A Kinematic Thermal Model for Descending Slabs with Velocity Boundary Layers:A Case Study for the Tonga Subducting Slab

For the purpose of investigating the influence of metastable olivine（MO） phase transformations on both deep seismicity and stagnation of slabs,we constructed a 2-dimensional finite element thermal model for a 120 Ma-old 50°dipping oceanic lithosphere descending at 10 cm/yr with velocity boundary layers,which would mitigate the interference of constant velocity field for the slab. The resulting temperatures show that most of intermediate and deep earthquakes occurring within the Tonga slab are occurring inside the 800℃and 1200℃isotherm,respectively.The elevation of olivine transformation near～410 km and respective persistence of metastable olivine and spinel within the transition zone and beneath 660 km would thus result in bimodal positive,zonal,negative density anomalies,respectively.These results together with the resulting pressure anomalies may reflect the stress pattern of the Tonga slab：（i） slab pull force exerts above a depth of～230 km;（ii） MO existence changes the buoyancy force within the transition zone and facilitates slab stagnation at a depth of 660 km;（iii） as the subducting materials accumulated over 660 km,deepest earthquakes occur due to MO transformation;（iv） a flattened‘slab’ may penetrate into the lower mantle due to the density increment of Sp transformation.

Three-stage Nonlinear Thermal Model for Microspeakers in Mobile Phones

Since microspeakers are widely used in mobile phones,high power is usually applied to obtain sufficient output sound pressure.However,the electric power is almost converted into heat,leading to the thermal problem in microspeakers.Compared with large loudspeaker,microspeakers are smaller and the under yoke is relatively closed,causing the heat transfer more complex.In this study,a three-stage nonlinear thermal model was proposed for analyzing the thermal behavior in microspeakers.The inside air is a buffer area between the voice coil and magnet,and modeled as a middle stage of the heat transfer.The forced convection is still significant in microspeakers while the eddy current can be ignored.In order to obtain the thermal parameters of the model,a corresponding parameter identification method was put forward.The basic linear parameters and forced convection parameters were all obtained by measuring and fitting the temperature curves of voice coil at different single tones.A series of experiments were conducted to verify the proposed model and parameter identification method,and the results showed good aggrement between the measured and predicted temperature curves for different input signals.The proposed model was valid and accurate,and may be helpful for the design and application of microspeakers.

Thermal modeling optimization and experimental validation for a single concentrator solar cell system with a heat sink

A single concentrator solar cell model with a heat sink is established to simulate the thermal performance of the system by varying the number, height, and thickness of fins, the base thickness and thermal resistance of the thermal conductive adhesive. Influence disciplines of those parameters on temperatures of the solar cell and heat sink are obtained. With optimized number, height and thickness of fins, and the thickness values of base of 8, 1.4 cm, 1.5 mm, and 2 mm, the lowest temperatures of the solar cell and heat sink are 41.7 ~C and 36.3 ~C respectively. A concentrator solar cell prototype with a heat sink fabricated based on the simulation optimized structure is built. Outdoor temperatures of the prototype are tested. Temperatures of the solar cell and heat sink are stabilized with time continuing at about 37 ℃-38 ℃ and 35 ℃-36 ℃respectively, slightly lower than the simulation results because of effects of the wind and cloud. Thus the simulation model enables to predict the thermal performance of the system, and the simulation results can be a reference for designing heat sinks in the field of single concentrator solar cells.

Dynamic thermal modeling and parameter identification for a monolithic laser diode module

We improved the thermal equivalent-circuit model of the laser diode module（LDM） to evaluate its thermal dynamic properties and calculate the junction temperature of the laser diode with a high accuracy.The thermal parameters and the transient junction temperature of the LDM are modeled and obtained according to the temperature of the thermistor integrated in the module.Our improved thermal model is verified indirectly by monitoring the emission wavelength of the laser diode against gas absorption lines,and several thermal parameters are obtained with the temperature uncertainty of 0.01 K in the thermal dynamic process.

