The mechanical behaviours of Ti-24Al-11Nb alloy in the brittle-ductile transition (BOT) have been investigated by using three-point bending tests. The temperature dependence of the fractal dimensions and fractal chara...The mechanical behaviours of Ti-24Al-11Nb alloy in the brittle-ductile transition (BOT) have been investigated by using three-point bending tests. The temperature dependence of the fractal dimensions and fractal characterization of fracture surfaces are presented. The probable mechanism controlling BDT of intermetallic alloys are proposed according to fractal geometry.Additionally. it is found that there is a positive relationship between the fractal dimension and fracture toughness in BDT for Ti-24Al-11Nb展开更多
In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The re...In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The results indicate that the(α2+O+B2) three-phase microstructure with equiaxed grains was acquired by Ti-22 Al-24 Nb alloy billet forging, and the average size of the grains was about 300 μm. With the increase of solution time, the primary lath-shaped O phase began to dissolve, and then the equiaxial α2 phase started to dissolve, but the undissolved α2/O phase began to be equiaxial and grow. The grains of original B2 phase recrystallized and grew. After the 2 h solution treatment, the recrystallization of grains was completed basically and the average size of the grains was about 100 μm. After the 2.5 h solution treatment, the strength of the alloy decreased, and the plasticity increased. However, when the solution treatment increased to 3 h, the plasticity decreased but the strength increased. The optimal solution parameters of Ti-22 Al-24 Nb alloy were the holding time of 2 h, the solution temperature of 1 000 ?C, and water cooling. Excellent comprehensive mechanical properties can be accquired under these parameters. The tensile strength, the yield strength, the elasticity modulus, the elongation, and the section shrinkage were 950 MPa, 915 MPa, 90 GPa, 15.69% and 42.28%, respectively.展开更多
For alloy Ti-24Al-11Nb,stress corrosion cracking(SCC) in methanol solution and hydrogen induced cracking(HIC) during dynamic charging at room temperature have been studied.Experiment has shown that the normalised thre...For alloy Ti-24Al-11Nb,stress corrosion cracking(SCC) in methanol solution and hydrogen induced cracking(HIC) during dynamic charging at room temperature have been studied.Experiment has shown that the normalised threshold stress intensities of SCC failure for various microstructures are KISCC/KC =0.53 0.69 and the threshold value for SCC arresting KISCC/ KIC=0.61-0.79.The threshold values of HIC during dynamic charging are close to that of SCC,but da/dt or fracture time of HIC is one to three orders of magnitude smaller or longer than that of SCC,respectively.The.fracture surface for HIC is also different from that for SCC.For the Ti-24Al-Nb alloy-methanol systein,a kind of inierphase SCC has been found For the microstructures resulting from furnace cooling,SCC initiated and propagated preferentially along theα2/βinterphase boundaries,displaying the microstructure on the fracture surface of SCC.However,there is no interphase SCC for the microstructure resulting from air cooling.展开更多
文摘The mechanical behaviours of Ti-24Al-11Nb alloy in the brittle-ductile transition (BOT) have been investigated by using three-point bending tests. The temperature dependence of the fractal dimensions and fractal characterization of fracture surfaces are presented. The probable mechanism controlling BDT of intermetallic alloys are proposed according to fractal geometry.Additionally. it is found that there is a positive relationship between the fractal dimension and fracture toughness in BDT for Ti-24Al-11Nb
基金Funded by the National Natural Science Foundation of China(No.51464035)
文摘In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The results indicate that the(α2+O+B2) three-phase microstructure with equiaxed grains was acquired by Ti-22 Al-24 Nb alloy billet forging, and the average size of the grains was about 300 μm. With the increase of solution time, the primary lath-shaped O phase began to dissolve, and then the equiaxial α2 phase started to dissolve, but the undissolved α2/O phase began to be equiaxial and grow. The grains of original B2 phase recrystallized and grew. After the 2 h solution treatment, the recrystallization of grains was completed basically and the average size of the grains was about 100 μm. After the 2.5 h solution treatment, the strength of the alloy decreased, and the plasticity increased. However, when the solution treatment increased to 3 h, the plasticity decreased but the strength increased. The optimal solution parameters of Ti-22 Al-24 Nb alloy were the holding time of 2 h, the solution temperature of 1 000 ?C, and water cooling. Excellent comprehensive mechanical properties can be accquired under these parameters. The tensile strength, the yield strength, the elasticity modulus, the elongation, and the section shrinkage were 950 MPa, 915 MPa, 90 GPa, 15.69% and 42.28%, respectively.
文摘For alloy Ti-24Al-11Nb,stress corrosion cracking(SCC) in methanol solution and hydrogen induced cracking(HIC) during dynamic charging at room temperature have been studied.Experiment has shown that the normalised threshold stress intensities of SCC failure for various microstructures are KISCC/KC =0.53 0.69 and the threshold value for SCC arresting KISCC/ KIC=0.61-0.79.The threshold values of HIC during dynamic charging are close to that of SCC,but da/dt or fracture time of HIC is one to three orders of magnitude smaller or longer than that of SCC,respectively.The.fracture surface for HIC is also different from that for SCC.For the Ti-24Al-Nb alloy-methanol systein,a kind of inierphase SCC has been found For the microstructures resulting from furnace cooling,SCC initiated and propagated preferentially along theα2/βinterphase boundaries,displaying the microstructure on the fracture surface of SCC.However,there is no interphase SCC for the microstructure resulting from air cooling.
