Numerical Study and Optimization of CZTS-Based Thin-Film Solar Cell Structure with Different Novel Buffer-Layer Materials Using SCAPS-1D Software

This study explored the performances of CZTS-based thin-film solar cell with three novel buffer layer materials ZnS, CdS, and CdZnS, as well as with variation in thickness of buffer and absorber-layer, doping concentrations of absorber-layer material and operating temperature. Our aims focused to identify the most optimal thin-film solar cell structure that offers high efficiency and lower toxicity which are desirable for sustainable and eco-friendly energy sources globally. SCAPS-1D, widely used software for modeling and simulating solar cells, has been used and solar cell fundamental performance parameters such as open-circuited voltage (), short-circuited current density (), fill-factor() and efficiency() have been optimized in this study. Based on our simulation results, it was found that CZTS solar cell with Cd0.4Zn0.6S as buffer-layer offers the most optimal combination of high efficiency and lower toxicity in comparison to other structure investigated in our study. Although the efficiency of Cd0.4Zn0.6S, ZnS and CdS are comparable, Cd0.4Zn0.6S is preferable to use as buffer-layer for its non-toxic property. In addition, evaluation of performance as a function of buffer-layer thickness for Cd0.4Zn0.6S, ZnS and CdS showed that optimum buffer-layer thickness for Cd0.4Zn0.6S was in the range from 50 to 150nm while ZnS offered only 50 – 75 nm. Furthermore, the temperature dependence performance parameters evaluation revealed that it is better to operate solar cell at temperature 290K for stable operation with optimum performances. This study would provide valuable insights into design and optimization of nanotechnology-based solar energy technology for minimizing global energy crisis and developing eco-friendly energy sources sustainable and simultaneously.

Interface optimization and defects suppression via Na F introduction enable efficient flexible Sb_(2)Se_(3) thin-film solar cells

Sb_(2)Se_(3) with unique one-dimensional(1D) crystal structure exhibits exceptional deformation tolerance,demonstrating great application potential in flexible devices.However,the power conversion efficiency(PCE) of flexible Sb_(2)Se_(3) photovoltaic devices is temporarily limited by the complicated intrinsic defects and the undesirable contact interfaces.Herein,a high-quality Sb_(2)Se_(3) absorber layer with large crystal grains and benign [hkl] growth orientation can be first prepared on a Mo foil substrate.Then NaF intermediate layer is introduced between Mo and Sb_(2)Se_(3),which can further optimize the growth of Sb_(2)Se_(3)thin film.Moreover,positive Na ion diffusion enables it to dramatically lower barrier height at the back contact interface and passivate harmful defects at both bulk and heterojunction.As a result,the champion substrate structured Mo-foil/Mo/NaF/Sb_(2)Se_(3)/CdS/ITO/Ag flexible thin-film solar cell delivers an obviously higher efficiency of 8.03% and a record open-circuit voltage(V_(OC)) of 0.492 V.This flexible Sb_(2)Se_(3) device also exhibits excellent stability and flexibility to stand large bending radius and multiple bending times,as well as superior weak light photo-response with derived efficiency of 12.60%.This work presents an effective strategy to enhance the flexible Sb_(2)Se_(3) device performance and expand its potential photovoltaic applications.

Design of periodic metal-insulator-metal waveguide back structures for the enhancement of light absorption in thin-film solar cells

To increase the absorption in a thin layer of absorbing material （amorphous silicon, a-Si）, a light trapping design is presented. The designed structure incorporates periodic metal-insulator-metal waveguides to enhance the optical path length of light within the solar cells. The new design can result in broadband optical absorption enhancement not only for transverse magnetic （TM）-polarized light, but also for transverse electric （TE）-polarized light. No plasmonic modes can be excited in TE-polarization, but because of the coupling into the a-Si planar waveguide guiding modes and the diffraction of light by the bottom periodic structures into higher diffraction orders, the total absorption in the active region is also increased. The results from rigorous coupled wave analysis show that the overall optical absorption in the active layer can be greatly enhanced by up to 40%. The designed structures presented in this paper can be integrated with back contact technology to potentially produce high-efficiency thin-film solar cell devices.

