Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electroche...Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.展开更多
Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterize...Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.展开更多
Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The p...Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.展开更多
The Ti-Supported MnO_2 electrode was modified by introducing SnO_2+RuO_2+MnO_2 as an intermediate layer into the Ti/MnO_2 interface. The anodic polarization curves were measured at various temperatures ranging from 30...The Ti-Supported MnO_2 electrode was modified by introducing SnO_2+RuO_2+MnO_2 as an intermediate layer into the Ti/MnO_2 interface. The anodic polarization curves were measured at various temperatures ranging from 30 to 80℃ and the activation energy for the oxygen evolution reaction was evaluated. The experimental activation energy increased linearly with increasing the overpotential. The activation energy at the equilibrium potential was linearly correlated with the difference between the crystal field stabilization energies of Mn^(4+) at initial state and Mn^(4+) at transition state. The electrocatalysis characteristics of the anode were discussed by means of the mechanism of the substitution reaction of the ligand(S_N1 and S_N2) and molecular orbital theory. The results show that the anode has better electrocatalystic characteristics.展开更多
The characteristic of electrochemical oxidation of aniline on SnO 2/Ti electrode is studied. The results indicate that SnO 2/Ti electrode doped F plays a wonderful role in the oxidation of aniline comparing with...The characteristic of electrochemical oxidation of aniline on SnO 2/Ti electrode is studied. The results indicate that SnO 2/Ti electrode doped F plays a wonderful role in the oxidation of aniline comparing with Pt electrode. The kinetics factors that influence the oxidation rate of aniline on the SnO 2/Ti electrode are determined by the dissolving of the film on the electrode. The dissolving of the film consisted of intermediate products on the electrode is the slow step. The effects of aniline concentration, pH in aniline solution and the current density( i )on the rate of aniline oxidation, the complexity of intermediate products and the basic category of the intermediate products consisted of the film are introduced.展开更多
Au-Pt/SnO2/GC composite electrode was prepared by self-assembling Au-Pt nanoparticles on SnO2 film, which was deposited on actived glassy carbon （GC）. Atomic force microscopy （AFM） and scanning electron microscopy...Au-Pt/SnO2/GC composite electrode was prepared by self-assembling Au-Pt nanoparticles on SnO2 film, which was deposited on actived glassy carbon （GC）. Atomic force microscopy （AFM） and scanning electron microscopy （SEM） images revealed that dense and uniform Au-Pt particles with 25-nm diameter were dispersed on SnO2 film. X-ray photoelectron spectroscopy （XPS） results proved that there was an interaction between Au-Pt nanoparticles and SnO2 support. Electrochemical experiments showed that Au-Pt/SnOz/GC composite electrode had a good electrocatalytic activity to the oxidation of methanol展开更多
Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 ...Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.展开更多
为了研究满足压载水排放标准的处理系统,建立了可以实现单独控制的以钛基氧化锡钌(Ti/SnO2-RuO2)为阳极材料的电催化系统和紫外辐射复合压载水处理系统。以杜氏盐藻、青岛大扁藻、锥状克里斯普藻和四爿藻为目标处理微生物,对该系统进行...为了研究满足压载水排放标准的处理系统,建立了可以实现单独控制的以钛基氧化锡钌(Ti/SnO2-RuO2)为阳极材料的电催化系统和紫外辐射复合压载水处理系统。以杜氏盐藻、青岛大扁藻、锥状克里斯普藻和四爿藻为目标处理微生物,对该系统进行微藻灭活实验结果表明,Ti/SnO2-RuO2阳极电催化-UV复合系统克服了单独电催化系统高能耗、单独紫外辐射系统紫外灯衰减迅速的缺点,在紫外辐射出度45μW/cm2、电流密度130 m A/cm2、HRT为1.0 s的条件下,处理出水4 h后活藻数量可以达到国际海事组织(IMO)对压载水中10~50μm微生物的灭活要求。总剩余氧化物(TRO)含量会随时间推移而有衰减,且没有出现细胞光复活和修复现象,说明该复合系统具有理想的持续灭活作用。展开更多
Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be...Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.展开更多
The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electr...The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.展开更多
Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)como...Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).展开更多
基金supported by the National Natural Science Foundation of China(21507104)the Fundamental Research Funds for the Central Universities of China
文摘Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.
基金the Fund of the Natural Science of Guangxi (0731015)
文摘Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.
