some rod-shaped precipitates Mg3Sb2 at grain boundaries. These precipitates have high thermal stability and play an important role for strengthening grain boundaries at elevated temperatures.

TENSILE STRESS RELAXATION OF TURBINE BOLT STEELS AT HIGH TEMPERATURE

Stress relaxation behavior of two turbine bolt steels was evaluated by the manual-controlled tensile stress relaxation test (TSRT) at high temperature. First, feasibility and the procedure of the manual-controlled tensile stress relaxation test (TSRT) is discussed and carried out on a general creep testing machine. And then, the experimental results from such type of test were compared to the existing data provided by certain Laboratory U.K. Overall good agreement between the results of manual-controlled TSRT method and the existing data provides confidence in the use of the proposed method in practice. Finally, the experimental results of turbine bolt steels from TSRT were compared with that of bending test. It is observed that great difference exists between the results from two different type stress relaxation tests. It is therefore suggested that the results from TSRT method be adopted in turbine bolt design in engineering.

Effect of discrete fibre reinforcement on soil tensile strength

The tensile behaviour of soil plays a significantly important role in various engineering applications. Compacted soils used in geotechnical constructions such as dams and clayey liners in waste containment facilities can suffer from cracking due to tensile failure. In order to increase soil tensile strength, discrete fibre reinforcement technique was proposed. An innovative tensile apparatus was developed to deter- mine the tensile strength characteristics of fibre reinforced soil. The effects of fibre content, dry density and water content on the tensile strength were studied. The results indicate that the developed test apparatus was applicable in determining tensile strength of soils. Fibre inclusion can significantly in- crease soil tensile strength and soil tensile failure ductility. The tensile strength basically increases with increasing fibre content. As the fibre content increases from 0% to 0.2%, the tensile strength increases by 65.7%. The tensile strength of fibre reinforced soil increases with increasing dry density and decreases with decreasing water content. For instance, the tensile strength at a dry density of 1.7 Mg/m^3 is 2.8 times higher than that at 1.4 Mg/m^3. It decreases by 30% as the water content increases from 14.5% to 20.5%. Furthermore, it is observed that the tensile strength of fibre reinforced soil is dominated by fibre pull-out resistance, depending on the interracial mechanical interaction between fibre surface and soil matrix.

Study on the Forming Limit Nomogram of Tensile Stamping Operations

Based on plasticity theory and physical experiments, the quantitative relationships between elongation δ obtained byuniaxial tensile test and forming limits of tensile stamping operations are given, which mainly resolves the problem thatforming limits can be derived from simple tensile test. The forming limit nomogram of tensile stamping operationsis also established to apply to engineering.

Process Evaluation, Tensile Properties and Fatigue Resistance of Chopped and Continuous Fiber Reinforced Thermoplastic Composites by 3D Printing

The aim of this article was to comprehensively evaluate the manufacturing process,tensile properties and fatigue resistance of the chopped and continuous fiber reinforced thermoplastic composites(CFRTPCs)by 3D printing.The main results included:the common defects of the printed CFRTPCs contained redundant and accumulation defects,scratch and warping defects;the continuous fiber contributed to the dimensional stability and accuracy of width and thickness;associations between mass percentage of fiber reinforcement and the averages of elastic mod-ulus,strain at break and ultimate tensile strength were approximately linear based on tensile test results;the fati-gue resistance improved with the increasing fiber reinforcement based on fatigue test results.As for specimens with four fiber rings,there was a good linear relationship between the stress level and logarithm value of cycles during the whole life while those of pure matrix and specimens with one and two fiber rings were piecewise linear,taking about 10,000 cycles as boundary.The micro morphology showed that the fatigue failure behaved as matrix fracture,large and small fiber bundles and single fibers extracted from matrix.Under the tension-tension fatigue load,the deformations where easily concentrating stress behaved as sunken surfaces along thickness and width directions,and the deformation along width direction was greater than that along thickness direction.

Analysis on the deformation and fracture behavior of carbon steel by in situ tensile test

The deformation and fracture behaviors of low-carbon steel, medium-carbon steel, and high-carbon steel were studied on internal microstructure using the scanning electron microscopy in situ tensile test. The microstructure mechanism of their deformation and fracture behavior was analyzed. The results show that the deformation and fracture behavior of low-carbon steel depends on the grain size of ferrite, the deformation and fracture behavior of medium-carbon steel depends on the size of ferrite grain and pearlite lump, and the deformation and fracture behavior of high-carbon steel depends on the size of pearlite lump and the pearlitic interlamellar spacing.

