Microstructure and mechanical properties of laser additive repaired Ti17 titanium alloy

Laser additive manufacturing technology with powder feeding was employed to repair wrought Ti17titanium alloy with small surface defects.The microstructure,micro-hardness and room temperature tensile properties of laser additive repaired(LARed)specimen were investigated.The results show that,cellular substructures are observed in the laser deposited zone(LDZ),rather than the typicalαlaths morphology due to lack of enough subsequent thermal cycles.The cellular substructures lead to lower micro-hardness in the LDZ compared with the wrought substrate zone which consists of duplex microstructure.The tensile test results indicate that the tensile deformation process of the LARed specimen exhibits a characteristic of dramatic plastic strain heterogeneity and fracture in the laser repaired zone with a mixed dimple and cleavage mode.The tensile strength of the LARed specimen is slightly higher than that of the wrought specimen and the elongation of11.7%is lower.

Effects of Ce and Ti on the microstructures and mechanical properties of an Al-Cu-Mg-Ag alloy

The effects of Ce and Ti additions on the microstructures and mechanical properties of an Al-Cu-Mg-Ag alloy have been studied, It has been shown that either Ce or Ti can decrease the as-cast grain size of the Al-Cu-Mg-Ag alloy, increase the nucleation ratio for Ω phase as heterogeneous nucleation centers, inhibit the growth of Ω phase during aging, and thus increase the volume fraction and decrease the spacing of Ω phase. These microstructures increase the yield strength and tensile strength. However, if both Ce and Ti are added to the alloy, they form （Ce,Ti）-contained compounds and increase the grain size during casting, but have no effects on the nucleation and the growth of Ω phase during aging. The alloy containing both Ce and Ti has a relatively lower Vicks hardness and strength compared to the alloy containing either Ce or Ti.

Influence of heat treatments on microstructure and mechanical properties of laser additive manufacturing Ti-5Al-2Sn-2Zr-4Mo-4Cr titanium alloy

The effect of heat treatments on laser additive manufacturing(LAM)Ti-5Al-2Sn-2Zr-4Mo-4Cr titanium alloy(TC17)was studied aiming to optimize its microstructure and mechanical properties.The as-deposited sample exhibits features of a mixed priorβgrain structure consisting of equiaxed and columnar grains,intragranular ultra-fineαlaths and numerous continuous grain boundaryα(αGB).After being pre-annealed inα+βregion(840°C)and standard solution and aging treated,the continuousαGB becomes coarser and the precipitate free zone(PFZ)nearby theαGB transforms into a zone filled with ultra-fine secondaryα(αS)but no primaryα(αP).When pre-annealed in singleβregion(910°C),allαphases transform intoβphase and the alloying elements distribute uniformly near the grain boundary.DiscontinuousαGB and uniform mixture ofαP andαS near grain boundary form after subsequent solution and aging treatment.The two heat treatments can improve the tensile mechanical properties of LAM TC17to satisfy the aviation standard for TC17.

Effect of solution plus aging heat treatment on microstructural evolution and mechanical properties of near-β titanium alloy

The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.

Microstructures and mechanical properties of Ti−Al−V−Nb alloys with cluster formula manufactured by laser additive manufacturing

Ti−Al−V−Nb alloys with the cluster formula,12[Al−Ti_(12)](AlTi_(2))+5[Al−Ti1_(4)](V,Nb)2Ti,were designed by replacing V with Nb based on the Ti−6Al−4V alloy.Single-track cladding layers and bulk samples of the alloys with Nb contents ranging from 0 to 6.96 wt.%were prepared by laser additive manufacturing to examine their formability,microstructure,and mechanical properties.For single-track cladding layers,the addition of Nb increased the surface roughness slightly and decreased the molten pool height to improve its spreadability.The alloy,Ti−5.96Al−1.94V−3.54Nb(wt.%),exhibited better geometrical accuracy than the other alloys because its molten pool height was consistent with the spread layer thickness of the powder.The microstructures of the bulk samples contained similar columnar β-phase grains,regardless of Nb content.These grains grew epitaxially from the Ti substrate along the deposition direction,with basket-weaveα-phase laths within the columnar grains.Theα-phase size increased with increasing Nb contents,but its uniformity decreased.Along the deposition direction,the Vickers hardness increased from the substrate to the surface.The Ti−5.96Al−1.94V−3.54Nb alloy exhibited the highest Vickers hardness regardless of deposition position because of the optimal matching relationship between theα-phase size and its content among the designed alloys.