THERMAL MODELLING OF COLLISIONAL OROGENY: IMPLICATIONS FOR THE ULTRA-HIGH PRESSURE METAMORPHISM

The petrological research on the ultra high pressure metamorphism (UHP) of collisional orogen indicates that the upper crustal rocks is subducted to depths exceeding 100 km, and returned to the surface rapidly. In this study, we investigate the thermal structure of collisional orogen as a slab of continental lithosphere being subducted beneath an overriding wedge of continental lithosphere by the 2 D finite element method. The advection heat transfer due to the accretion of orogenic wedge is considered. The wedge is composed of the upper crust materials through the accretion from the down going plate to the upper plate. For identifying the significance of the geometric and/or kinetic factors on the thermal structure of continental subduction, the different combinations of parameters, including dip angle of subduction zone, accretion or erosion rates, and the convergence velocity etc., are used in modelling. The time span of continental subduction in our calculation is less than 30 Ma, according to the short duration of ultra deep subduction of continental slab suggested by the preservation of metastable pre peak low pressure mineralogy assemblage in the garnet of UHP rocks. Therefore, the steep dip angle of down going plate and/or low rate of accretion favour the ultra deep subduction of upper crust materials, especially for the slower down going slab. Meanwhile, taking the erosion rate as the level of exhumation rate of UHP rocks in some orogens (i.e., 1-2 km/Ma or more) does not result in the anatexis melting of crust of the overriding plate, due to the cooling effect of the rapid down going slab. However, the temperature structures of all models are generally cooler than those recovered by thermobarometric studies of the UHP rocks. This implies the significant increase of temperature after the rapid subduction of continental slab. Following the method of Davies and von Blackenburg (1998), we show that the slab breakoff can occur at the depth exceeding 100 km. Thermal modelling on the post subduction stage shows the heating related to the plate breakoff can cause the higher temperature recorded by the exhumed UHP rocks. The higher geotherm during post subduction stage leads to the weak strength of the orogenic wedge, and favours the faster upward movement of the UHP rock slices as ductile agents. The lower temperature gradient of the subduction slab predicted by modelling suggests the cold subducting slab could have transported significant fluids to mantle depth, not released during subduction. Accordingly, the absence of coeval calc alkalic magmatism in UHP orogens might resulted from the lower temperature as well as the fluid free circumstance, both are related to the rapid subduction of cold plate. Therefore, shear heating is not needed for explanation the thermal evolution of UHP orogen. On the other hand, the post collisional or late stage granitic plutonism is closely related to the deep seated heat producing materials of the accretion wedge.

Transient Thermal Modeling in Laser Welding of Metallic/Nonmetallic Joints Using SolidWorks^(█) Software

The purpose of this research is to develop a SolidWorks? model for transient temperature field of laser welding of PMMA/SS 304 materials for application in fabrication of the ultrasonic back-plate, with a view of optimizing the experimental conditions. The study is carried out on these materials because of the increasing application of both metals and non-metals. The work focuses specifically on these materials because they have been experimentally studied previously and as such, this study can be accepted as an assessment into feasibility of using SolidWorks? model to study the temperature field of the laser welding processes of metals and non-metals. The results of the SolidWorks? transient thermal model show that there is a concentration of high temperatures at the point of contact. It also shows that temperature decreases as we move in (between laser and the top face) to the thickness of the part. Additionally the maximum temperature occurs at the last point of the welding;this may be due to the accumulation of the temperature before arriving at the end. These findings are comparable to the previous simulated and experimental results on temperature field during laser welding of PMMA/SS 304 materials. However, SolidWorks? is shown to present a challenge in modeling a moving source of laser power.

Thermal Model of High-Speed Spindle Units

For the purpose to facilitate development of high-speed Spindle Units (SUs) running on rolling bearings, we have developed a beam element model, algorithms, and software for computer analysis of thermal characteristics of SUs. The thermal model incorporates a model of heat generation in rolling bearings, a model of heat transfer from bearings, and models for estimation of temperature and temperature deformations of SU elements. We have carried out experimental test and made quantitative evaluation of the effect of operation conditions on friction and thermal characteristics of the SUs of grinding and turning machines of typical structures. It is found that the operation conditions make stronger effect on SU temperatures when rpm increases. A comparison between the results of analysis and experiment proves their good mutual correspondence and allows us to recommend application of the models and software developed for design and research of high-speed SUs running on rolling bearings.

