Buckling Properties of Water-Drop-Shaped Pressure Hulls with Various Shape Indices Under Hydrostatic External Pressure

The water-drop-shaped pressure hull has a good streamline,which has good application prospect in the underwater observatory.Therefore,this study conducted analytical,experimental and numerical investigation of the buckling properties of water-drop-shaped pressure hulls under hydrostatic pressure.A water-drop experiment was conducted to design water-drop-shaped pressure hulls with various shape indices.The critical loads for the water-drop-shaped pressure hulls were resolved by using Mushtari’s formula.Several numerical simulations including linear buckling analysis and nonlinear buckling analysis including eigenmode imperfections were performed.The results indicated that the critical loads resolved by Mushtari's formula were in good agreement with the linear buckling loads from the numerical simulations.This formula can be extended to estimate the buckling capacity of water-drop-shaped pressure hulls.In addition,three groups of pressure hulls were fabricated by using stereolithography,a rapid prototyping technique.Subsequently,three groups of the pressure hulls were subjected to ultrasonic measurements,optical scanning,hydrostatic testing and numerical analysis.The experimental results were consistent with the numerical results.The results indicate that the sharp end of the water-drop-shaped pressure hulls exhibited instability compared with the blunt end.This paper provides a new solution to the limitations of experimental studies on the water-drop-shaped pressure hulls as well as a new configuration and evaluation method for underwater observatories.

Evaluation of frictional pressure drop correlations for air-water and air-oil two-phase flow in pipeline-riser system

Accurate prediction of the frictional pressure drop is important for the design and operation of subsea oil and gas transporting system considering the length of the pipeline. The applicability of the correlations to pipeline-riser flow needs evaluation since the flow condition in pipeline-riser is quite different from the original data where they were derived from. In the present study, a comprehensive evaluation of 24prevailing correlation in predicting frictional pressure drop is carried out based on experimentally measured data of air-water and air-oil two-phase flows in pipeline-riser. Experiments are performed in a system having different configuration of pipeline-riser with the inclination of the downcomer varied from-2°to-5°to investigated the effect of the elbow on the frictional pressure drop in the riser. The inlet gas velocity ranges from 0.03 to 6.2 m/s, and liquid velocity varies from 0.02 to 1.3 m/s. A total of885 experimental data points including 782 on air-water flows and 103 on air-oil flows are obtained and used to access the prediction ability of the correlations. Comparison of the predicted results with the measured data indicate that a majority of the investigated correlations under-predict the pressure drop on severe slugging. The result of this study highlights the requirement of new method considering the effect of pipe layout on the frictional pressure drop.

Syntheses and properties of associative acrylamide copolymers containing short hydrophobic chains used in a friction reducer for slick-water fracturing

Two allyldimethylalkyl quaternary ammonium salt(AQAS)monomers,N,N-dimethylallylphenylpropylammonium bromide(AQAS1)and N,N-dimethylallylnonylammonium bromide(AQAS2),were synthesized and used to prepare modified polyacrylamide materials.Two new drag reducers were synthesized from acrylamide(AM),sodium acrylate(Na AA)and a cationic modified monomer(AQAS1 or AQAS2)via aqueous solution polymerization,and the copolymers were named P(AM/Na AA/AQAS1)and P(AM/Na AA/AQAS2),respectively.The structures of the drag reduction agents were confirmed by IR and1H NMR spectroscopies.The molecular weight(Mw)of P(AM/Na AA/AQAS1)was 1.79×10^(6)g/mol.When the copolymer concentration was 1000 mg/L and the flow rate was 45 L/min,in fresh water the highest drag reduction rate was 75.8%,in 10,000 mg/L Na Cl solution the drag reduction rate decreased to 72.9%.The molecular weight of P(AM/Na AA/AQAS2)was 3.17×10^(6)g/mol.When the copolymer concentration was500 mg/L and the flow rate was 45 L/min,the drag reduction rate reached 75.2%,and in 10,000 mg/L Na Cl solution the drag reduction rate was 73.3%,decreased by approximately 1.9%.The drag reduction rate for partially hydrolyzed polyacrylamide(HPAM)was also investigated,and the results showed that the drag reduction rates for 500 and 1000 mg/L HPAM solutions were merely 43.2%and 49.0%in brine,respectively.Compared with HPAM,both of the above copolymers presented better drag reduction capacities.

