The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced ...The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced thermal conductivity in contrast with the currently used yttria-partially stabilized zirconia (YSZ) in high operating temperature environments.This review summarizes the recent progress on rare earth zirconates for TBCs that insulate high-temperature gas from hot-section components in gas turbines.Based on the first principles,molecular dynamics,and new data-driven calculation approaches,doping and high-entropy strategies have now been adopted in advanced TBC materials design.In this paper,the solid-state heat transfer mechanism of TBCs is explained from two aspects,including heat conduction over the full operating temperature range and thermal radiation at medium and high temperature.This paper also provides new insights into design considerations of adaptive TBC materials,and the challenges and potential breakthroughs are further highlighted for extreme environmental applications.Strategies for improving thermophysical performance are proposed in two approaches:defect engineering and material compositing.展开更多
Dielectric barrier discharge(DBD)plasma excited by a high-frequency alternating-current(AC)power supply is widely employed for the degradation of volatile organic compounds(VOCs).However,the thermal effect generated d...Dielectric barrier discharge(DBD)plasma excited by a high-frequency alternating-current(AC)power supply is widely employed for the degradation of volatile organic compounds(VOCs).However,the thermal effect generated during the discharge process leads to energy waste and low energy utilization efficiency.In this work,an innovative DBD thermally-conducted catalysis(DBD-TCC)system,integrating high-frequency AC-DBD plasma and its generated thermal effects to activate the Co/SBA-15 catalyst,was employed for toluene removal.Specifically,Co/SBA-15 catalysts are closely positioned to the ground electrode of the plasma zone and can be heated and activated by the thermal effect when the voltage exceeds 10 k V.At12.4 k V,the temperature in the catalyst zone reached 261℃ in the DBD-TCC system,resulting in an increase in toluene degradation efficiency of 17%,CO_(2)selectivity of 21.2%,and energy efficiency of 27%,respectively,compared to the DBD system alone.In contrast,the DBD thermally-unconducted catalysis(DBD-TUC)system fails to enhance toluene degradation due to insufficient heat absorption and catalytic activation,highlighting the crucial role of AC-DBD generated heat in the activation of the catalyst.Furthermore,the degradation pathway and mechanism of toluene in the DBD-TCC system were hypothesized.This work is expected to provide an energy-efficient approach for high-frequency AC-DBD plasma removal of VOCs.展开更多
This paper mainly introduces the research progress on interface failure behavior in high-temperature alloy surface thermal barrier coating systems.The degradation failure and structural evolution behavior during high-...This paper mainly introduces the research progress on interface failure behavior in high-temperature alloy surface thermal barrier coating systems.The degradation failure and structural evolution behavior during high-temperature service were analyzed for the matrix/bonding layer interface,bonding layer/TGO interface,and TGO/ceramic layer interface in thermal barrier coatings.The research focus and direction that affect the interface performance of thermal barrier coatings were proposed.展开更多
Thermal barrier coating (TBC) revolutionized the industry by allowing higher operating temperatures for equipment, such as gas turbines in the aeronautical industry. However, at high temperatures, the TBC is exposed t...Thermal barrier coating (TBC) revolutionized the industry by allowing higher operating temperatures for equipment, such as gas turbines in the aeronautical industry. However, at high temperatures, the TBC is exposed to the attack of molten silicates, known as CMAS (Calcium-Magnesium-Alumino-Silicate), which are particles from the environment that infiltrate the TBC, causing delamination. In this study, samples coated with TBC by thermal spray and covered with CMAS were evaluated at temperatures of 1200˚C and 1250˚C. For each temperature, exposure times of 1 h and 5 h were used. Samples with longer exposure time had a considerable volume increase. The main contribution of this work was to demonstrate the non-wettability of the CMAS, even in the 5-h heat treatments, which prevented its infiltration in the deeper regions. The conditions to guarantee the formation of the silicate and its consequent wettability are also discussed.展开更多
