Development of a toroidal soft x-ray imaging system and application for investigating three-dimensional plasma on J-TEXT

A toroidal soft x-ray imaging(T-SXRI)system has been developed to investigate threedimensional(3D)plasma physics on J-TEXT.This T-SXRI system consists of three sets of SXR arrays.Two sets are newly developed and located on the vacuum chamber wall at toroidal positionsφof 126.4°and 272.6°,respectively,while one set was established previously atφ=65.50.Each set of SXR arrays consists of three arrays viewing the plasma poloidally,and hence can be used separately to obtain SXR images via the tomographic method.The sawtooth precursor oscillations are measured by T-SXRI,and the corresponding images of perturbative SXR signals are successfully reconstructed at these three toroidal positions,hence providing measurement of the 3D structure of precursor oscillations.The observed 3D structure is consistent with the helical structure of the m/n=1/1 mode.The experimental observation confirms that the T-SXRI system is able to observe 3D structures in the J-TEXT plasma.

Quantitative measurement of the charge carrier concentration using dielectric force microscopy

The charge carrier concentration profile is a critical factor that determines semiconducting material properties and device performance.Dielectric force microscopy(DFM)has been previously developed to map charge carrier concentrations with nanometer-scale spatial resolution.However,it is challenging to quantitatively obtain the charge carrier concentration,since the dielectric force is also affected by the mobility.Here,we quantitative measured the charge carrier concentration at the saturation mobility regime via the rectification effect-dependent gating ratio of DFM.By measuring a series of n-type GaAs and GaN thin films with mobility in the saturation regime,we confirmed the decreased DFM-measured gating ratio with increasing electron concentration.Combined with numerical simulation to calibrate the tip–sample geometry-induced systematic error,the quantitative correlation between the DFM-measured gating ratio and the electron concentration has been established,where the extracted electron concentration presents high accuracy in the range of 4×10^(16)–1×10^(18)cm^(-3).We expect the quantitative DFM to find broad applications in characterizing the charge carrier transport properties of various semiconducting materials and devices.

An experimental study:Integration device of Fiber Bragg grating and reinforced concrete beam for measuring debris flow impact force

The impact effect of boulder within debris flow is the key factor contributing to peak impact as well as to the failure of debris flow control work. So accurate measuring and calculating the impact force of debris flow can ensure the engineering design strength. However, limited to the existing laboratory conditions and piezoelectric sensor performance, it is impossible, based on the conventional measurements, to devise a computing method for expressing a reliable boulder impact force. This paper has therefore designed a new measurement device according to the method of integrating Fiber Bragg grating(FBG) and reinforced concrete composite beam(RCB) for measuring the impact force of debris flows, i.e. mounting FBG on the axially stressed steel bar in the composite beam at regular intervals to monitor the steel strain. RCB plays the role of contacting debris flow and protecting FBG sensors. Taking this new device as the experimental object, drop testing is designed for simulating and reflecting the boulder impact force. In a series of impacting tests, the relationship between the peak dynamic strain value of the steel bar and the impact force is analyzed, and based on which, an inversion model that uses the steel bar strain as the independent variable is established for calculating the boulder impact force.The experimental results show that this new inversion model can determine the impact force value and its acting position with a system error of 18.1%, which can provide an experimental foundation for measuring the impact force of boulders within the debris flow by the new FBG-based device.

AN OPTICAL FIBRE SENSOR BASED CUTTING FORCE MEASURING DEVICE

A cutting force measuring device is developed which is composed of a common tool shank and an optical fibre sensor. The sensor is mounted at the rear of the shank and the deformation of the shank caused by cutting force is detected as the measurement of cutting force. The device possesses good adaptability to workshop conditions as well as satisfying static and dynamic performances.

