Microstructure evolution and nitrides precipitation in in-situ Ti_2 AlN/TiAl composites during isothermal aging at 900°C

Microstructures of Ti2AlN/TiAl composites prepared by in-situ method were characterized in in-situ and aging treatment conditions and the nitride precipitation was investigated in Ti2AlN/TiAl composites aged at 900 ℃ for 24 h after being heat treated at 1400 ℃ for 0.5 h. The in-situ composites consist of γ＋α2 lamellar colonies, equiaxed y grains and Ti2AlN reinforcements. Matrix with nearly fully lamellar structure formed after solution and subsequently aging treatment. With the increase of Ti2AlN content, the nearly fully lamellar structure becomes instable for the aged composites. According to TEM study, fine Ti2AlN precipitates are found to distribute at the grain boundaries of lamellar colony. Needle-like Ti3AlN precipitates arrange in line with growing axis parallel to [001] direction of the γ-TiAl matrix and another needle-like Ti3AlN precipitates with lager size distribute at the dislocations. Key words：

旋转超声加工对TiBw网状钛基复合材料表面残余应力的影响

为研究不同切削条件下旋转超声加工对材料表面残余应力的影响,选取硼化钛晶须(TiB whiskers,TiBw)网状钛基复合材料为实验对象,使用镍基电铸金刚石砂轮进行旋转超声加工,并分析了加工后材料的表面残余应力。结果表明:由于钛基复合材料具有网状结构和优异的高温性能,使切削热和微观相变产生的残余应力较小,磨粒机械作用产生的残余应力更大。随着超声振动的引入,磨粒高频冲击工件表面,使旋转超声加工工件表面残余应力均大于普通磨削。在主轴转速n=9000 r/min,进给速度v f=8 mm/min,加工深度a p=25μm的加工参数下,旋转超声加工工件表面存在-540 MPa的残余压应力,随着主轴转速增大,残余应力显著减小,并且残余应力的影响层深度逐渐减小。超声振动的引入增大工件表面残余压应力,提高材料抗疲劳性能。

Microstructures and mechanical properties of titanium-reinforced magnesium matrix composites: Review and perspective

Currently, many gratifying signs of progress have been made in magnesium(Mg) matrix composites(MMCs) by virtue of their high mechanical properties both at room and elevated temperatures. Although the commonly used reinforcements in MMCs are ceramic particles,they often provide improved yield and ultimate stresses by a significant loss in ductility. Therefore, hard metallic phases were introduced as alternative candidates for the manufacturing of MMCs, especially titanium(Ti). It has a high melting point, high Young’s modulus, high plasticity, low level of mutual solubility with Mg matrix, and closer thermal expansion coefficient to that of Mg metal than that of ceramic particles. It is highly preferable to provide both high ultimate stress and ductility in Mg matrix. However, many critical challenges for the fabrication of Ti-reinforced MMCs remain, such as Ti’s homogeneity, low recovery rate, and the optimization of interfacial bonding strength between Mg and Ti, etc. Meanwhile, different fabrication methods have various effects on the microstructures, mechanical properties, and the interfacial strength of Ti-reinforced MMCs. Hence, this review placed emphasis on the microstructural characteristics and mechanical properties of Ti-reinforced MMCs fabricated by different techniques. The influencing factors that govern the strengthening mechanisms were systematically compared and discussed. Future research trends, key issues, and prospects were also proposed to develop Ti-reinforced MMCs.

Preparation of Al-Al_3Ti in situ composites by direct reaction method

Al-Al3Ti composites were prepared by a direct reaction method, in which Al3Ti was formed by the reaction of Ti and Al in aluminum alloy melt. The morphology of Al3Ti changes apparently from the fine particle, needle-like to large block with the increase of Al3Ti content. The addition of magnesium can markedly change the morphology of Al3Ti and reduce their size. Short rod-like Al3Ti was formed and homogeneous distribution was obtained with the addition of 3 wt.% Mg. The effect of Al3Ti and Mg on the microstructure of Al-Al3Ti composites and the mechanism were also discussed.

