The effect of hydrogen on the microstructures and superplasticity of a Ti3Al-Nb alloy was studied. The results showed that hydrogenation made the volume fraction of B2 phase increase and facilitated the dynamic recrys...The effect of hydrogen on the microstructures and superplasticity of a Ti3Al-Nb alloy was studied. The results showed that hydrogenation made the volume fraction of B2 phase increase and facilitated the dynamic recrystallization of the lath-like phase. The addition of hydrogen. reduced the flow stresses and made the maximum m value move to a lower temperature during the superplastic deformation. The superplastic deformation temperature of the alloy can be lowered by about 60 degreesC.展开更多
Study was made of the behaviour of ordering transformation in Ti_3AI-Nb alloy,including the ordering at high temperatures,the transformation of high temperature β-phase during cooling,and the decomposition of metasta...Study was made of the behaviour of ordering transformation in Ti_3AI-Nb alloy,including the ordering at high temperatures,the transformation of high temperature β-phase during cooling,and the decomposition of metastable β-phase during aging.The results show that the ordered primary α_2 and high temperature β in alloy form at 1060℃.The transformation of high temperature β-phase proceed by β→α_2+ω type during cooling,and the decomposition of metastable β and ω type proceeded by(β+ω)_(metustabte)→(α_2+β)_(stable)during aging at 700℃.展开更多
The microstructure and phase constitution in stoichiometric NbTiAl3 (γ1 phase) alloy treated at 1000℃ were examined by metallography and X-ray diffraction. The alloy microstructure is mainly γ1 phase containing η ...The microstructure and phase constitution in stoichiometric NbTiAl3 (γ1 phase) alloy treated at 1000℃ were examined by metallography and X-ray diffraction. The alloy microstructure is mainly γ1 phase containing η second phase [(Ti,Nb)Al3] less than 1%. DTA analysis shows no phase transformation from room temperature to 1200℃. In the diffusion couple of NbTiAl3 with 7-TiAl compound, clear phase boundary and composition jump exist between γ1 and γ phase.These results further confirm the existence of γ1 single phase at 1000℃ in Ti-Al-Nb ternary system.展开更多
: The effects of diffusion bonding temperature and holding time on the joint strength of Ti3Al base alloy has been investigated in this paper. The shear strength of Ti-14Al-21Nb-3Mo-V alloy diffusion bonding joint und...: The effects of diffusion bonding temperature and holding time on the joint strength of Ti3Al base alloy has been investigated in this paper. The shear strength of Ti-14Al-21Nb-3Mo-V alloy diffusion bonding joint under pressure of 12 MPa at 990℃ for 70 min was obtained to 797.6 MPa which approaches the base material strength. In addition, a short-time diffosion bonding process was studied in order to decrease the bonding cost. With the deformation of the specimens of 2.5% and the bonding temperature of 990℃ for 15 min, the bonding strength could reach 801 MPa.展开更多
The refining effect of Al3Ti1B1RE master alloy on Al sheets used for pressure can manufacture and the behavior of mixed rare earths in master alloy were investigated with XRD, OM, SEM and EDAX. It is found that the r...The refining effect of Al3Ti1B1RE master alloy on Al sheets used for pressure can manufacture and the behavior of mixed rare earths in master alloy were investigated with XRD, OM, SEM and EDAX. It is found that the refining effect of the refiner on the material has superiority over foreign or domestic Al5Ti1B refiner, and the refiner still retains its refining ability for 6 h after adding it to molten Al, thus improving the strength and plasticity of the material remarkably. The excellent refining effect and stability of AlTiBRE refiner result from that RE can lower the surface energy of molten Al and improve the wetting characteristics of molten Al on refinement nuclei such as TiAl 3, TiB 2, etc., thus giving full play to the effect of heterogeneous nucleation and impeding the congregating tendency of TiB 2 phase in molten Al. At the same time, RE gathering in front of solid/liquid interface are also easy to cause composition supercooling in molten Al, thus impeding the growth of α Al grains and promoting α Al nucleation on refinement nuclei. In addition, RE also play certain role in purification and grain refinement, or modification, especially their effect of purification can improve the metallurgical quality of AlTiBRE master alloy.展开更多
Ti3AlC2 has the properties of ceramics and metals. These excellent properties indicate that Ti3AlC2 is a very promising material to extensive applications. Ti3AlC2 ceramic material was prepared by mechanical alloying....Ti3AlC2 has the properties of ceramics and metals. These excellent properties indicate that Ti3AlC2 is a very promising material to extensive applications. Ti3AlC2 ceramic material was prepared by mechanical alloying. The effects of milling time and sintering temperature on the fracture, microstmctttre and mechanical properties of Ti3AlC2 ceramic material were analyzed by laser particle analyzer, X-ray diffraction, and scanning electron microscopy. The experimental results showed that Ti3AlC2 had the best comprehensive properties after the composite powder was milled for 3 h and sintered at 1630℃ for 2 h. The relative density, bending strength, and hardness of the sample reached 92.23%, 345.2 MPa, and HRA 34.1, respectively. The fracture surface indicated that the fracture of the material belonged to ductile rapture.展开更多
