Effect of RF power on the properties of transparent conducting zirconium-doped zinc oxide films prepared by RF magnetron sputtering

Transparent and conducting zirconium-doped zinc oxide films with high transparency and relatively low resistivity have been successfully prepared by radio frequency （RF） msgnetron sputtering at room temperature, The RF power is varied from 75 to 150 W. At first the crystallinity and conductivity of the film are improved and then both of them show deterioration with the increase of the RF power, The lowest resistivity achieved is 2.07 × 10^-3Ωcm at an RF power of 100W with a Hall mobility of 16cm^2V^-1s^-1 and a carrier concentration of 1.95 × 10^20 cm^-3. The films obtained are polycryetalline with a hexagonal structure and a preferred orientation along the c-axis, All the films have a high transmittance of approximately 92% in the visible range. The optical band gap is about 3.33 eV for the films deposited at different RF powers.

Preparation and Characterization of Transparent Conductive Zinc Doped Tin Oxide Thin Films Prepared by Radio-frequency Magnetron Sputtering

High transparent and conductive thin films of zinc doped tin oxide （ZTO） were deposited on quartz substrates by the radio-frequency （RF） magnetron sputtering using a 12 wt% ZnO doped with 88 wt% SnO2 ceramic target.The effect of substrate temperature on the structural,electrical and optical performances of ZTO films has been studied.X-ray diffraction （XRD） results show that ZTO films possess tetragonal rutile structure with the preferred orientation of （101）.The surface morphology and roughness of the films was investigated by the atomic force microscope （AFM）.The electrical characteristic （including carrier concentration,Hall mobility and resistivity） and optical transmittance were studied by the Hall tester and UV- VIS,respectively.The highest carrier concentration of -1.144×1020 cm-3 and the Hall mobility of 7.018 cm2（V ·sec）-1 for the film with an average transmittance of about 80.0% in the visible region and the lowest resistivity of 1.116×10-2 Ω·cm were obtained when the ZTO films deposited at 250 oC.

Studies of Laser-induced-MOCVDZinc Oxide Films

hin films of ZnO were prepared using the double photobeams ultraviolet laserinduced-metallorganic chemical vapour deposition (MOCVD)technique. The struc-ture and transparent photoconductive properties of these films were investigated us-ing X-ray diffraction (XRD) , reflecting electron diffraction (RED) .scanning elec-tron microscopy (SEM) and ultraviolet visible absorption spectrometry (UV) .Theexperiments showed that the technique produced superior quality films of polycrys-tal ZnO_(1-x) (the O-vacancies in the ZnO lattice) , and possessed higher depositionrate, lower growth temperature conipared with CVD or MOCVD technique and thethin films had far better transparent photoconductive properties than tliose grownby the conventional CVD or MOCVD technique.

Structural,Morphological and Electrical Properties of In-Doped Zinc Oxide Nanostructure Thin Films Grown on p-Type Gallium Nitride by Simultaneous Radio-Frequency Direct-Current Magnetron Co-Sputtering

Zinc oxide （ZnO） is one of the most promising and frequently used semiconductor materials. In-doped nanos- tructure ZnO thin films are grown on p-type gallium nitride substrates by employing the simultaneous rf and dc magnetron co-sputtering technique. The effect of In-doping on structural, morphological and electrical properties is studied. The different dopant concentrations are accomplished by varying the direct current power of the In target while keeping the fixed radio frequency power of the ZnO target through the co-sputtering deposition technique by using argon as the sputtering gas at ambient temperature. The structural analysis confirms that all the grown thin films preferentially orientate along the c-axis with the wurtzite hexagonal crystal structure without having any kind of In oxide phases. The presenting Zn, 0 and In elements＇ chemical compositions are identified with EDX mapping analysis of the deposited thin films and the calculated M ratio has been found to decrease with the increasing In power. The surface topographies of the grown thin films are examined with the atomic force microscope technique. The obtained results reveal that the grown film roughness increases with the In power. The Hall measurements ascertain that all the grown films have n-type conductivity and also the other electrical parameters such as resistivity,mobility and carrier concentration are analyzed.

Influence of Tin Doping on the Photocatalytic Activity of Zinc Oxide Thin Films under UV Light

Pure ZnO and Sn-doped ZnO thin films were successfully prepared by the spray pyrolysis method onto glass substrates. The obtained films were characterized by XRD （X-ray diffraction）, SEM （scanning electron microscopy） and ultraviolet-visible spectroscopy. The XRD results showed that the FWHM of Sn-doped ZnO film increased due to the substitution of Sn for Zn, the tin doping within the film causes the ZnO crystallinity to deteriorate. The grains of the film doped with Sn using dibutyltin diacetate were found to be non-uniform distribution through the sample but those appeared to form ganglia-like hills in the case of pure ZnO film. Furthermore, the Sn-doped ZnO films were tested with respect to the photocatalysis in aqueous solutions of MG （malachite green） upon UV-light illumination and in darkness. It was found that Sn-doped ZnO films prepared under specific conditions showed a lower photocatalytic activity than that of pure ZnO films.

