Effect of Ti substitution on hydrogen storage properties of Zr_(1-x)Ti_xCo (x = 0, 0.1, 0.2, 0.3) alloys

Zr1-xTixCo(x = 0, 0.1, 0.2, 0.3) alloys were prepared by arc-melting method and the effect of Ti substitution on hydrogen storage properties was studied systematically. Hydrogen desorption pressure-composition-temperature(PCT) measurements were carried out using Sievert’s type volumetric apparatus for ZrCo(at 473 K, 573 K and 673 K) and Zr1-xTixCo alloys(at 673 K), respectively. Products after dehydrogenation were characterized by X-ray diffraction(XRD). In addition, the kinetics of Zr1-xTixCo hydride was investigated at 473 K and 673 K,respectively, under hydrogen pressure of 5 MPa. Results showed that Ti substitution for Zr did not change the crystal structure of ZrCo phase.With the increase of temperature from 473 K to 673 K, the extent of disproportionation for ZrCo alloy increased. With Ti content increasing at 673 K, the desorption equilibrium pressure of Zr1-xTixCo-H2 systems elevated and the disproportionation reaction of Zr1-xTixCo alloys was inhibited effectively. Ti substitution decreased the kinetics rate and the effective hydrogen storage capacity of Zr1-xTixCo alloys slightly.Generally speaking, it was found that Zr0.8Ti0.2Co alloy had better anti-disproportionation property with less decrease of effective hydrogen storage capacity which was beneficial to tritium application in the International Thermonuclear Experimental Reactor(ITER).

Influences of Ti substitution on the structure and electrochemical properties of Mg_(1-x)Ti_xNi(x=0,0.1, 0.2, and 0.3) hydrogen storage alloys

MgNi-based hydrogen storage alloys Mg1–xTixNi （x = 0, 0.1, 0.2, and 0.3） were prepared by means of mechanical alloying. Mg in the alloy was partially substituted by Ti to improve the cycle stability of the alloys. The effects of the substitution of Ti for Mg on the microstructure and electrochemical performances of the alloys were investigated in detail. The results indicate that the substitution of Ti for Mg obviously decreases the discharge capacity, but it significantly improves their cycle stabilities. The microstructure of the alloys analyzed by X-ray diffraction （XRD） and scanning electron microscopy （SEM） shows that the alloys have a dominatingly amorphous structure. The substitution of Ti for Mg helps to improve the anti-oxidation/corrosion ability of the MgNi alloy but demolishes the electrochemical kinetics of hydrogenation/dehydrogenation. The Mg0.9Ti0.1Ni alloy electrode milled for 80 h exhibits the best integrative capability, which has the maximal discharge capacity of 331.66 mAh/g and the C30/Cmax of 63.65%.

ON SIMULTANEOUS SUBSTITUTION OF TI AND V INTO MCM-41 TYPE MOLECULAR SIEVE

The new crystalline V-Ti-silicalite with mesoporous MCM-41 type molecular sieve structure is synthesized hydrothermally; The framework IR spectra associated with ESR, Si-29 MAS NMR, DRS and XPS data shows that V and Ti are simultaneously incorporated into V-TiMCM-41 framework.

Tailoring of Bandgap and Spin-Orbit Splitting in ZrSe_(2) with Low Substitution of Ti for Zr

Tuning the bandgap in layered transition metal dichalcogenides(TMDCs) is crucial for their versatile applications in many fields. The ternary formation is a viable method to tune the bandgap as well as other intrinsic properties of TMDCs, because the multi-elemental characteristics provide additional tunability at the atomic level and advantageously alter the physical properties of TMDCs. Herein, ternary Ti_(x)Zr_(1-x)Se_(2) single crystals were synthesized using the chemical-vapor-transport method. The changes in electronic structures of ZrSe_(2) induced by Ti substitution were revealed using angle-resolved photoemission spectroscopy. Our data show that at a low level of Ti substitution, the bandgap of Ti_(x)Zr_(1-x)Se_(2) decreases monotonically, and the electronic system undergoes a transition from a semiconducting to a metallic state without a significant variation of dispersions of valence bands. Meanwhile, the size of spin-orbit splitting dominated by Se 4p orbitals decreases with the increase of Ti doping. Our work shows a convenient way to alter the bandgap and spin-orbit coupling in TMDCs at the low level of substitution of transition metals.