Titanium silicide Ti 5Si 3 whose melting temperature is 2 130 ℃ bears the potential for very high temperature application. Results on Nb or Cr addition to this compound with emphasis on its alloying behaviour were re...Titanium silicide Ti 5Si 3 whose melting temperature is 2 130 ℃ bears the potential for very high temperature application. Results on Nb or Cr addition to this compound with emphasis on its alloying behaviour were reported. Previous theoretical calculation shows that substitution of Ti by Nb or Cr atoms in Ti 5Si 3 crystal will enhance the bonding between atoms. By experiment, two means of alloying were considered: stoichiometric and off stoichiometric alloying. Stoichiometric alloying in Ti 5Si 3 results in compounds consisting of single Ti 5Si 3 phase while off stoichiometric alloying yields hypereutectic microstructure with Ti 5Si 3 being the primary phase. The Ti 5Si 3 phase in both cases dissolves certain amount of Nb or Cr alloying element and its composition agrees with the stoichiometric composition of (Ti,Nb) 5Si 3 or (Ti,Cr) 5Si 3. The moduli of the stoichiometric alloys increase with alloying element addition, indicating an enhancement in Ti 5Si 3 crystal.展开更多
The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion r...The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion resistance,titanium–niobium alloys have the potential to become a new generation of internal fixation materials for fractures.However,the role and mechanism of titanium–niobium alloys on promoting fracture healing are still undefined.Therefore,in this study,we systematically evaluated the bone-enabling properties of Ti45Nb via in vivo and in vitro experiments.In vitro,we found that Ti45Nb has an excellent ability to promote MC3T3-E1 cell adhesion and proliferation without obvious cytotoxicity.Alkaline phosphatase(ALP)activity and alizarin red staining and semiquantitative analysis showed that Ti45Nb enhanced the osteogenic differentiation of MC3T3-E1 cells compared to the Ti6Al4V control.In the polymerase chain reaction experiment,the expression of osteogenic genes in the Ti45Nb group,such as ALP,osteopontin(OPN),osteocalcin(OCN),type 1 collagen(Col-1)and runt-related transcription factor-2(Runx2),was significantly higher than that in the control group.Meanwhile,in the western blot experiment,the expression of osteogenic-related proteins in the Ti45Nb group was significantly increased,and the expression of PI3K–Akt-related proteins was also higher,which indicated that Ti45Nb might promote fracture healing by activating the PI3K–Akt signaling pathway.In vivo,we found that Ti45Nb implants accelerated fracture healing compared to Ti6Al4V,and the biosafety of Ti45Nb was confirmed by histological evaluation.Furthermore,immunohistochemical staining confirmed that Ti45Nb may promote osteogenesis by upregulating the PI3K/Akt signaling pathway.Our study demonstrated that Ti45Nb exerts an excellent ability to promote fracture healing as well as enhance osteoblast differentiation by activating the PI3K/Akt signaling pathway,and its good biosafety has been confirmed,which indicates its clinical translation potential.展开更多
Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidati...Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidation rate of the alloy owing to the formation of Al2O3＋Cr2O3 mixture oxide scale on the surface of the coatings. No spallation of the coatings or oxide scales took place during the cyclic oxidation at 800℃. Ti was observed to diffuse into the coatings, the diffusion distance of which was very short, and the diffusion ability of it was proportional to the AI content in the coatings. Compared to Ti, Nb can diffuse much more easily through the whole coatings and oxide scales.展开更多
The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with differen...The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with different compositions and cooling rates were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It is found that the eutectic Ti5Si3 phases in Cu-Ti-Si alloys are rod-like with hexagonal cross section which tend to intertwine with each other to form a firm skeleton like a bird nest structure which can make the alloys keep their original shape even after etching off the Cu matrix. In addition, there is Cu in the center of many Ti5Si3 rods, resulting in a core-shell structure. With the increase of the cooling rate, Ti5Si3 distributes more uniformly, and the diameter of Ti5Si3 significantly decreases, with a minimum size of less than 100 nm, while the aspect ratio of Ti5Si3 increases.展开更多
Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy...Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.展开更多
基金The projeccgt is financially supported by the National Natural Science Foundation.Oundation.]
