A triboelectric nanogenerator based on a spiral rotating shaft for efficient marine energy harvesting of the hydrostatic pressure differential

Equipment used in underwater sensing and exploration typically relies on cables or batteries for energy supply,resulting in a limited and inconvenient energy supply and marine environmental pollution that hinder the sustainable development of distributed ocean sensing networks.Here,we design a deep-sea differential-pressure triboelectric nanogenerator(DP-TENG)based on a spiral shaft drive using modified polymer materials to harness the hydrostatic pressure gradient energy at varying ocean depths to power underwater equipment.The spiral shaft structure converts a single compression into multiple rotations of the TENG rotor,achieving efficient conversion of differential pressure energy.The multi-pair electrode design enables the DP-TENG to generate a peak current of 61.7μA,the instantaneous current density can reach 0.69μA cm^(-2),and the output performance can be improved by optimizing the spiral angle of the shaft.The DP-TENG can charge a 33μF capacitor to 17.5 V within five working cycles.It can also power a digital calculator and light up 116 commercial power light-emitting diodes,demonstrating excellent output capability.With its simple structure,low production cost,and small form factor,the DP-TENG can be seamlessly integrated with underwater vehicles.The results hold broad prospects for underwater blue energy harvesting and are expected to contribute to the development of self-powered equipment toward emerging“smart ocean”and blue economy applications.

Ultra-broadband microwave absorber and high-performance pressure sensor based on aramid nanofiber,polypyrrole and nickel porous aerogel

Electronic devices have become ubiquitous in our daily lives,leading to a surge in the use of microwave absorbers and wearable sensor devices across various sectors.A prime example of this trend is the aramid nanofibers/polypyrrole/nickel(APN)aerogels,which serve dual roles as both microwave absorbers and pressure sensors.In this work,we focused on the preparation of aramid nanofibers/polypyrrole(AP15)aerogels,where the mass ratio of aramid nanofibers to pyrrole was 1:5.We employed the oxidative polymerization method for the preparation process.Following this,nickel was thermally evaporated onto the surface of the AP15 aerogels,resulting in the creation of an ultralight(9.35 mg·cm^(-3)).This aerogel exhibited a porous structure.The introduction of nickel into the aerogel aimed to enhance magnetic loss and adjust impedance matching,thereby improving electromagnetic wave absorption performance.The minimum reflection loss value achieved was-48.7 dB,and the maximum effective absorption bandwidth spanned 8.42 GHz with a thickness of 2.9 mm.These impressive metrics can be attributed to the three-dimensional network porous structure of the aerogel and perfect impedance matching.Moreover,the use of aramid nanofibers and a three-dimensional hole structure endowed the APN aerogels with good insulation,flame-retardant properties,and compression resilience.Even under a compression strain of 50%,the aerogel maintained its resilience over 500 cycles.The incorporation of polypyrrole and nickel particles further enhanced the conductivity of the aerogel.Consequently,the final APN aerogel sensor demonstrated high sensitivity(10.78 kPa-1)and thermal stability.In conclusion,the APN aerogels hold significant promise as ultra-broadband microwave absorbers and pressure sensors.

Test and Study of the Rock Pressure Sensitivity for KeLa-2 Gas Reservoir in the Tarim Basin

KeLa-2 gas reservoir is the largest uncompartimentalized gas field so far discovered in China, with a reserve of hundreds of billions of cubic meters of dry gas. It has such features as extremely long interval (550m), high pressure (74.5MPa) and pressure coefficient (2.022). Gas reservoirs with a pressure coefficient of over 2.0 are not commonly found. The abnormal high-pressure reservoirs are quite different in characteristic and performance during the process of depletion exploitation. Therefore, it is necessary to know the property of pressure sensitivity for this abnormal high-pressure reservoir. The aim of this paper is to test the reservoir pressure sensitivity and to analyze its effect on the deliverability of gas. Through some experiments, the permeability change with the confining pressure of rock samples from KeLa-2 abnormal high-pressure gas reservoir is measured. A power function is used to match the measured data, and to derive an empirical equation to describe the change of permeability through the change of the reservoir pressure or effective overburden pressure. Considering the permeability change during the development of reservoirs, a conventional deliverability equation is modified, and the deliverability curve for KeLa-2 gas reservoir is predicted. The research indicates that the extent of the pressure sensitivity of rock samples from KeLa-2 is higher than that from the Daqing oilfield. KeLa-2 reservoir rock has the feature of an undercompaction state. The pressure sensitivity of a reservoir may decrease the well deliverability. It is concluded that for KeLa-2 reservoir the predicted absolute open flow (AOF), when the pressure sensitivity is taken into account, is approximately 70% of the AOF when permeability is constant and does not change with pressure.