Dynamic Thermal Model and Temperature Control of Proton Exchange Membrane Fuel Cell Stack

A dynamic thermal transfer model of a proton exchange membrane fuel cell (PEMFC) stack is developed based on energy conservation in order to reach better temperature control of PEMFC stack. Considering its uncertain parameters and disturbance, we propose a robust adaptive controller based on backstepping algorithm of Lyaponov function. Numerical simulations indicate the validity of the proposed controller.

Parameterized thermal model of a mixed mantle convection

Simple parameterized models, either whole mantle convection or layered mantleconvection, cannot explain the tectonic characteristics of the Earth's evolution history, therefore a mixed mantle convection model has been carried out in this paper. We introduce a time-dependent parameter F, which denotes the ratio betWeen the mantle material involved in whole mantle convection and the material of the entire mantle, and introduce a local Rayleigh number Raloc as well as two critical numbers Ra1 and Ra2. These parameters are used to describe the stability of the phase boundary between the upper and lower mantle. The result shows that the mixed mantle convection model is able to simulate the episodic tectonic evolution of the Earth.

Rate-equation-based VCSEL thermal model and simulation

In this paper, we present a simple thermal model of Vertical-Cavity Surface-Emitting Laser (VCSEL) light-current (LI) characteristics based on the rate-equation. The model can be implemented in conventional SPICE-like circuit simulators, including HSPICE, and be used to simulate the key features of VCSEL. The results compare favorably with experimental data from a device reported in the literature. The simple empirical model is especially suitable for Computer Aided Design (CAD), and greatly sim- plifies the design of optical communication systems.

Thermal Modeling of Cylindrical LiFePO₄Batteries

Thermal management of Li-ion batteries is important because of the high energy content and the risk of rapid temperature development in the high current range. Reliable and safe operation of these batteries is seriously endangered by high temperatures. It is important to have a simple but accurate model to evaluate the thermal behavior of batteries under a variety of operating conditions and be able to predict the internal temperature as well. To achieve this goal, a radial-axial model is developed to investigate the evolution of the temperature distribution in cylindrical Li-ion cells. Experimental data on LiFePO4 cylindrical Li-ion batteries are used to determine the overpotentials and to estimate the State-of-Charge-dependent entropies from the previously developed adaptive thermal model [1]. The heat evolution is assumed to be uniform inside the battery. Heat exchange from the battery surfaces with the ambient is non-uniform, i.e. depends on the temperature of a particular point at the surface of the cell. Furthermore, the model was adapted for implementation in battery management systems. It is shown that the model can accurately predict the temperature distribution inside the cell in a wide range of operating conditions. Good agreement with the measured temperature development has been achieved. Decreasing the heat conductivity coefficient during cell manufacturing and increasing the heat transfer coefficient during battery operation suppresses the temperature evolution. This modified model can be used for the scale-up of large size batteries and battery packs.

Thermal Modeling of a Multilayer Integrated LC Filter for Temperature Distribution Calculation

Thermal behavior of integrated passive components has become an important issue when designing these components. This paper presents the thermal modeling of a multilayer integrated LC filter used in DC-DC step-down converter for temperature distribution calculation. The approach used for this analysis is based on thermal equivalent circuit. Temperature distribution is obtained from algebraic equation, which is in vector and matrix form. The results of analytical calculation are compared with simulation results from finite element method. These results showed a good correlation.

A Kinematic Thermal Model for Descending Slabs with Velocity Boundary Layers

Kinematic models compute the temperature distribution by prescribing a constant convergent velocity for the subducting slab,resulting in an artificial velocity discontinuity,which may accelerate the heating of subducting slabs.For the purpose to moderate the influence of such artificial discontinuity, we construct a 2D thermal model for subduction zones with a velocity boundary layer,within which the velocities decrease linearly with the distance from the interfaces of slabs.Temperatures are calculated

Multi-parametric Sensitivity Analysis of Improved Transformer Thermal Models Considering Nonlinear Effect of Oil Time Constant