Improvement of the Open Circuit Voltage of CZTSe Thin-Film Solar Cells by Surface Sulfurization Using SnS

The objective of this study is to find an effective method to improve Voc without Jsc loss for Cu2ZnSnSe4 （CZTSe） thin film solar cells, which have been fabricated by the one step co-evaporation technique. Surface sulfurization of CZTSe thin films is carried out by using one technique that does not utilize toxic H2S gas; a sequential evaporation of SnS after CZTSe deposition and the annealing of CZTSe thin films in selenium vapor. A Cu2ZnSn（S, Se）4 （CZTSSe） thin layer is grown on the surface of the CZTSe thin film after the annealing. The conversion efficiency of the completed device is improved due to the enhancement of Voc, which could be attributed to the formation of a hole-recombination barrier at the surface or the passivation of the surface and grain boundary by S incorporation.

Enhanced efficiency of the Sb_(2)Se_(3)thin-film solar cell by the anode passivation using an organic small molecular of TCTA

Antimony selenide(Sb_(2)Se_(3))is an emerging solar cell material.Here,we demonstrate that an organic small molecule of 4,4',4''-tris(carbazol-9-yl)-triphenylamine(TCTA)can efficiently passivate the anode interface of the Sb_(2)Se_(3)solar cell.We fabricated the device by the vacuum thermal evaporation,and took ITO/TCTA(3.0 nm)/Sb_(2)Se_(3)(50 nm)/C60(5.0 nm)/Alq3(3.0 nm)/Al as the device architecture,where Alq3 is the tris(8-hydroxyquinolinato)aluminum.By introducing a TCTA layer,the open-circuit voltage is raised from 0.36 to 0.42 V,and the power conversion efficiency is significantly improved from 3.2%to 4.3%.The TCTA layer not only inhibits the chemical reaction between the ITO and Sb_(2)Se_(3)during the annealing process but it also blocks the electron diffusion from Sb_(2)Se_(3)to ITO anode.The enhanced performance is mainly attributed to the suppression of the charge recombination at the anode interface.

Numerical simulation of a triple-junction thin-film solar cell based on μc-Si_(1-x)Ge_x :H

In this paper, a-Si：H/a-SiGe：H/μc-SiGe：H triple-junction solar cell structure is proposed. By the analyses of mi- croelectronic and photonic structures （AMPS-1D） and our TRJ-F/TRJ-M/TRJ-B tunneling-recombination junction （TRJ） model, the most preferably combined bandgap for this structure is found to be 1.85 eV/1.50 eV/1.0 eV. Using more realistic material properties, optimized thickness combination is investigated. Along this direction, a-Si：H/a-SiGe：H/μc-SiGe：H triple cell with an initial efficiency of 12.09% （Voc = 2.03 V, FF = 0.69, Jsc = 8.63 mA/cm^2, area = 1 cm^2） is achieved in our laboratory.

Optimizing a Single-Absorption-Layer Thin-Film Solar Cell1 Model to Achieve 31% Efficiency

This research builds upon the authors’ previous work that introduced and modeled a novel Gallium-Arsenide, Emitterless, Back-surface Alternating Contact (GaAs-EBAC) thin-film solar cell to achieve >30% power conversion efficiency. Key design parameters are optimized under an Air-Mass (AM) 1.5 spectrum to improve performance and approach the 33.5% theoretical efficiency limit. A second optimization is performed under an AM0 spectrum to examine the cell’s potential for space applications. This research demonstrates the feasibility and potential of a new thin-film solar cell design for terrestrial and space applications. Results suggest that the straight-forward design may be an inexpensive alternative to multi-junction solar cells.

