The 2024 Al composites containing W, Ta were fabricated by powder metallurgy for their potential use as shielding material. W, Ta powders and gas-atomized 2024 Al aluminum powders were mixed by a ball mixer. The mixtu...The 2024 Al composites containing W, Ta were fabricated by powder metallurgy for their potential use as shielding material. W, Ta powders and gas-atomized 2024 Al aluminum powders were mixed by a ball mixer. The mixtures were consolidated by cold isostatic pressing (CIP) and then hot-extruded into full-density bars. The extruded bars were heat treated in T6 conditions. The microstructure and its relationship with the mechanical properties were investigated by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that the particles of nonuniform size and irregular shape randomly disperse in the 2024 aluminum alloy matrix. The tensile tests show that an increase of tensile strength and decrease of elongation to failure of the heat treated composites compared with the extruded composites.展开更多
A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, w...A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, was obtained when a 15 μm thick interlayer was used. The results of the shear testing and SEM indicate that fracture of the joint presented characteristics of ductile rupture.展开更多
The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are...The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are milling time,rotational speed,mass fraction of CNTs and ball to powder ratio on UST and hardness of CNTs / Al2024 composites are investigated. Based on the central composite design( CCD),a quadratic model is developed to correlate the fabrication variables to the UST and hardness. From the analysis of variance( ANOVA),the most influential factor on each experimental design response is identified. The optimum conditions for preparing CNTs / Al2024 composites are found as follows: 1. 53 h milling time,900 r / min rotational speed,mass fraction of CNTs 2. 87% and Ball to powder ratio 25 ∶ 1. The predicted maximum UST and hardness are 273.30 MPa and 261.36 HV,respectively. And the experimental values are 283.25 MPa and256.8 HV,respectively. It is indicated that the predicted UST and hardness after process optimization are found to agree satisfactory with the experimental values.展开更多
In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HE...In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.展开更多
Al-Al3Ti composites were prepared by a direct reaction method, in which Al3Ti was formed by the reaction of Ti and Al in aluminum alloy melt. The morphology of Al3Ti changes apparently from the fine particle, needle-l...Al-Al3Ti composites were prepared by a direct reaction method, in which Al3Ti was formed by the reaction of Ti and Al in aluminum alloy melt. The morphology of Al3Ti changes apparently from the fine particle, needle-like to large block with the increase of Al3Ti content. The addition of magnesium can markedly change the morphology of Al3Ti and reduce their size. Short rod-like Al3Ti was formed and homogeneous distribution was obtained with the addition of 3 wt.% Mg. The effect of Al3Ti and Mg on the microstructure of Al-Al3Ti composites and the mechanism were also discussed.展开更多
The corrosion resistance of 2024 Al and SiC particle reinforced 2024 Al metal matrix composite (SiCp?024AI MMC) in 3.5% NaCl solution was investigated with electrochemical method and immersion test, and the corrosion ...The corrosion resistance of 2024 Al and SiC particle reinforced 2024 Al metal matrix composite (SiCp?024AI MMC) in 3.5% NaCl solution was investigated with electrochemical method and immersion test, and the corrosion protection of sulfuric acid anodized coatings on both materials was evaluated by electrochemical impedance spectroscopy. The results showed that the SiCp?024AI MMC is more susceptible to corrosion than its matrix alloy in 3.5% NaCI. For 2024AI, the anodized coating provides excellent corrosion resistance to 3.5% NaCI. The anodized coating on the SiCp?024AI provides satisfactory corrosion protection, but it is not as effective as that for 2024AI because the structure of the anodized layer is affected by the SiC particulates.展开更多
A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of e...A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.展开更多
In situ Al2O3 whiskers reinforced Ti-Al intermetallic composites were fabricated at ~1200℃ by reaction sintering of cold-consolidated fillets consisting mainly of Ti, Al, and different additives. The phases and micro...In situ Al2O3 whiskers reinforced Ti-Al intermetallic composites were fabricated at ~1200℃ by reaction sintering of cold-consolidated fillets consisting mainly of Ti, Al, and different additives. The phases and microstructures of the sintered composites were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS). The process of synthesis was investigated using differential thermal analysis (DTA). The effects of processing parameters and additives on the microstructures of the composites and the development of whisker were examined. It is found that the morphology of the whisker is strongly influenced by the additives, the exothermal reaction process, and the processing parameters.展开更多
It is showed that there are Ti 3Al, Ti 2Cu and β phase in the interface of Ti/Ti Al composites reinforced with Y 2O 3 Cr composite soft coated Ti fiber, and that interface bonding is intact. Bending strength ...It is showed that there are Ti 3Al, Ti 2Cu and β phase in the interface of Ti/Ti Al composites reinforced with Y 2O 3 Cr composite soft coated Ti fiber, and that interface bonding is intact. Bending strength of the composites can be increased by 26%, to 709 MPa, and bending deflection increased slightly compared with the Ti/Ti Al composites reinforced by Ti fibers coated with Y 2O 3.展开更多