Fibonacci Stoichiometry and Superb Performance of Nb16W5O55 and Related Super-Battery Materials

In this contribution, two important crystallographic concepts for the formation of a series of block structures associated with channeling have been compared: chemical twinning and crystallographic shear. Twin planes respectively shear planes besides formed channels serve as a sink for charge carriers or, when the oxidation state of metal ions can be reduced, as a reservoir for intercalated lithium. In this way, Wadsley-Roth shear phases such as niobium tungsten oxide exhibit channels for ultra-fast lithium-ion diffusion. They are in focus as anode material for super-batteries, superb in terms of energy respectively power density, charging time, cycle life and safety. It should be noted that the transition metal to oxygen ratio TM/O = 21/55 of the title compound is a Fibonacci number quotient. Also, the crystal lattice can be traced back to Fibonacci geometry. When replacing only 0.0213 tungsten atoms in the formula with less expensive titanium, a TM/O ratio of 0.381966 =ϕ2 can be adapted besides an average valence electron concentration of 2⋅ϕ-2, where represents the most irrational number of the golden mean. The additional disorder caused by even such small titanium replacement and accompanied oxygen vacancies could fasten up the already high lithium diffusion further. Ultrasonic treatment may be applied besides thermal cycling to prepare phase-pure of the highest electrochemical performance. A replacement of oxygen by some fluorine atoms is an obvious synthesis possibility, but the higher binding energy expected between lithium and fluorine in contrast to oxygen may rather hinder than promote lithium diffusion.

Structure and electrochemical characteristics of Mg–Ti–Ni-based electrode alloys synthesized by mechanical milling

The vacuum induction melting was adopted to fabricating Mg_(50−x)Ti_(x)Ni_(45)Al_(3)Co_(2)(x=0,1,2,3,4 at.%)composites protected by the high-purity helium atmosphere.Subsequently,the surface modification treatment of the as-cast alloys was carried out by mechanically coating nickel.The amorphous and nanocrystalline Mg_(50−x)Ti_(x)Ni_(45)Al_(3)Co_(2)(x=0–4)+50 wt.%Ni hydrogen storing alloys as the negative materials in batteries were prepared through ball milling,and the influences of milling time and Ti dosage on the structure and electrochemical hydrogen storing behaviors of the corresponding samples were studied in detail.The electrochemical testing reveals that the as-milled alloys have excellent performances and can finish the electrochemical hydrogenation and dehydrogenation at indoor temperature.In the first cycle without activation,the ball milling alloy obtains the maximum value of discharge capacity.Discharge capacity and cyclic steadiness of the composites conspicuously grow as Ti content and milling duration increase.Concretely,the capacity retaining rate at 100th cycle and the discharge capacity of 30 h milling samples augment from 53%to 78%and from 435.2 to 567.2 mAh/g with changing Ti content from 0 to 4.The same performances of the alloy(x=4)are enhanced from 61%to 78%and from 379.9 to 567.2 mAh/g,respectively,with extending milling duration.Moreover,high rate discharge ability,potential-step measurements,potentiodynamic polarization curves and electrochemical impedance spectrum manifest that the electrochemical kinetics properties can achieve significant amelioration as Ti content varies and milling duration is extended.

Effects of Ti and Zr Substituted on the Electrochemical Characteristics of MgNi-Based Alloy Electrodes

Mg-based hydrogen storage alloys MgNi, Mg0.9Ti0.1Ni, and Mg0.9Ti0.06Zr0.04Ni were successfully prepared by means of mechanical alloying （MA）. The structure and the electrochemical characteristics of these Mg-based materials were studied. The X-ray diffraction （XRD） result shows that the main phases of the alloys exhibit amorphous structure. The scanning electron microscopy （SEM） photograph shows that the particle size of Ti and Zr substituted alloys was about 2-4 μm in diameter. The cycle lives of the alloys were prolonged by adding Ti and Zr. After 50 charge-discharge cycles, the discharge capacity of Mg0.9Ti0.06Zr0.04Ni was 91.74% higher than that of MgNi alloy and 37.96% higher than that of Mg0.9Ti0.1Ni alloy. The main reason for the electrode capacity decay is the formation of Mg（OH）2 （product of Mg corrosion） at the surface of alloy. The potentiodynamic polarization result indicates that Ti and Zr doping improves the anticorrosion in an alkaline solution. The electrochemical impedance spectroscopy （EIS） results suggest that proper amount of Ti and Zr doping improves the electrochemical catalytic activity significantly.