Using free bending method,the residual stress of the Ti(CN)coating on alloy Nb-752 was measured to be 2-3 GPa of which the thermal stress cmounts to 10—20%.An analysis on coating/substrate interface stress state show...Using free bending method,the residual stress of the Ti(CN)coating on alloy Nb-752 was measured to be 2-3 GPa of which the thermal stress cmounts to 10—20%.An analysis on coating/substrate interface stress state shows that the share stress at it is about O.1—0.2 GPa.The demage mode of the coating under external loading was proposed in terms of the amount and the direction of loading.展开更多
A TIA1N/MoS2-Ti coating was developed to improve the tribological characteristics of a single TiAlN coating. The MoS2-Ti layer was deposited by a DC magnetron sputtering system on the hard TiAIN coated SKD-11 steel su...A TIA1N/MoS2-Ti coating was developed to improve the tribological characteristics of a single TiAlN coating. The MoS2-Ti layer was deposited by a DC magnetron sputtering system on the hard TiAIN coated SKD-11 steel substrate. The titanium content in the MoS2-Ti layer was 11.3 at.% determined by EPMA. The surface morphology was observed by FE-SEM. The TiAlN layer exhibited excellent adhesion and hardness. However, the deposition of an MoS2-Zi layer on the TRAIN led to a significant improvement in tribological properties without affecting the adhesion to the substrate. The MoS2-Ti layer significantly decreased the friction coefficient of the TiAIN coating, and the drop was 48% after MoS2-Ti deposition. Also, the MoS2-Ti layer remarkably decreased the wear rate of the TtA1N coating.展开更多
Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analys...Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analysis,X-ray photoelectron spectroscopy,scanning electron microscope,and high-resolution transmission electron microscope,the influences of B content on the microstructure and properties of Ti B N coatings were investigated systematically.The results indicated that the microstructure and mechanical properties of Ti-B-N coatings largely depend on the transformation from FCC-TiN phase to HCP-TiB2 phase.With increasing B content and decreasing N content in the coatings,the coating microstructure evolves gradually from FCC-TiN/a-BN to HCP-TiB2 /a-BN via FCC-TiN+HCP-TiB2/a-BN.The highest microhardness of about 34 GPa is achieved,which corresponds to the nanocomposite Ti-63%B-N (mole fraction) coating consisting of the HCP-TiB2 nano-crystallites and amorphous BN phase.The lowest friction-coefficient was observed for the nanocomposite Ti-41%B-N (mole fraction) coating consisting of the FCC-TiN nanocrystallites and amorphous BN展开更多
Electric-spark deposition （ESD） was adopted for depositing a Ti（ CN） -based ceramic coating on the TC4 titanium alloy substrate using a laboratory-developed electric-spark deposition system, a nitrogen-sealed atmo...Electric-spark deposition （ESD） was adopted for depositing a Ti（ CN） -based ceramic coating on the TC4 titanium alloy substrate using a laboratory-developed electric-spark deposition system, a nitrogen-sealed atmosphere and graphite electrode. The surface morphology, microstructure, interfacial behavior between the coatings and substrate, phase and element composition of the coatings were investigated by scanning electron microscope （ SEM ） , X-ray diffraction （ XRD ） , X-ray photoelectron spectroscopy （ XPS ） and Auger electron spectroscopy （ AES ） . Microhardness profile was measured with a Vickers microhardness tester. The results show that metallurgical bond between the coating and substrate is realized and the phase of coatings are made up of Ti（ CN ） spherocrystal and dendritic crystal, TiV and C. Ti（ CN） ceramic particles, which is in-situ synthesized by the reaction among titanium from the substrate, carbon from the graphite electrode and nitrogen from the shielding nitrogen gas, is about 600 mn and distributes dispersively among the coatings. Microharduess profile falls off with the coatings thickness increasing and the highest microhardness values of the superficial coating could be up to 1 496HV, which is six times more than that of the substrate.展开更多
Ti-Si-N composite coatings were synthesized on a novel combining cathode and middle-frequency magnetron sputtering system, designed on an industrial scale. Ti was produced from the arc target and Si from magnetron tar...Ti-Si-N composite coatings were synthesized on a novel combining cathode and middle-frequency magnetron sputtering system, designed on an industrial scale. Ti was produced from the arc target and Si from magnetron target during deposition. The influences of negative bias voltage and Si content on the hardness and microstructure of the coatings were investigated. The composite coatings prepared under optimized conditions were characterized to be nc-TiN/a-Si3N4 structure with grain sizes of TiN ranging from 8-15 nm and exhibited a high hardness of 40 GPa. The enhancement of the hardness is suggested to be caused by the nanograin-amorphous structure effects.展开更多
Titanium-aluminium-nitride (Ti1-xAlxN) coatings were deposited by close-field un balanced magnetron sputtering on M42 steel substrates and WC-6wt%Co inserts at 4 50℃. The tribological behavior was analyzed by sliding...Titanium-aluminium-nitride (Ti1-xAlxN) coatings were deposited by close-field un balanced magnetron sputtering on M42 steel substrates and WC-6wt%Co inserts at 4 50℃. The tribological behavior was analyzed by sliding against steel and WC- 6wt%Co balls, while the turning performance was evaluated by a conventional tu rning machine at high cutting speeds without using coolants. In the tribological tests, the formation of transfer layer and the variations of hardness of the co atings played an important role for sliding against steel balls. For the coating s sliding against WC-6wt%Co balls, the Ti-Al-N coatings showed a similar frictio n coefficient, but the TiN coating exhibited a lower value. The difference could be explained by the tri-oxidation wear mechanism. In the turning tests, a super ior cutting performance of the coating was found at x=0.45, which endured 38 min utes before the tool flank wear reached the maximum value of 0.3mm, whereas only 20 minutes were endured for the TiN coating. The excellent performance of the c oatings in the turning tests could be explained by the enhanced mechanical prope rties and oxidation/diffusion resistance of the coatings.展开更多
文摘Using free bending method,the residual stress of the Ti(CN)coating on alloy Nb-752 was measured to be 2-3 GPa of which the thermal stress cmounts to 10—20%.An analysis on coating/substrate interface stress state shows that the share stress at it is about O.1—0.2 GPa.The demage mode of the coating under external loading was proposed in terms of the amount and the direction of loading.
