In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the ...In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the apparent viscosity and microstructure were investigated. The results showed that adding Ti B2 is effective for optimizing primary α-Al, but compared with the 4.5wt.%Ti B2/7075 composite, the addition of 9wt.%Ti B2 had no further significant refinement role in the 9wt.%Ti B2/7075 composite due to particle aggregation. The viscosities of semi-solid 7075 alloy and Ti B2/7075 composite slurries increased with an increase in solid fraction, but decreased with an increase in shear rate. The viscosity of 4.5wt.% Ti B2/7075 was the lowest among the three samples, and that of 7075 alloy was the highest under the same conditions. The primary α-Al grain size was decreased, and the dendritic grains grew into spherical shapes after shearing. Based on the experimental results, viscosity models of the semi-solid 7075 alloy and 4.5wt.% and 9wt.%Ti B2/7075 composites were formulated. According to the simulation results, the shrinkage porosity of the 4.5wt.%Ti B2/7075 wheel was lower than those of the 7075 alloy and 9wt.%Ti B2/7075 wheels.展开更多
The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of sing...The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of single B2 phase, A.C. microstructure consisted of B2 phase matrix and second phase in some regions of the B2 phase crystal grains, and C.C. and F.C. microstructure appeared as a Widmannstatten structure consisting of coarse α 2 phase plates and β phase stripes between the plates. With the decreasing of colling rate, the tension strength was obviously decreased and the plasticity was slightly increased at room temperature.展开更多
Transition metal diborides based ultrahigh temperature ceramics(UHTCs) are characterized by high melting point, high strength and hardness, and high electrical and thermal conductivity. The high thermal conductivity a...Transition metal diborides based ultrahigh temperature ceramics(UHTCs) are characterized by high melting point, high strength and hardness, and high electrical and thermal conductivity. The high thermal conductivity arises from both electronic and phonon contributions. Thus electronic and phonon contributions must be controlled simultaneously in reducing the thermal conductivity of transition metal diborides. In high entropy(HE) materials, both electrons and phonons are scattered such that the thermal conductivity can significantly be reduced, which opens a new window to design novel insulating materials. Inspired by the high entropy effect, porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 is designed in this work as a new thermal insulting ultrahigh temperature material and is synthesized by an in-situ thermal borocarbon reduction/partial sintering process. The porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 possesses high porosity of 75.67%, pore size of 0.3–1.2 μm, homogeneous microstructure with small grain size of 400–800 nm, which results in low room temperature thermal diffusivity and thermal conductivity of 0.74 mm2 s^-1 and 0.51 W m^-1K^-1, respectively. In addition, it exhibits high compressive strength of3.93 MPa. The combination of these properties indicates that exploring porous high entropy ceramics such as porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 is a novel strategy in making UHTCs thermal insulating.展开更多
To improve the wear resistance of aluminum alloy frictional parts, Ti B2particles reinforced Ni-base alloy composite coatings were prepared on aluminum alloy 7005 by laser cladding. The microstructure and tribological...To improve the wear resistance of aluminum alloy frictional parts, Ti B2particles reinforced Ni-base alloy composite coatings were prepared on aluminum alloy 7005 by laser cladding. The microstructure and tribological properties of the composite coatings were investigated. The results show that the composite coating contains the phases of Ni Al, Ni3Al, Al3Ni2, TiB2, TiB, TiC, CrB, and Cr23C6.Its microhardness is HV0.5855.8, which is 15.4 % higher than that of the Ni-base alloy coating and is 6.7 times as high as that of the aluminum alloy. The friction coefficients of the composite coatings are reduced by 6.8 %–21.6 % and 13.2 %–32.4 % compared with those of the Ni-base alloy coatings and the aluminum alloys, while the wear losses are 27.4 %–43.2 % less than those of the Ni-base alloy coatings and are only 16.5 %–32.7 % of those of the aluminum alloys at different loads. At the light loads ranging from 3 to 6 N, the calculated maximum contact stress is smaller than the elastic limit contact stress. The wear mechanism of the composite coatings is micro-cutting wear, but changes into multi-plastic deformation wear at 9 N due to the higher calculated maximum contact stress than the elastic limit contact stress. As the loads increase to 12 N, the calculated flash temperature rises to 332.1 °C.The composite coating experiences multi-plastic deformation wear, micro-brittle fracture wear, and oxidative wear.展开更多
文摘In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the apparent viscosity and microstructure were investigated. The results showed that adding Ti B2 is effective for optimizing primary α-Al, but compared with the 4.5wt.%Ti B2/7075 composite, the addition of 9wt.%Ti B2 had no further significant refinement role in the 9wt.%Ti B2/7075 composite due to particle aggregation. The viscosities of semi-solid 7075 alloy and Ti B2/7075 composite slurries increased with an increase in solid fraction, but decreased with an increase in shear rate. The viscosity of 4.5wt.% Ti B2/7075 was the lowest among the three samples, and that of 7075 alloy was the highest under the same conditions. The primary α-Al grain size was decreased, and the dendritic grains grew into spherical shapes after shearing. Based on the experimental results, viscosity models of the semi-solid 7075 alloy and 4.5wt.% and 9wt.%Ti B2/7075 composites were formulated. According to the simulation results, the shrinkage porosity of the 4.5wt.%Ti B2/7075 wheel was lower than those of the 7075 alloy and 9wt.%Ti B2/7075 wheels.