A New Study to Compensate Dynamic Measuring Error of Serial Multiple Degree of Freedom（DOF） Strain Gauge Force Sensor

ＡＮｅｗＳｔｕｄｙｔｏＣｏｍｐｅｎｓａｔｅＤｙｎａｍｉｃＭｅａｓｕｒｉｎｇＥｒｒｏｒｏｆＳｅｒｉａｌＭｕｌｔｉｐｌｅＤｅｇｒｅｅｏｆＦｒｅｅｄｏｍ（ＤＯＦ）ＳｔｒａｉｎＧａｕｇｅＦｏｒｃｅＳｅｎｓｏｒＣＡＩＨａｉｎａｎ；ＪＩＡＮＧＺｕｏｍｉｎ；ＱＩＡ...

Design and research of measuring system of clamping force of hemostats

Reliability of medical instruments such as hemostats is extremely important because these instruments are used in patients who are in critical condition. Clamping force of hemostats, as an important parameter of hemostats, should be detected. However, it could not be tested directly. In order to test it, a testing system has been put forward. The system is comprised of sensor, acquisition card, and three-way tap and so on. This system is controlled by a computer. The testing system has been proved to be effective in testing the clamping force of hemostats.

Behavior of traditional concrete dams and three-dimensional printed concrete dams under the debris flow impact

This study investigated the resilience of traditional concrete dams compared to 3D printed concrete dams(3DPC)when subjected to debris flow.Three types of dams,namely check dams,arch dams,and curve dams,were numerically analyzed using a three-dimensional Coupled Eulerian-Lagrangian(CEL)methodology.The research focused on critical factors such as impact force and viscous energy dissipation to compare dam performance.Additionally,the study examined the printing and service phases of 3DPC models,determining potential failure modes and analyzing printing parameters.The results demonstrated that 3DPC dams outperformed traditional concrete dams,with filament deposition orientation,perpendicular to the debris flow direction,identified as a pivotal factor.Infill percentage and pattern were also found to influence the behavior of 3DPC models.Notably,curved dams exhibited superior performance based on dam geometry.These findings have significant potential for advancing the development of resilient dam structures capable of withstanding debris flow impacts.

Multi-objective strategy to optimize dithering technique for high-quality three-dimensional shape measurement

Dithering optimization techniques can be divided into the phase-optimized technique and the intensity-optimized technique. The problem with the former is the poor sensitivity to various defocusing amounts, and the problem with the latter is that it cannot enhance phase quality directly nor efficiently. In this paper, we present a multi-objective optimization framework for three-dimensional(3D) measurement by utilizing binary defocusing technique. Moreover, a binary patch optimization technique is used to solve the time-consuming issue of genetic algorithm. It is demonstrated that the presented technique consistently obtains significant phase performance improvement under various defocusing amounts.

Three-Dimensional Analytical Modeling of Axial-Flux Permanent Magnet Drivers

In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare comprehensively considered, and the governing equations are solved bysimplifying the boundary conditions. The axial magnetization of the sectorshapedpermanent magnets is accurately described in an algebraic form bythe parameters, which makes the physical meaning more explicit than thepurely mathematical expression in general series forms. The parameters of theBessel function are determined simply and the magnetic field distribution ofpermanent magnets and the air-gap is solved. Furthermore, the field solutionsare completely analytical, which provides convenience and satisfactoryaccuracy for modeling a series of electromagnetic performance parameters,such as the axial electromagnetic force density, axial electromagnetic force,and electromagnetic torque. The correctness and accuracy of the analyticalmodels are fully verified by three-dimensional finite element simulations and a15 kW prototype and the results of calculations, simulations, and experimentsunder three methods are highly consistent. The influence of several designparameters on magnetic field distribution and performance is studied and discussed.The results indicate that the modeling method proposed in this papercan calculate the magnetic field distribution and performance accurately andrapidly, which affords an important reference for the design and optimizationof axial-flux permanent magnet drivers.