The surface fracture toughness is an important mechanical parameter for studying the failure behavior of air plasma sprayed(APS)thermal barrier coatings(TBCs).As APS TBCs are typical multilayer porous ceramic material...The surface fracture toughness is an important mechanical parameter for studying the failure behavior of air plasma sprayed(APS)thermal barrier coatings(TBCs).As APS TBCs are typical multilayer porous ceramic materials,the direct applications of the traditional single edge notched beam(SENB)method that ignores those typical structural characters may cause errors.To measure the surface fracture toughness more accurately,the effects of multilayer and porous characters on the fracture toughness of APS TBCs should be considered.In this paper,a modified single edge V-notched beam(MSEVNB)method with typical structural characters is developed.According to the finite element analysis(FEA),the geometry factor of the multilayer structure is recalculated.Owing to the narrower V-notches,a more accurate critical fracture stress is obtained.Based on the Griffith energy balance,the reduction of the crack surface caused by micro-defects is corrected.The MSEVNB method can measure the surface fracture toughness more accurately than the SENB method.展开更多
A columnar Al film was firstly deposited on the top of 7%Y2O3？stabilized zirconia （7YSZ） ceramic coating in thermal barrier coating （TBC） system by magnetron sputtering. A vacuum treatment was then carried out at...A columnar Al film was firstly deposited on the top of 7%Y2O3？stabilized zirconia （7YSZ） ceramic coating in thermal barrier coating （TBC） system by magnetron sputtering. A vacuum treatment was then carried out at 700 °C for 1 h and 900 °C for 5 h to improve the erosion resistance of Al-deposited TBC. Aα-Al2O3 layer was in situ synthesized on the top of 7YSZ coating via vacuum heat treatment. The microstructure evolution of Al-deposited TBC illustrated that a loose surface-layer and a dense sub-layer formed on the top of 7YSZ coating after vacuum treatment. The phase structures of the as-sprayed TBC and the Al-deposited TBC after vacuum heat treatment were characterized by X-ray diffraction （XRD） and transmission electron microscope （TEM） assisted with focused ion beam （FIB）. Particulate erosion resistances of the as-sprayed TBC and treated TBC were compared at room temperature. In addition, erosion mechanism and schematic diagram were proposed. The results show that the Al-deposited TBC after vacuum heat treatment has better particulate erosion resistance than the as-sprayed one.展开更多
3Gd2O3-3Yb2O3-4Y2O3 （mole fraction, %） co-doped ZrO2 （GY-YSZ） thermal barrier coatings （TBCs） were produced by electron beam physical vapor deposition （EB-PVD）. The oxidation behavior of GY-YSZ at 1 050 ℃ was...3Gd2O3-3Yb2O3-4Y2O3 （mole fraction, %） co-doped ZrO2 （GY-YSZ） thermal barrier coatings （TBCs） were produced by electron beam physical vapor deposition （EB-PVD）. The oxidation behavior of GY-YSZ at 1 050 ℃ was investigated using impedance spectroscopy （IS） combined with scanning electron microscopy （SEM）, Raman spectroscopy and X-ray diffractometry （XRD）. Various electrical responses observed in the impedance spectra corresponding to GY-YSZ grains and grain boundaries were explained using circuit modeling. The change in the conduction mechanism of GY-YSZ was found to be related to the O^2- vacancy and lattice distortion due to the stabilizer diffusion during the oxidation. The results also suggested that the specific oxidation information about the GY-YSZ grains and grain boundaries should be acquired at a moderate measurement temperature, which was related to the resistance value in the impedance spectra. The resistance values of the GY-YSZ grains and grain boundaries should be measured at 200 ℃ and 300 ℃, respectively.展开更多
Pyrochlore oxides of general compositions, A2Zr2O7, where A is a 3＋ cation （La to Lu）, are promising candidate materials for applications as high temperature thermal barrier coatings because of their high melting p...Pyrochlore oxides of general compositions, A2Zr2O7, where A is a 3＋ cation （La to Lu）, are promising candidate materials for applications as high temperature thermal barrier coatings because of their high melting points, high thermal expansion coefficients, and low thermal conductivities. In this study, oxides of Sm2Zr2O7, （Smo.75La0.25）2Zr2O7, （Sm0.5 La0.5）2 ZreO7, （Sm0.25La0.75）eZr2O7 and La2Zr2O7 were prepared by solid reactions at 1600℃ for 10 h using Sm2O3, La2O3 and ZrO2 as the reactants. The phase compositions of these ceramic materials were analyzed by X-ray diffractometer （XRD） and fourier transform infrared spectroscopy （FT-IR） methods, respectively. The microstructure was observed by scanning electron microscope （SEM）. The thermal conductivities of these ceramic materials were measured using laser-flash method. XRD and FT-IR results showed that pure ceramic materials with pyrochlore structure were prepared successfully. SEM results indicated that microstructures of these ceramic materials were dense and grain boundaries were very clean. The La2O3 doped Sm2Zr2O7 pyrochlores （Sm0.75 La0.25）2Zr2O7 and （Sm0.5 La0.5）2 Zr2O7 had lower thermal conductivity than the undoped Sm2Zr2O7. The thermal conductivity of （Sm0.25La0.75）2Zr2O7 was found to be lower than that of La2Zr2O7. The results showed that these ceramic materials had the potential to be used as candidate materials for TBCs.展开更多