Double-layer indium doped zinc oxide for silicon thin-film solar cell prepared by ultrasonic spray pyrolysis

Indium doped zinc oxide （ZnO：In） thin films were prepared by ultrasonic spray pyrolysis on corning eagle 2000 glass substrate. 1 and 2 at.% indium doped single-layer ZnO：In thin films with different amounts of acetic acid added in the initial solution were fabricated. The 1 at.% indium doped single-layers have triangle grains. The 2 at.% indium doped single-layer with 0.18 acetic acid adding has the resistivity of 6.82 × 10^-3 Ω. cm and particle grains. The doublelayers structure is designed to fabricate the ZnO：In thin film with low resistivity （2.58 × 10^-3 Ω. cm） and good surface morphology. It is found that the surface morphology of the double-layer ZnO：In film strongly depends on the substratelayer, and the second-layer plays a large part in the resistivity of the doublewlayer ZnO：In thin film. Both total and direct transmittances of the double-layer ZnO：In film are above 80% in the visible light region. Single junction a-Si：H solar cell based on the double-layer ZnO：In as front electrode is also investigated.

β-FeSi_2 as the bottom absorber of triple-junction thin-film solar cells: A numerical study

Using β-FeSi2 as the bottom absorber of triple-junction thin-film solar cells is investigated by a numerical method for widening the long-wave spectral response. The presented results show that the β-FeSi2 subcell can contribute 0.273 V of open-circuit voltage to the a-Si/μc-Si/β-FeSi2 triple-junction thin-film solar cell. The optimized absorber thicknesses for a- Si, μ-Si, and/3-FeSi2 subcells are 260 nm, 900 nm, and 40 nm, respectively. In addition, the temperature coefficient of the conversion efficiency of the a-Si/μc-Si//3-FeSi2 cell is -0.308 %/K, whose absolute value is only greater than that of the a-Si subcell. This result indicates that the a-Si/μc-Si/β-FeSi2 triple-junction solar cell has a good temperature coefficient. As a result, using β-FeSi2 as the bottom absorber can improve the thin-film solar cell performance, and the a-Si/μc-Si/β-FeSi2 triple-junction solar cell is a promising structure configuration for improving the solar cell efficiency.

Non-ionizing energy loss calculations for modeling electron-induced degradation of Cu(In,Ga)Se_2 thin-film solar cells

The lowest energies which make Cu,In,Ga,and Se atoms composing Cu（In,Ga）Se_2（CIGS） material displaced from their lattice sites are evaluated,respectively.The non-ionizing energy loss（NIEL） for electron in CIGS material is calculated analytically using the Mott differential cross section.The relation of the introduction rate（k） of the recombination centers to NIEL is modified,then the values of k at different electron energies are calculated.Degradation modeling of CIGS thin-film solar cells irradiated with various-energy electrons is performed according to the characterization of solar cells and the recombination centers.The validity of the modeling approach is verified by comparison with the experimental data.

Back contact interfacial modification mechanism in highly-efficient antimony selenide thin-film solar cells

Antimony selenide(Sb_(2)Se_(3))is a potential photovoltaic(PV)material for next-generation solar cells and has achieved great development in the last several years.The properties of Sb_(2)Se_(3)absorber and back contact influence the PV performances of Sb_(2)Se_(3)solar cells.Hence,optimization of back contact characteristics and absorber orientation are crucial steps in raising the power conversion efficiency(PCE)of Sb_(2)Se_(3)solar cells.In this work,MoO2was introduced as an intermediate layer(IL)in Sb_(2)Se_(3)solar cells,and comparative investigations were conducted.The growth of(211)-oriented Sb_(2)Se_(3)with large grains was facilitated by introducing the MoO2IL with suitable thickness.The MoO2IL substantially lowered the back contact barrier and prevented the formation of voids at the back contact,which reduced the thickness of the MoSe2interface layer,inhibited carrier recombination,and minimized bulk and interfacial defects in devices.Subsequently,significant optimization enhanced the open-circuit voltage(VOC)of solar cells from 0.481 V to 0.487 V,short-circuit current density(JSC)from 23.81 m A/cm^(2)to 29.29 m A/cm^(2),and fill factor from 50.28%to 57.10%,which boosted the PCE from 5.75%to 8.14%.

