Fe/Mo composite coatings were prepared by air plasma spraying （APS） using Fe-based and Mo-based amorphous and nanocrys- talline mixed powders. Microstructural studies show that the composite coatings present a layer...Fe/Mo composite coatings were prepared by air plasma spraying （APS） using Fe-based and Mo-based amorphous and nanocrys- talline mixed powders. Microstructural studies show that the composite coatings present a layered structure with low porosity due to adding the self-bonded Mo-based alloy. Corrosion behaviors of the composite coatings, the Fe-based coatings and the Mo-based coatings were in- vestigated by electrochemical measurements and salt spray tests. Electrochemical results show that the composite coatings exhibit a lower polarization current density and higher corrosion potentials than the Fe-based coating when tested in 3.5wt% NaC1 solutions, indicating supe- rior corrosion resistance compared with the Fe-based coating. Also with the increase in addition of the Mo-based alloy, a raised corrosion re- sistance, inferred by an increase in corrosion potential and a decrease in polarization current density, can be found. The results of salt spray tests again show that the corrosion resistance is enhanced by adding the Mo-based alloy, which helps to reduce the porosity of the composite coatings and enhance the stability of the passive films.展开更多
The Effects of heat treatment temperature on the hardness,wear resistance and structure of the amorphous Ni-W-P-SiC composite coatings have been investigated.The results show that Ni-W-P-SiC composite coatings are amo...The Effects of heat treatment temperature on the hardness,wear resistance and structure of the amorphous Ni-W-P-SiC composite coatings have been investigated.The results show that Ni-W-P-SiC composite coatings are amorphous under 300℃, partially crystalline at 300-400℃,and crystalline when heat treatment temperature reaches 400℃,the crystals being fine Ni3P phase particles.The hardness,wear resistance and the crystallization temperature of the composite coatings increase when an additive is added into the bath.The hardness and wear resistance of the coatings increase with increasing heat treatment temperature,and they will reach their peak values when the heat treatment temperature reaches 400℃.Corrosion experiment indicates that the corrosion resistance of amorphous Ni-W-P-SiC composite coatings in various kinds of corrosive media except nitric acid is better than that of stainless steel 1Cr18Ni9Ti.Scanning electron microscopy observation shows that the additive has no effect on the surface appearance of the coatings,but the current density and the pH value have considerable effects on the surface appearance.展开更多
To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by las...To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.展开更多
Fe-based amorphous composite coatings were fabricated on AISI 1045 steel by laser cladding. The results of the X- ray diffraction and transmission electron microscopy analyses .show the coating is composed of an amorp...Fe-based amorphous composite coatings were fabricated on AISI 1045 steel by laser cladding. The results of the X- ray diffraction and transmission electron microscopy analyses .show the coating is composed of an amorphous phase in majority and a nanocrystaUine phuse in m,inority. Phase composition of the coating changes along the depth of the coating. The reasonable scanning speed for fabricating an amorphous composite coating is 3 500 mm/min when the laser power is 4 800 W and the laser beam diameter is 2 mm. If the scanning speed is lower than 3 500 mm/min, the intensity of the two main diffraction peaks in X-ray diffraction patterns of the coatings decreases with the scanning speeds increasing. At the same time, a broad halo peak emerges and enlarges. High laser power and fast scanning speed are the essential conditions of amorphization. The coating exhibits high microhardness.展开更多
To improve the surface properties of magnesium alloys, a study was conducted on Cu-Zr-A1 composite coatings on AZ91HP magnesium alloy by laser cladding. The influence of laser scanning speed on the microstructures and...To improve the surface properties of magnesium alloys, a study was conducted on Cu-Zr-A1 composite coatings on AZ91HP magnesium alloy by laser cladding. The influence of laser scanning speed on the microstructures and properties of the coatings was discussed. The coatings consist of amorphous phase, CusZr3, and Cul0ZrT. With the increase of laser scanning speed, the amorphous phase content of the coatings increases and reaches 60.56wt% with the laser scanning speed of 2.0 m/min. Because of the influence of laser scanning speed on the amorphous and crystal phases, the coatings show the maximum elastic modulus, hardness, and wear resistance at the laser scanning speed of 1.0 m/min. At the laser scanning speed of 2.0 m/min, the coatings have the best corrosion resistance.展开更多