Measurement of forces generated during distraction of growing-rods in early onset scoliosis

AIM: To measure the forces applied during distraction of growing-rods in early onset scoliosis(EOS), aimed at developing a motorized elongation device.METHODS: A consecutive series of measurements were carried out to analyze the forces applied by the surgeon during distraction of single growing-rods in 10 patients affected by EOS(mean age 8.3 years; range 6 to 10 years) undergoing the first distraction 6 months following implantation of the rods. For each measurement, output from the transducer of a dedicated pair of distraction calipers was recorded at zero load status and at every 1 mm of distraction, up to a maximum of 12 mm for each of the two connected rods.RESULTS: Twenty measurements were obtained showing a linear increase of the load with increasing distraction, with a mean peak force of 485 N at 12 mm distraction and a single reading over 500 N. We did not observe bone fractures or ligament disruptions during or after rod elongations. There was one case of superficial wound infection in the cohort.CONCLUSION: The safe peak force carrying capacity of a motorized device for distraction of growing-rods is 500 N.

Evaluating the contribution of satellite measurements to the reconstruction of three-dimensional ocean temperature fields in combination with Argo profiles

Assimilation systems absorb both satellite measurements and Argo observations.This assimilation is essential to diagnose and evaluate the contribution from each type of data to the reconstructed analysis,allowing for better configuration of assimilation parameters.To achieve this,two comparative reconstruction schemes were designed under the optimal interpolation framework.Using a static scheme,an in situ-only field of ocean temperature was derived by correcting climatology with only Argo profiles.Through a dynamic scheme,a synthetic field was first derived from only satellite sea surface height and sea surface temperature measurements through vertical projection,and then a combined field was reconstructed by correcting the synthetic field with in situ profiles.For both schemes,a diagnostic iterative method was performed to optimize the background and observation error covariance statics.The root mean square difference(RMSD)of the in situ-only field,synthetic field and combined field were analyzed toward assimilated observations and independent observations,respectively.The rationale behind the distribution of RMSD was discussed using the following diagnostics:(1)The synthetic field has a smaller RMSD within the global mixed layer and extratropical deep waters,as in the Northwest Pacific Ocean;this is controlled by the explained variance of the vertical surface-underwater regression that reflects the ocean upper mixing and interior baroclinicity.(2)The in situ-only field has a smaller RMSD in the tropical upper layer and at midlatitudes;this is determined by the actual noise-to-signal ratio of ocean temperature.(3)The satellite observations make a more significant contribution to the analysis toward independent observations in the extratropics;this is determined by both the geographical feature of the synthetic field RMSD(smaller at depth in the extratropics)and that of the covariance correlation scales(smaller in the extratropics).

Environmental temperature effect on dimensional measurements of atomic force microscopy

Atomic force microscopy(AFM)is increasingly being used as a fundamental tool for dimensional measurements at the nanoscale in the laboratory and in industry.Since the environmental temperature is not controlled in many measurements,or is even varied on purpose,quantification of its effects on AFM dimensional measurements is needed.In this paper,the influences of the temperature in the entire environment of the AFM(excluding only the controller and computer)and that in the local environment around the tip–sample are investigated.The results show that lateral dimensional measurements are affected mainly by the entire environmental temperature.However,vertical measurements are influenced by the temperature of both the entire environment and the local environment.The effects become significant for temperatures higher than some threshold,here between 35 and 40 XC.