文摘The effect of hydrogen on the microstructures and superplasticity of a Ti3Al-Nb alloy was studied. The results showed that hydrogenation made the volume fraction of B2 phase increase and facilitated the dynamic recrystallization of the lath-like phase. The addition of hydrogen. reduced the flow stresses and made the maximum m value move to a lower temperature during the superplastic deformation. The superplastic deformation temperature of the alloy can be lowered by about 60 degreesC.
文摘Study was made of the behaviour of ordering transformation in Ti_3AI-Nb alloy,including the ordering at high temperatures,the transformation of high temperature β-phase during cooling,and the decomposition of metastable β-phase during aging.The results show that the ordered primary α_2 and high temperature β in alloy form at 1060℃.The transformation of high temperature β-phase proceed by β→α_2+ω type during cooling,and the decomposition of metastable β and ω type proceeded by(β+ω)_(metustabte)→(α_2+β)_(stable)during aging at 700℃.
文摘The microstructure and phase constitution in stoichiometric NbTiAl3 (γ1 phase) alloy treated at 1000℃ were examined by metallography and X-ray diffraction. The alloy microstructure is mainly γ1 phase containing η second phase [(Ti,Nb)Al3] less than 1%. DTA analysis shows no phase transformation from room temperature to 1200℃. In the diffusion couple of NbTiAl3 with 7-TiAl compound, clear phase boundary and composition jump exist between γ1 and γ phase.These results further confirm the existence of γ1 single phase at 1000℃ in Ti-Al-Nb ternary system.
文摘: The effects of diffusion bonding temperature and holding time on the joint strength of Ti3Al base alloy has been investigated in this paper. The shear strength of Ti-14Al-21Nb-3Mo-V alloy diffusion bonding joint under pressure of 12 MPa at 990℃ for 70 min was obtained to 797.6 MPa which approaches the base material strength. In addition, a short-time diffosion bonding process was studied in order to decrease the bonding cost. With the deformation of the specimens of 2.5% and the bonding temperature of 990℃ for 15 min, the bonding strength could reach 801 MPa.
文摘The refining effect of Al3Ti1B1RE master alloy on Al sheets used for pressure can manufacture and the behavior of mixed rare earths in master alloy were investigated with XRD, OM, SEM and EDAX. It is found that the refining effect of the refiner on the material has superiority over foreign or domestic Al5Ti1B refiner, and the refiner still retains its refining ability for 6 h after adding it to molten Al, thus improving the strength and plasticity of the material remarkably. The excellent refining effect and stability of AlTiBRE refiner result from that RE can lower the surface energy of molten Al and improve the wetting characteristics of molten Al on refinement nuclei such as TiAl 3, TiB 2, etc., thus giving full play to the effect of heterogeneous nucleation and impeding the congregating tendency of TiB 2 phase in molten Al. At the same time, RE gathering in front of solid/liquid interface are also easy to cause composition supercooling in molten Al, thus impeding the growth of α Al grains and promoting α Al nucleation on refinement nuclei. In addition, RE also play certain role in purification and grain refinement, or modification, especially their effect of purification can improve the metallurgical quality of AlTiBRE master alloy.
文摘Ti3AlC2 has the properties of ceramics and metals. These excellent properties indicate that Ti3AlC2 is a very promising material to extensive applications. Ti3AlC2 ceramic material was prepared by mechanical alloying. The effects of milling time and sintering temperature on the fracture, microstmctttre and mechanical properties of Ti3AlC2 ceramic material were analyzed by laser particle analyzer, X-ray diffraction, and scanning electron microscopy. The experimental results showed that Ti3AlC2 had the best comprehensive properties after the composite powder was milled for 3 h and sintered at 1630℃ for 2 h. The relative density, bending strength, and hardness of the sample reached 92.23%, 345.2 MPa, and HRA 34.1, respectively. The fracture surface indicated that the fracture of the material belonged to ductile rapture.
文摘Titanium silicide Ti 5Si 3 whose melting temperature is 2 130 ℃ bears the potential for very high temperature application. Results on Nb or Cr addition to this compound with emphasis on its alloying behaviour were reported. Previous theoretical calculation shows that substitution of Ti by Nb or Cr atoms in Ti 5Si 3 crystal will enhance the bonding between atoms. By experiment, two means of alloying were considered: stoichiometric and off stoichiometric alloying. Stoichiometric alloying in Ti 5Si 3 results in compounds consisting of single Ti 5Si 3 phase while off stoichiometric alloying yields hypereutectic microstructure with Ti 5Si 3 being the primary phase. The Ti 5Si 3 phase in both cases dissolves certain amount of Nb or Cr alloying element and its composition agrees with the stoichiometric composition of (Ti,Nb) 5Si 3 or (Ti,Cr) 5Si 3. The moduli of the stoichiometric alloys increase with alloying element addition, indicating an enhancement in Ti 5Si 3 crystal.