Glass-coated amorphous FeCuNbSiB microwires were prepared by Taylor-Ulitovsky technique. X-ray diffractometry and scanning electron microscopy were used to investigate the microstructure and morphology of the glass-co...Glass-coated amorphous FeCuNbSiB microwires were prepared by Taylor-Ulitovsky technique. X-ray diffractometry and scanning electron microscopy were used to investigate the microstructure and morphology of the glass-coated microwires respectively. The vibrating sample magnetometer and vector network analyzer were used to study the magnetostatic and microwave properties of glass-coated microwires. The experimental results show that the effective anisotropy of an array of 150 microwires of 10 mm in length is large than that of one microwire of 10 mm in diameter and an array of 150 microwires of 1 mm in diameter. The natural ferromagnetic resonance takes place as the microwave magnetic component is perpendicular to the microwires axis, and the electric dipole resonance takes place as the microwire is long or the short microwire concentration is moderate. The natural ferromagnetic resonance shifts to higher frequency with the larger microwire concentration. The electric dipole resonance is governed by the microwires length and concentration. The glass-coated FeCuNbSiB microwires can be used to design EMI filters and microwave absorbing materials.展开更多
Cobalt-based amorphous/nanocrystalline composite coatings have been grown by arc ion plating together with a specimen cooling system. With decreasing substrate temperature, the coatings undergo significant structure e...Cobalt-based amorphous/nanocrystalline composite coatings have been grown by arc ion plating together with a specimen cooling system. With decreasing substrate temperature, the coatings undergo significant structure evolution. The degree of crystallization first decreases and subsequently increases as confirmed by X-ray diffraction. The cluster size first decreases and then remains constant as confirmed by transmission electron microscopy. The effect of substrate temperature on the evolution of the structure has been studied as a result of a competition between nucleation thermodynamics and kinetics of crystalline growth. With decreasing the substrate temperature, the microhardness and the critical load of the composite coatings firstly increased, and then remained almost constant. And the saturation magnetization revealed the opposite trend over the same range. The essence of these phenomena was ascribed to the microstructural variations caused by the decrease of the substrate temperature.展开更多
基金financially supported by the Special Fund for Basic Scientific Research of Central Colleges, Chang’an University (No.CHD2011JC126)the Special Fund for Basic Research Support Plan of Chang’an Universitythe Open Fund of the Engineering Research Center of Transportation Materials, Ministry of Education of China
文摘Fe/Mo composite coatings were prepared by air plasma spraying （APS） using Fe-based and Mo-based amorphous and nanocrys- talline mixed powders. Microstructural studies show that the composite coatings present a layered structure with low porosity due to adding the self-bonded Mo-based alloy. Corrosion behaviors of the composite coatings, the Fe-based coatings and the Mo-based coatings were in- vestigated by electrochemical measurements and salt spray tests. Electrochemical results show that the composite coatings exhibit a lower polarization current density and higher corrosion potentials than the Fe-based coating when tested in 3.5wt% NaC1 solutions, indicating supe- rior corrosion resistance compared with the Fe-based coating. Also with the increase in addition of the Mo-based alloy, a raised corrosion re- sistance, inferred by an increase in corrosion potential and a decrease in polarization current density, can be found. The results of salt spray tests again show that the corrosion resistance is enhanced by adding the Mo-based alloy, which helps to reduce the porosity of the composite coatings and enhance the stability of the passive films.
文摘The Effects of heat treatment temperature on the hardness,wear resistance and structure of the amorphous Ni-W-P-SiC composite coatings have been investigated.The results show that Ni-W-P-SiC composite coatings are amorphous under 300℃, partially crystalline at 300-400℃,and crystalline when heat treatment temperature reaches 400℃,the crystals being fine Ni3P phase particles.The hardness,wear resistance and the crystallization temperature of the composite coatings increase when an additive is added into the bath.The hardness and wear resistance of the coatings increase with increasing heat treatment temperature,and they will reach their peak values when the heat treatment temperature reaches 400℃.Corrosion experiment indicates that the corrosion resistance of amorphous Ni-W-P-SiC composite coatings in various kinds of corrosive media except nitric acid is better than that of stainless steel 1Cr18Ni9Ti.Scanning electron microscopy observation shows that the additive has no effect on the surface appearance of the coatings,but the current density and the pH value have considerable effects on the surface appearance.