Microstructure,hardness and corrosion properties of laser processed Ti6Al4V-based composites

Nb and Ti-13 Nb powders were used for improving the surface of Ti6Al4 V alloy.The deposition of the powders was carried out at various laser powers.The scanning electron microscopy（SEM）-EDS and optical microscopy were used for characterization.X-ray diffractometer（XRD） was used for analyzing the elemental composition and phase constituents.The hardness,wear and corrosion properties were achieved.The corrosion and the wear behaviours of the deposited layers were studied in a Hanks solution（simulated body fluid,SBF）.The microstructures of Nb coatings reveal the presence of orthorhombic,dendritic α″ and metastable β-Nb phases which produce uneven hardness with an average of HV 364.For Ti-13 Nb coatings,martensitic α′ and metastable β-Nb phases with an average hardness of HV 423 were observed.The resistance of wear on dry sliding of Ti-13 Nb coating is attributed to the increase in hardness.Experimental results indicate that deposition of Nb and Ti-13 Nb on Ti6Al4 V grossly reduces the mass fractions of Al and V in all coatings.In SBF,Nb reinforcement produces the best coating that reveals the best wear and corrosion resistances as compared with the substrate.Hence,this coating will perform best for orthopaedic implant material enhancement.

Formation mechanism and growth kinetics of TiAl_(3) phase in cold-rolled Ti/Al laminated composites during annealing

Cold-rolled Ti/Al laminated composites were annealed at 525−625℃for 0−128 h,and the interfacial microstructure evolution was investigated.The results indicate that only the TiAl_(3) phase was formed at the Ti/Al interface;most of TiAl_(3) grains were fine equiaxed with average sizes ranging from hundreds of nanometers to several microns and the TiAl_(3) grain size increased with increasing annealing time and/or temperature,but the effect of annealing temperature on the TiAl_(3) grain size was far greater than that of annealing time.The growth of the TiAl_(3) phase consisted of two stages.The initial stage was governed by chemical reaction with a reaction activation energy of 195.75 kJ/mol,and the reaction rate constant of the TiAl_(3) phase was larger as the Ti/Al interface was bonded with fresh surfaces.At the second stage,the growth was governed by diffusion,the diffusion activation energy was 33.69 kJ/mol,and the diffusion growth rate constant of the TiAl_(3) phase was mainly determined by the grain boundary diffusion owing to the smaller TiAl_(3) grain size.

Microstructure,mechanical properties and wear resistance of Ti particles reinforced AZ31 magnesium matrix composites

The compromise between strength and plasticity has greatly limited the potential application of particles reinforced magnesium matrix composites(MMCs).In this work,the Ti particles reinforced AZ31 magnesium(Mg)matrix composites achieved simultaneous improvement in strength,elongation and wear resistance.The Ti particles reinforced AZ31 composites were fabricated by ultrasonic-assisted stir casting with hot extrusion.The results showed that a strong interfacial bonding was obtained at Ti/Mg interface because of the formation of semicoherent orientation relationship of Ti Al/Mg,Ti Al/Al_(2)Ti and Al_(2)Ti/Mg interfaces.The as-extruded 6 wt.%Ti/AZ31 composite presented the best compressive mechanical properties and wear resistance with ultimate tensile strength,elongation and wear rate of 327 MPa,20.4%and 9.026×10^(-3)mm^(3)/m,obviously higher than those of AZ31 alloys.The enhanced mechanical properties were attributed to the grain refinement and strong interfacial bonding.The improved wear resistance was closely related to the increased hardness of composites and the formation of protective oxidation films.

Rheological behavior of semi-solid TiB_2/7075 composites and simulation of their rheocasting processes

In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The effects of the addition of 4.5wt.% and 9wt.%Ti B2 on the apparent viscosity and microstructure were investigated. The results showed that adding Ti B2 is effective for optimizing primary α-Al, but compared with the 4.5wt.%Ti B2/7075 composite, the addition of 9wt.%Ti B2 had no further significant refinement role in the 9wt.%Ti B2/7075 composite due to particle aggregation. The viscosities of semi-solid 7075 alloy and Ti B2/7075 composite slurries increased with an increase in solid fraction, but decreased with an increase in shear rate. The viscosity of 4.5wt.% Ti B2/7075 was the lowest among the three samples, and that of 7075 alloy was the highest under the same conditions. The primary α-Al grain size was decreased, and the dendritic grains grew into spherical shapes after shearing. Based on the experimental results, viscosity models of the semi-solid 7075 alloy and 4.5wt.% and 9wt.%Ti B2/7075 composites were formulated. According to the simulation results, the shrinkage porosity of the 4.5wt.%Ti B2/7075 wheel was lower than those of the 7075 alloy and 9wt.%Ti B2/7075 wheels.