文摘The microstructure of alloy Ti 3Al 10Nb 3V 1Mo after heated at 1170℃ for 1 h and cooled to room temperature at different rates was investigated by TEM. The result showed that W.Q. microstructure consisted of single B2 phase, A.C. microstructure consisted of B2 phase matrix and second phase in some regions of the B2 phase crystal grains, and C.C. and F.C. microstructure appeared as a Widmannstatten structure consisting of coarse α 2 phase plates and β phase stripes between the plates. With the decreasing of colling rate, the tension strength was obviously decreased and the plasticity was slightly increased at room temperature.
基金supported by the National Natural Science Foundation of China (Nos. 51672064 and U1435206)
文摘Transition metal diborides based ultrahigh temperature ceramics(UHTCs) are characterized by high melting point, high strength and hardness, and high electrical and thermal conductivity. The high thermal conductivity arises from both electronic and phonon contributions. Thus electronic and phonon contributions must be controlled simultaneously in reducing the thermal conductivity of transition metal diborides. In high entropy(HE) materials, both electrons and phonons are scattered such that the thermal conductivity can significantly be reduced, which opens a new window to design novel insulating materials. Inspired by the high entropy effect, porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 is designed in this work as a new thermal insulting ultrahigh temperature material and is synthesized by an in-situ thermal borocarbon reduction/partial sintering process. The porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 possesses high porosity of 75.67%, pore size of 0.3–1.2 μm, homogeneous microstructure with small grain size of 400–800 nm, which results in low room temperature thermal diffusivity and thermal conductivity of 0.74 mm2 s^-1 and 0.51 W m^-1K^-1, respectively. In addition, it exhibits high compressive strength of3.93 MPa. The combination of these properties indicates that exploring porous high entropy ceramics such as porous HE(Zr0.2Hf0.2Ti0.2Nb0.2Ta0.2)B2 is a novel strategy in making UHTCs thermal insulating.
基金financially supported by the Research Program of General Armament Department of China (No. 2012500)
文摘To improve the wear resistance of aluminum alloy frictional parts, Ti B2particles reinforced Ni-base alloy composite coatings were prepared on aluminum alloy 7005 by laser cladding. The microstructure and tribological properties of the composite coatings were investigated. The results show that the composite coating contains the phases of Ni Al, Ni3Al, Al3Ni2, TiB2, TiB, TiC, CrB, and Cr23C6.Its microhardness is HV0.5855.8, which is 15.4 % higher than that of the Ni-base alloy coating and is 6.7 times as high as that of the aluminum alloy. The friction coefficients of the composite coatings are reduced by 6.8 %–21.6 % and 13.2 %–32.4 % compared with those of the Ni-base alloy coatings and the aluminum alloys, while the wear losses are 27.4 %–43.2 % less than those of the Ni-base alloy coatings and are only 16.5 %–32.7 % of those of the aluminum alloys at different loads. At the light loads ranging from 3 to 6 N, the calculated maximum contact stress is smaller than the elastic limit contact stress. The wear mechanism of the composite coatings is micro-cutting wear, but changes into multi-plastic deformation wear at 9 N due to the higher calculated maximum contact stress than the elastic limit contact stress. As the loads increase to 12 N, the calculated flash temperature rises to 332.1 °C.The composite coating experiences multi-plastic deformation wear, micro-brittle fracture wear, and oxidative wear.
