Four-channel catalytic micro-reactor based on alumina hollow fiber membrane for efficient catalytic oxidation of CO

The traditional automotive catalytic converter using commercial ceramic honeycomb carriers has many problems such as high back pressure,low engine efficiency,and high usage of precious metals.This study proposes a four-channel catalytic micro-reactor based on alumina hollow fiber membrane,which uses phase inversion method for structural molding and regulation.Due to the advantages of its carrier,it can achieve lower ignition temperature under low noble metal loading.With Pd/CeO_(2) at a loading rate of 2.3%(mass),the result showed that the reaction ignition temperature is even less than 160℃,which is more than 90℃ lower than the data of commercial ceramic substrates under similar catalyst loading and airspeed conditions.The technology in turn significantly reduces the energy consumption of the reaction.And stability tests were conducted under constant conditions for 1000 h,which proved that this catalytic converter has high catalytic efficiency and stability,providing prospects for the design of innovative catalytic converters in the future.

Comparative structural and electrochemical properties of mixed P2/O′3-layered sodium nickel manganese oxide prepared by sol-gel and electrospinning methods:Effect of Na-excess content

The effect of Na-excess content in the precursor on the structural and electrochemical performances of sodium nickel manganese oxide(NNMO)prepared by sol-gel and electrospinning methods is investigated in this paper.X-ray diffraction results of the prepared NNMO without adding Na-excess content indicate sodium loss,while the mixed phase of P2/O′3-type layered NNMO presented after adding Na-excess content.Compared with the sol-gel method,the secondary phase of NiO is more suppressed by using the electrospinning method,which is further confirmed by field emission scanning electron microscope images.N_(2) adsorption-desorption isotherms show no remarkably difference in specific surface areas between different preparation methods and Na-excess contents.The analysis of X-ray absorption near edge structure indicates that the oxidation states of Ni and Mn are+2 and+4,respectively.For the electrochemical properties,superior electrochemical performance is observed in the NNMO electrode with a low Na-excess content of 5wt%.The highest specific capacitance is 36.07 F·g^(-1)at0.1 A·g^(-1)in the NNMO electrode prepared by using the sol-gel method.By contrast,the NNMO electrode prepared using the electrospinning method with decreased Na-excess content shows excellent cycling stability of 100%after charge-discharge measurements for 300 cycles.Therefore,controlling the Na excess in the precursor together with the preparation method is important for improving the electrochemical performance of Na-based electrode materials in supercapacitors.

Influence of preparation methods on CuO-CeO_2 catalysts in the preferential oxidation of CO in excess hydrogen

Influence of three different preparation methods, i.e. impregnation, coprecipitation, and inverse coprecipitation, on the preferential oxidation of CO in excess hydrogen （PROX） over CuO-CeO2 catalysts has been investigated and CuO-CeO2 catalysts are characterized using BET, XPS, XRD, UV Raman, and TPR techniques. The results show that the catalysts prepared by coprecipitation have smaller particle sizes, well-dispersed CuOx species, more oxygen vacancies, and are more active in the PROX than those prepared by the other methods. However. the inverse coprecipitation depresses the catalytic performance of CuO-CeO2 catalysts and causes the growth of CuO-CeO2 because of different pH value in the precipitation process.

Effect of pretreatment methods on the performance of Cu-Zr-Ce-O catalyst for CO selective oxidation

The Cu-Zr-Ce-O catalysts prepared using the coprecipitation method exhibited better catalytic performance for CO selective oxidation. The Cu-Zr-Ce-O catalysts pretreated with different methods were studied by CO-TPR and XPS techniques. The results showed that the Cu-Zr-Ce-O catalyst pretreated with oxygen exhibited the best catalytic performance and had the widest operating temperature window, with CO conversion above 99% from 160 to 200 ℃. The O2 pretreatment caused an enrichment of the oxygen storaged on the Cu active species and promoted the conversion of adsorbed oxygen into surface lattice oxygen. It also improved the amount of Cu＋/Cu^2＋ ionic pair, and then facilitated the formation of CuO active species on the catalyst for selective CO oxidation.