Effects of Ti addition on the microstructure and mechanical properties of Mg-Zn-Zr-Ca alloys

The effects of Ti additions(0,0.4,0.6,0.8,1.0,1.2 wt.%)on the microstructure and mechanical properties of as-cast and aging Mg-0.4%Zn-1.0%Zr-1.5%Ca(wt.%)alloys were investigated.The results indicated that minor Ti can effectively refine grains,while excessive Ti addition resulted in the grain coarsening.When the content of Ti was 0.8 wt.%,the as-cast alloy exhibited the finest grain size of 39μm which contributed to the optimal mechanical properties with Brinell hardness of 57.9 HB,ultimate tensile strength of 145 MPa and elongation of 3.2%.After T6 heat treatment,the continuous net-like Mg_(2)Ca and Mg_(6)Zn_(3)Ca_(2)phases changed to uniform massive T phases(ternary Mg-Zn-Ca phases)and dispersive halo-like precipitates(Mg_(2)Ca and Mg_(6)Zn_(3)Ca_(2)phases).The ultimate tensile strengths of the alloy at room temperature(RT),175℃and 200℃were correspondingly improved to 182 MPa,169 MPa and 141 MPa,respectively.

Microstructure and mechanical properties of Ti−Nb−Fe−Zr alloys with high strength and low elastic modulus

Zr was added to Ti−Nb−Fe alloys to develop low elastic modulus and high strengthβ-Ti alloys for biomedical applications.Ingots of Ti−12Nb−2Fe−(2,4,6,8,10)Zr(at.%)were prepared by arc melting and then subjected to homogenization,cold rolling,and solution treatments.The phases and microstructures of the alloys were analyzed by optical microscopy,X-ray diffraction,and transmission electron microscopy.The mechanical properties were measured by tensile tests.The results indicate that Zr and Fe cause a remarkable solid-solution strengthening effect on the alloys;thus,all the alloys show yield and ultimate tensile strengths higher than 510 MPa and 730 MPa,respectively.Zr plays a weak role in the deformation mechanism.Further,twinning occurs in all the deformed alloys and is beneficial to both strength and plasticity.Ti−12Nb−2Fe−(8,10)Zr alloys with metastableβphases show low elastic modulus,high tensile strength,and good plasticity and are suitable candidate materials for biomedical implants.

Microstructure evolution and mechanical properties of laser additive manufactured Ti-5Al-2Sn-2Zr-4Mo-4Cr alloy

The microstructure, microhardness and tensile properties of laser additive manufactured (LAM) Ti?5Al?2Sn?2Zr?4Mo?4Cr alloy were investigated. The result shows that the microstructure evolution is strongly affected by the thermal history of LAM process. Primary α (αp) with different morphologies, secondary α (αs) and martensite α' can be observed at different positions of the LAMed specimen. Annealing treatment can promote the precipitation of rib-like α phase or acicular α phase. As a result, it can increase or decrease the microhardness. The as-deposited L-direction and T-direction specimens contain the same phase constituent with different morphologies. The tensile properties of the as-deposited LAMed specimens are characterized of anisotropy. The L-direction specimen shows the character of low strength but high ductility when compared with the T-direction specimen. After annealing treatment, the strength of L-direction specimen increases significantly while the ductility reduces. The strength of the annealed T-direction specimen changes little, however, the ductility reduces nearly by 50%.

Effect of TiB2 and Al3Ti on the microstructure,mechanical properties and fracture behaviour of near eutectic Al−12.6Si alloy

A near eutectic Al−12.6Si alloy was developed with 0.0wt%,2.0wt%,4.0wt%,and 6.0wt%Al−5Ti−1B master alloy.The micro-structural morphology,hardness,tensile strength,elongation,and fracture behaviour of the alloys were studied.The unmodified Al−12.6Si al-loy has an irregular needle and plate-like eutectic silicon(ESi)and coarse polygonal primary silicon(PSi)particles in the matrix-likeα-Al phase.The P_(Si),E_(Si),andα-Al morphology and volume fraction were changed due to the addition of the Al−5Ti−1B master alloy.The hardness,UTS,and elongation improved due to the microstructural modification.Nano-sized in-situ Al3Ti particles and ex-situ TiB_(2)particles caused the mi-crostructural modification.The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time.The Al−5Ti−1B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.