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Ti/Cu/Ti laminated composites were fabricated by corrugated rolling(CR) and flat rolling(FR) method.Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.

Effect of Ti/B Additions on the Formation of Al_3 Ti of in situ TiB_2/Al Composites

A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.

Friction and Wear Properties of TiAl and Ti_2AlN/TiAl Composites at High Temperature

The high-temperature friction and wear properties of TiAl alloys and Ti2AlN/TiAl composites （TTC） in contact with nickel-based superalloy were studied. The results showed that, at 800 and 1 000 ℃, the coefficient of the friction （COF） decreased with the increase of sliding velocity and the wear loss of the TTC decreased with the increase of volume fraction of Ti2AlN. The wear mechanisms of the pairs are adhesive wear and the wear debris mainly comes from the contacting nickel-based superalloy. The intergranular fracture and the cracking of the phase boundary in the lamellar structure are the wear mode of TiAl alloy. The wear mode of TTC is phase boundary fracture and adhesive spalling. The abrasive resistance of TTC is slightly higher than that of TiAl alloy.

Physical, Antioxidant and Thermal Shock Properties of Cu/Ti_2AlC Conductive Composites

Cu/Ti2AlC composites were fabricated by vacuum hot-pressing technique. Phase composition was analyzed by XRD and morphology of fracture was observed by SEM. Physical performance such as density, resistivity, hardness and friction coefficient with different volume fraction of Cu/Ti2AlC composites were studied. When the content of Ti2AlC increased from 10% to 70%, the relative density reduced from 99.38% to 90.56% and the resistivity increased significantly. Hardness reached the maximum value when Ti2AlC was at 60% and friction coefficient declined with the increasing of Ti2AlC. Cu/Ti2AlC composites, showing good conductivity properties and friction performance. Oxidation resistance enhanced obviously with the content of Ti2AlC increasing. Cu-60%Ti2AlC sample possessed optimum thermal shock resistance, and no cracking was found at 600 ℃ cycled for 10 times and 900 ℃ cycled for 1 time.

Decorating MXene with tiny ZIF-8 nanoparticles:An effective approach to construct composites for water pollutant removal

MXenes have attracted increasing research enthusiasm owing to their unique physical and chemical properties.Although MXenes exhibit exciting potential in cations adsorption due to their unique surface groups,the adsorption capacity is limited by the low specific surface area and undeveloped porosity.Our work aims at enhancing the adsorption performance of a well-known MXene,Ti3C2Tx,for methylene blue(MB)by decorating tiny ZIF-8 nanoparticles in the interlayer.After the incorporation of ZIF-8,suitable interspace in the layers resulting from the distribution of tiny ZIF-8 appears.When employing in MB,the adsorption capacity of composites can reach up to 107 mg·g^(-1) while both ZIF-8(3 mg·g^(-1))and Ti_(3)C_(2)Tx(9mg·g^(-1))show nearly no adsorption capacity.The adsorption mechanism was explored,and the good adsorption capacity is caused by the synergistic effect of ZIF-8 and Ti_(3)C_(2)Tx,for neither of them is of suitable interspace or surface groups for MB adsorption.Our work might pave the way for constructing functional materials based on the introduction of nanoparticles into layered materials for various adsorption applications.

IN SITU PROCESSING OF Al_(2)O_(3) WHISKERS REINFORCED Ti-Al INTERMETALLIC COMPOSITES

In situ Al2O3 whiskers reinforced Ti-Al intermetallic composites were fabricated at ~1200℃ by reaction sintering of cold-consolidated fillets consisting mainly of Ti, Al, and different additives. The phases and microstructures of the sintered composites were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS). The process of synthesis was investigated using differential thermal analysis (DTA). The effects of processing parameters and additives on the microstructures of the composites and the development of whisker were examined. It is found that the morphology of the whisker is strongly influenced by the additives, the exothermal reaction process, and the processing parameters.