Preferential Oxidation of CO in Excess Hydrogen over CuO-CeO_2 Catalyst Prepared by Chelating Method

The CuO-CeO2 catalyst prepared by chelating method has a superior catalytic performance for the preferential oxidation of CO in rich hydrogen, compared with the CuO-CeO2 catalyst prepared by coprecipitation method. The CO conversions over these catalysts, at 120 ℃ and 120000 ml/（g-h） in the absence of CO2 and H2O, are 99.6% and 88.6%, respectively, and the selectivity of O2 over these catalysts is very close （i.e. 51.3% and 55.8%, respectively）. The influence of certain factors such as hydrogen concentration, carbon monoxide concentration, H2O, O2/CO ratios, and space velocity on the catalytic performance of CuO-CeO2 catalyst prepared by chelating method is also studied. The results show that the addition of hydrogen and H2O has a negative effect on the catalytic performance of CuO-CeO2 catalyst, however, the variation of space velocity and the O2/CO ratio causes a comparatively slight influence.

Analysis on high-temperature oxidation and growth stress of iron-based alloy using phase field method

High-temperature oxidation is an important property to evaluate thermal protection materials. However, since oxidation is a complex process involving microstructure evolution, its quantitative analysis has always been a challenge. In this work, a phase field method （PFM） based on the thermodynamics theory is developed to simulate the oxidation behavior and oxidation induced growth stress. It involves microstructure evolution and solves the problem of quantitatively computational analysis for the oxidation behavior and growth stress. Employing this method, the diffusion process, oxidation performance, and stress evolution axe predicted for Fe-Cr-A1-Y alloys. The numerical results agree well with the experimental data. The linear relationship between the maximum growth stress and the environment oxygen concentration is found. PFM provides a powerful tool to investigate high-temperature oxidation in complex environments.

Lipid Oxidation of Catfish (<i>Arius maculatus</i>) after Cooking and Smoking by Different Methods Applied in Cameroon

The influence of different cooking and smoking methods (boiling, frying, frying + boiling, hot and cold smoking) on oxidation and fatty acid composition of catfish (Arius maculatus) commercialized on the Wouri river coast was evaluated including commonly used analytical indexes (peroxide and acid values)and physical analysis by Fourier transform infrared (FTIR) spectroscopy. The mean moisture, protein, ash and fat contents of raw fish were 75.88 ± 0.55;64.24 ± 0.14;10.98 ± 0.31 and 23.02 ± 0.88 respectively. All these treatments provoke the modification of the quality indexes. Lipid deterioration, thermolysis and lipid oxidation occurred throughout the treatment. Peroxide value decreased for all cooked and smoked catfish, while free fatty acids of smoked sample increased. The FTIR applied to evaluate lipid oxidation in extracted lipid clearly provided a better picture of the oxidation progress and led to a similar conclusion with chemical analysis. Boiled, bleaching hot and bleaching cold smoking were found to be the suitable treatment methods for catfish because they gave it a high nutritive value compared to other smoking methods.

Oil oxidation in the whole temperature regions during oil reservoir air injection and development methods