基金This work was supported by the National Natural Science Foundation of China(Nos.81972058,81902194 and 82202680)the Science and Technology Commission of Shanghai Municipality(No.22YF1422900)+3 种基金the Shanghai Municipal Key Clinical Specialty,China(No.shslczdzk06701)the National Facility for Translational Medicine(Shanghai),China(No.TMSZ-2020-207)the Shanghai Engineering Research Center of Orthopedic Innovative Instruments and Personalized Medicine Instruments and Personalized Medicine(No.19DZ2250200)the Key R&D Program of Ningxia,China(Nos.2020BCH01001 and 2021BEG02037).
文摘The key to managing fracture is to achieve stable internal fixation,and currently,biologically and mechanically appropriate internal fixation devices are urgently needed.With excellent biocompatibility and corrosion resistance,titanium–niobium alloys have the potential to become a new generation of internal fixation materials for fractures.However,the role and mechanism of titanium–niobium alloys on promoting fracture healing are still undefined.Therefore,in this study,we systematically evaluated the bone-enabling properties of Ti45Nb via in vivo and in vitro experiments.In vitro,we found that Ti45Nb has an excellent ability to promote MC3T3-E1 cell adhesion and proliferation without obvious cytotoxicity.Alkaline phosphatase(ALP)activity and alizarin red staining and semiquantitative analysis showed that Ti45Nb enhanced the osteogenic differentiation of MC3T3-E1 cells compared to the Ti6Al4V control.In the polymerase chain reaction experiment,the expression of osteogenic genes in the Ti45Nb group,such as ALP,osteopontin(OPN),osteocalcin(OCN),type 1 collagen(Col-1)and runt-related transcription factor-2(Runx2),was significantly higher than that in the control group.Meanwhile,in the western blot experiment,the expression of osteogenic-related proteins in the Ti45Nb group was significantly increased,and the expression of PI3K–Akt-related proteins was also higher,which indicated that Ti45Nb might promote fracture healing by activating the PI3K–Akt signaling pathway.In vivo,we found that Ti45Nb implants accelerated fracture healing compared to Ti6Al4V,and the biosafety of Ti45Nb was confirmed by histological evaluation.Furthermore,immunohistochemical staining confirmed that Ti45Nb may promote osteogenesis by upregulating the PI3K/Akt signaling pathway.Our study demonstrated that Ti45Nb exerts an excellent ability to promote fracture healing as well as enhance osteoblast differentiation by activating the PI3K/Akt signaling pathway,and its good biosafety has been confirmed,which indicates its clinical translation potential.
基金the National Natural Science Foundation of China under grant Nos. 50371095 , 50571106.
文摘Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidation rate of the alloy owing to the formation of Al2O3＋Cr2O3 mixture oxide scale on the surface of the coatings. No spallation of the coatings or oxide scales took place during the cyclic oxidation at 800℃. Ti was observed to diffuse into the coatings, the diffusion distance of which was very short, and the diffusion ability of it was proportional to the AI content in the coatings. Compared to Ti, Nb can diffuse much more easily through the whole coatings and oxide scales.
基金This work was financially supported by the Natural Science Foundation of Hebei Province of China(Grant No.E2019502057)the Fundamental Research Funds for the Central Universities,China(Grant No.2018MS120).
文摘The Cu-Ti-Si alloys containing in-situ formed Ti5Si3 are prepared. In order to clarify the Ti5Si3 formation processes and its microstructure characteristics, the as-cast and deeply etched Cu-Ti-Si alloys with different compositions and cooling rates were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It is found that the eutectic Ti5Si3 phases in Cu-Ti-Si alloys are rod-like with hexagonal cross section which tend to intertwine with each other to form a firm skeleton like a bird nest structure which can make the alloys keep their original shape even after etching off the Cu matrix. In addition, there is Cu in the center of many Ti5Si3 rods, resulting in a core-shell structure. With the increase of the cooling rate, Ti5Si3 distributes more uniformly, and the diameter of Ti5Si3 significantly decreases, with a minimum size of less than 100 nm, while the aspect ratio of Ti5Si3 increases.
文摘Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out.Microstructures of the joint were studied by optical microscopy(OM),scanning electron microscopy(SEM) and X-ray diffractometry(XRD).In addition,the mechanical properties of the joint were evaluated by tensile test and the microhardness was measured.These two alloys were successfully welded by adding copper transition layer into the weld.Solid solution with a certain thickness was located at the interfaces between weld and base metal in both sides.Regions inside the weld and near the stainless steel were characterized by solid solution of copper with TiFe2 intermetallics dispersedly distributed in it.While weld near titanium alloy contained Ti-Cu and Ti-Fe-Cu intermetallics layer,in which the hardness of weld came to the highest value.Brittle fracture occurred in the intermetallics layer when the joint was stretched.