The effect of rare earth doping on thermo-physical properties of lanthanum zirconate was investigated. Oxide powders of various compositions La2Zr2O7 were synthesized by coprecipitation-calcination method. High-temper...The effect of rare earth doping on thermo-physical properties of lanthanum zirconate was investigated. Oxide powders of various compositions La2Zr2O7 were synthesized by coprecipitation-calcination method. High-temperature dilatometer, DSC, and laser thermal diffusivity methods were used to analyze thermal expansion coefficient （TEC）, specific heat, and thermal diffusivity. The results showed that CeO2 doped pyrochlores La2（Zr1.8Ce0.2）2O7 and La1.7（DyNd）0.15（Zr0.8Ce0.2）2O7 had higher TEC than La2Zr2O7 and La1.7Dy0.3Zr2O7. La2（Zr1.8Ce0.2）2O7, La1.7Dy0.3Zr2O7, and La1.7（DyNd）0.15（Zr0.8Ce0.2）2O7 had lower thermal conductivity than undoped La2Zr2O7. The Dy2O3, Nd2O3, and CeO2 codoped composition showed the lowest thermal conductivity and the highest TEC. Thermo-physical results also indicated that TEC of rare earth oxide doped La2Zr2O7 ceramic was slightly higher than that of conventional ZrO2-8Wt.% Y2O3 （8YSZ）, and its thermal conductivity was lower than that of 8YSZ.展开更多
Porous α-Al2O3 thermal barrier coatings （TBCs） containing dispersed Pt particles were prepared by cathode plasma electrolytic deposition （CPED）. The influence of the Pt particles on the microstructure of the coat...Porous α-Al2O3 thermal barrier coatings （TBCs） containing dispersed Pt particles were prepared by cathode plasma electrolytic deposition （CPED）. The influence of the Pt particles on the microstructure of the coatings and the CPED process were studied. The prepared coatings were mainly composed of α-Al2O3. The average thickness of the coatings was approximately 100 μm. Such single-layer TBCs ex- hibited not only excellent high-temperature cyclic oxidation and spallation resistance, but also good thermal insulation properties. Porous α-Al2O3 TBCs inhibit further oxidation of alloy substrates because of their extremely low oxygen diffusion rate, provide good thermal insu- lation because of their porous structure, and exhibit excellent mechanical properties because of the toughening effect of the Pt particles and because of stress relaxation induced by deformation of the porous structure.展开更多
NiCoCrAlTaY bond coat was deposited on pure nickel substrate by low pressure plasma spraying(LPPS), and ZrO2-8%Y2O3 (mass fraction) nanostructured and ZrO2-7%Y2O3 (mass fraction) conventional thermal barrier coatings(...NiCoCrAlTaY bond coat was deposited on pure nickel substrate by low pressure plasma spraying(LPPS), and ZrO2-8%Y2O3 (mass fraction) nanostructured and ZrO2-7%Y2O3 (mass fraction) conventional thermal barrier coatings(TBCs) were deposited by air plasma spraying(APS). The thermal shock behaviors of the nanostructured and conventional TBCs were investigated by quenching the coating samples in cold water from 1 150, 1 200 and 1 250 ℃, respectively. Scanning electron microscopy(SEM) was used to examine the microstructures of the samples after thermal shock testing. Energy dispersive analysis of X-ray(EDAX) was used to analyze the interface diffusion behavior of the bond coat elements. X-ray diffractometry(XRD) was used to analyze the constituent phases of the samples. Experimental results indicate that the nanostructured TBC is superior to the conventional TBC in thermal shock performance. Both the nanostructured and conventional TBCs fail along the bond coat/substrate interface. The constituent phase of the as-sprayed conventional TBC is diffusionless-transformed tetragonal(t′). However, the constituent phase of the as-sprayed nanostructured TBC is cubic(c). There is a difference in the crystal size at the spalled surfaces of the nanostructured and conventional TBCs. The constituent phases of the spalled surfaces are mainly composed of Ni2.88Cr1.12 and oxides of bond coat elements.展开更多