Bioinspired flexible piezoresistive sensor for high-sensitivity detection of broad pressure range

The human skin has the ability to sense tactile touch and a great range of pressures.Therefore,in prosthetic or robotic systems,it is necessary to prepare pressure sensors with high sensitivity in a wide measurement range to provide human-like tactile sensation.Herein,we developed a flexible piezoresistive pressure sensor that is highly sensitive in a broad pressure range by using lotus leaf micropatterned polydimethylsiloxane and multilayer superposition.By superposing four layers of micropatterned constructive substrates,the multilayer piezoresistive pressure sensor achieves a broad pressure range of 312 kPa,a high sensitivity of 2.525 kPa^(−1),a low limit of detection(LOD)of<12 Pa,and a fast response time of 45 ms.Compared with the traditional flexible pressure sensor,the pressure range of this sensor can be increased by at least an order of magnitude.The flexible piezoresistive pressure sensor also shows high robustness:after testing for at least 1000 cycles,it shows no sign of fatigue.More importantly,these sensors can be potentially applied in various human motion detection scenarios,including tiny pulse monitoring,throat vibration detection,and large under-feet pressure sensing.The proposed fabrication strategy may guide the design of other kinds of multifunctional sensors to improve the detection performance.

Advancing the pressure sensing performance of conductive CNT/PDMS composite film by constructing a hierarchical-structured surface

Flexible pressure sensors have attracted wide attention due to their applications to electronic skin,health monitoring,and human-machine interaction.However,the tradeoff between their high sensitivity and wide response range remains a challenge.Inspired by human skin,we select commercial silicon carbide sandpaper as a template to fabricate carbon nanotube(CNT)/polydimethylsiloxane(PDMS)composite film with a hierarchical structured surface(h-CNT/PDMS)through solution blending and blade coating and then assemble the h-CNT/PDMS composite film with interdigitated electrodes and polyurethane(PU)scotch tape to obtain an h-CNT/PDMS-based flexible pressure sensor.Based on in-situ optical images and finite element analysis,the significant compressive contact effect between the hierarchical structured surface of h-CNT/PDMS and the interdigitated electrode leads to enhanced pressure sensitivity and a wider response range(0.1661 kPa^(-1),0.4574 kPa^(-1)and 0.0989 kPa^(-1)in the pressure range of 0–18 kPa,18–133 kPa and 133–300 kPa)compared with planar CNT/PDMS composite film(0.0066 kPa^(-1)in the pressure range of 0–240 kPa).The prepared pressure sensor displays rapid response/recovery time,excellent stability,durability,and stable response to different loading modes(bending and torsion).In addition,our pressure sensor can be utilized to accurately monitor and discriminate various stimuli ranging from human motions to pressure magnitude and spatial distribution.This study supplies important guidance for the fabrication of flexible pressure sensors with superior sensing performance in next-generation wearable electronic devices.

Soil Pressure Mini-sensor Made of Monocrystalline Silicon and the Measurement of Its Sensitivity Coefficient

A calibration test was done in order to measure its sensitivity coefficient by an improved soil test device.The experimental result shows that the soil pressure min-sensor made of the monocrystalline silicon（SPMMS）is proved to be good linear,high precision and less that can fetch precise data in low pressure range even near by O point,which guarantees the reliability of the soil pressure test in geotechnical engineering.

Accumulation and exploration enlightenment of shallow normal-pressure shale gas in southeastern Sichuan Basin, SW China

Based on the drilling, logging, experimental and testing data of Well PD1, a shallow normal-pressure shale gas well in the Laochangping anticline in southeastern Sichuan Basin, the shallow shale gas reservoirs of the Ordovician Wufeng Formation to Silurian Longmaxi Formation (Wufeng-Longmaxi) were investigated in terms of geological characteristics, occurrence mechanism, and adsorption-desorption characteristics, to reveal the enrichment laws and high-yield mechanism of shallow normal-pressure shale gas in complex structure areas. First, the shallow shale gas reservoirs are similar to the medium-deep shale gas reservoirs in static indicators such as high-quality shale thickness, geochemistry, physical properties and mineral composition, but the former is geologically characterized by low formation pressure coefficient, low gas content, high proportion of adsorbed gas, low in-situ stress, and big difference between principal stresses. Second, shallow shales in the complex structure areas have the gas occurrence characteristics including low total gas content (1.1-4.8 m3/t), high adsorbed gas content (2.5-2.8 m3/t), low sensitive desorption pressure (1.7-2.5 MPa), and good self-sealing. Third, the adsorbed gas enrichment of shales is mainly controlled by organic matter abundance, formation temperature and formation pressure: the higher the organic matter abundance and formation pressure, the lower the formation temperature and the higher the adsorption capacity, which is more beneficial for the adsorbed gas occurrence. Fourth, the shallow normal-pressure shale gas corresponds to low sensitive desorption pressure. The adsorbed gas can be rapidly desorbed and recovered when the flowing pressure is reduced below the sensitive desorption pressure. Fifth, the exploration breakthrough of Well PD1 demonstrates that the shallow complex structure areas with adsorbed gas in dominance can form large-scale shale reservoirs, and confirms the good exploration potential of shallow normal-pressure shale gas in the margin of the Sichuan Basin.

