This paper systematically investigated the effect of solution and artificial aging heat treatments on the microstructural evolution and mechanical properties of TiB/Ti-6Al-4V composites in situ fabricated by selective...This paper systematically investigated the effect of solution and artificial aging heat treatments on the microstructural evolution and mechanical properties of TiB/Ti-6Al-4V composites in situ fabricated by selective laser melting.The results showed that the fully martensite microstructure with TiB clusters of the as-built samples was transformed into lamellarα+βmicrostructure with TiB strips after solution heat treatment.With increasing the temperature,theαlaths and TiB particles coarsened and theβvolume fraction increased.After aging heat treatment,βvolume fraction decreased and TiB had no obvious changes.A superior combination of the yield strength of(1146.8±28.2)MPa and even higher plasticity and ultimate compressive strength((1680.1±18.3)MPa)than the as-built ones was obtained by solution heat treatment at 1000℃+water quenching and aging at 600℃for 6 hþair cooling.展开更多
Titanium-matrix composites have important and wide applications in the transport and aerospace industries. The current research was focused on powder metallurgy processing of in-situ reinforced titanium-matrix composi...Titanium-matrix composites have important and wide applications in the transport and aerospace industries. The current research was focused on powder metallurgy processing of in-situ reinforced titanium-matrix composite with Ti B whiskers. The Ti-6Al-4V alloy and B4 C additive powders were used as raw materials. Two different consolidation techniques, namely press-and-sintering and spark plasma sintering, were selected. It was observed that in-situ Ti B whiskers were formed during sintering in both methods. The changes in size, aspect ratio and distribution of in-situ whiskers in different composite samples were monitored. The effect of spark plasma sintering temperature on the synthesis of in-situ whiskers was also investigated. Based on the microstructural observations（optical microscopy and scanning electron microscopy） and the energy dispersive spectroscopy analysis, it was concluded that increasing the spark plasma sintering temperature from 900 to 1100 °C would lead to the complete formation of in-situ Ti B whiskers and reduced porosity content.展开更多
Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to ...Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to improve the deformation characteristics.Ti-6Al-4V particles reinforced AZ31 MMCs were produced through friction stir processing(FSP)which was carried out in a traditional vertical milling machine.The microstructural features as well as the response to external tensile load were explored.A homogenous distribution of Ti-6Al-4V was achieved at every part of the stir zone.There was no chemical decomposition of Ti-6Al-4V.Further,Ti-6Al-4V did not react with Al and Zn present in AZ31 alloy to form new compounds.A continuous strong interface was obtained around Ti-6Al-4V particle with the matrix.Ti-6Al-4V particles underwent breakage during processing due to severe plastic strain.There was a remarkable refinement of grains in the composite caused by dynamic recrystallization in addition to the pinning of smaller size broken particles.Dense dislocations were observed in the matrix because of plastic deformation and the associated strain misfit.Ti-6Al-4V particles improved the tensile behavior and assisted to obtain appreciable deformation before fracture.Brittle mode of failure was avoided.展开更多
This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The ...This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The findings revealed the formation ofγ-TiH andδ-TiH_(2) hydrides in the alloy after hydrogen charging.Prolonging hydrogen charging resulted in more significant degradation of the alloy microstructure,leading to deteriorated protectiveness of the surface film.This trend was further confirmed by the electrochemical measurements,which showed that the corrosion resistance of the alloy progressively worsened as the hydrogen charging time was increased.Consequently,this work provides valuable insights into the mechanisms underlying the corrosion of Ti-6Al-4V alloy under hydrogen charging conditions.展开更多
SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influ...SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influence of heat exposure time on products of thelinterfacial reaction was investigated using scanning electron microscope （SEM） and analytical transmission electron microscope （TEM） with energy dispersive spectrometer （EDS）. The main products are TiC and Ti5Si3 after vacuum exposing the samples at 700℃ for 50 h. The growth dynamics of interracial reaction products was analyzed quantitatively, which fitted the parabola rule. The activity energy of the reaction was 252 kJ·mol^-1.展开更多
基金sponsored by the National Natural Science Foundation of China(Grant No.51775208,51922044)the Hubei Science Fund for Distinguished Young Scholars(No.0216110085)+1 种基金Wuhan Plan of Science and Technology(No.2018010401011281)the Academic Frontier Youth Team(2018QYTD04)at Huazhong University of Science and Technology(HUST).