Deposition and Characterisation of Nitrogen-Doped Zinc Oxide Thin Films by MOCVD Using Zinc Acetate—Ammonium Acetate Precursor

The synthesis and comprehensive analysis of nitrogen-doped zinc oxide thin films grown from a compound precursor of zinc acetate and ammonium acetate has been reported. The precursor was processed in different ratios of the zinc acetate-ammonium acetate additives, and each combination was used to deposit a thin film using metalorganic chemical vapour deposition (MOCVD) method. The produced thin films were characterised using Rutherford backscattering (RBS) spectroscopy, uv-visible spectrometry, x-ray diffractometry, four point probe measurements and optical microscopy. The deposited thin films showed a fairly consistent zinc:oxygen:nitrogen ratio of 4.4:3.7:1, the film structures were quasicrystalline and the sheet resistivities were high, while other familiar characteristics like optical transmittance, bandgap, thermal stability, etc. were maintained in the grown films. Applications in device fabrication and active sensor devices were hence envisaged as the emergent potentials of the thin films.

Effects of annealing process on characteristics of fully transparent zinc tin oxide thin-film transistor

Annealing effect on the performance of fully transparent thin-film transistor （TTFT）, in which zinc tin oxide （ZnSnO） is used as the channel material and SiO2 as the gate insulator, is investigated. The ZnSnO active layer is deposited by radio frequency magnetron sputtering while a SiO2 gate insulator is formed by plasma-enhanced chemical vapor deposition. The saturation field-effect mobility and on/off ratio of the TTFT are improved by low temperature annealing in vacuum. Maximum saturation field-effect mobility and on/off ratio of 56.2 cm2/（V.s） and 3×10^5 are obtained, respectively. The transfer characteristics of the ZnSnO TPT are simulated using an analytical model and good agreement between measured and the calculated transfer characteristics is demonstrated.

Temperature-dependent bias-stress-induced electrical instability of amorphous indium-gallium-zinc-oxide thin-film transistors

The time and temperature dependence of threshold voltage shift under positive-bias stress（PBS） and the following recovery process are investigated in amorphous indium-gallium-zinc-oxide（a-IGZO） thin-film transistors. It is found that the time dependence of threshold voltage shift can be well described by a stretched exponential equation in which the time constant τ is found to be temperature dependent. Based on Arrhenius plots, an average effective energy barrier Eτ stress= 0.72 eV for the PBS process and an average effective energy barrier Eτ recovery= 0.58 eV for the recovery process are extracted respectively. A charge trapping/detrapping model is used to explain the threshold voltage shift in both the PBS and the recovery process. The influence of gate bias stress on transistor performance is one of the most critical issues for practical device development.

Review of flexible and transparent thin-film transistors based on zinc oxide and related materials

Flexible and transparent electronics enters into a new era of electronic technologies.Ubiquitous applications involve wearable electronics,biosensors,flexible transparent displays,radio-frequency identifications（RFIDs）,etc.Zinc oxide（ZnO） and relevant materials are the most commonly used inorganic semiconductors in flexible and transparent devices,owing to their high electrical performances,together with low processing temperatures and good optical transparencies.In this paper,we review recent advances in flexible and transparent thin-film transistors（TFTs） based on ZnO and relevant materials.After a brief introduction,the main progress of the preparation of each component（substrate,electrodes,channel and dielectrics） is summarized and discussed.Then,the effect of mechanical bending on electrical performance is highlighted.Finally,we suggest the challenges and opportunities in future investigations.

Improvement in the electrical performance and bias-stress stability of dual-active-layered silicon zinc oxide/zinc oxide thin-film transistor

Si-doped zinc oxide（SZO） thin films are deposited by using a co-sputtering method,and used as the channel active layers of ZnO-based TFTs with single and dual active layer structures.The effects of silicon content on the optical transmittance of the SZO thin film and electrical properties of the SZO TFT are investigated.Moreover,the electrical performances and bias-stress stabilities of the single- and dual-active-layer TFTs are investigated and compared to reveal the effects of the Si doping and dual-active-layer structure.The average transmittances of all the SZO films are about 90% in the visible light region of 400 nm-800 nm,and the optical band gap of the SZO film gradually increases with increasing Si content.The Si-doping can effectively suppress the grain growth of ZnO,revealed by atomic force microscope analysis.Compared with that of the undoped ZnO TFT,the off-state current of the SZO TFT is reduced by more than two orders of magnitude and it is 1.5 × 10^-12 A,and thus the on/off current ratio is increased by more than two orders of magnitude.In summary,the SZO/ZnO TFT with dual-active-layer structure exhibits a high on/off current ratio of 4.0 × 10^6 and superior stability under gate-bias and drain-bias stress.