Thermal annealing effects on gamma irradiated Ni/4 H-SiC Schottky barrier diode(SBD) characteristics are analyzed over a wide range of temperatures(400–1100 °C). The annealing induced variations in the concentra...Thermal annealing effects on gamma irradiated Ni/4 H-SiC Schottky barrier diode(SBD) characteristics are analyzed over a wide range of temperatures(400–1100 °C). The annealing induced variations in the concentration of deep level traps in the SBDs are identified by thermally stimulated capacitance(TSCAP). A little decrease in the trap density at E_C – 0.63 eV and E_C –1.13 eV is observed up to the annealing temperature of 600 °C. Whereas, a gamma induced trap at E_C – 0.89 eV disappeared after annealing at 500 °C, revealing that its concentration(< 1013 cm-3) is reduced below the detection limit of the TSCAP technique.The electrical characteristics of irradiated SBDs are considerably changed at each annealing temperature. To understand the anomalous variations in the post-annealing characteristics, the interface state density distribution in the annealed SBDs is extracted.The electrical properties are improved at 400 °C due to the reduction in the interface trap density. However, from 500 °C, the electrical parameters are found to degrade with the annealing temperature because of the increase in the interface trap density.From the results, it is noted that the rectifying nature of the SBDs vanishes at or above 800 °C.展开更多
The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY Y 2O 3 stabilized ZrO 2 transition layer and Y 2O 3 stabilized ZrO 2 ceramic layer are prepared on nickel alloy substrates using the plasma spray ...The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY Y 2O 3 stabilized ZrO 2 transition layer and Y 2O 3 stabilized ZrO 2 ceramic layer are prepared on nickel alloy substrates using the plasma spray technique. The relationship among the composition, structure and property of the coatings are investiga ted by means of optical microscope, scanning electronic microscope and the experiments of thermal shock resistance cycling and high temperature oxidation resistance. The results show that the structure design of introdu cing a transition layer between Ni alloy substrate and ZrO 2 ceramic coating guarantees the high quality and properties of the coatings; ZrO 2 coatings doped with a little SiO 2 possesses better thermal shock resistance and more excellent hot corrosion resistance as compared with ZrO 2 coating materials without SiO 2 ;the improvement in performance of ZrO 2 coating doped with SiO 2 is due to forming more dense coating structure by self closing effects of the flaws and pores in the ZrO 2 coatings.展开更多
The performances of gradient thermal barrier coatings (GTBCs) produced by EB-PVD were evaluated by isothermal oxidation and cyclic hot corrosion (HTHC) tests. Compared with conventional two-layered TBCs, the GTBCs exh...The performances of gradient thermal barrier coatings (GTBCs) produced by EB-PVD were evaluated by isothermal oxidation and cyclic hot corrosion (HTHC) tests. Compared with conventional two-layered TBCs, the GTBCs exhibite better resistance to not only oxidation but also hot-corrosion. A dense Al2O3 layer in the GTBCs effectively prohibites inward diffusion of O and S and outward diffusion of Al and Cr during the tests. On the other hand, an "inlaid" interface, resulting from oxidation of the Al along the columnar grains of the bond coat, enhances the adherence of AI2O3 layer. Failure of the GTBC finally occurred by cracking at the interface between the bond coat and AI2O3 layer, due to the combined effect of sulfidation of the bond coat and thermal cvcling.展开更多
Laboratory experiments were conducted to study the spallation behaviour of thermal barrier coatings(TBCs) on aero-engine turbine blades manufactured by the electron-beam physical vapour deposition technique(EB-PVD). I...Laboratory experiments were conducted to study the spallation behaviour of thermal barrier coatings(TBCs) on aero-engine turbine blades manufactured by the electron-beam physical vapour deposition technique(EB-PVD). Intact blades were heated at temperature 1135℃ in a furnace for certain time and then cooled to the room temperature in the laboratory condition. It was found that no spallation occurred during cooling, but spallation happened at constant room temperature after cooling. The spallation mechanism is studied by using the mechanical model developed(Harvey 2017 and Wang 2017), which are based on the hypothesis of pockets of energy concentration(PECs). Some observations of the spallation behaviour are well predicted by the model.展开更多
In this study, an etched-SiO-film grating fabrication technique based on solute-solvent separation soft lithography is developed. By using this new technique, high temperature grating with frequency of 600 lines/mm is...In this study, an etched-SiO-film grating fabrication technique based on solute-solvent separation soft lithography is developed. By using this new technique, high temperature grating with frequency of 600 lines/mm is successfully fabricated on the surface of thermal barrier coatings(TBCs). During the fabrication process, the microstructure and chemical compositions of ceramic coating before and after polishing is analyzed with a digital microscope and the energy dispersive X-ray spectroscope(EDS) in scanning electron microscope(SEM). And then the grating on TBCs is heated at the temperature ranging from 300℃ to 1000℃ for examining the high temperature resistance. In the practical application, the displacement and strain field around the crack on the ceramic surface are investigated with geometry phase analysis(GPA). The successful results verify that the etched-SiO-film grating has a good oxidation resistance and can be applied to high temperature deformation measurement of TBCs.展开更多
