Bulk metallic glass Zr_52.5Ni_14.6Al_10Cu_17.9Ti_5 was prepared by melt injection casting method. Its glass transition and crystallization temperatures were determined by differential scanning calorimetry (DSC) to be ...Bulk metallic glass Zr_52.5Ni_14.6Al_10Cu_17.9Ti_5 was prepared by melt injection casting method. Its glass transition and crystallization temperatures were determined by differential scanning calorimetry (DSC) to be 631 K and 710 K respectively. By analysis of X-ray diffractometry (XRD) and transmission electron microscopy (TEM ), the predominant crystallized phase of Zr_2Ni0.67O0.33 distributed on glass state matrix was detected after annealing at 673 K for 600 s. The transformation to Zr_2Ni_0.67O_0.33 and a small amount of ZrAl and Zr_2Cu took place after annealing for 600 s at temperature from 703 K to 723 K. With increasing annealing temperature from 753 K to 823 K, the amounts of ZrAl and Zr_2Cu increased, but the size of the crystals did not significantly change. The transformation to Zr_2Ni_0.67O_0.33 is interface-controlled, but is diffusion-controlled to Zr_2Cu and ZrAl. With increasing annealing temperature up to 200 K above T_x, the nanometer grains became very fine because of the increase of nucleation rate for Zr_2Cu and ZrAl.展开更多
In this paper, the vacuum brazing of Si3N4 ceramic was carried out with Ti40Zr25Ni15Cu20 amorphous filler metal. The interfacial microstructure was investigated by scanning electron microscopy （ SEM ）, energy disper...In this paper, the vacuum brazing of Si3N4 ceramic was carried out with Ti40Zr25Ni15Cu20 amorphous filler metal. The interfacial microstructure was investigated by scanning electron microscopy （ SEM ）, energy dispersive spectroscopy （EDS） etc. According to the analysis, the interface reaction layer was mode up of TiN abut on the ceramic and the Ti-Si, Zr-Si compounds. The influence of brazing temperature and holding time on the joint strength was also studied. The results shows that the joint strength first increased and then decreased with the increasing of holding time and brazing temperature. The joint strength was significantly affected by the thickness of the reaction layer. Under the same experimental conditions, the joint brazed with amorphous filler metal exhibits much higher strength compared with the one brazed with crystalline filler metal with the same composition. To achieve higher joint strength at relatively low temperature, it is favorable to use the amorphous filler metal than the crystalline filler metal.展开更多
The crystallization kinetics of Zr 41 Ti 14 Cu 12.5 Ni 10 Be 22.5 bulk metallic glass has been studied by using DSC and XRD. The results show that two exothermal peaks are observed when the alloy is heated to 500?℃, ...The crystallization kinetics of Zr 41 Ti 14 Cu 12.5 Ni 10 Be 22.5 bulk metallic glass has been studied by using DSC and XRD. The results show that two exothermal peaks are observed when the alloy is heated to 500?℃, one peak results dominantly from the formation of Ti 2Ni ( α phase transition), the other peak is mainly due to the formation of Zr 2Cu ( β phase transition). At the beginning of the crystallization, the activation energy of the α phase is smaller, and it increases with increasing crystallized fraction ( x c). When x c increases to 90%, the crystallization activation energy shows the largest value (220?kJ/mol). The crystallization activation energy of the β phase remains about 227?kJ/mol, as it’s crystallized fraction is below 60%, and then it increases with increasing crystallized fraction, and shows the largest activation energy of 257?kJ/mol, as the x c is 65%.展开更多
文摘Bulk metallic glass Zr_52.5Ni_14.6Al_10Cu_17.9Ti_5 was prepared by melt injection casting method. Its glass transition and crystallization temperatures were determined by differential scanning calorimetry (DSC) to be 631 K and 710 K respectively. By analysis of X-ray diffractometry (XRD) and transmission electron microscopy (TEM ), the predominant crystallized phase of Zr_2Ni0.67O0.33 distributed on glass state matrix was detected after annealing at 673 K for 600 s. The transformation to Zr_2Ni_0.67O_0.33 and a small amount of ZrAl and Zr_2Cu took place after annealing for 600 s at temperature from 703 K to 723 K. With increasing annealing temperature from 753 K to 823 K, the amounts of ZrAl and Zr_2Cu increased, but the size of the crystals did not significantly change. The transformation to Zr_2Ni_0.67O_0.33 is interface-controlled, but is diffusion-controlled to Zr_2Cu and ZrAl. With increasing annealing temperature up to 200 K above T_x, the nanometer grains became very fine because of the increase of nucleation rate for Zr_2Cu and ZrAl.
基金Funded by National Natural Science Foundation of China （No. 50875117）.
文摘In this paper, the vacuum brazing of Si3N4 ceramic was carried out with Ti40Zr25Ni15Cu20 amorphous filler metal. The interfacial microstructure was investigated by scanning electron microscopy （ SEM ）, energy dispersive spectroscopy （EDS） etc. According to the analysis, the interface reaction layer was mode up of TiN abut on the ceramic and the Ti-Si, Zr-Si compounds. The influence of brazing temperature and holding time on the joint strength was also studied. The results shows that the joint strength first increased and then decreased with the increasing of holding time and brazing temperature. The joint strength was significantly affected by the thickness of the reaction layer. Under the same experimental conditions, the joint brazed with amorphous filler metal exhibits much higher strength compared with the one brazed with crystalline filler metal with the same composition. To achieve higher joint strength at relatively low temperature, it is favorable to use the amorphous filler metal than the crystalline filler metal.
文摘The crystallization kinetics of Zr 41 Ti 14 Cu 12.5 Ni 10 Be 22.5 bulk metallic glass has been studied by using DSC and XRD. The results show that two exothermal peaks are observed when the alloy is heated to 500?℃, one peak results dominantly from the formation of Ti 2Ni ( α phase transition), the other peak is mainly due to the formation of Zr 2Cu ( β phase transition). At the beginning of the crystallization, the activation energy of the α phase is smaller, and it increases with increasing crystallized fraction ( x c). When x c increases to 90%, the crystallization activation energy shows the largest value (220?kJ/mol). The crystallization activation energy of the β phase remains about 227?kJ/mol, as it’s crystallized fraction is below 60%, and then it increases with increasing crystallized fraction, and shows the largest activation energy of 257?kJ/mol, as the x c is 65%.