Wheel/rail-force–based maintenance interval extension of the C80 series wagon

Purpose–This study aims to introduce the achievements and benefits of applying wheel/rail-force–based maintenance interval extension of the C80 series wagon in China.Design/methodology/approach–Chinese wagons’existing maintenance strategy had left a certain safety margin for the characteristics of widely running range,unstable service environment and submission to transportation organization requirements.To reduce maintenance costs,China railway(CR)has attempted to extend the maintenance interval since 2020.The maintenance cycle of C80 series heavy haul wagons is extended by three months(no stable routing)or 50,000 km(regular routing).However,in the meantime,the alarming rate of the running state,a key index to reflect the severe degree of hunting stability,by the train performance detection system(TPDS)for the C80 series heavy haul wagons has increased significantly.Findings–The present paper addresses a big data statistical way to evaluate the risk of allowing the C80 series heavy haul wagons to remain in operation longer than stipulated by the maintenance interval initial set.Through the maintenance and wayside-detectordata,whichis divided intothreestages,the extension period(three months),the current maintenance period and the previous maintenance period,this method reveals the alarming rate of hunting was correlated with maintenance interval.The maintainability of wagons will be achieved by utilizing wagon performance degradation modeling with the state of the wheelset and the often-contact side bearing.This paper also proposes a statistical model to return to the average safety level of the previous maintenance period’s baseline through correct alarming thresholds for unplanned corrective maintenance.Originality/value–The paper proposes an approach to reduce safety risk due to maintenance interval extension by effective maintenance program.The results are expected to help the railway company make the optimal solution to balance safety and the economy.

Quality assessment of friction-stir-welded aluminum alloy welds via three-dimensional force signals

An online detection technology must be developed for realizing the real-time control of friction stir welding.In this study,the three-dimensional force exerted on a material during friction stir welding was collected synchronously and the relationship between the forces and welding quality was investigated.The results indicated that the fluctuation period of the traverse force was equal to that of the lateral force during the stable welding stage.The phase difference between two horizontal forces wasπ/2.The values of the horizontal forces increased with welding speed,whereas their amplitudes remained the same.The proposed force model showed that the traverse and lateral forces conformed to an elliptical curve,and this result was consistent with the behavior of the measured data.The variational mode decomposition was used to process the plunge force.The intrinsic mode function that represented the real fluctuation in the plunge force varied at the same frequency as the spindle rotational speed.When tunnel defects occurred,the fluctuation period features were consistent with those obtained during normal welding,whereas the ratio parameter defined in this study increased significantly.

An Application of Force Sensor to Impact Measurement

ＡｎＡｐｐｌｉｃａｔｉｏｎｏｆＦｏｒｃｅＳｅｎｓｏｒｔｏＩｍｐａｃｔＭｅａｓｕｒｅｍｅｎｔ￥（李邦宜）（邓樱）（王莉）（申杰ＬＩＢａｎｇｙｉ；ＤＥＮＧＹｉｎｇ；ＷＡＮＧＬｉ；ＳＨＥＮＪｉｅ（ＭｅａｓｕｒｅｍｅｎｔＣｅｎｔｅｒ，ＨａｒｂｉｎＩｎｓｔｉｔ...

Analysis of Photoelectric Hybridization Measurement on Shearing Force for Flat Shearer

This paper introduces a kind of photoelectric hybridization measuring process.Owing to the characteristics of the compact form of shearing equipment to be analyzed and the connecting rod existing in two directional stress state during operation etc.,it is hard to obtain results by means of single electrical testing process.For this reason,this paper derives a group of calculation formulas of hybridization measuring process through comprehensive discussion of photoelectric analysis and electrical testing theories,thus providing an analytical method for actual measurement of complex engineering problems.

A method for phase reconstruction in optical three-dimensional shape measurement

In optical three-dimensional shape measurement, a method of improving the measurement precision for phase reconstruction without phase unwrapping is analyzed in detail. Intensities of any five consecutive pixels that lie in the x-axis direction of the phase domain are given. Partial derivatives of the phase function in the x- and y-axis directions are obtained with a phase-shifting mechanism, the origin of which is analysed. Furthermore, to avoid phase unwrapping in the phase reconstruction, we derive the gradient of the phase function and perform a two-dimensional integral along the x- and y-axis directions. The reconstructed phase can be obtained directly by performing numerical integration, and thus it is of great convenience for phase reconstruction. Finally, the results of numerical simulations and practical experiments verify the correctness of the proposed method.