Si_(3)N_(4p)/2024Al composite was fabricated by squeeze casting method and treated by extrusion deformation.Microstructure analyses indicate that Si_(3)N_(4) particles in the composite are in cylindrical polyhedron sh...Si_(3)N_(4p)/2024Al composite was fabricated by squeeze casting method and treated by extrusion deformation.Microstructure analyses indicate that Si_(3)N_(4) particles in the composite are in cylindrical polyhedron shape.Extrusion deformation is beneficial to uniform distribution of Si_(3)N_(4) particles and improves the relative density of Si_(3)N_(4p)/2024Al composite.Tensile strength of Si_(3)N_(4p)/2024Al composite increases by 76.6%after T6 treatment,and after extrusion and T6 treatment it is by 57.6%more than T6 treatment only.Elastic modulus of Si_(3)N_(4p)/2024Al composite increases a little after T6 treatment but increases by 33.5%after extrusion deformation.展开更多
Al matrix composites with a high volume fraction of reinforcements were fabricated with a compact of Al-Ti-B4C powder mixtures by quick spontaneous infiltration(QSI) process in an aluminum melt. Given the exothermal n...Al matrix composites with a high volume fraction of reinforcements were fabricated with a compact of Al-Ti-B4C powder mixtures by quick spontaneous infiltration(QSI) process in an aluminum melt. Given the exothermal nature of the reaction between CuO and Al, a certain amount of CuO addition to the Al-Ti-B4C system dramatically increases the adiabatic temperature and thereby enables the complete combustion reaction in an aluminum melt(about 1,173 K). After the QSI process, the compact fabricated with CuO retains its original shape and the obtained composite exhibits sound microstructure containing reaction products of TiB2, Al3BC and B4C. The formation of such reinforcements when adding CuO contributes to enhancing the properties of the composites that show far superior hardness and elastic modulus of 3.03 GPa and 158.9 GPa, respectively, with lower coefficient of thermal expansion(9.44 ppm?K-1) compared to those with no CuO addition.展开更多
TiAl/Ti2AlC composites were prepared by in-situ hot pressing of TilAl/C powders mixtures and sintered at different temperatures were investigated by X- ray diffraction （ XRD ） of samples. The reaction procedure of T...TiAl/Ti2AlC composites were prepared by in-situ hot pressing of TilAl/C powders mixtures and sintered at different temperatures were investigated by X- ray diffraction （ XRD ） of samples. The reaction procedure of Ti-Al-C system could be divided into three stnges. Below 900℃ , Ti reacts with Al to form TiAl intermetallics ; above 900 ℃ , C reacts with remain Ti to form TiC triggered by the exothermal reaction of Ti and Al ; TiAl reacts with TiC to produce dense TiAl/Ti2AlC compasites.In the holding stage, ternary Ti2AlC develops to layered polycrystal and composites pyknosis in the meanwhile. The mechanism of synthesis and microstructure was especially discussed.展开更多
文摘The 2024 Al composites containing W, Ta were fabricated by powder metallurgy for their potential use as shielding material. W, Ta powders and gas-atomized 2024 Al aluminum powders were mixed by a ball mixer. The mixtures were consolidated by cold isostatic pressing (CIP) and then hot-extruded into full-density bars. The extruded bars were heat treated in T6 conditions. The microstructure and its relationship with the mechanical properties were investigated by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that the particles of nonuniform size and irregular shape randomly disperse in the 2024 aluminum alloy matrix. The tensile tests show that an increase of tensile strength and decrease of elongation to failure of the heat treated composites compared with the extruded composites.
基金the National Advanced Technology "863" Project of China with !No.715-005-0800
文摘A study has been made on diffusion bonding of SiCp/2024Ai composites by means of pure Al interlayer. In the condition of TB=843 K, PB=16 MPa, tB= 60 min, the diffusion bonded joint, with a shear strength of 235 MPa, was obtained when a 15 μm thick interlayer was used. The results of the shear testing and SEM indicate that fracture of the joint presented characteristics of ductile rupture.
基金Sponsored by the Program for Innovative Research Team in University of Yunnan Province and Major Projects of Yunnan Province(Grant No.2014FC001)
文摘The mathematical models are developed to evaluate the ultimate tensile strength( UTS) and hardness of CNTs / Al2024 composites fabricated by high-energy ball milling. The effects of the preparation variables which are milling time,rotational speed,mass fraction of CNTs and ball to powder ratio on UST and hardness of CNTs / Al2024 composites are investigated. Based on the central composite design( CCD),a quadratic model is developed to correlate the fabrication variables to the UST and hardness. From the analysis of variance( ANOVA),the most influential factor on each experimental design response is identified. The optimum conditions for preparing CNTs / Al2024 composites are found as follows: 1. 53 h milling time,900 r / min rotational speed,mass fraction of CNTs 2. 87% and Ball to powder ratio 25 ∶ 1. The predicted maximum UST and hardness are 273.30 MPa and 261.36 HV,respectively. And the experimental values are 283.25 MPa and256.8 HV,respectively. It is indicated that the predicted UST and hardness after process optimization are found to agree satisfactory with the experimental values.