Investigation of Ag(Ga,In)Se_(2)as thin-film solar cell absorbers:A first-principles study

Using first-principles calculations,the structural,electronic,and defect properties of AgInSe_(2)(AIS),AgGaSe_(2)(AGS),and their alloys(AIGS)are systematically studied and compared with their Cu counterparts as potential candidates for thin-film solar cell absorbers.The bandgap energies of AIS(1.24 eV)and AGS(1.84 eV)are larger than their Cu counterparts,despite their larger lattice parameters.According to the Shockley-Queisser theory,AIS or AIGS could be more suitable for solar-cell-absorber materials than their Cu counterparts.However,after investigating the band structures and intrinsic defect properties of AIS and AGS,we find that,(i)AIS and AGS have large negative crystal field splitting,thus low density of states near the valence band maximum(VBM);(ii)similar to the Cu counterparts,Ag vacancy(V_(Ag))is the main hole-carrier provider,while In_(Ag)(or Ga_(Ag))serves as the hole-carrier killer in p-type AIS(or AGS).However,because the positions of theVBM and conduction band minimum of AIS(or AGS)are lower than those of Cu In Se_(2)(CIS)[or Cu Ga Se_(2)(CGS)],the compensation of the p-type doping in AIS(or AGS)is more severe.Thus,the p-type doping of AIS(or AIGS)is more difficult than that of CIS(or CIGS),which is consistent with the doping limit rule.To improve the p-type doping of the AIS(or AIGS)as the solar-cell absorber,thus,improve the power conversion efficiency(PCE),the Ag-rich/(In,Ga)-poor/Se-rich growth condition is preferred.Alloy engineering of AIS with AGS can enhance the PCE because it can tune the bandgap energy of the absorber and band alignment at the absorber/buffer interface.More importantly,we suggest that for AIS(or AIGS)solar cell,the traditional buffer material of Cd S is not suitable anymore due to the large conduction band offset between AIS and Cd S.A new buffer layer material with a lower conduction band edge is necessary for better electron transport in AIS(or AIGS)solar cell.

First-principles study of defect control in thin-film solar cell materials

A solar cell is a photovoltaic device that converts solar radiation energy to electrical energy, which plays a leading role in alleviating global energy shortages and decreasing air pollution levels typical of conventional fossil fuels. To render solar cells more efficient, high visible-light absorption rates and excellent carrier transport properties are required to generate high carrier levels and high output voltage. Hence, the core material, i.e., the absorption layer, should have an appropriate direct band gap and be effectively doped by both p-and n-types with minimal carrier traps and recombination centers. Consequently, defect properties of absorbers are critical in determining solar cell efficiency. In this work, we review recent first-principles studies of defect properties and engineering in four representative thin-film solar cells, namely CdTe, Cu(In,Ga)Se2, Cu2ZnSnS4, and halide perovskites. The focal points include basic electronic and defect properties, existing problems, and possible solutions in engineering defect properties of those materials to optimize solar cell efficiency.

A process study of high-quality Zn(O,S)thin-film fabrication for thin-film solar cells

The Zn(O,S)thin film is considered a most promising candidate for a cadmium-free buffer layer of the Cu(In,Ga)Se_(2)(CIGS)thin-film solar cell due to its advantages of optical responses in the short-wavelength region and adjustable bandgap.In this paper,the thin-film growth mechanism and process optimization of Zn(O,S)films fabricated using the chemical bath deposition method are sys-tematically investigated.The thickness and quality of Zn(O,S)films were found to be strongly affected by the concentration variation of the precursor chemicals.It was also revealed that different surface morphologies of Zn(O,S)films would appear if the reaction time were changed and,subsequently,the optimum reaction time was defined.The film-growth curve suggested that the growth rate varied linearly with the deposition temperature and some defects appeared when the temperature was too high.In addition,to further improve the film quality,an effective post-treatment approach was proposed and the experimental results showed that the microstructure of the Zn(O,S)thin film was improved by an ammonia etching process followed by an annealing process.For com-parison purposes,both Zn(O,S)-based and CdS-based devices were fabricated and characterized.The device with a Zn(O,S)-CIGS solar cell after post-treatment showed near conversion efficiency comparable to that of the device with the CdS-CIGS cell.