This paper aims to develop an approach to investigating the effect of a particular parameter on the output accuracy of transformer thermal models,i.e.sensitivity analysis,which can not only reveal the most sensitive parameter of a thermal model but also improve model output accuracies.For the first time,the nonlinear time constant(NTC)of transformer oil is proposed to reshape three practical top-oil temperature models based on an expression of nonlinear thermal conductance:the modified IEEE clause 7 model,Swift’s model,and Susa’s model.Then,the multi-parametric sensitivity analysis(MPSA)is undertaken to reveal the effect of each parameter on the model output accuracy.Through onsite data validation,the results show that the accuracy performance of the proposed NTC thermal models are improved significantly by considering the nonlinear effect of oil time constant.Moreover,the derived sensitivity performances can clearly reveal the most dominant parameter of the model,so as to simplify the model parameter identification process by reducing the number of insensitive parameters.Finally,the heat-run test data is used as a reference to validate parameters optimized through a genetic algorithm(GA),which demonstrates that the proposed NTC IEEE model has not only one sensitive parameter but also superior accuracy performance.

Parameter Estimation for Hot-spot Thermal Model of Power Transformers Using Unscented Kalman Filters

This paper presents a parameter estimation technique for the hot-spot thermal model of power transformers.The proposed technique is based on the unscented formulation of the Kalman filter,jointly considering the state variables and parameters of the dynamic thermal model.A two-stage estimation technique that takes advantage of different loading conditions is developed,in order to increase the number of parameters which can be identified.Simulation results are presented,which show that the observable parameters are estimated with an error of less than 3%.The parameter estimation procedure is mainly intended for factory testing,allowing the manufacturer to enhance the thermal model of power transformers and,therefore,its customers to increase the lifetime of these assets.The proposed technique could be additionally considered in field applications if the necessary temperature measurements are available.

Flow and thermal modeling of liquid metal in expanded microchannel heat sink

Liquid metal-based microchannel heat sinks (MCHSs) suffer from the low heat capacity of coolant, resulting in an excessive temperature rise of coolant and heat sink when dealing with high-power heat dissipation. In this paper, it was found that expanded space at the top of fins could distribute the heat inside microchannels, reducing the temperature rise of coolant and heat sink. The orthogonal experiments revealed that expanding the top space of channels yielded similar temperature reductions to changing the channel width. The flow and thermal modeling of expanded microchannel heat sink (E-MCHS) were analyzed by both using the 3-dimensional (3D) numerical simulation and the 1-dimensional (1D) thermal resistance model. The fin efficiency of E-MCHS was derived to improve the accuracy of the 1D thermal resistance model. The heat conduction of liquid metal in Z direction and the heat convection between the top surface of fins and the liquid metal could reduce the total thermal resistance (Rt). The above process was effective for microchannels with low channel aspect ratio, low mean velocity (Um) or long heat sink length. The maximum thermal resistance reduction in the example of this paper reached 36.0%. The expanded space endowed the heat sink with lower pressure, which might further reduce the pumping power (P). This rule was feasible both when fins were truncated (h_(2) < 0, h_(2) is the height of expanded channel for E-MCHS) and when over plate was raised (h_(2) > 0).

Optimisation of Thermal Comfort of Building in a Hot and Dry Tropical Climate: A Comparative Approach between Compressed Earth/Concrete Block Envelopes

Compressed earth blocks (CEB) are an alternative to cement blocks in the construction of wall masonry. However, the optimal architectural construction methods for adequate thermal comfort for occupants in hot and arid environments are not mastered. This article evaluates the influence of architectural and constructive modes of buildings made of CEB walls and concrete block walls, to optimize and compare their thermal comfort in the hot and dry tropical climate of Ouagadougou, Burkina Faso. Two identical pilot buildings whose envelopes are made of CEB and concrete blocks were monitored for this study. The thermal models of the pilot buildings were implemented in the SketchUp software using an extension of EnergyPlus. The models were empirically validated after calibration against measured thermal data from the buildings. The models were used to do a parametric analysis for optimization of the thermal performances by simulating plaster coatings on the exterior of walls, airtight openings and natural ventilation depending on external weather conditions. The results show that the CEB building displays 7016 hours of discomfort, equivalent to 80.1% of the time, and the concrete building displays 6948 hours of discomfort, equivalent to 79.3% of the time. The optimization by modifications reduced the discomfort to 2918 and 3125 hours respectively;i.e. equivalent to only 33.3% for the CEB building and 35.7% for the concrete building. More study should evaluate thermal optimizations in buildings in real time of usage such as residential buildings commonly used by the local middle class. The use of CEB as a construction material and passive means of improving thermal comfort is a suitable ecological and economical option to replace cementitious material.