基金the financial support from the National Natural Science Foundation of China(Nos.51572061,51621091,and 51321061)the Heilongjiang Touyan Team Program。
文摘The A_(2)B_(2)O_(7)-type rare earth zirconate compounds have been considered as promising candidates for thermal barrier coating(TBC) materials because of their low sintering rate,improved phase stability,and reduced thermal conductivity in contrast with the currently used yttria-partially stabilized zirconia (YSZ) in high operating temperature environments.This review summarizes the recent progress on rare earth zirconates for TBCs that insulate high-temperature gas from hot-section components in gas turbines.Based on the first principles,molecular dynamics,and new data-driven calculation approaches,doping and high-entropy strategies have now been adopted in advanced TBC materials design.In this paper,the solid-state heat transfer mechanism of TBCs is explained from two aspects,including heat conduction over the full operating temperature range and thermal radiation at medium and high temperature.This paper also provides new insights into design considerations of adaptive TBC materials,and the challenges and potential breakthroughs are further highlighted for extreme environmental applications.Strategies for improving thermophysical performance are proposed in two approaches:defect engineering and material compositing.
基金supported by National Natural Science Foundation of China(No.52177130)the Key Projects for Industrial Prospects and Core Technology Research in Suzhou City(No.SYC2022029)。
文摘Dielectric barrier discharge(DBD)plasma excited by a high-frequency alternating-current(AC)power supply is widely employed for the degradation of volatile organic compounds(VOCs).However,the thermal effect generated during the discharge process leads to energy waste and low energy utilization efficiency.In this work,an innovative DBD thermally-conducted catalysis(DBD-TCC)system,integrating high-frequency AC-DBD plasma and its generated thermal effects to activate the Co/SBA-15 catalyst,was employed for toluene removal.Specifically,Co/SBA-15 catalysts are closely positioned to the ground electrode of the plasma zone and can be heated and activated by the thermal effect when the voltage exceeds 10 k V.At12.4 k V,the temperature in the catalyst zone reached 261℃ in the DBD-TCC system,resulting in an increase in toluene degradation efficiency of 17%,CO_(2)selectivity of 21.2%,and energy efficiency of 27%,respectively,compared to the DBD system alone.In contrast,the DBD thermally-unconducted catalysis(DBD-TUC)system fails to enhance toluene degradation due to insufficient heat absorption and catalytic activation,highlighting the crucial role of AC-DBD generated heat in the activation of the catalyst.Furthermore,the degradation pathway and mechanism of toluene in the DBD-TCC system were hypothesized.This work is expected to provide an energy-efficient approach for high-frequency AC-DBD plasma removal of VOCs.
文摘This paper mainly introduces the research progress on interface failure behavior in high-temperature alloy surface thermal barrier coating systems.The degradation failure and structural evolution behavior during high-temperature service were analyzed for the matrix/bonding layer interface,bonding layer/TGO interface,and TGO/ceramic layer interface in thermal barrier coatings.The research focus and direction that affect the interface performance of thermal barrier coatings were proposed.
文摘Thermal barrier coating (TBC) revolutionized the industry by allowing higher operating temperatures for equipment, such as gas turbines in the aeronautical industry. However, at high temperatures, the TBC is exposed to the attack of molten silicates, known as CMAS (Calcium-Magnesium-Alumino-Silicate), which are particles from the environment that infiltrate the TBC, causing delamination. In this study, samples coated with TBC by thermal spray and covered with CMAS were evaluated at temperatures of 1200˚C and 1250˚C. For each temperature, exposure times of 1 h and 5 h were used. Samples with longer exposure time had a considerable volume increase. The main contribution of this work was to demonstrate the non-wettability of the CMAS, even in the 5-h heat treatments, which prevented its infiltration in the deeper regions. The conditions to guarantee the formation of the silicate and its consequent wettability are also discussed.