Magnetic Technique Estimation of Weld Residual Stress Failure Due to Tensile Loading

In Nigeria, most welding activities are carried out by road side welders, majority of this welders are ignorant of weld residual stress and its adverse effect on weldment. Residual stress (RS) measuring device is vital in the measurement of inherent stresses in material. The aim of this research was to employ proof of principle in analyzing the weld residual stresses in a material. This was achieved by measuring samples with magnetic residual stress device and then subjecting the weld samples to mechanical tensile test with hope that materials with more residual stresses fail first. Finally the result from both procedures was compared to establish a relationship. Four (4) pieces of mild steel coupons measuring 100 × 40 × 3 mm were welded, producing two specimens, A11 and B11 of 200 × 40 × 3 mm, respectively. The specimens were measured using the Magnetic device developed and 37 signals were obtained per specimen, thereafter, the welded specimens were subjected to tensile testing and results analyzed. From the results obtained, Specimen A11 was observed to have the highest signal peak at the weld zone with RS signal of 20.3983 mV compared to B11 with 19.358 mV. While under tensile loading, it took 1.63 kN to cause failure to specimen A11 and 8.65 kN for specimen B11. From this simple experiment, it implies that the Magnetic RS device was able to mimic the behavior of residual stress and also predicted that A11 would fail first.

Tensile properties and fracture reliability of a glass-coated Co-based amorphous microwire

Co68.15Fe4.35Si12.25B15.25 （at%） amorphous microwires with a smooth surface and a circular cross-section were fabricated by the glass-coated melt spinning method. Their mechanical properties were evaluated through tensile tests of the glass-coated amorphous mi-crowires, and their fracture reliability was estimated using two-and three-parameter Weibull analysis. X-ray diffraction and transmission electron microscopy results showed that these glass-coated Co-based microwires were mostly amorphous. The coated Co-based microwires exhibit a tensile strength of 1145 to 2457 MPa, with a mean value of 1727 MPa and a variance of 445 MPa. Weibull statistical analysis showed that the tensile two-parameter Weibull modulus of the amorphous microwires is 4.16 and the three-parameter Weibull modulus is 1.61 with a threshold value as high as 942 MPa. These results indicate that the fabricated microwires exhibit good tensile properties and fracture reliability, and thus appear to be good candidates for electronics reliability engineering applications.

Tensile and compressive behavior of Ti-based bulk metallic glass composites

This article focuses on the tensile and compressive characteristics of a Ti-based bulk metallic glass composite （BMGC）. It is found that the yield stress, maximum strength, and fracture strain are 1380 MPa, 1516 MPa, and 4.3% for uniaxial tension, but 1580 MPa, 4010 MPa, and 29% for uniaxial compression, respectively. The composite displays a linear ＂work hardening＂ capacity under compression; however, the ＂work softening＂ behavior is observed in the true engineering stress-strain curve upon tensile loading. The fracture surfaces of specimens also exhibit dissimilar properties under the different loadings.

TENSILE TESTING OF C/C COMPOSITES AT HIGH TEMPERATURES

The tensile properties of three different carbonfiberreinforced carbon composites (C/C), mat C/C, 2D laminate and 4D C/C, were investigated under the combined influence of temperature and loading rate. From the experiments the following could be concluded: loading rate between 10-1-10 mm/min was valid; the fracture stress of the three kinds of C/C composites increased with increasing temperature in the range from room temperature to 1900, and the initial modulus of 2D laminate C/C composites increased with the increase of temperature up to 2000.

Study of Deformation Coating for Sheets by Using Tensile Test

This article focuses on the study of the defined values of tensile strain and the effect of low temperature plasma adhesion selected coatings on steel samples using a tensile testing flat test bars. Samples were made by machining and welding technologies. The flat test bars were tested by pulling on a test rig UPC 1200. Part of the samples was treated on the surface prior to coating by a tensile test, second base coat and with a final coat continuous multi plasma system. The selected test samples were determined from the tensile test of the material characteristics apparent from the tensile diagrams. The examined samples were fitted top and base coat. Another group was the KTL basis. The presented graphs show the dependence of the strength on elongation of a sample according to DIN EN ISO 6892-2. The samples were then examined under a stereo microscope SCHUT brand, type SSM-E in the laboratory to conduct coating on a steel sheet at the moment of total violation sectional samples. The base layer, in which the temperature ranges from 160°C - 180°C, was applied by electrophoresis method.

Mechanical characteristic and failure mechanism of joint with composite sucker rod

Composite sucker rods are widely used in oil fields because of light weight,high strength,and corrosion resistance.Bonded technology becomes the primary connection method of composites.However,the joints with composite sucker rods are prone to debone and fracture.The connected characteristics are less considered,so the failure mechanism of the joint is still unclear.Based on the cohesive zone model(CZM)and the Johnson-Cook constitutive model,a novel full-scale numerical model of the joint with composite sucker rod was established,and verified by pull-out experiments.The mechanical properties and slip characteristics of the joint were studied,and the damaged procession of the joint was explored.The results showed that:a)the numerical model was in good agreement with the experimental results,and the error is within 5%;b)the von Mises stress,shear stress,and interface stress distributed symmetrically along the circumferential path increased gradually from the fixed end to the loading end;c)the first-bonded interface near the loading end was damaged at first,followed by debonding of the second-bonded interface,leading to the complete shear fracture of the epoxy,and resulted in the debonding of the joint with composite sucker rod,which can provide a theoretical basis for the structural design and optimization of the joint.