Thermal Study and Modeling of the Cold Room of a Solar Adsoption Refrigerator

In this work, we are interested in the study of the thermal exchanges which take place at the evaporator of an adsorption refrigerator. Due to the cost of designing experimental devices and the impossibility of studying the influence of certain parameters experimentally, an alternative would be simulation. The aim is to provide a model for predicting the thermal behavior of the various elements in the cold room of an adsorption solar refrigerator. A dynamic modelling of the refrigerator taking into account fluid flow, heat and mass transfer phenomena in the cold room was made. The calculation code obtained using COMSOL 5.1 software makes it possible to analyze and study the influence of the various parameters on the performance of the system. In a second step, the theoretical results obtained were compared with the experimental results in order to validate the model. The analysis of the influence of the physical-thermal properties of the insulating material on the temperature of the chamber makes it possible to conclude that a material having a low density ρ, a low thermal conductivity λ and a low specific heat capacity offers better performance to the cold room. Better thermal insulation also implies having a reasonable insulation thickness.

Valve Dynamic and Thermal Cycle Model in Stepless Capacity Regulation for Reciprocating Compressor

The existing researches of stepless capacity regulation system by depressing the suction valve for reciprocation compressor always adopt hypothesis that the compressor valves are open or close instantaneously, the valve dynamic has not been taken account into thermal cycle computation, the influence of capacity regulation system on suction valves dynamic performance and cylinder thermal cycle operation has not been considered. This paper focuses on theoretical and experimental analysis of the valve dynamic and thermal cycle for reciprocating compressor in the situation of stepless capacity regulation. The valve dynamics equation, gas forces for normal and back flow, and the cylinder pressure varying with suction valve unloader moment during compression thermal cycle are discussed. A new valve dynamic model based on L-K real gas state equation for reciprocating compressor is first deduced to reduce the calculation errors induced by the ideal gas state equation. The variations of valve dynamic and cylinder pressure during part of compression stroke are calculated numerically. The calculation results reveal the non-normal thermal cycle and operation condition of compressor in stepless capacity regulation situation. The numerical simulation results of the valve dynamic and thermal cycle parameters are also verified by the stepless capacity regulation experiments in the type of 3L-10/8 reciprocating compressor. The experimental results agree with the numerical simulation results, which show that the theoretical models proposed are effective and high-precision. The proposed theoretical models build the theoretical foundation to design the real stepless capacity regulation system.

Spindle Thermal Error Optimization Modeling of a Five-axis Machine Tool

Aiming at the problem of low machining accu- racy and uncontrollable thermal errors of NC machine tools, spindle thermal error measurement, modeling and compensation of a two turntable five-axis machine tool are researched. Measurement experiment of heat sources and thermal errors are carried out, and GRA（grey relational analysis） method is introduced into the selection of tem- perature variables used for thermal error modeling. In order to analyze the influence of different heat sources on spindle thermal errors, an ANN （artificial neural network） model is presented, and ABC（artificial bee colony） algorithm is introduced to train the link weights of ANN, a new ABC- NN（Artificial bee colony-based neural network） modeling method is proposed and used in the prediction of spindle thermal errors. In order to test the prediction performance of ABC-NN model, an experiment system is developed, the prediction results of LSR （least squares regression）, ANN and ABC-NN are compared with the measurement results of spindle thermal errors. Experiment results show that the prediction accuracy of ABC-NN model is higher than LSR and ANN, and the residual error is smaller than 3 pm, the new modeling method is feasible. The proposed research provides instruction to compensate thermal errors and improve machining accuracy of NC machine tools.