Superhydrophobic melamine sponge prepared by radiation-induced grafting technology for efficient oil-water separation

This paper presents a superhydrophobic melamine(ME)sponge(ME-g-PLMA)prepared via high-energy radiation-induced in situ covalent grafting of long-alkyl-chain dodecyl methacrylate(LMA)onto an ME sponge for efficient oil–water separation.The obtained ME-g-PLMA sponge had an excellent pore structure with superhydrophobic(water contact angle of 154°)and superoleophilic properties.It can absorb various types of oils up to 66–168 times its mass.The ME-g-PLMA sponge can continuously separate oil slicks in water by connecting a pump or separating oil underwater with a gravity-driven device.In addition,it maintained its highly hydrophobic properties even after long-term immersion in different corrosive solutions and repeated oil adsorption.The modified ME-g-PLMA sponge exhibited excellent separation properties and potential for oil spill cleanup.

Bimetallic Single‑Atom Catalysts for Water Splitting

Green hydrogen from water splitting has emerged as a critical energy vector with the potential to spearhead the global transition to a fossil fuel-independent society.The field of catalysis has been revolutionized by single-atom catalysts(SACs),which exhibit unique and intricate interactions between atomically dispersed metal atoms and their supports.Recently,bimetallic SACs(bimSACs)have garnered significant attention for leveraging the synergistic functions of two metal ions coordinated on appropriately designed supports.BimSACs offer an avenue for rich metal–metal and metal–support cooperativity,potentially addressing current limitations of SACs in effectively furnishing transformations which involve synchronous proton–electron exchanges,substrate activation with reversible redox cycles,simultaneous multi-electron transfer,regulation of spin states,tuning of electronic properties,and cyclic transition states with low activation energies.This review aims to encapsulate the growing advancements in bimSACs,with an emphasis on their pivotal role in hydrogen generation via water splitting.We subsequently delve into advanced experimental methodologies for the elaborate characterization of SACs,elucidate their electronic properties,and discuss their local coordination environment.Overall,we present comprehensive discussion on the deployment of bimSACs in both hydrogen evolution reaction and oxygen evolution reaction,the two half-reactions of the water electrolysis process.

Measurement of Concentration of Sorbent Particles and Water Droplets in Hydration Desulfurization Reactor with PIV

Vortexing limestone injection into furnace combined with calcium lime hydration in the downstream is the most promising technology for controlling SO 2 emission. Particle imaging velocimetry (PIV) is used to measure the gas liquid solid three phase flow field in a reactor. By image processing based on newly developed software, the number concentrations of sorbent particles and water droplets are presented. The measuring results are very helpful for better understanding the desulfurization mechanism and optimizing configurational and operational parameters in the hydration reactor.

Evolution of a Water Pendant Droplet: Effect of Temperature and Relative Humidity

As part of a better understanding of drying liquids within porous materials, measurements from 293 to 343 K of deionized water surface tension in air as a function of relative humidity are exposed. Experimental work was carried out using the pendant drop method coupled with image analysis within an adapted instrumented climatic chamber. Results show that surface tension linearly decreases when relative humidity increases. Although the effect of humidity is less compared to that of the temperature and even less compared to a surfactant impact, it must not be neglected and values have to be mentioned when dealing with water evaporation. Modifying surface tension also affects the pendant drop shape. The drying kinetics of the pendant drop volume and its outer shell are connected to this change of shape. Steam in the air can be assimilated to a wetting agent, hence a surfactant, and can be used in an environmental-friendly way to ease the drying stage. Indeed, the challenge is to limit the risk of cracking and damaging pieces during this crucial step in material processing.