The oil oxidation characteristics of the whole temperature regions from 30 ℃ to 600 ℃ during oil reservoir air injection were revealed by experiments. The whole oil oxidation temperature regions were divided into four different parts: dissolving and inflation region, low temperature oxidation region, medium temperature oxidation region and high temperature oxidation region. The reaction mechanisms of different regions were explained. Based on the oil oxidation characteristics and filed tests results, light oil reservoirs air injection development methods were divided into two types: oxygen-reducing air flooding and air flooding;heavy oil reservoirs air injection in-situ combustion development methods were divided into two types: medium temperature in-situ combustion and high temperature in-situ combustion. When the reservoir temperature is lower than 120 ℃, oxygen-reducing air flooding should be used for light oil reservoir development. When the reservoir temperature is higher than 120 ℃, air flooding method should be used for light oil reservoir development. For a normal heavy oil reservoir, when the combustion front temperature is lower than 400 ℃, the development method is medium temperature in-situ combustion. For a heavy oil reservoir with high oil resin and asphalting contents, when the combustion front temperature is higher than 450 ℃, the development method at this condition is high temperature in-situ combustion. Ten years field tests of air injection carried out by PetroChina proved that air has advantages in technical, economical and gas source aspects compared with other gas agents for oilfield gas injection development. Air injection development can be used in low/super-low permeability light oil reservoirs, medium and high permeability light oil reservoirs and heavy oil reservoirs. Air is a very promising gas flooding agent.

Phase composition,conductivity,and sensor properties of cerium-doped indium oxide

The hydrothermal synthesis of In_(2)O_(3)and CeO_(2)–In_(2)O_(3)is investigated as well as the properties of sensor layers based on these compounds.During the synthesis of In_(2)O_(3),intermediate products In(OH)_(3)and InOOH are formed,which are the precursors of stable cubic(c-In_(2)O_(3))and metastable rhombohedral(rh-In_(2)O_(3))phases,respectively.A transition from c-In_(2)O_(3)to rh-In_(2)O_(3)is observed with the addition of CeO_(2).The introduction of cerium into rh-In_(2)O_(3)results in a decrease in the sensor response to hydrogen,while it increases in composites based on c-In_(2)O_(3).The data on the sensor activity of the composites correlate with XPS results in which CeO_(2)causes a decrease in the concentrations of chemisorbed oxygen and oxygen vacancies in rh-In_(2)O_(3).The reverse situation is observed in composites based on c-In_(2)O_(3).Compared to In_(2)O_(3)and CeO_(2)–In_(2)O_(3)obtained by other methods,the synthesized composites demonstrate maximum response to H_(2)at low temperatures by 70–100℃,and have short response time(0.2–0.5 s),short recovery time(6–7 s),and long-term stability.A model is proposed for the dependence of sensitivity on the direction of electron transfer between In_(2)O_(3)and CeO_(2).

Study on Industrial Application of Hydrogen Sulfide Removal by Wet Oxidation Method with High Gravity Technology

The removal of hydrogen sulfide from gas plays an important role in rational utilization of resources and environ- mental protection. In this paper, the process of hydrogen sulfide removal by wet oxidation method in a rotating packed bed was investigated in a scale for treating 10 000 Nm3/h of gas. On the basis of studying the influence of the species and con- centration of alkali source, the liquid/gas volume ratio, the high gravity factor, and the hydrogen sulfide content in feed gas on the desulfurization effect, the suitable technological conditions were obtained. The hydrogen sulfide removal efficiency could reach 98.0% under these conditions. The results of continuous operation of process facilities showed that the high gravity method has many merits including higher desulfurization rate, good stability in operation, lower liquid/gas volume ratio, greater operation elasticity, and apparent energy saving effects.

Lattice Boltzmann simulation study of anode degradation in solid oxide fuel cells during the initial aging process

For present solid oxide fuel cells(SOFCs),rapid performance degradation is observed in the initial aging process,and the dis-cussion of the degradation mechanism necessitates quantitative analysis.Herein,focused ion beam-scanning electron microscopy was em-ployed to characterize and reconstruct the ceramic microstructures of SOFC anodes.The lattice Boltzmann method(LBM)simulation of multiphysical and electrochemical processes in the reconstructed models was performed.Two samples collected from industrial-size cells were characterized,including a reduced reference cell and a cell with an initial aging process.Statistical parameters of the reconstructed microstructures revealed a significant decrease in the active triple-phase boundary and Ni connectivity in the aged cell compared with the reference cell.The LBM simulation revealed that activity degradation is dominant compared with microstructural degradation during the initial aging process,and the electrochemical reactions spread to the support layer in the aged cell.The microstructural and activity de-gradations are attributed to Ni migration and coarsening.