High performance wide bandgap perovskite solar cell with low V_(OC) deficit less than 0.4 V

Wide bandgap perovskite solar cells(PSCs)have attracted significant attention because they can be applied to the top cells of tandem solar cells.However,high open-circuit voltage(V_(OC))deficit(>0.4 V)result from poor crystallization and high non-radiative recombination losses become a serious limitation in the pursuit of high performance.Here,the relevance between different Pbl_(2)proportions and performance parameters are revealed through analysis of surface morphology,residual stress,and photostability.The increase of Pbl_(2)proportion promotes crystal growth and reduces the work function of the perovskite film surface and promotes the energy level alignment with the carrier transport layer,which decreased the V_(OC)deficit.However,residual PbI_(2)exacerbated the stress level of perovskite film,and the resulting lattice disorder deteriorated the photostability of the device.Ultimately,after the synergistic passivation of residual PbI_(2)and PEAI,the V_(OC)achieves 1.266 V and V_(OC)deficit is less than 0.4 V,the record value in wide bandgap PSCs.

Toluene Processed All-Polymer Solar Cells with 18%Efficiency and Enhanced Stability Enabled by Solid Additive:Comparison Between Sequential-Processing and Blend-Casting

The emergence of polymerized small molecule acceptors(PSMAs)has significantly improved the performance of all-polymer solar cells(all-PSCs).However,the pace of device engineering lacks behind that of materials development,so that a majority of the PSMAs have not fulfilled their potentials.Furthermore,most high-performance all-PSCs rely on the use of chloroform as the processing solvent.For instance,the recent highperformance PSMA,named PJ1-γ,with high LUMO,and HOMO levels,could only achieve a PCE of 16.1%with a high-energy-level donor(JD40)using chloroform.Herein,we present a methodology combining sequential processing(SqP)with the addition of 0.5%wt PC_(71)BM as a solid additive(SA)to achieve an impressive efficiency of 18.0%for all-PSCs processed from toluene,an aromatic hydrocarbon solvent.Compared to the conventional blend-casting(BC)method whose best efficiency(16.7%)could only be achieved using chloroform,the SqP method significantly boosted the device efficiency using toluene as the processing solvent.In addition,the donor we employ is the classic PM6 that has deeper energy levels than JD40,which provides low energy loss for the device.We compare the results with another PSMA(PYF-T-o)with the same method.Finally,an improved photostability of the SqP devices with the incorporation of SA is demonstrated.

Step‑by‑Step Modulation of Crystalline Features and Exciton Kinetics for 19.2%Efficiency Ortho‑Xylene Processed Organic Solar Cells

With plenty of popular and effective ternary organic solar cells(OSCs)construction strategies proposed and applied,its power conversion efficiencies(PCEs)have come to a new level of over 19%in single-junction devices.However,previous studies are heavily based in chloroform(CF)leaving behind substantial knowledge deficiencies in understanding the influence of solvent choice when introducing a third component.Herein,we present a case where a newly designed asymmetric small molecular acceptor using fluoro-methoxylated end-group modification strategy,named BTP-BO-3FO with enlarged bandgap,brings different morphological evolution and performance improvement effect on host system PM6:BTP-eC9,processed by CF and ortho-xylene(o-XY).With detailed analyses supported by a series of experiments,the best PCE of 19.24%for green solvent-processed OSCs is found to be a fruit of finely tuned crystalline ordering and general aggregation motif,which furthermore nourishes a favorable charge generation and recombination behavior.Likewise,over 19%PCE can be achieved by replacing spin-coating with blade coating for active layer deposition.This work focuses on understanding the commonly met yet frequently ignored issues when building ternary blends to demonstrate cutting-edge device performance,hence,will be instructive to other ternary OSC works in the future.