Double-layer indium doped zinc oxide for silicon thin-film solar cell prepared by ultrasonic spray pyrolysis

Indium doped zinc oxide （ZnO：In） thin films were prepared by ultrasonic spray pyrolysis on corning eagle 2000 glass substrate. 1 and 2 at.% indium doped single-layer ZnO：In thin films with different amounts of acetic acid added in the initial solution were fabricated. The 1 at.% indium doped single-layers have triangle grains. The 2 at.% indium doped single-layer with 0.18 acetic acid adding has the resistivity of 6.82 × 10^-3 Ω. cm and particle grains. The doublelayers structure is designed to fabricate the ZnO：In thin film with low resistivity （2.58 × 10^-3 Ω. cm） and good surface morphology. It is found that the surface morphology of the double-layer ZnO：In film strongly depends on the substratelayer, and the second-layer plays a large part in the resistivity of the doublewlayer ZnO：In thin film. Both total and direct transmittances of the double-layer ZnO：In film are above 80% in the visible light region. Single junction a-Si：H solar cell based on the double-layer ZnO：In as front electrode is also investigated.

Spray Pyrolysis Deposition of Single and Mixed Oxide Thin Films

The influence of processing parameters is investigated on the structural characteristics of single and mixed oxides produced by spray pyrolysis technique. The films were synthesized by spraying precursor solutions through a noz-zle onto a heated alumina substrate. The precursor consisted separately of aqueous solutions of tin chloride for SnO2 and zinc chloride for ZnO for single oxide cases, and aqueous solutions of tin chloride and indium nitrate for SnO2 + In2O3 and zinc chloride and indium nitrate solutions for ZnO + In2O3 for mixed oxide cases. The substrate temperature was varied accordingly for each single and mixed case. The films produced were characterized by X-ray Photoelectron Spectroscopy and Scanning Electron Microscopy. The results indicate that a non-homogenous film is formed at low temperature for both single oxides considered. The temperature has significant effect on the composition of the synthesized films of both single oxides below 450℃. The results for mixed oxides show that the best homogeneous films are obtained for 80 wt% ZnO + 20 wt% In2O3, and 80 wt% SnO2 + 20 wt% In2O3.

Low-Frequency Noise in Amorphous Indium Zinc Oxide Thin Film Transistors with Aluminum Oxide Gate Insulator

Low-frequency noise（LFN） in all operation regions of amorphous indium zinc oxide（a-IZO） thin film transistors（TFTs） with an aluminum oxide gate insulator is investigated. Based on the LFN measured results, we extract the distribution of localized states in the band gap and the spatial distribution of border traps in the gate dielectric,and study the dependence of measured noise on the characteristic temperature of localized states for a-IZO TFTs with Al2 O3 gate dielectric. Further study on the LFN measured results shows that the gate voltage dependent noise data closely obey the mobility fluctuation model, and the average Hooge＇s parameter is about 1.18×10^-3.Considering the relationship between the free carrier number and the field effect mobility, we simulate the LFN using the △N-△μ model, and the total trap density near the IZO/oxide interface is about 1.23×10^18 cm^-3eV^-1.

Synthesis and Characterization of Metal Organic Chemical Vapour Deposited Chromium Doped Zinc Oxide Thin Film for Gas Sensing Applications

Chromium (Cr) doped Zinc oxide ZnO thin films were deposited onto glass substrates by Metal Organic Chemical Vapour Deposition (MOCVD) technique with varying dopant concentration at a temperature of 420°C. The effect of the chromium concentration on morphological, structural, optical, electrical and gas sensing properties of the films were investigated. The scanning electron microscopy results revealed that the Cr concentration has great influence on the crystallinity, surface smoothness and grain size. X-ray diffraction (XRD) studies shows that films were polycrystalline in nature and grown as a hexagonal wurtzite structure. A direct optical band energy gap of 3.32 to 3.10 eV was obtained from the optical measurements. The transmission was found to decrease with increasing Cr doping concentration. Rutherford Backscattering Spectroscopy (RBS) analysis also demonstrates that Cr ions are substitutionally incorporated into ZnO. I-V characteristic of the film shows a resistivity ranges from 1.134 × 10-2 · cm to 1.24 × 10-2 · cm at room temperature. The gas sensing response of the films were enhanced with incorporation of Cr as a dopant with optimum operating temperature around 200°C.