Systematic Method for Constructing Lewis Representations

The systematic method for constructing Lewis representations is a method for representing chemical bonds between atoms in a molecule. It uses symbols to represent the valence electrons of the atoms involved in the bond. Using a number of rules in a defined order, it is often better suited to complicated cases than the Lewis representation of atoms. This method allows us to determine the formal charge and oxidation number of each atom in the edifice more efficiently than other methods.

A review of ^(17)O isotopic labeling techniques for solid-state NMR structural studies of metal oxides in lithium-ion batteries

Recent advances in utilizing ^(17)O isotopic labeling methods for solid-state nuclear magnetic resonance(NMR)investigations of metal oxides for lithium-ion batteries have yielded extensive insights into their structural and dynamic details.Herein,we commence with a brief introduction to recent research on lithium-ion battery oxide materials studied using ^(17)O solid-state NMR spectroscopy.Then we delve into a review of ^(17)O isotopic labeling methods for tagging oxygen sites in both the bulk and surfaces of metal oxides.At last,the unresolved problems and the future research directions for advancing the ^(17)O labeling technique are discussed.

Preparation of Rare Earth Hydroxide and Oxide Nanoparticles by Precipitation Method

A series of rare earth hydroxide and oxide nanoparticles have been prepared by precipitation method with alcohol as the dispersive and protective reagent. Transmission electron microscope （TEM） images indicate that the particles are spherical in shape and smaller than 100 nm in size. The crystallite sizes of cubic Ln2O3 have lanthanide shrinking effect, while average crystal lattice distortion rates possess lanthanide swelling effect. The diffraction peak intensity of heavy rare earth oxide nanometer powders is remarkably stronger than that of light rare earth oxide nanometer powders. The variation of diffraction intensity with atomic number presents an inverted W type, forming a double peak structure. Fourier transform infrared （FTIR） spectrums reveal that Ln2O3 nanopowders have higher surface activity than that of ordinary Ln2O3 powders. The UV-vis spectra show that Ln-O bond of these particles is slightly blue-shifted, and its absorption intensity decreases.

Preparation of Ultrafine and High Dispersion Pd/C Catalyst and Its Electrocatalytic Performance for Formic Acid Oxidation

A carbon supported Pd（Pd/C） catalyst used as the anodic catalyst in the direct formic acid fuel cells（DFAFC） was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate（EDTA） as stabilizer and complexing agent. This method is very simple. The average size of the Pd particles in the Pd/C catalyst prepared with the improved complex reduction method is as small as about 2.1 nm and the Pd particles in the Pd/C catalyst possess an excellent uniformity. The Pd/C catalyst shows a high electrocatalytic activity and stability for the formic acid oxidation.

Extracting reaction mechanism analysis of Zn and Si from zinc oxide ore by NaOH roasting method

The orthogonal test was used to optimize the reaction conditions of roasting zinc oxide ore with NaOH aiming to comprehensively utilize zinc oxide ore.The optimized reaction conditions were molar ratio of NaOH to zinc oxide ore 6:1,roasting temperature 450°C,holding time 150 min.The molar ratio of NaOH to zinc oxide ore was the most predominant factor affecting the extraction ratios of zinc oxide and silica.The mineral phase transformations were investigated by testing the phases of specimens obtained at different temperatures.The process was that silica reacted with molten NaOH to form Na_2SiO_3 at first,then transformed into Na_4SiO_4 with temperature rising.ZnCO_3 and its decomposing product ZnO reacted with NaOH to form Na_2ZnO_2.Na_2ZnSiO_4was also obtained.The reaction rate was investigated using unreacted shrinking core model.Two models used were chemical reaction at the particle surface and diffusion through the product layer.The results indicated that the reaction rate was combine-controlled by two models.The activation energy and frequency factor were obtained as 24.12 k J/mol and 0.0682,respectively.