Manipulating the Macroscopic and Microscopic Morphology of Large-Area Gravure-Printed ZnO Films for High-Performance Flexible Organic Solar Cells

Gravure printing is a promising large-scale fabrication method for flexible organic solar cells(FOSCs)because it is compatible with two-dimension patternable roll-to-roll fabrication.However,the unsuitable rheological property of ZnO nanoinks resulted in unevenness and looseness of the gravure-printed ZnO interfacial layer.Here we propose a strategy to manipulate the macroscopic and microscopic of the gravure-printed ZnO films through using mixed solvent and poly(vinylpyrrolidone)(PVP)additive.The regulation of drying speed effectively manipulates the droplets fusion and leveling process and eliminates the printing ribbing structure in the macroscopic morphology.The additive of PVP effectively regulates the rheological property and improves the microscopic compactness of the films.Following this method,large-area ZnO∶PVP films(28×9 cm^(2))with excellent uniformity,compactness,conductivity,and bending durability were fabricated.The power conversion efficiencies of FOSCs with gravure-printed AgNWs and ZnO∶PVP films reached 14.34%and 17.07%for the 1 cm^(2)PM6:Y6 and PM6∶L8-BO flexible devices.The efficiency of 17.07%is the highest value to date for the 1 cm^(2)FOSCs.The use of mixed solvent and PVP addition also significantly enlarged the printing window of ZnO ink,ensuring high-quality printed thin films with thicknesses varying from 30 to 100 nm.

High-Quality van der Waals Epitaxial CsPbBr_(3)Film Grown on Monolayer Graphene Covered TiO_(2)for High-Performance Solar Cells

Two-dimensional materials have been widely used to tune the growth and energy-level alignment of perovskites.However,their incomplete passivation and chaotic usage amounts are not conducive to the preparation of highquality perovskite films.Herein,we succeeded in obtaining higher-quality CsPbBr_(3)films by introducing large-area monolayer graphene as a stable physical overlay on top of TiO_(2)substrates.Benefiting from the inert and atomic smooth graphene surface,the CsPbBr_(3)film grown on top by the van der Waal epitaxy has higher crystallinity,improved(100)orientation,and an average domain size of up to 1.22μm.Meanwhile,a strong downward band bending is observed at the graphene/perovskite interface,improving the electron extraction to the electron transport layers(ETL).As a result,perovskite film grown on graphene has lower photoluminescence(PL)intensity,shorter carrier lifetime,and fewer defects.Finally,a photovoltaic device based on epitaxy CsPbBr_(3)film is fabricated,exhibiting power conversion efficiency(PCE)of up to 10.64%and stability over 2000 h in the air.

Accelerated Sequential Deposition Reaction via Crystal Orientation Engineering for Low-Temperature,High-Efficiency Carbon-Electrode CsPbBr_(3) Solar Cells

Low-temperature,ambient processing of high-quality CsPbBr_(3)films is demanded for scalable production of efficient,low-cost carbon-electrode perovskite solar cells(PSCs).Herein,we demonstrate a crystal orientation engineering strategy of PbBr_(2)precursor film to accelerate its reaction with CsBr precursor during two-step sequential deposition of CsPbBr_(3)films.Such a novel strategy is proceeded by adding CsBr species into PbBr_(2)precursor,which can tailor the preferred crystal orientation of PbBr_(2)film from[020]into[031],with CsBr additive staying in the film as CsPb_(2)Br_(5)phase.Theoretical calculations show that the reaction energy barrier of(031)planes of PbBr_(2)with CsBr is lower about 2.28 eV than that of(O2O)planes.Therefore,CsPbBr_(3)films with full coverage,high purity,high crystallinity,micro-sized grains can be obtained at a low temperature of 150℃.Carbon-electrode PSCs with these desired CsPbBr_(3)films yield the record-high efficiency of 10.27%coupled with excellent operation stability.Meanwhile,the 1 cm^(2)area one with the superior efficiency of 8.00%as well as the flexible one with the champion efficiency of 8.27%and excellent mechanical bending characteristics are also achieved.