Application and analysis of functionally graded piezoelectrical rotating cylinder as mechanical sensor subjected to pressure and thermal loads

The exact thermoelastic analysis of a functionally graded piezoelectrical （FGP） rotating cylinder is investigated analytically. The cylinder is subjected to a com- bination of electrical, thermal, and mechanical loads simultaneously. The structure is a simplified model of a rotational sensor or actuator. The basic governing differential equation of the system is obtained by using the energy method. A novel term, named as the additional energy, is introduced to exact the evaluation of the energy functional. The solution to the governing differential equation is presented for two types of boundary conditions including free rotating and rotating cylinders exposed to the inner pressure. The effect of the angular velocity is investigated on the radial distribution of various components. The mentioned structure can be considered as a sensor for measuring the angular velocity of the cylinder subjected to the pressure and temperature. The obtained results indicate that the electrical potential is proportional to the angular velocity.

State-of-the-art and recent developments in micro/nanoscale pressure sensors for smart wearable devices and health monitoring systems

Small-sized,low-cost,and high-sensitivity sensors are required for pressure-sensing applications because of their critical role in consumer electronics,automotive applications,and industrial environments.Thus,micro/nanoscale pressure sensors based on micro/nanofabrication and micro/nanoelectromechanical system technologies have emerged as a promising class of pressure sensors on account of their remarkable miniaturization and performance.These sensors have recently been developed to feature multifunctionality and applicability to novel scenarios,such as smart wearable devices and health monitoring systems.In this review,we summarize the major sensing principles used in micro/nanoscale pressure sensors and discuss recent progress in the development of four major categories of these sensors,namely,novel material-based,flexible,implantable,and selfpowered pressure sensors.

Mechanical and electronic approaches to improve the sensitivity of microcantilever sensors

Advances in the field of micro electro mechanical systems and their uses now offer unique opportunities in the design of ultrasensitive analytical tools. The analytical community continues to search for cost-effective, reliable, and even portable analytical techniques that can give reliable and fast response results for a variety of chemicals and biomolecules. Microcantilevers （MCLs） have emerged as a unique platform for label-free chem-sensor or bioassay. Several electronic designs, including piezoresistive, piezoelectric, and capacitive approaches, have been applied to measure the bending or frequency change of the MCLs upon exposure to chemicals. This review summarizes mechanical, fabrication, and electronics approaches to increase the sensitivity of MCL sensors.

On the Temperature Profile of the Thermally Excited Resonant Silicon Micro Structural Pressure Sensor

According to the sensing structure of a practical silicon resonant pressure micro sensor whose preliminary sensing unit is a square silicon diaphragm and the final sensing unit is a silicon beam resonator, its operating mechanism is analyzed. The thermal resistor acts as the excited unit, and the piezoresistive unit acts as the detector, for the above micro sensor. By using the amplitude and phase conditions, the self exciting closed loop system is investigated based on the operating mechanism for the abov...

Experimental Measurements of the Sensitivity of Fiber-optic Bragg Grating Sensors with a Soft Polymeric Coating under Mechanical Loading,Thermal and Magnetic under Cryogenic Conditions

The strain and temperature sensing performance of fiber-optic Bragg gratings （FBGs） with soft polymeric coating, which can be used to sense internal strain in superconducting coils, are evaluated under variable cryogenic field and magnetic field. The response to a temperature and strain change of coated-soft polymeric FBGs is tested by comparing with those of coated-metal FBGs. The results indicate that the coated-soft polymeric FBGs can freely detect temperature and thermal strain, their At variable magnetic field, the tested results indicate accuracy and repeatability are also discussed in detail. that the cross-coupling effects of FBGs with different matrixes are not negligible to measure electromagnetic strain during fast excitation. The present results are expected to be able to provide basis measurements on the strain of pulsed superconducting magnet/cable （cable- around-conduit conductors, cable-in-conduit conductors）, independently or utilized together with other strain measurement methods.