Heat-treated microstructure and mechanical properties of laser solid forming Ti-6Al-4V alloy

The effects of heat treatment on the microstructure and mechanical properties of laser solid forming （LSF） Ti-6Al-4V alloy were investigated The influences of the temperature and time of solution treatment and aging treatment were analyzed. The results show that the microstructure of LSFed samples consists of Widmanstatten α laths and a little acicular in columnar prior β grains with an average grain width of 300 μm, which grow epitaxiaUy from the substrate along the deposition direction （27）. Solution treatment had an important effect on the width, aspect ratio, and volmne fraction of primary and secondary a laths, and aging treatment mainly affects the aspect ratio and volume fraction of primary α laths and the width and volume fraction of secondary a laths. Globular a phase was first observed in LSFed samples when the samples were heat treated with solution treatment （950℃, 8 h/air cooling （AC）） or with solution treatment （950℃, 1 h/AC） and aging treatment （550℃, above 8 h/AC）, respectively. The coarsening and globularization mechanisms of a phase in LSFed Ti-6Al-4V alloy during heat treatment were presented. To obtain good integrated mechanical properties for LSFed Ti-6Al-4V alloys, an optimized heat treatment regimen was suggested.

Influence of Al-Ti-B addition on the microstructure and mechanical properties of A356 alloys

The mechanical properties (σb,σ0.2,and δ) and fracture behavior of tensile specimens of the refined A356 alloys were investigated as a function of the addition level of Al-Ti-B master alloy under both as-cast and T6 heat-treated conditions. The results show that as the addition level of Al-5Ti-1B master alloy increases from 0.1 wt.% to 5.0 wt.%,the mechanical properties of refined A356 alloys improve steadily and then decrease slightly under both as-cast and T6 heat-treated conditions. Also,they display exc...

Erratum to: New high-strength Ti–Al–V–Mo alloy: from high-throughput composition design to mechanical properties

Erratum to:International Journal of Minerals, Metallurgy and Materials Volume 26, Number 9, September 2019, Page 1151https://doi.org/10.1007/s12613-019-1854-1The original version of this article unfortunately contained a mistake. The presentation of Fig. 11 was incorrect. The correct version is given below:

Microstructure and Mechanical Properties of Ultrafine Grained Mg15Al Alloy Processed by Equal-channel Angular Pressing

An as-cast magnesium alloy with high Al content Mg15Al was subjected to equal-channel angular pressing （ECAP） through a die with an angle of φ= 90？ at 553 K following route Bc. It is found that the network β-Mg17Al12 phases in the as-cast Mg15Al alloy are broken into small blocks and dispersed uniformly with increasing numbers of pressing passes. Moreover, many nano-sized Mg17Al12 particles precipitate in the ultra-fine α-Mg matrix. The grains are obviously refined. However, the grain structure is inhomogeneous in different areas of the alloy. The average size of the primary phase α-Mg is reduced to about 1 μm while grains of around 0.1-0.2 μm are obtained in some two-phase areas. With additional ECAP passes （up to 8）, coarsening of the grains occurs by dynamic recovery. Room temperature tensile tests show that the mechanical properties of Mg15Al alloys are markedly improved after 4 ECAP passes. The ultimate tensile strength and elongation to failure increase from 150 MPa to 269.3 MPa and from 0.05% to 7.4%, respectively. Compared with that after 4 passes, the elongation to failure of the alloy increases but the strength of the alloy slightly decreases after 8 ECAP passes. Fracture morphology of the ECAP-processed alloy exhibits dimple-like fracture characteristics while the as-cast alloy shows quasi-cleavage fractures.

Effects of Ta addition on the microstructure and mechanical properties of Ti_(40)Zr_(25)Ni_8Cu_9Be_(18) amorphous alloy

The effects of Ta addition on the microstructure and mechanical properties of Ti40Zr25Ni8Cu9Be18 bulk amorphous alloy were investigated by using X-ray diffraction (XRD), transmission electron microscopy (TEM), scan electron microscopy (SEM) and compressive testing. As a result, the addition of Ta (0-8at%) prompted the successive precipitation of quasicrystalline phase, CuTi2 phase and bcc β-Ti solid solution. Additionally, the addition of less Ta content (3at%-5at%) led to the formation of amorphous ma- trix/nanoquasicrystal/CuTi2 complex phase structure; and nanoquasicrystals, as reinforcement precipitates, improved the fracture strength of Ti-Zr-Ni-Cu-Be-Ta alloys, which led to the high compressive fracture strength 1856 MPa of Ta5 alloy. With increasing Ta content (5at%-8at%), although the ductile dendritic β-Ti solid solution was precipitated, the strength and plasticity decreased to a great extent resulting from the growth of quasicrystalline phase and CuTi2 phase.