基金Project supported by the National Natural Science Foundation of China(Nos.12172048 and 12027901)the National Science and Technology Major Project of China(Nos.2019-Ⅶ-0007-0147 and 2017-Ⅵ-0020-0093)。
文摘The surface fracture toughness is an important mechanical parameter for studying the failure behavior of air plasma sprayed(APS)thermal barrier coatings(TBCs).As APS TBCs are typical multilayer porous ceramic materials,the direct applications of the traditional single edge notched beam(SENB)method that ignores those typical structural characters may cause errors.To measure the surface fracture toughness more accurately,the effects of multilayer and porous characters on the fracture toughness of APS TBCs should be considered.In this paper,a modified single edge V-notched beam(MSEVNB)method with typical structural characters is developed.According to the finite element analysis(FEA),the geometry factor of the multilayer structure is recalculated.Owing to the narrower V-notches,a more accurate critical fracture stress is obtained.Based on the Griffith energy balance,the reduction of the crack surface caused by micro-defects is corrected.The MSEVNB method can measure the surface fracture toughness more accurately than the SENB method.
基金Project(2012CB625100)supported by the National Basic Research Program of ChinaProject(2012AA03A512)supported by the National High-tech Research and Development Program of China
文摘A columnar Al film was firstly deposited on the top of 7%Y2O3？stabilized zirconia （7YSZ） ceramic coating in thermal barrier coating （TBC） system by magnetron sputtering. A vacuum treatment was then carried out at 700 °C for 1 h and 900 °C for 5 h to improve the erosion resistance of Al-deposited TBC. Aα-Al2O3 layer was in situ synthesized on the top of 7YSZ coating via vacuum heat treatment. The microstructure evolution of Al-deposited TBC illustrated that a loose surface-layer and a dense sub-layer formed on the top of 7YSZ coating after vacuum treatment. The phase structures of the as-sprayed TBC and the Al-deposited TBC after vacuum heat treatment were characterized by X-ray diffraction （XRD） and transmission electron microscope （TEM） assisted with focused ion beam （FIB）. Particulate erosion resistances of the as-sprayed TBC and treated TBC were compared at room temperature. In addition, erosion mechanism and schematic diagram were proposed. The results show that the Al-deposited TBC after vacuum heat treatment has better particulate erosion resistance than the as-sprayed one.
基金Projects (50771009, 50731001 and 51071013) supported by the National Natural Science Foundations of China Project (2010CB631200) supported by the National Basic Research Program of China
文摘3Gd2O3-3Yb2O3-4Y2O3 （mole fraction, %） co-doped ZrO2 （GY-YSZ） thermal barrier coatings （TBCs） were produced by electron beam physical vapor deposition （EB-PVD）. The oxidation behavior of GY-YSZ at 1 050 ℃ was investigated using impedance spectroscopy （IS） combined with scanning electron microscopy （SEM）, Raman spectroscopy and X-ray diffractometry （XRD）. Various electrical responses observed in the impedance spectra corresponding to GY-YSZ grains and grain boundaries were explained using circuit modeling. The change in the conduction mechanism of GY-YSZ was found to be related to the O^2- vacancy and lattice distortion due to the stabilizer diffusion during the oxidation. The results also suggested that the specific oxidation information about the GY-YSZ grains and grain boundaries should be acquired at a moderate measurement temperature, which was related to the resistance value in the impedance spectra. The resistance values of the GY-YSZ grains and grain boundaries should be measured at 200 ℃ and 300 ℃, respectively.
基金supported by Doctoral Fund of Henan Institute of Engineering (D2007012)
文摘Pyrochlore oxides of general compositions, A2Zr2O7, where A is a 3＋ cation （La to Lu）, are promising candidate materials for applications as high temperature thermal barrier coatings because of their high melting points, high thermal expansion coefficients, and low thermal conductivities. In this study, oxides of Sm2Zr2O7, （Smo.75La0.25）2Zr2O7, （Sm0.5 La0.5）2 ZreO7, （Sm0.25La0.75）eZr2O7 and La2Zr2O7 were prepared by solid reactions at 1600℃ for 10 h using Sm2O3, La2O3 and ZrO2 as the reactants. The phase compositions of these ceramic materials were analyzed by X-ray diffractometer （XRD） and fourier transform infrared spectroscopy （FT-IR） methods, respectively. The microstructure was observed by scanning electron microscope （SEM）. The thermal conductivities of these ceramic materials were measured using laser-flash method. XRD and FT-IR results showed that pure ceramic materials with pyrochlore structure were prepared successfully. SEM results indicated that microstructures of these ceramic materials were dense and grain boundaries were very clean. The La2O3 doped Sm2Zr2O7 pyrochlores （Sm0.75 La0.25）2Zr2O7 and （Sm0.5 La0.5）2 Zr2O7 had lower thermal conductivity than the undoped Sm2Zr2O7. The thermal conductivity of （Sm0.25La0.75）2Zr2O7 was found to be lower than that of La2Zr2O7. The results showed that these ceramic materials had the potential to be used as candidate materials for TBCs.