Experimental Verification and Research for the Distortion in the Integrated Frequency Responses of the High-Pressure Sealed Cabin and Magnetic Field Sensor

Although magnetotelluric sounding method applied to the land is advanced, there are many difficulties when it is applied to marine environment, one of which is how to lay magnetic field sensors down to the seafloor to complete measurements. To protect the magnetic field sensors from intense erosion and high pressure, suitable high-pressure sealed cabins must be designed to load them. For the consideration of magnetic measurement and marine operation, the sealed pressure cabin should be nonmagnetic and transportable. Among all optional materials, LC4 super.hard aluminum alloy has the highest performance of price/quality ratio to make the sealed pressure cabin. However, it does not mean that the high-pressure sealed cabin made using LC4 will be perfect in performance. In fact, because of its weak magnetism, the pressure cabin made using LC4 has distorting effect on frequency responses of the magnetic field sensors sealed in it. This distorting effect does not affect the use of the magnetic field sensor, but if we want to eliminate its effect, we should study it by experimental measurements. In our experiment tests, frequency sweep magnetic field as excitation signal was used, and then responses of the magnetic field sensor before and after being loaded into the high-pressure sealed cabin were measured. Finally, normalized abnormal curves for the frequency responses were obtained, through which we could show how the high-pressure sealed cabin produces effects on the responses of the magnetic field sensor. Experimental results suggest that the response distortion induced by the sealed pressure cabin appears on mid- and high-frequency areas. Using experimental results as standardization data, the frequency responses collected from seafloor magnetotelluric measurements can be corrected to restore real information about the seafloor field source.

A SIX-YEAR RETROSPECTIVE STUDY ON THE RELATIONSHIP OF SODIUM-LITHIUM COUNTERTRANSPORT WITH BLOOD PRESSURE AND SODIUM SENSITIVITY IN CHILDREN

Red-cell membrane sodium-lithium countertransport (Na+-Li+CT) and sodium sensitivity (SS) were measured in 300 children in Hanzhong.By comparison and retrospective study, the results showed:①In children with higher blood pressure(HBP) and positive rainily history (FH+),Na+-Li+ CT rate was signiricantly higher than that in controls (P<0. 01).②6-year retrospective review of blood pressure evolution, the blood pressure increased degree (ASBP) in children with higher Na+-Li+ CT rate was much greater than that in those with lower one (P<0.05), and at the same time,the percentiles of systolic blood pressure (PSBP) for children with higher countertransport mostly kept rising or kept higher levels during this period.③In children with SS, Na+-Li+ CT rate was increased than that in SR group (P<0. 01),and was correlated to the concentration of intra-erythrocytic Na+ (P= 0.004).These suggest that, as intermediate phenotype of essential hypertension, red-cell membrane sodium-lithium countertransport defect could participate in the regulation of blood pressure and pathogensis or hypertension development in children.

The Effect of Temperature and Doping Level on the Characteristics of Piezoresistive Pressure Sensor

Piezoresistive pressure sensors based on silicon have a large thermal drift because of their high sensitivity to temperature. The study of the effect of the temperature and doping level on characteristics of these sensors is essential to define the parameters that cause the output characteristics drift. In this study, we adopted the model of Kanda to determine the effect of the temperature and of doping level on the piezoresistivity of the Silicon monocrystal. This is to represent P(N,T) and for p-type silicon as functions of impurity concentration for different temperatures. This allows us to see the effect of temperature and doping concentration on the output characteristics of the sensor. Finally, we study the geometric influence parameters and doping on these characteristics to optimize the sensor performance. This study allows us to predict the sensor behavior against temperature and to minimize this effect by optimizing the doping concentration.

The Sensitivity of TE Filed Propagating in LHM-Antiferromagnetic Sensor

A three-layer waveguide structure sensor consists of LHMs （left-handed materials） film surrounded by dielectric cladding and antiferromagnetie substrate is proposed. LHMs known as MTMs （metamaterials） have simultaneous negative permeability and permittivity. The dispersion relation for the structure is derived for TE guided modes. Two ranges of frequencies are chosen such that Voigt permeability,μv, either negative or positive. The sensitivity is proven to be affected by different parameters including the film thickness, LHM parameters, and Voigt frequency.