A Study of the Velocity Field during Evaporation of Sessile Water and Water/Ethanol Drops

Many studies have investigated evaporation of sessile drops in an attempt to understand the effect of wetting on theevaporation process.Recently interest has also increased in the deposition of particles from such drops,with evaporative massflux being deemed to be responsible for ring-like deposits,and counteraction of the mass flux by Marangoni convection explainingmore uniform deposition patterns.Understanding of such deposition processes is important in biological applications,such as the Litos test-system endorsed by the Russian Ministry of Health for diagnosis of urolithiasis and the evaporation ofcolloidal drops for depositing and organizing proteins and DNA.In most cases where deposition from evaporating drops hasbeen studied,velocity information is inferred from the final deposition pattern or from mathematical modeling based on simplifiedmodels of the physics of the evaporation process.In this study we have directly measured the flow velocities in the baseof sessile drops,using micro particle image velocimetry,viewing the drop from below,through the cover slide.For water drops,a radial pattern of flow was observed with a maximum velocity close to but not at the pinned outer edge.For ‘azeotropic’ethanol/water mixtures,the velocity field is more chaotic to begin with,passing through a phase involving three or four recirculationcells and finally having the same radial pattern as for water drops.

Calculation of watershed flow concentration based on the grid drop concept

The grid drop concept is introduced and used to develop a micromechanism-based methodology for calculating watershed flow concentration. The flow path and distance traveled by a grid drop to the outlet of the watershed are obtained using a digital elevation model （DEM）. Regarding the slope as an uneven carpet through which the grid drop passes, a formula for overland flow velocity differing from Manning＇s formula for stream flow as welt as Darcy＇s formula for pore flow is proposed. Compared with the commonly used unit hydrograph and isochronal methods, this new methodology has outstanding advantages in that it considers the influences of the slope velocity field and the heterogeneity of spatial distribution of rainfall on the flow concentration process, and includes only one parameter that needs to be calibrated. This method can also be effectively applied to the prediction of hydrologic processes in un-gauged basins.

Sensitivity of the Grid-point Atmospheric Model of IAP LASG(GAMILI.I.0)Climate Simulations to Cloud Droplet Effective Radius and Liquid Water Path

This paper documents a study to examine the sensitivity to cloud droplet effective radius and liquid water path and the alleviation the energy imbalance at the top of the atmosphere and at the surface in the latest version of the Grid-point Atmospheric Model of the State Key Laboratory of Numerical Modeling for Atmospheric Sciences and Geophysical Fluid Dynamics （LASG）, Institute of Atmospheric Physics （IAP） （GAMIL1.1.0）. Considerable negative biases in all flux components, and thus an energy imbalance, are found in GAMIL1.1.0. In order to alleviate the energy imbalance, two modifications, namely an increase in cloud droplet effective radius and a decrease in cloud liquid water path, have been made to the cloud properties used in GAMIL. With the increased cloud droplet effective radius, the single scattering albedo of clouds is reduced, and thus the reflection of solar radiation into space by clouds is reduced and the net solar radiation flux at the top of the atmosphere is increased. With the reduced cloud optical depth, the net surface shortwave radiation flux is increased, causing a net warming over the land surface. This results in an increase in both sensible and latent heat fluxes over the land regions, which is largely balanced by the increased terrestrial radiation fluxes. Consequently, the energy balance at the top of atmosphere and at the surface is achieved with energy flux components consistent with available satellite observations.

A study of the properties of hydrophobically associating water-soluble polymers used in drilling fluids

Hydrophobically associating water-soluble polymers (HPAP) have been synthesized from acrylamide(AM), acrylate (AA), 2-acrylamido-2-methyl propane sulfonic acid (AMPS) and hydrophobic monomer (AP) in aqueous solution by radical polymerization. New polymer drilling fluids are made up of HPAP, which is used as viscosifiers and encapsulation agents. Properties of this system are reported in this paper. Results indicate that this system has a high value of yield point to plastic viscosity (YP/PV≥0.7), high viscosity at a low-shear rate (LSRV≥30000mPa·s), excellent shear thinning behavior, good solid-carrying behavior, resistance to shear, good thermal stability (as high as 140℃) and salt resistance. The system has excellent behavior in high-density solution of NaCl and in calcium and magnesium rich saline solutions. Hence, HPAP also can be used in saltwater polymer drilling fluids.