基金Project supported by the Institute of Environmental Engineering,Peking University and China Postdoctoral Science Foundation(No.2005037032)
文摘Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.
基金Supported by the National Natural Science Foundation of China.
文摘The Ti-Supported MnO_2 electrode was modified by introducing SnO_2+RuO_2+MnO_2 as an intermediate layer into the Ti/MnO_2 interface. The anodic polarization curves were measured at various temperatures ranging from 30 to 80℃ and the activation energy for the oxygen evolution reaction was evaluated. The experimental activation energy increased linearly with increasing the overpotential. The activation energy at the equilibrium potential was linearly correlated with the difference between the crystal field stabilization energies of Mn^(4+) at initial state and Mn^(4+) at transition state. The electrocatalysis characteristics of the anode were discussed by means of the mechanism of the substitution reaction of the ligand(S_N1 and S_N2) and molecular orbital theory. The results show that the anode has better electrocatalystic characteristics.
基金Supported by the National Natural Science Foundation of PRC( 10 9710 2 3)
文摘The characteristic of electrochemical oxidation of aniline on SnO 2/Ti electrode is studied. The results indicate that SnO 2/Ti electrode doped F plays a wonderful role in the oxidation of aniline comparing with Pt electrode. The kinetics factors that influence the oxidation rate of aniline on the SnO 2/Ti electrode are determined by the dissolving of the film on the electrode. The dissolving of the film consisted of intermediate products on the electrode is the slow step. The effects of aniline concentration, pH in aniline solution and the current density( i )on the rate of aniline oxidation, the complexity of intermediate products and the basic category of the intermediate products consisted of the film are introduced.
基金supported by the High-Tech Research and Development Program of China (No. 2007AA03Z219)the Funding Project for Academic Human Resources Development in Institutions of Higher Learning under the Jurisdiction of Beijing Municipality, and the Beijing Natural Science Foundation (No. 207001)
文摘Au-Pt/SnO2/GC composite electrode was prepared by self-assembling Au-Pt nanoparticles on SnO2 film, which was deposited on actived glassy carbon （GC）. Atomic force microscopy （AFM） and scanning electron microscopy （SEM） images revealed that dense and uniform Au-Pt particles with 25-nm diameter were dispersed on SnO2 film. X-ray photoelectron spectroscopy （XPS） results proved that there was an interaction between Au-Pt nanoparticles and SnO2 support. Electrochemical experiments showed that Au-Pt/SnOz/GC composite electrode had a good electrocatalytic activity to the oxidation of methanol
文摘Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.
文摘为了研究满足压载水排放标准的处理系统,建立了可以实现单独控制的以钛基氧化锡钌(Ti/SnO2-RuO2)为阳极材料的电催化系统和紫外辐射复合压载水处理系统。以杜氏盐藻、青岛大扁藻、锥状克里斯普藻和四爿藻为目标处理微生物,对该系统进行微藻灭活实验结果表明,Ti/SnO2-RuO2阳极电催化-UV复合系统克服了单独电催化系统高能耗、单独紫外辐射系统紫外灯衰减迅速的缺点,在紫外辐射出度45μW/cm2、电流密度130 m A/cm2、HRT为1.0 s的条件下,处理出水4 h后活藻数量可以达到国际海事组织(IMO)对压载水中10~50μm微生物的灭活要求。总剩余氧化物(TRO)含量会随时间推移而有衰减,且没有出现细胞光复活和修复现象,说明该复合系统具有理想的持续灭活作用。
基金National Natural Science Foundation of China with Grant No.21905304Natural Science Foundation of Shandong Province(No.ZR2019BEM031)the Fundamental Research Funds for the Central Universities(Nos.18CX02158A and 19CX05001A).
文摘Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.
文摘The electrochemical treatment of COD contained in biologically pretreated coking wastewater treated by a three-dimensional electrode system with modified coke as the particle electrode was investigated. And the electrochemical perromance of the coke modified with various active components was studied. The results show that the coke modified with Fe（NO3）2 has the lowest energy consumption and higher COD removal rate under the same condition, and the modified coke has better surface characteristics for the purpose of this study. In addition, the kinetic constant was also calculated. The study shows that the three-dimensional electrode system with Fe （NO3）z-modified coke can give a satisfactory solution in biologically pretreated coking wastewater.
基金Thanks to the financial support from the Science and technology project of Shaanxi Province(2017ZDXM-GY-041).
文摘Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).