文摘A TIA1N/MoS2-Ti coating was developed to improve the tribological characteristics of a single TiAlN coating. The MoS2-Ti layer was deposited by a DC magnetron sputtering system on the hard TiAIN coated SKD-11 steel substrate. The titanium content in the MoS2-Ti layer was 11.3 at.% determined by EPMA. The surface morphology was observed by FE-SEM. The TiAlN layer exhibited excellent adhesion and hardness. However, the deposition of an MoS2-Zi layer on the TRAIN led to a significant improvement in tribological properties without affecting the adhesion to the substrate. The MoS2-Ti layer significantly decreased the friction coefficient of the TiAIN coating, and the drop was 48% after MoS2-Ti deposition. Also, the MoS2-Ti layer remarkably decreased the wear rate of the TtA1N coating.
基金funded by a grant from the National Core Research Center(NCRC)Program through the National Research Foundation of Korea funded by the Ministry of Education,Science and Technology(No.2012-0000-957)by a grant from the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy,Republic of Korea
文摘Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analysis,X-ray photoelectron spectroscopy,scanning electron microscope,and high-resolution transmission electron microscope,the influences of B content on the microstructure and properties of Ti B N coatings were investigated systematically.The results indicated that the microstructure and mechanical properties of Ti-B-N coatings largely depend on the transformation from FCC-TiN phase to HCP-TiB2 phase.With increasing B content and decreasing N content in the coatings,the coating microstructure evolves gradually from FCC-TiN/a-BN to HCP-TiB2 /a-BN via FCC-TiN+HCP-TiB2/a-BN.The highest microhardness of about 34 GPa is achieved,which corresponds to the nanocomposite Ti-63%B-N (mole fraction) coating consisting of the HCP-TiB2 nano-crystallites and amorphous BN phase.The lowest friction-coefficient was observed for the nanocomposite Ti-41%B-N (mole fraction) coating consisting of the FCC-TiN nanocrystallites and amorphous BN
基金The work was supported by the Natural Science Foundation of Hebei Province of China under Grant No. E2007000566.
文摘Electric-spark deposition （ESD） was adopted for depositing a Ti（ CN） -based ceramic coating on the TC4 titanium alloy substrate using a laboratory-developed electric-spark deposition system, a nitrogen-sealed atmosphere and graphite electrode. The surface morphology, microstructure, interfacial behavior between the coatings and substrate, phase and element composition of the coatings were investigated by scanning electron microscope （ SEM ） , X-ray diffraction （ XRD ） , X-ray photoelectron spectroscopy （ XPS ） and Auger electron spectroscopy （ AES ） . Microhardness profile was measured with a Vickers microhardness tester. The results show that metallurgical bond between the coating and substrate is realized and the phase of coatings are made up of Ti（ CN ） spherocrystal and dendritic crystal, TiV and C. Ti（ CN） ceramic particles, which is in-situ synthesized by the reaction among titanium from the substrate, carbon from the graphite electrode and nitrogen from the shielding nitrogen gas, is about 600 mn and distributes dispersively among the coatings. Microharduess profile falls off with the coatings thickness increasing and the highest microhardness values of the superficial coating could be up to 1 496HV, which is six times more than that of the substrate.
基金Funded by the Natural Science Foundation of China(No.10435060 andNo. 10675095)
文摘Ti-Si-N composite coatings were synthesized on a novel combining cathode and middle-frequency magnetron sputtering system, designed on an industrial scale. Ti was produced from the arc target and Si from magnetron target during deposition. The influences of negative bias voltage and Si content on the hardness and microstructure of the coatings were investigated. The composite coatings prepared under optimized conditions were characterized to be nc-TiN/a-Si3N4 structure with grain sizes of TiN ranging from 8-15 nm and exhibited a high hardness of 40 GPa. The enhancement of the hardness is suggested to be caused by the nanograin-amorphous structure effects.
文摘Titanium-aluminium-nitride (Ti1-xAlxN) coatings were deposited by close-field un balanced magnetron sputtering on M42 steel substrates and WC-6wt%Co inserts at 4 50℃. The tribological behavior was analyzed by sliding against steel and WC- 6wt%Co balls, while the turning performance was evaluated by a conventional tu rning machine at high cutting speeds without using coolants. In the tribological tests, the formation of transfer layer and the variations of hardness of the co atings played an important role for sliding against steel balls. For the coating s sliding against WC-6wt%Co balls, the Ti-Al-N coatings showed a similar frictio n coefficient, but the TiN coating exhibited a lower value. The difference could be explained by the tri-oxidation wear mechanism. In the turning tests, a super ior cutting performance of the coating was found at x=0.45, which endured 38 min utes before the tool flank wear reached the maximum value of 0.3mm, whereas only 20 minutes were endured for the TiN coating. The excellent performance of the c oatings in the turning tests could be explained by the enhanced mechanical prope rties and oxidation/diffusion resistance of the coatings.