基金supported by the Postdoctoral Foundation of China (20060400261)the Special Finance Scheme of Post Doctoral Foundation of China (200801350)
文摘The effect of rare earth doping on thermo-physical properties of lanthanum zirconate was investigated. Oxide powders of various compositions La2Zr2O7 were synthesized by coprecipitation-calcination method. High-temperature dilatometer, DSC, and laser thermal diffusivity methods were used to analyze thermal expansion coefficient （TEC）, specific heat, and thermal diffusivity. The results showed that CeO2 doped pyrochlores La2（Zr1.8Ce0.2）2O7 and La1.7（DyNd）0.15（Zr0.8Ce0.2）2O7 had higher TEC than La2Zr2O7 and La1.7Dy0.3Zr2O7. La2（Zr1.8Ce0.2）2O7, La1.7Dy0.3Zr2O7, and La1.7（DyNd）0.15（Zr0.8Ce0.2）2O7 had lower thermal conductivity than undoped La2Zr2O7. The Dy2O3, Nd2O3, and CeO2 codoped composition showed the lowest thermal conductivity and the highest TEC. Thermo-physical results also indicated that TEC of rare earth oxide doped La2Zr2O7 ceramic was slightly higher than that of conventional ZrO2-8Wt.% Y2O3 （8YSZ）, and its thermal conductivity was lower than that of 8YSZ.
基金the financial support from the National Natural Science Foundation of China(Nos.52172067,92160202)Natural Science Foundation of Guangdong Province,China(Nos.2021B1515020038,2020B1515020036)+1 种基金Guangdong Special Support Program,China(No.2019BT02C629)Guangdong Academy of Sciences Program,China(No.2020GDASYL20200104030)。
基金supported by the Chinese National Natural Science Foundation (Grant No. 51271030)
文摘Porous α-Al2O3 thermal barrier coatings （TBCs） containing dispersed Pt particles were prepared by cathode plasma electrolytic deposition （CPED）. The influence of the Pt particles on the microstructure of the coatings and the CPED process were studied. The prepared coatings were mainly composed of α-Al2O3. The average thickness of the coatings was approximately 100 μm. Such single-layer TBCs ex- hibited not only excellent high-temperature cyclic oxidation and spallation resistance, but also good thermal insulation properties. Porous α-Al2O3 TBCs inhibit further oxidation of alloy substrates because of their extremely low oxygen diffusion rate, provide good thermal insu- lation because of their porous structure, and exhibit excellent mechanical properties because of the toughening effect of the Pt particles and because of stress relaxation induced by deformation of the porous structure.
基金Project(1343-77212) supported by the Innovation Program for Graduate Students of Central South University, China
文摘NiCoCrAlTaY bond coat was deposited on pure nickel substrate by low pressure plasma spraying(LPPS), and ZrO2-8%Y2O3 (mass fraction) nanostructured and ZrO2-7%Y2O3 (mass fraction) conventional thermal barrier coatings(TBCs) were deposited by air plasma spraying(APS). The thermal shock behaviors of the nanostructured and conventional TBCs were investigated by quenching the coating samples in cold water from 1 150, 1 200 and 1 250 ℃, respectively. Scanning electron microscopy(SEM) was used to examine the microstructures of the samples after thermal shock testing. Energy dispersive analysis of X-ray(EDAX) was used to analyze the interface diffusion behavior of the bond coat elements. X-ray diffractometry(XRD) was used to analyze the constituent phases of the samples. Experimental results indicate that the nanostructured TBC is superior to the conventional TBC in thermal shock performance. Both the nanostructured and conventional TBCs fail along the bond coat/substrate interface. The constituent phase of the as-sprayed conventional TBC is diffusionless-transformed tetragonal(t′). However, the constituent phase of the as-sprayed nanostructured TBC is cubic(c). There is a difference in the crystal size at the spalled surfaces of the nanostructured and conventional TBCs. The constituent phases of the spalled surfaces are mainly composed of Ni2.88Cr1.12 and oxides of bond coat elements.