基金supported by the Open Fund of the State Key Laboratory of Advanced Welding Production Technology in Harbin Institute of Technology,Chinathe Open Fund of the State Key Laboratory of Materials Processing and Die&Mould Technology in Huazhong University of Science and Technology,China
文摘To improve the sliding wear resistance of AZ91D magnesium alloy, Cu-based amorphous composite coatings made of CuaTTi34Zr11Nis and Cu47Ti34Zr11Ni8＋20 wt pct SiC powders were fabricated on AZ91D magnesium alloy by laser cladding, respectively. SEM （scanning electron microscopy）, EDS （energy dispersive X-ray spectroscopy）, XRD （X-ray diffraction） and TEM （transmission electron microscopy） techniques were employed to study the phases of the coatings. The results show that the coatings mainly consist of amorphous phase and different intermetallic compounds. The reason of formation of amorphous phase and the function of SiC particles were explained in details.
文摘Fe-based amorphous composite coatings were fabricated on AISI 1045 steel by laser cladding. The results of the X- ray diffraction and transmission electron microscopy analyses .show the coating is composed of an amorphous phase in majority and a nanocrystaUine phuse in m,inority. Phase composition of the coating changes along the depth of the coating. The reasonable scanning speed for fabricating an amorphous composite coating is 3 500 mm/min when the laser power is 4 800 W and the laser beam diameter is 2 mm. If the scanning speed is lower than 3 500 mm/min, the intensity of the two main diffraction peaks in X-ray diffraction patterns of the coatings decreases with the scanning speeds increasing. At the same time, a broad halo peak emerges and enlarges. High laser power and fast scanning speed are the essential conditions of amorphization. The coating exhibits high microhardness.
基金supported by the Doctoral Fund of Northeast Dianli University(No.BSJXM-201010)
文摘To improve the surface properties of magnesium alloys, a study was conducted on Cu-Zr-A1 composite coatings on AZ91HP magnesium alloy by laser cladding. The influence of laser scanning speed on the microstructures and properties of the coatings was discussed. The coatings consist of amorphous phase, CusZr3, and Cul0ZrT. With the increase of laser scanning speed, the amorphous phase content of the coatings increases and reaches 60.56wt% with the laser scanning speed of 2.0 m/min. Because of the influence of laser scanning speed on the amorphous and crystal phases, the coatings show the maximum elastic modulus, hardness, and wear resistance at the laser scanning speed of 1.0 m/min. At the laser scanning speed of 2.0 m/min, the coatings have the best corrosion resistance.
基金Project(50371029) supported by the National Natural Science Foundation of ChinaProject(NCET-04-0702) supported by the New Century Excellent Talents in University, China
文摘Glass-coated amorphous FeCuNbSiB microwires were prepared by Taylor-Ulitovsky technique. X-ray diffractometry and scanning electron microscopy were used to investigate the microstructure and morphology of the glass-coated microwires respectively. The vibrating sample magnetometer and vector network analyzer were used to study the magnetostatic and microwave properties of glass-coated microwires. The experimental results show that the effective anisotropy of an array of 150 microwires of 10 mm in length is large than that of one microwire of 10 mm in diameter and an array of 150 microwires of 1 mm in diameter. The natural ferromagnetic resonance takes place as the microwave magnetic component is perpendicular to the microwires axis, and the electric dipole resonance takes place as the microwire is long or the short microwire concentration is moderate. The natural ferromagnetic resonance shifts to higher frequency with the larger microwire concentration. The electric dipole resonance is governed by the microwires length and concentration. The glass-coated FeCuNbSiB microwires can be used to design EMI filters and microwave absorbing materials.
文摘Cobalt-based amorphous/nanocrystalline composite coatings have been grown by arc ion plating together with a specimen cooling system. With decreasing substrate temperature, the coatings undergo significant structure evolution. The degree of crystallization first decreases and subsequently increases as confirmed by X-ray diffraction. The cluster size first decreases and then remains constant as confirmed by transmission electron microscopy. The effect of substrate temperature on the evolution of the structure has been studied as a result of a competition between nucleation thermodynamics and kinetics of crystalline growth. With decreasing the substrate temperature, the microhardness and the critical load of the composite coatings firstly increased, and then remained almost constant. And the saturation magnetization revealed the opposite trend over the same range. The essence of these phenomena was ascribed to the microstructural variations caused by the decrease of the substrate temperature.