Flaw Detection Capability and Sensitivity in the Inspection of Nuclear Containment Liner and Shell Mock-Ups Utilizing a Magnetostrictive Sensor (MsS) Guided Wave UT Technique

This paper describes the results of a project on the inspection of visually inaccessible areas of nuclear containment liners and shells via the advanced Magnetostrictive sensor (MsS) Guided Wave (GW) nondestructive inspection technique. Full scale mockups that simulated shell and liner regions of interest in the containment of both a Pressurized Water Reactor (PWR) and Boiling Water Reactor (BWR) were constructed. Inspections were performed on the mock-ups in three stages to discern the signal attenuation caused by flaws and caused by concrete in the structures. The effect of concrete being in close proximity to the liner and shell was determined, and the capability to detect and size flaws via this GW technique was evaluated.

Nanocellulose-Assisted Construction of Multifunctional MXene-Based Aerogels with Engineering Biomimetic Texture for Pressure Sensor and Compressible Electrode

Multifunctional architecture with intriguing structural design is highly desired for realizing the promising performances in wearable sensors and flexible energy storage devices.Cellulose nanofiber(CNF)is employed for assisting in building conductive,hyperelastic,and ultralight Ti_(3)C_(2)T_(x)MXene hybrid aerogels with oriented tracheid-like texture.The biomimetic hybrid aerogels are constructed by a facile bidirectional freezing strategy with CNF,carbon nanotube(CNT),and MXene based on synergistic electrostatic interaction and hydrogen bonding.Entangled CNF and CNT“mortars”bonded with MXene“bricks”of the tracheid structure produce good interfacial binding,and superior mechanical strength(up to 80%compressibility and extraordinary fatigue resistance of 1000 cycles at 50%strain).Benefiting from the biomimetic texture,CNF/CNT/MXene aerogel shows ultralow density of 7.48 mg cm^(-3)and excellent electrical conductivity(~2400 S m^(-1)).Used as pressure sensors,such aerogels exhibit appealing sensitivity performance with the linear sensitivity up to 817.3 kPa^(-1),which affords their application in monitoring body surface information and detecting human motion.Furthermore,the aerogels can also act as electrode materials of compressive solid-state supercapacitors that reveal satisfactory electrochemical performance(849.2 mF cm^(-2)at 0.8 mA cm^(-2))and superior long cycle compression performance(88%after 10,000 cycles at a compressive strain of 30%).

Flexible capacitive pressure sensor based on interdigital electrodes with porous microneedle arrays for physiological signal monitoring

Flexible pressure sensors have many potential applications in the monitoring of physiological signals because of their good biocompatibil-ity and wearability.However,their relatively low sensitivity,linearity,and stability have hindered their large-scale commercial application.Herein,aflexible capacitive pressure sensor based on an interdigital electrode structure with two porous microneedle arrays(MNAs)is pro-posed.The porous substrate that constitutes the MNA is a mixed product of polydimethylsiloxane and NaHCO3.Due to its porous and interdigital structure,the maximum sensitivity(0.07 kPa-1)of a porous MNA-based pressure sensor was found to be seven times higher than that of an imporous MNA pressure sensor,and it was much greater than that of aflat pressure sensor without a porous MNA structure.Finite-element analysis showed that the interdigital MNA structure can greatly increase the strain and improve the sensitivity of the sen-sor.In addition,the porous MNA-based pressure sensor was found to have good stability over 1500 loading cycles as a result of its bilayer parylene-enhanced conductive electrode structure.Most importantly,it was found that the sensor could accurately monitor the motion of afinger,wrist joint,arm,face,abdomen,eye,and Adam’s apple.Furthermore,preliminary semantic recognition was achieved by monitoring the movement of the Adam’s apple.Finally,multiple pressure sensors were integrated into a 33 array to detect a spatial pressure distribu-×tion.Compared to the sensors reported in previous works,the interdigital electrode structure presented in this work improves sensitivity and stability by modifying the electrode layer rather than the dielectric layer.

Influence of Temperature on the Inter-pressure of Soil Water Tension with Correcting Method

When the electronic temperature sensor was incorporated into a system of soil water tension and the insidetube temperature was monitored in real time, it is concluded that the inside temperature increased by 26.9 ℃ and the inside pressure changed about 14.6 Kpa, when the pottery soil was replaced by the sealing plug. When the soil water was relatively stable in the experimental salvers, the in-side pressure stil varied regularly with the temperature. When the inside temperature increased by 22.2 ℃, the inside pressure varied about 7.4 Kpa. Through com-pensation calculation of the inside tension, the temperature in the warming and cooling periods was compensated, which was useful to correct the tension measurement errors induced from the changing temperature. When the measuring interval was 4 hours and the temperature difference was 18.1 ℃, the tension difference of both points was only 0.278 Kpa, compared to the difference up to 6.5 Kpa before compensation.