Contact resistance asymmetry of amorphous indium–gallium–zinc–oxide thin-film transistors by scanning Kelvin probe microscopy

In this work, a method based on scanning Kelvin probe microscopy is proposed to separately extract source/drain（S/D） series resistance in operating amorphous indium–gallium–zinc–oxide（a-IGZO） thin-film transistors. The asymmetry behavior of S/D contact resistance is deduced and the underlying physics is discussed. The present results suggest that the asymmetry of S/D contact resistance is caused by the difference in bias conditions of the Schottky-like junction at the contact interface induced by the parasitic reaction between contact metal and a-IGZO. The overall contact resistance should be determined by both the bulk channel resistance of the contact region and the interface properties of the metalsemiconductor junction.

High-throughput fabrication and semi-automated characterization of oxide thin film transistors

High throughput experimental methods are known to accelerate the rate of research,development,and deployment of electronic materials.For example,thin films with lateral gradients in composition,thickness,or other parameters have been used alongside spatially-resolved characterization to assess how various physical factors affect the material properties under varying measurement conditions.Similarly,multi-layer electronic devices that contain such graded thin films as one or more of their layers can also be characterized spatially in order to optimize the performance.In this work,we apply these high throughput experimental methods to thin film transistors(TFTs),demonstrating combinatorial channel layer growth,device fabrication,and semi-automated characterization using sputtered oxide TFTs as a case study.We show that both extrinsic and intrinsic types of device gradients can be generated in a TFT library,such as channel thickness and length,channel cation compositions,and oxygen atmosphere during deposition.We also present a semi-automated method to measure the 44 devices fabricated on a 50 mm×50 mm substrate that can help to identify properly functioning TFTs in the library and finish the measurement in a short time.Finally,we propose a fully automated characterization system for similar TFT libraries,which can be coupled with high throughput data analysis.These results demonstrate that high throughput methods can accelerate the investigation of TFTs and other electronic devices.

Positive gate bias stress-induced hump-effect in elevated-metal metal-oxide thin film transistors

Under the action of a positive gate bias stress, a hump in the subthreshold region of the transfer characteristic is observed for the amorphous indium-gallium-zinc oxide thin film transistor, which adopts an elevated-metal metal-oxide structure. As stress time goes by, both the on-state current and the hump shift towards the negative gate-voltage direction. The humps occur at almost the same current levels for devices with different channel widths, which is attributed to the parasitic transistors located at the channel width edges. Therefore, we propose that the positive charges trapped at the back-channel interface cause the negative shift, and the origin of the hump is considered as being due to more positive charges trapped at the edges along the channel width direction. On the other hand, the hump-effect becomes more significant in a short channel device （L=2 μm）. It is proposed that the diffusion of oxygen vacancies takes place from the high concentration source/drain region to the intrinsic channel region.

Influence of oxygen gas content on the structural and optical properties of ZnO thin films deposited by RF magnetron sputtering at room temperature

Zinc oxide （ZnO） thin films were deposited on sapphire （0001） substrates at room temperature by radiofrequency （RF） magnetron sputtering at oxygen gas contents of 0%, 25%, 50% and 75%, respectively. The influence of oxygen gas content on the structural and optical properties of ZnO thin films was studied by a surface profile measuring system, X-ray diffraction analysis, atomic force microscopy, and UV spectro- photometry. It is found that the size of ZnO crystalline grains increases first and then decreases with the increase of oxygen gas content, and the maximum grain size locates at the 25% oxygen gas content. The crystalline quality and average optical transmittance （〉90%） in the visi- ble-light region of the ZnO film prepared at an oxygen gas content of 25% are better than those of ZnO films at the other contents. The obtained results can be attributed to the resputtefing by energetic oxygen anions in the growing process.

Photocatalytic degradation of methyl orange over ITO/CdS/ZnO interface composite films

ITO/CdS/ZnO interface composite films were successfully prepared by subsequent electrodeposition of CdS and ZnO onto indium tin oxide （ITO） glass substrates. The obtained ITO/CdS/ZnO composite films were characterized with X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and UV-Vis spectroscopy. The photocatalytic activity of ITO/CdS/ZnO composite films were investigated using methyl orange （MO） as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including initial concentration of MO, pH value of solution, and inorganic anion species over the composite films were examined. A blue shift of absorption threshold was observed for the ITO/CdS/ZnO film in comparison with ITO/ZnO film. ITO/CdS/ZnO composite films prepared under specific conditions showed a higher photocatalytic activity than that of ITO/ZnO films. It was also found that the photocatalytic degradation of MO on the composite films followed pseudo-first order kinetics.