基金financial supports from the National Natural Science Foundation of China (No. 51875062)China Postdoctoral Science Foundation (No. 2021M700567)。
文摘In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.
文摘Al-Al3Ti composites were prepared by a direct reaction method, in which Al3Ti was formed by the reaction of Ti and Al in aluminum alloy melt. The morphology of Al3Ti changes apparently from the fine particle, needle-like to large block with the increase of Al3Ti content. The addition of magnesium can markedly change the morphology of Al3Ti and reduce their size. Short rod-like Al3Ti was formed and homogeneous distribution was obtained with the addition of 3 wt.% Mg. The effect of Al3Ti and Mg on the microstructure of Al-Al3Ti composites and the mechanism were also discussed.
基金The financial supports from the Research Fund for the Doc-toral Program of Higher Education (grant No.97014517), State Key Laboratory for Metal Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences and the National Natural Sc
文摘The corrosion resistance of 2024 Al and SiC particle reinforced 2024 Al metal matrix composite (SiCp?024AI MMC) in 3.5% NaCl solution was investigated with electrochemical method and immersion test, and the corrosion protection of sulfuric acid anodized coatings on both materials was evaluated by electrochemical impedance spectroscopy. The results showed that the SiCp?024AI MMC is more susceptible to corrosion than its matrix alloy in 3.5% NaCI. For 2024AI, the anodized coating provides excellent corrosion resistance to 3.5% NaCI. The anodized coating on the SiCp?024AI provides satisfactory corrosion protection, but it is not as effective as that for 2024AI because the structure of the anodized layer is affected by the SiC particulates.
文摘A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.
基金This work was supported by the National Natural Science Foundation of China (No. 50432010, 50372037).
文摘In situ Al2O3 whiskers reinforced Ti-Al intermetallic composites were fabricated at ~1200℃ by reaction sintering of cold-consolidated fillets consisting mainly of Ti, Al, and different additives. The phases and microstructures of the sintered composites were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS). The process of synthesis was investigated using differential thermal analysis (DTA). The effects of processing parameters and additives on the microstructures of the composites and the development of whisker were examined. It is found that the morphology of the whisker is strongly influenced by the additives, the exothermal reaction process, and the processing parameters.
文摘It is showed that there are Ti 3Al, Ti 2Cu and β phase in the interface of Ti/Ti Al composites reinforced with Y 2O 3 Cr composite soft coated Ti fiber, and that interface bonding is intact. Bending strength of the composites can be increased by 26%, to 709 MPa, and bending deflection increased slightly compared with the Ti/Ti Al composites reinforced by Ti fibers coated with Y 2O 3.
基金Project(HITQNJS.2008.057)Supported by Development Program for Outstanding Young Teachers in Harbin Institute of Technology,China。
文摘Si_(3)N_(4p)/2024Al composite was fabricated by squeeze casting method and treated by extrusion deformation.Microstructure analyses indicate that Si_(3)N_(4) particles in the composite are in cylindrical polyhedron shape.Extrusion deformation is beneficial to uniform distribution of Si_(3)N_(4) particles and improves the relative density of Si_(3)N_(4p)/2024Al composite.Tensile strength of Si_(3)N_(4p)/2024Al composite increases by 76.6%after T6 treatment,and after extrusion and T6 treatment it is by 57.6%more than T6 treatment only.Elastic modulus of Si_(3)N_(4p)/2024Al composite increases a little after T6 treatment but increases by 33.5%after extrusion deformation.
基金supported by a grant from the Fundamental R&D Program for Core Technology of Materialsfunded by the Ministry of Knowledge Economy,Republic of Korea(No.10037308)
文摘Al matrix composites with a high volume fraction of reinforcements were fabricated with a compact of Al-Ti-B4C powder mixtures by quick spontaneous infiltration(QSI) process in an aluminum melt. Given the exothermal nature of the reaction between CuO and Al, a certain amount of CuO addition to the Al-Ti-B4C system dramatically increases the adiabatic temperature and thereby enables the complete combustion reaction in an aluminum melt(about 1,173 K). After the QSI process, the compact fabricated with CuO retains its original shape and the obtained composite exhibits sound microstructure containing reaction products of TiB2, Al3BC and B4C. The formation of such reinforcements when adding CuO contributes to enhancing the properties of the composites that show far superior hardness and elastic modulus of 3.03 GPa and 158.9 GPa, respectively, with lower coefficient of thermal expansion(9.44 ppm?K-1) compared to those with no CuO addition.
文摘TiAl/Ti2AlC composites were prepared by in-situ hot pressing of TilAl/C powders mixtures and sintered at different temperatures were investigated by X- ray diffraction （ XRD ） of samples. The reaction procedure of Ti-Al-C system could be divided into three stnges. Below 900℃ , Ti reacts with Al to form TiAl intermetallics ; above 900 ℃ , C reacts with remain Ti to form TiC triggered by the exothermal reaction of Ti and Al ; TiAl reacts with TiC to produce dense TiAl/Ti2AlC compasites.In the holding stage, ternary Ti2AlC develops to layered polycrystal and composites pyknosis in the meanwhile. The mechanism of synthesis and microstructure was especially discussed.