Adhesion forces for water/oil droplet and bubble on coking coal surfaces with different roughness

Surface roughness plays a significant role in floatability of coal.In the present paper,coking coal surface was polished by three different sandpapers and the surface properties were characterized by contact angle and roughness measurements.The effect of surface roughness on floatability was investigated by adhesion force measurement system for measuring interaction forces between droplets/bubbles and coking coal surfaces with different roughness.The results showed that the contact angle decreased with increasing roughness yet the adhesion force between the water droplet and coal surface increased owing to the increased contact line and the appearance of line pinning.Maximum adhesion forces between water and surfaces were 111.70,125.48,and 136.42μN when the roughness was 0.23,0.98,and 2.79 μm,respectively.In contrast,under a liquid environment,the adhesion forces between air bubble/oil droplet and coal surfaces were decreased with increasing roughness because of the restriction by water.Maximum adhesion forces of increasing roughness were 97.14,42.76,and 17.86 μN measured at interfaces between air bubble and coal surfaces and 169.48,145.84,and 121.02 lN between oil droplet and surfaces,respectively.Decreasing roughness could be beneficial to the spreading of oil droplets and the adhesion of bubbles which is conducive to flotation separation.

Key techniques for evaluation of safety monitoring sensors in water conservancy and hydropower engineering

For the evaluation of construction quality and the verification of the design of water conservancy and hydropower engineering projects, and especially for the control of dam safety operation behavior, safety monitoring sensors are employed in a majority of engineering projects. These sensors are used to monitor the project during the dam construction and operation periods, and play an important role in reservoir safety operation and producing benefits. With the changing of operating environments and run-time of projects, there are some factors affecting the operation and management of projects, such as a certain amount of damaged sensors and instability of the measured data. Therefore, it is urgent to evaluate existing safety monitoring sensors in water conservancy and hydropower engineering projects. However, there are neither standards nor evaluation guidelines at present. Based on engineering practice, this study examined some key techniques for the evaluation of safety monitoring sensors, including the evaluation process of the safety monitoring system, on-site detection methods of two typical pieces of equipment, the differential resistor sensor and vibrating wire sensor, the on-site detection methods of communication cable faults, and a validity test of the sensor measured data. These key techniques were applied in the Xiaolangdi Water Control Project and Xiaoxi Hydropower Project. The results show that the measured data of a majority of sensors are reliable and reasonable, and can reasonably reflect the structural change behavior in the project operating process, indicating that the availabilities of the safety monitoring sensors of the two projects are high

Super-hydrophobic and super-lipophilic functionalized graphene oxide/polyurethane sponge applied for oil/water separation

Nowadays, oil spills have led to a serious environmental crisis of the world. To deal with this problem, inspired from super-hydrophobic lotus leaf, this study fabricated super-hydrophobic and super-lipophilic functionalized graphene oxide/polyurethane （FGP） sponge by a simple and inexpensive dip coating method. The resulting FGP sponge was characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and water contact angle. The results expressed that FGP sponge exhibited a similar surface structure to that of a lotus leaf, and possessed the super-hydrophobic characteristic with the water contact angle （WAC） of 152°± 1 °. The absorption capacity and reusability were also investigated. It can be seen that, the FGP sponge can remove a wide range of oils and organic solvents from water with good absorption capacities （up to 35 times of its own mass）. Significantly, after 10 cycles the absorption capacity of the oils and organic solvents was higher than 90°; for the reused FGP sponge, demonstrating the good reusability of the FGP sponge. Therefore, this study probably provided a simole way to remove the pollutions ofoil spills and toxic organism from water.

Underwater gas self-transportation along femtosecond laser-written open superhydrophobic surface microchannels(<100μm)for bubble/gas manipulation

Underwater transportation of bubbles and gases has essential applications in manipulating and using gas,but achieving this function at the microscopic level remains a significant challenge.Here,we report a strategy to self-transport gas in water along a laser-induced open superhydrophobic microchannel with a width less than 100μm.The femtosecond laser can directly write superhydrophobic and underwater superaerophilic microgrooves on the polytetrafluoroethylene(PTFE)surfaces.In water,the single laser-induced microgroove and water medium generate a hollow microchannel.When the microchannel connects two superhydrophobic regions in water,the gas spontaneously travels from the small region to the large area along this hollow microchannel.Gas self-transportation can be extended to laser-drilled microholes through a thin PTFE sheet,which can even achieve anti-buoyancy unidirectional penetration.The gas can overcome the bubble’s buoyance and spontaneously travel downward.The Laplace pressure difference drives the processes of spontaneous gas transportation and unidirectional bubble passage.We believe the property of gas self-transportation in the femtosecond laser-structured open superhydrophobic and underwater superaerophilic microgrooves/microholes has significant potential applications related to manipulating underwater gas.