文摘This paper systematically investigated the effect of solution and artificial aging heat treatments on the microstructural evolution and mechanical properties of TiB/Ti-6Al-4V composites in situ fabricated by selective laser melting.The results showed that the fully martensite microstructure with TiB clusters of the as-built samples was transformed into lamellarα+βmicrostructure with TiB strips after solution heat treatment.With increasing the temperature,theαlaths and TiB particles coarsened and theβvolume fraction increased.After aging heat treatment,βvolume fraction decreased and TiB had no obvious changes.A superior combination of the yield strength of(1146.8±28.2)MPa and even higher plasticity and ultimate compressive strength((1680.1±18.3)MPa)than the as-built ones was obtained by solution heat treatment at 1000℃+water quenching and aging at 600℃for 6 hþair cooling.
文摘Titanium-matrix composites have important and wide applications in the transport and aerospace industries. The current research was focused on powder metallurgy processing of in-situ reinforced titanium-matrix composite with Ti B whiskers. The Ti-6Al-4V alloy and B4 C additive powders were used as raw materials. Two different consolidation techniques, namely press-and-sintering and spark plasma sintering, were selected. It was observed that in-situ Ti B whiskers were formed during sintering in both methods. The changes in size, aspect ratio and distribution of in-situ whiskers in different composite samples were monitored. The effect of spark plasma sintering temperature on the synthesis of in-situ whiskers was also investigated. Based on the microstructural observations（optical microscopy and scanning electron microscopy） and the energy dispersive spectroscopy analysis, it was concluded that increasing the spark plasma sintering temperature from 900 to 1100 °C would lead to the complete formation of in-situ Ti B whiskers and reduced porosity content.
文摘Poor ductility is the primary concern of magnesium matrix composites(MMCs)inflicted by non-deformable ceramic particle reinforcements.Metal particles which melt at elevated temperature can be used as reinforcement to improve the deformation characteristics.Ti-6Al-4V particles reinforced AZ31 MMCs were produced through friction stir processing(FSP)which was carried out in a traditional vertical milling machine.The microstructural features as well as the response to external tensile load were explored.A homogenous distribution of Ti-6Al-4V was achieved at every part of the stir zone.There was no chemical decomposition of Ti-6Al-4V.Further,Ti-6Al-4V did not react with Al and Zn present in AZ31 alloy to form new compounds.A continuous strong interface was obtained around Ti-6Al-4V particle with the matrix.Ti-6Al-4V particles underwent breakage during processing due to severe plastic strain.There was a remarkable refinement of grains in the composite caused by dynamic recrystallization in addition to the pinning of smaller size broken particles.Dense dislocations were observed in the matrix because of plastic deformation and the associated strain misfit.Ti-6Al-4V particles improved the tensile behavior and assisted to obtain appreciable deformation before fracture.Brittle mode of failure was avoided.
基金Supported by National Natural Science Foundation of China(Grant Nos.52001142,52005228,51801218,51911530211,51905110)Young Scientists Sponsorship Program by CAST(Grant No.2022QNRC001).
文摘This study employs advanced electrochemical and surface characterization techniques to investigate the impact of electrochemical hydrogen charging on the corrosion behavior and surface film of the Ti-6Al-4V alloy.The findings revealed the formation ofγ-TiH andδ-TiH_(2) hydrides in the alloy after hydrogen charging.Prolonging hydrogen charging resulted in more significant degradation of the alloy microstructure,leading to deteriorated protectiveness of the surface film.This trend was further confirmed by the electrochemical measurements,which showed that the corrosion resistance of the alloy progressively worsened as the hydrogen charging time was increased.Consequently,this work provides valuable insights into the mechanisms underlying the corrosion of Ti-6Al-4V alloy under hydrogen charging conditions.
文摘SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influence of heat exposure time on products of thelinterfacial reaction was investigated using scanning electron microscope （SEM） and analytical transmission electron microscope （TEM） with energy dispersive spectrometer （EDS）. The main products are TiC and Ti5Si3 after vacuum exposing the samples at 700℃ for 50 h. The growth dynamics of interracial reaction products was analyzed quantitatively, which fitted the parabola rule. The activity energy of the reaction was 252 kJ·mol^-1.