文摘Thermal annealing effects on gamma irradiated Ni/4 H-SiC Schottky barrier diode(SBD) characteristics are analyzed over a wide range of temperatures(400–1100 °C). The annealing induced variations in the concentration of deep level traps in the SBDs are identified by thermally stimulated capacitance(TSCAP). A little decrease in the trap density at E_C – 0.63 eV and E_C –1.13 eV is observed up to the annealing temperature of 600 °C. Whereas, a gamma induced trap at E_C – 0.89 eV disappeared after annealing at 500 °C, revealing that its concentration(< 1013 cm-3) is reduced below the detection limit of the TSCAP technique.The electrical characteristics of irradiated SBDs are considerably changed at each annealing temperature. To understand the anomalous variations in the post-annealing characteristics, the interface state density distribution in the annealed SBDs is extracted.The electrical properties are improved at 400 °C due to the reduction in the interface trap density. However, from 500 °C, the electrical parameters are found to degrade with the annealing temperature because of the increase in the interface trap density.From the results, it is noted that the rectifying nature of the SBDs vanishes at or above 800 °C.
文摘The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY Y 2O 3 stabilized ZrO 2 transition layer and Y 2O 3 stabilized ZrO 2 ceramic layer are prepared on nickel alloy substrates using the plasma spray technique. The relationship among the composition, structure and property of the coatings are investiga ted by means of optical microscope, scanning electronic microscope and the experiments of thermal shock resistance cycling and high temperature oxidation resistance. The results show that the structure design of introdu cing a transition layer between Ni alloy substrate and ZrO 2 ceramic coating guarantees the high quality and properties of the coatings; ZrO 2 coatings doped with a little SiO 2 possesses better thermal shock resistance and more excellent hot corrosion resistance as compared with ZrO 2 coating materials without SiO 2 ;the improvement in performance of ZrO 2 coating doped with SiO 2 is due to forming more dense coating structure by self closing effects of the flaws and pores in the ZrO 2 coatings.
文摘The performances of gradient thermal barrier coatings (GTBCs) produced by EB-PVD were evaluated by isothermal oxidation and cyclic hot corrosion (HTHC) tests. Compared with conventional two-layered TBCs, the GTBCs exhibite better resistance to not only oxidation but also hot-corrosion. A dense Al2O3 layer in the GTBCs effectively prohibites inward diffusion of O and S and outward diffusion of Al and Cr during the tests. On the other hand, an "inlaid" interface, resulting from oxidation of the Al along the columnar grains of the bond coat, enhances the adherence of AI2O3 layer. Failure of the GTBC finally occurred by cracking at the interface between the bond coat and AI2O3 layer, due to the combined effect of sulfidation of the bond coat and thermal cvcling.
文摘Laboratory experiments were conducted to study the spallation behaviour of thermal barrier coatings(TBCs) on aero-engine turbine blades manufactured by the electron-beam physical vapour deposition technique(EB-PVD). Intact blades were heated at temperature 1135℃ in a furnace for certain time and then cooled to the room temperature in the laboratory condition. It was found that no spallation occurred during cooling, but spallation happened at constant room temperature after cooling. The spallation mechanism is studied by using the mechanical model developed(Harvey 2017 and Wang 2017), which are based on the hypothesis of pockets of energy concentration(PECs). Some observations of the spallation behaviour are well predicted by the model.
基金financially supported by the National Natural Science Foundation of China(11672153,11232008)
文摘In this study, an etched-SiO-film grating fabrication technique based on solute-solvent separation soft lithography is developed. By using this new technique, high temperature grating with frequency of 600 lines/mm is successfully fabricated on the surface of thermal barrier coatings(TBCs). During the fabrication process, the microstructure and chemical compositions of ceramic coating before and after polishing is analyzed with a digital microscope and the energy dispersive X-ray spectroscope(EDS) in scanning electron microscope(SEM). And then the grating on TBCs is heated at the temperature ranging from 300℃ to 1000℃ for examining the high temperature resistance. In the practical application, the displacement and strain field around the crack on the ceramic surface are investigated with geometry phase analysis(GPA). The successful results verify that the etched-SiO-film grating has a good oxidation resistance and can be applied to high temperature deformation measurement of TBCs.