Low-temperature synthesis of nitrogen doped carbon nanotubes as promising catalyst support for methanol oxidation

The electrochemical methanol oxidation reaction(MOR) is of paramount importance for direct methanol fuel cell(DMFC) application, where efficient catalysts are required to facilitate the complicated multiple charge transfer process. The catalyst support not only determines the dispersion status of the catalysts particles, but also exerts great influence on the electronic structure of the catalysts, thereby altering its intrinsic activity. Herein, we demonstrated that nitrogen atoms, assisted by the pre-treatment of carbon matrix with oxidants, can be easily doped into carbon nanotubes at low temperature. The obtained nitrogen-doped carbon nanotubes can effectively improve the dispersion of the supported platinum nanoparticles and facilitate the MOR by modifying the electronic structure of platinum atoms,through catalyst-support interaction.

Selective oxidation of methane to formaldehyde by oxygen over silica-supported iron catalysts

FeOx-SiO2 catalysts prepared by a sol-gel method were studied for the selective oxidation of methane by oxygen. A single-pass formaldehyde yield of 2.0% was obtained over the FeOx-SiO2 with an iron content of 0.5 wt% at 898 K. This 0.5 wt% FeOx-SiO2 catalyst demonstrated significantly higher catalytic performances than the 0.5 wt% FeOx/SiO2 prepared by an impregnation method. The correlation between the catalytic performances and the characterizations with UV-Vis and H2-TPR suggested that the higher dispersion of iron species in the catalyst prepared by the sol-gel method was responsible for its higher catalytic activity for formaldehyde formation. The modification of the FeOx-SiO2 by phosphorus enhanced the formaldehyde selectivity, and a single-pass formaldehyde yield of 2.4% could be attained over a P-FeOx-SiO2 catalyst （P/Fe = 0.5） at 898 K. Raman spectroscopic measurements indicated the formation of FePO4 nanoclusters in this catalyst, which were more selective toward formaldehyde formation.

Annealing temperature dependent catalytic water oxidation activity of iron oxyhydroxide thin films

Nanostructured iron oxyhydroxide（Fe OOH） thin films have been synthesized using an electrodeposition method on a nickel foam（NF） substrate and effect of air annealing temperature on the catalytic performance is studied. The as-deposited and annealed thin films were characterized by X-ray diffraction（XRD）,X-ray photoelectron spectroscopy（XPS）, field emission scanning electron microscopy（FE-SEM） and linear sweep voltammetry（LSV） to determine their structural, morphological, compositional and electrochemical properties, respectively. The as-deposited nanostructured amorphous Fe OOH thin film is converted into a polycrystalline Fe;O;with hematite crystal structure at a high temperature. The Fe OOH thin film acts as an efficient electrocatalyst for the oxygen evolution reaction（OER） in an alkaline 1 M KOH electrolyte. The film annealed at 200 °C shows high catalytic activity with an onset overpotential of 240 m V with a smaller Tafel slope of 48 m V/dec. Additionally, it needs an overpotential of 290 mV to the drive the current density of 10 m A/cm;and shows good stability in the 1 M KOH electrolyte solution.

Effect of Bi promoter on the performances of selective oxidation of isobutane to methacrolein over MoVO/AlPO_4 catalysts

The effects of Bi on the catalytic performance of selective oxidation of isobutane to methacrolein over MoVO/AlPO4 catalyst were investigated by XRD, FT-Raman, XPS, UV-vis DRS techniques. The results show that the addition of Bi component into the MoVO/AlPO4 catalyst obviously improves the catalytic performance, and the selectivity to methacrolein can increase from 14.2% to 45.1% with the increase of Bi/V molar ratio from 0 to 1. Combining the characterization results with the reaction evaluation, it is concluded that the catalytic activities of the MoV0.3Bix/AlPO4 catalysts are related to the crystalline phase composition and the dispersion of molybdenum and vanadium oxides species in general, and also to the V5＋/V4＋ molar ratio on the surface in particular.