Effect of water droplet in solvent sublation

Aqueous phase layer around bubble and water droplet are two additional processes in solvent sublation. In the dynamic process of mass transfer, they are always neglected, but they are very important in the investigation of thermodynamic equilibrium. In this paper, the effect of water droplet in solvent sublation was discussed in detail, and the previous mathematical model of solvent subaltion was improved. Matlab 6.5 was used to simulate the process of water droplets, and the comparison between the previous hypothesis and the improvement in this paper showed the superiority, especially in the investigation of thermodynamic equilibrium. Moreover, the separation and concentration of the complex compound dithizone-Co（Ⅱ） from aqueous phase to n-octanol by solvent sublation also proved the improved mathematical model was reasonable.

Direct transition of potential of water droplets to electric energy using aligned single-walled carbon nanotubes

In this paper, we report that an electromotive force （EMF） can be induced in a rope of aligned single-walled carbon nanotubes （SWNTs） when water droplets fall on this rope. The magnitude of this EMF depends sensitively on the slant angle of the SWNTs. Most interestingly, both the magnitude and the direction of the induced EFM can be modulated by applying a current to the SWNTs. The concepts of electrical slip and no-slip are proposed and can be quantitatively described by ＂electrical slip resistance＂. This kind of generator does not need any magnet, rotor, etc and shows quite a different operating mechanism and design compared with a conventional large scale hydroelectric power generator.

Numerical Simulation of Water Droplets Deposition on the Last-Stage Stationary Blade of Steam Turbine

Based on the method of discrete phase, the law of droplets’ deposition in the last stage stationary blade of a supercritical 600 MW Steam Turbine is simulated in the first place of this paper by using the Wet-steam model in commercial software FLUENT, where the influence of inlet angle of water droplets of the stationary blades is also considered. Through the calculation, the relationship between the deposition and the diameter of water droplets is revealed. Then, the amount of droplets deposition in the suction and pressure surface is derived. The result is compared with experimental data and it proves that the numerical simulation result obtained in this paper is reasonable. Finally, a formula of the relationship between the diameter of water droplets and the inlet angle is fit, which could be used for approximate calculation in the engineering applications.

Electrostatic Enhancement of Coalescence of Oil Droplets(in Nanometer Scale) in Water Emulsion

Oil droplets in nanometer scale which are dispersed in water cannot be separated easily. An attractive technique is carried out by electrical phenomena to demulsify oil in water emulsion. In this research, non-uniform electric field or dielectrophoresis （DEP） is applied to remove sunflower oil （which is dispersed in the water）. Effectsof temperature, time and voltage （using AC-electric field） were considered to get the highest DEP-force （Fdi） and the best results. The oil particles sizes with average of approximately 76 nm have been shown using a ZetaSizer Nano ZS, Model ZEN 1600 （Malvem Instrument Ltd.）. The maximum separation efficiency of 85% is obtained at the optimum temperature of 38 ℃ and voltage of 3000 V.

Spreading of a Multicomponent Drop in Water: Solutions and Suspensions

The distribution of material resulting from the impact of a freely falling drop with a target liquid has been studied by photo and video registration methods.Different cases have been investigated by considering drops made of aqueous solutions(ink,salt,acid)and including fine solid particles(i.e.,suspensions).New features have been observed in terms of flow dynamics and thin components produced as a result of the impact(such as banded elements,ligaments,and vortices at the surface of the liquid).In particular,the characteristics of emerging netlike structures have been found to depend on the size of the suspension clusters.For the case of acetic acid,a different patterning behavior has been obtained:sequences of concentric arcs are produced in that case.However,linear scaling laws and the discrete nature of the distribution of the droplet material seem to be features common to all the cases considered.