Microstructure Characteristic of In-situ Ti/TiC Composites

TiC reinforced titanium composites has been produced with different Al content and C content by XDTM. The results have shown that TiC particles are of two different morphologies f coarse dendritical primary TiC and short bar-shape eutectic TiC. Al content has great effects on the morphology of TiC. With the increasing of Al content, the morphology of primary TiC changes from coarse developed dendrite into short bar-shape or plate--shape TiC with 35%Al. Meanwhile, the structure of the matrix changes from single Ti to Ti and Ti3Al, and to Ti3Al and TiAl. However, the C content has no influence on the microstructure of matrix. When the C content is less than 1.2%, the dendrite TiC disappears and only short bar-shape or plate-shape TiC exists in the composites. In addition, the effect of he3t treatment on the morphology of TiC has also Studied.

Processing and characteristics of TiB_2 toughened B-Ti-C composites

B Ti C composites toughened by TiB 2 particles were produced by reaction sintering of B 4C, TiC and TiB 2 powders. Microstructure and mechanical properties of the composites were studied. A notable improvement on flexure strength and fracture toughness were achieved in B 4C composites containing 10%TiB 2 and 20%30%TiC(volume fraction). The highest flexure strength and fracture toughness, 425 MPa and 8.2 MPa·m 1/2 , respectively, resulted for B 4C 10%TiB 2 30%TiC composite, are much higher than those for monolithic B 4C. The main toughening mechanism is microcrack toughening and crack deflection toughening.

Effect of carbon content on microstructure and property of TiC/Ti-6Al-4V composites

TiC reinforced Ti-6Al-4V matrix composites were fabricated by consumable arc-melting technology utilizing the reaction between titanium and graphite. The phase composition,microstructure and hardness of the TiC/Ti-6Al-4V composites were investigated by XRD,SEM and hardness testing equipment,respectively. The results show that the reinforcements are distributed uniformly in the matrix alloy. With the carbon content of the composites increasing from 0.15% to2.0%,the morphology of TiC transforms from particle into short-bar shape or chain-type consisting of featheriness or wheat-shape and finally into dendritic. Simultaneously,the hardness of the composites increases. The formation mechanisms of TiC can be analyzed as follows:the growth of dendritic primary TiC before the peritectic reaction is dominated by the solute concentration gradient,after peritectic reaction,the nucleation and growth of TiC in β-Ti leads to its forming of short-bar shape. The dendritic TiC mainly is distributed in the matrix grain,but the short-bar shape TiC mainly segregates at the grain boundary,especially at the triangular grain boundaries.

Compositing Soft Coated Ti-Fiber Reinforced Ti-Al Matrix Composites

It is showed that there are Ti 3Al, Ti 2Cu and β phase in the interface of Ti/Ti Al composites reinforced with Y 2O 3 Cr composite soft coated Ti fiber, and that interface bonding is intact. Bending strength of the composites can be increased by 26%, to 709 MPa, and bending deflection increased slightly compared with the Ti/Ti Al composites reinforced by Ti fibers coated with Y 2O 3.

Preparation and Interfacial Stability of SiC_f/Ti-6Al-4V Composites Fabricated Using Powder Coated Fiber Method

SiCf/Ti-6Al-4V composites were fabricated by the powder-coated fiber method. The precursor fiber was prepared under the optimized parameter, and the composites were made using the vacuum hot pressure method. The influence of heat exposure time on products of thelinterfacial reaction was investigated using scanning electron microscope （SEM） and analytical transmission electron microscope （TEM） with energy dispersive spectrometer （EDS）. The main products are TiC and Ti5Si3 after vacuum exposing the samples at 700℃ for 50 h. The growth dynamics of interracial reaction products was analyzed quantitatively, which fitted the parabola rule. The activity energy of the reaction was 252 kJ·mol^-1.

Preparation of TiAl/Ti_2AlC Composites with Ti/Al/C Powders by In-situ Hot Pressing

TiAl/Ti2AlC composites were prepared by in-situ hot pressing of TilAl/C powders mixtures and sintered at different temperatures were investigated by X- ray diffraction （ XRD ） of samples. The reaction procedure of Ti-Al-C system could be divided into three stnges. Below 900℃ , Ti reacts with Al to form TiAl intermetallics ; above 900 ℃ , C reacts with remain Ti to form TiC triggered by the exothermal reaction of Ti and Al ; TiAl reacts with TiC to produce dense TiAl/Ti2AlC compasites.In the holding stage, ternary Ti2AlC develops to layered polycrystal and composites pyknosis in the meanwhile. The mechanism of synthesis and microstructure was especially discussed.