Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron mic...Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.展开更多
The transmission electron microscopy was employed to investigate the microstructure of infrared brazed highstrength Ti alloy using the Ti-15Cu-15Ni filler metal. Coarse primary Ti2Ni and transformed β-Ti are observed...The transmission electron microscopy was employed to investigate the microstructure of infrared brazed highstrength Ti alloy using the Ti-15Cu-15Ni filler metal. Coarse primary Ti2Ni and transformed β-Ti are observed in the 300 s brazed specimen. Blocky Ti2Ni and eutectoid Ti2Cu intermetallics are disappeared from the joint with increasing the brazing time to 1800 s. Both acicular α-Ti and retained β-Ti dominate the entire brazed joint.展开更多
Microstructural evolution of infrared vacuum brazed CP-Ti using two Ti-based braze alloys,Ti-15Cu-15Ni and Ti-15Cu-25Ni,has been investigated.The infrared brazed joint consisted of eutectic Ti 2 Cu/Ti 2 Ni intermetall...Microstructural evolution of infrared vacuum brazed CP-Ti using two Ti-based braze alloys,Ti-15Cu-15Ni and Ti-15Cu-25Ni,has been investigated.The infrared brazed joint consisted of eutectic Ti 2 Cu/Ti 2 Ni intermetallic compounds and Ti-rich matrix.The eutectic Ti 2 Cu/Ti 2 Ni intermetallic compounds disappeared from the joint after being annealed at 900 C for 1 h.In contrast,the depletion rate of both Cu and Ni from the braze alloy into CP-Ti substrate at 750 C annealing was greatly decreased as compared with that annealed at 900 C.Blocky Ti 2 Cu/Ti 2 Ni phases were observed even if the specimen was annealed at 750 C for 15 h.Because the Ni content of the Ti-15Cu-25Ni braze alloy is much higher than that of the Ti-15Cu-15Ni alloy,the amount of eutectic Ti 2 Cu/Ti 2 Ni phases in Ti-15Cu-25Ni brazed joint is more than that in Ti-15Ci-15Ni brazed joint.However,similar microstructural evolution can be obtained from the infrared brazed joint annealed at various temperatures and/or time for both filler metals.展开更多
基金financially supported by the National Key R&D Program of China (No.2018YFA0707300)the Natural Science Foundation of Shanxi Province,China (No.201801D221131)+2 种基金the National Natural Science Foundation of China (Nos.51905372,51904206,51805359,52075359)Shanxi Province Science and Technology Major Project,China (No.20181102011)China Postdoctoral Science Foundation (No.2020M670705)。
文摘Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.
基金financial support of this research by the National Science Council(NSC),Taiwan,China,under the grant number 98-2221-E-002-052
文摘The transmission electron microscopy was employed to investigate the microstructure of infrared brazed highstrength Ti alloy using the Ti-15Cu-15Ni filler metal. Coarse primary Ti2Ni and transformed β-Ti are observed in the 300 s brazed specimen. Blocky Ti2Ni and eutectoid Ti2Cu intermetallics are disappeared from the joint with increasing the brazing time to 1800 s. Both acicular α-Ti and retained β-Ti dominate the entire brazed joint.
基金support of this research by the National Science Council(NSC),Taiwan,China (Grant No.NSC 99-2221-E-002-051)
文摘Microstructural evolution of infrared vacuum brazed CP-Ti using two Ti-based braze alloys,Ti-15Cu-15Ni and Ti-15Cu-25Ni,has been investigated.The infrared brazed joint consisted of eutectic Ti 2 Cu/Ti 2 Ni intermetallic compounds and Ti-rich matrix.The eutectic Ti 2 Cu/Ti 2 Ni intermetallic compounds disappeared from the joint after being annealed at 900 C for 1 h.In contrast,the depletion rate of both Cu and Ni from the braze alloy into CP-Ti substrate at 750 C annealing was greatly decreased as compared with that annealed at 900 C.Blocky Ti 2 Cu/Ti 2 Ni phases were observed even if the specimen was annealed at 750 C for 15 h.Because the Ni content of the Ti-15Cu-25Ni braze alloy is much higher than that of the Ti-15Cu-15Ni alloy,the amount of eutectic Ti 2 Cu/Ti 2 Ni phases in Ti-15Cu-25Ni brazed joint is more than that in Ti-15Ci-15Ni brazed joint.However,similar microstructural evolution can be obtained from the infrared brazed joint annealed at various temperatures and/or time for both filler metals.