A fast and precise three-dimensional measurement system based on multiple parallel line lasers

This paper conducts a trade-off between efficiency and accuracy of three-dimensional(3 D)shape measurement based on the triangulation principle,and introduces a flying and precise 3 D shape measurement method based on multiple parallel line lasers.Firstly,we establish the measurement model of the multiple parallel line lasers system,and introduce the concept that multiple base planes can help to deduce the unified formula of the measurement system and are used in simplifying the process of the calibration.Then,the constraint of the line spatial frequency,which maximizes the measurement efficiency while ensuring accuracy,is determined according to the height distribution of the object.Secondly,the simulation analyzing the variation of the systemic resolution quantitatively under the circumstance of a set of specific parameters is performed,which provides a fundamental thesis for option of the four system parameters.Thirdly,for the application of the precision measurement in the industrial field,additional profiles are acquired to improve the lateral resolution by applying a motor to scan the 3 D surface.Finally,compared with the line laser,the experimental study shows that the present method of obtaining 41220 points per frame improves the measurement efficiency.Furthermore,the accuracy and the process of the calibration are advanced in comparison with the existing multiple-line laser and the structured light makes an accuracy better than 0.22 mm at a distance of 956.02 mm.

Diameters and form of skull base foramen ovale measured by three-dimensional spiral CT thin-slice scan in healthy adults

BACKGROUND： The accurate measurements of various data of the bone diameters of foramen ovale of living person can change the methods of puncturing trigeminal gasserian ganglion via foramen ovale for treating trifacial neuralgia from the experience of puncture operator only to puncture by taking the objective data of measurement as the evidence, which is good for improving the accuracy of puncturing trigeminal ganglion and reducing side effects. OBJECTIVE ： To observe the forms of foramen ovales in healthy adults displayed by volume rendering and multi-planar reconstruction after three-dimensional spiral CT thin-slice scan of skull base, and measure the longitudinal diameter and transverse diameter. DESIGN ： A repetitive observation and measurement SETTINGS ： Department of Neurosurgery and Department of Medical Imaging, Foshan Hospital of Traditional Chinese Medicine. PARTICIPANTS： Fifty healthy adults （100 sides）, who were examined with three-dimensional spiral CT scan, were randomly selected from the Department of Medical Imaging, Foshan Hospital of Traditional Chinese Medicine from January 2005 to January 2006, including 26 males and 24 females, aged 25-68 years with an average of 48 years old. They were all informed and agreed with the examination. METHODS ： The subjects were examined with the Philips 16-slice spiral CT-Mx 8000 IDT CT apparatus （Philips Company, Holland）, the scanning ranged from 2 cm below the canthomeatal line to the level of suprasellar cistem. The width of collimator was 0.75 mm, pitch was 0.663; tube current was 350 mA, voltage was 120 kV, resolution was 512×512 matrix; slice thickness of reconstruction was 1 mm, and interval was 0.5 mm. After the three-dimensional spiral CT thin-slice scan of skull base, the image post-processing techniques including volume rendering and multi-planar reconstruction were applied to observe the forms of foramen ovales, and measure the size, longitudinal diameter and transverse diameter of the foramen ovales. The figures of the foramen ovales were drawn with mouse along the boundary of bone porous margin and soft tissue. According to the indications, the diameters were measured with computer to observe the forms of foramen ovales. MAIN OUTCOME MEASURES ： The longitudinal diameter, transverse diameter and form of foramen ovales were observed. RESULTS： All the 50 healthy adults （100 sides） were involved in the analysis of results. （1） It was observed in the volume rendering images that foramen ovales had four forms of oval shape （77 sides）, kidney shape （12 sides）, round shape （7 sides）, ribbon shape （4 sides）. （2） The longitudinal diameters of left and right foramen ovales were （7.67±1.32） and （7.98±1.45） mm, and the transverse diameters were （4.04±0.83）, （4.09±1.07） mm; There was no obvious difference between left and right longitudinal diameters （t = 1.63, P = 0.11 ）, and left and right transverse diameters were close （t = 0.45, P= 0.65）. CONCLUSION ： The non-invasive techniques of volume rendering and multi-planar reconstruction after three-dimensional spiral CT thin-slice scan can clearly display the formand size of foramen ovale in healthy adults.