Microstructure and Mechanical Properties of Cross-rolled Ti_(50)Ni_(47)Fe_3 Shape Memory Alloy

The microstructures, the phase transformation characteristics, and the mechanical properties of the Ti50Ni47Fe3 alloy in as-forged and as-cross-rolled states were investigated. It is found that, after cross-rolling, the phase transformation temperature （Ms） of the alloy decreases drastically and the grains get refined. Moreover, its yield strength and fracture strength after cross-rolling hit 540 MPa and 687 MPa respectively, up by about 200 MPa over those in as-forged state.

Microstructure and Mechanical Properties of Two-phaseTiAl Alloys in Lamellar Form

In two-phase TiAl alloys, the lamellar structures are of special interest and importance since they are so common and persistent. not only under as-cast conditions but also after thermal treatment. However. the lamellar structures are still poor in ductility,although they are beneficial for toughness and high temperature strength. This article will review the recent progress made in understanding the basic mechanical properties of the γ and α2 phases which comprise the two-phase alloys in Iamellar form, and discuss how an improved balance of strength and ductillty in the lamellar form may be achieved

New high-strength Ti–Al–V–Mo alloy: from high-throughput composition design to mechanical properties

The high-throughput diffusion-multiple technique and thermodynamics databases were used to design new high-strength Ti alloys. The composition–microstructure–property relationships of the Ti64–xMo alloys were obtained. The phase fraction and composition of the α and β phases of the Ti64–xMo alloys were calculated using the Thermo-Calc software. After aging at 600℃, the Ti64–6 Mo alloy precipitated ultrafine α phases. This phenomenon was explained on the basis of the pseudo-spinodal mechanism by calculating the Gibbs energy curves of the α and β phases of the Ti64–xMo alloys at 600℃. Bulk forged Ti64–6 Mo alloy exhibited high strength and moderate plasticity after α/β-phase-field solution treatment plus aging. The tensile properties of the alloy were determined by the size and morphology of the primary and secondary α phases and by the β grain size.

Effects of high-pressure rheo-squeeze casting on the Fe-rich phases and mechanical properties of Al-17Si-(1,1.5)Fe alloys

The effects of high pressure rheo-squeeze casting(HPRC) on the Fe-rich phases(FRPs) and mechanical properties of Al-17 Si-(1,1.5)Fe alloys were investigated. The alloy melts were first treated by ultrasonic vibration(UV) and then formed by high-pressure squeeze casting(HPSC). The FRPs in the as-cast HPSC Al-17 Si-1 Fe alloys only contained a long, needle-shaped β-Al5 Fe Si phase at 0 MPa. In addition to the β-Al5 Fe Si phase, the HPSC Al-17 Si-1.5 Fe alloy also contained the plate-shaped δ-Al4 Fe Si2 phase. A fine, block-shaped δ-Al4 Fe Si2 phase was formed in the Al-17 Si-1 Fe alloy treated by UV. The size of FRPs decreased with increasing pressure. After UV treatment, solidification under pressure led to further refinement of the FRPs. Considering alloy samples of the same composition, the ultimate tensile strength(UTS) of the HPRC samples was higher than that of the HPSC samples, and the UTS increased with increasing pressure. The UTS of the Al-17 Si-1 Fe alloy formed by HPSC exceeded that of the Al-17 Si-1.5 Fe alloy formed in the same manner under the same pressure. Conversely, the UTS of the Al-17 Si-1 Fe alloy formed by HPRC decreased to a value lower than that of the Al-17 Si-1.5 Fe alloy formed in the same manner.

Mechanical properties of rapidly solidified Al-Ti alloys after thermal exposure

Mechanical properties, for example the elastic modulus, yield stress and ultimate tensile stress, of the rapidly solidified (RS) Al Ti alloy after thermal exposure have been investigated using an Instron tensile test machine at a strain rate of 1.5×10 -4 s -1 . The results show that the elastic modulus of the Al Ti alloy increases with increasing Ti concentration, which can be predicted with Halpin Tsai equation, Eshelby method and hereby re modified shear lag model; the yield strength and the ultimate tensile stress increase with increasing volume fraction and decreasing particle size of the Al 3Ti and fine grain strengthening is suggested to be the main operative strengthening mechanism.

Effect of cerium on microstructure,wetting and mechanical properties of Ag-Cu-Ti filler alloy

Effect of cerium on microstructure,mechanical and wetting properties of Ag-Cu-Ti filler alloy was researched with optical microscopy,scanning electron microscopy and X-ray diffraction.The results indicated that addition of cerium accelerated alloying of the filler alloy,enlarged supercooled region,caused microstructural refinement and dispersed distribution of intermetallic compounds.It resulted in the increase in microhardness and shear strength of Ag-Cu-Ti filler alloy.At the same time,cerium improved wet...