Microstructure and mechanical properties of TiN/TiAlN multilayer coatings deposited by arc ion plating with separate targets

TiN/TiAlN multilayer coatings were prepared by arc ion plating with separate targets. In order to decrease the unfavorable macroparticles, a straight magnetized filter was used for the low melting aluminium target. The results show that the output plasmas of titanium target without filter and aluminium target with filter reach the substrate with the same order of magnitude. Meanwhile, the number of macropartieles in TiN/TiAlN multilayer coatings deposited with separate targets is only 1/10-1/3 of that deposited with alloy target reported in literature. Al atom addition may lead to the decrease of peak at （200） lattice plane and strengthening of peak at （111） and （220） lattice planes. The measured hardness of TiN/TiAlN multilayer coatings accords with the mixture principle and the maximum hardness is HV2495. The adhesion strength reaches 75 N.

Effect of N_(2) partial pressure on comprehensive properties of antibacterial TiN/Cu nanocomposite coating

Foreign body reactions to the wear debris and corrosion products from the implants,and bacterial infections are the main factors leading to the implant failures.In order to resolve these problems,the antibacterial TiN/Cu nanocomposite coatings with various N_(2) partial pressures were deposited on 304 stainless steels(SS)using an arc ion plating(AIP)system,named TiN/Cu-x(x=0.5,1.0,1.5 Pa).The results of X-ray diffraction analysis,energy-dispersive X-ray spectroscopy,and scanning electron microscopy showed that the N_(2) partial pressures determined the Cu contents,surface defects,and crystallite sizes of TiN/Cu nanocomposite coatings,which further influenced the comprehensive abilities.And the hardness and wear resistances of TiN/Cu coatings were enhanced with increase of the crystallite sizes.Under the co-actions of surface defects,crystallite sizes,and Cu content,TiN/Cu-1.0 and TiN/Cu-1.5 coatings possessed excellent corrosion resistance.Besides,the biological tests proved that all the TiN/Cu coatings showed no cytotoxicity with strong antibacterial ability.Among them,TiN/Cu-1.5 coating significantly promoted the cell proliferation,which is expected to be a novel antibacterial,corrosion-resistant,and wear-resistant coating on the surfaces of medical implants.

Structure and wear resistance of TiN and TiAlN coatings on AZ91 alloy deposited by multi-arc ion plating

In order to investigate the microstructure of TiN and TiAlN coatings and their effect on the wear resistance of Mg alloy, TiN and TiAlN coatings were deposited on AZ91 magnesium alloy by multi-arc ion plating technology.TiN and Ti70Al30N coatings were prepared on the substrate,respectively,which exhibited dark golden color and compact microstructure.The microstructures of TiN and Ti70Al30N coatings were investigated by X-ray diffractometry(XRD)and scanning electron microscopy(SEM).The micro-hardness and wear resistance of TiN and Ti70Al30N coatings were investigated in comparison with the uncoated AZ91 alloy. The XRD peaks assigned to TiN and TiAlN phases are found.The hardness of TiN coatings is two times as high as that of AZ91 alloy, and Ti70Al30N coating exhibits the highest hardness.The wear resistance of the hard coatings increases obviously as result of their high hardness.

AFM Analysis of TiN, TiAlN, and TiAlSiN Coatings Prepared by Cathodic Arc Ion Plating

The TiN, TiAlN, and TiAlSiN coatings were prepared on YT14 cutting tool surface with CAIP（cathode arc ion plating）, the surface morphologies and phases were analyzed with FESEM（field emission scanning electron microscopy）, and XRD（X-ray diffraction）, respectively, and the coating parameters such as 3D surface micro-topography, grain size, surface height, hierarchy, profile height, and power spectral density, etc, were measured with AFM（atomic force microscope）. The results show that the phases of TiN, TiAlN, and TiAlSiN coatings are TiN, TiN＋TiAlN, TiN＋Si_3N_4＋TiAlN, respectively, while the surface roughness Sa of TiN, TiAlN, and TiAlSiN coatings is 75.3, 98.9, and 42.1 nm, respectively, and the roughness depth Sk is 209, 389, and 54 nm, respectively, the sequence of average grain sizes is TiAlN〉TiN〉TiAlSiN. The surface bearing index Sbi of TiN, TiAlN, and TiAlSiN coatings is 0.884, 1.01, and 0.37, respectively, and the sequence of surface bearing capability is TiAlN〉TiN〉TiAlSiN. At the lower wavelength（102-103 nm）, the power spectral densities have a certain correlation, and the sequence of TiN〉TiAlN〉TiAlSiN, while the correlation is low at the higher wavelength（〉103 nm）.

Effects of nitrogen flux on microstructure and tribological properties of in-situ TiN coatings deposited on TC11 titanium alloy by electrospark deposition

In order to improve the tribological properties of titanium alloys,the in-situ TiN coatings were prepared by electrospark deposition（ESD） on the surface of TC11 titanium alloy.The effects of nitrogen flux on the microstructure and tribological properties of TiN coatings were investigated.The results show that the coating is relative thin when the nitrogen flux is small and mainly consists of Ti2N,α-Ti,Ti O and TiN phases,and the metastable phase of Ti2N is developed due to the rapid solidification of ESD.While in excessive nitrogen flux condition,many micro-cracks and holes might be generated in the coating.In moderate nitrogen flux,the coating is mainly composed of TiN phase,and is dense and uniform（50-55 μm）.The average hardness is HV0.2 1165.2,which is 3.4 times that of the TC11 substrate.The TiN coatings prepared in moderate nitrogen flux perform the best wear resistance.The wear loss of the coating is 0.4 mg,which is 2/9 that of the TC11 substrate.The main wear mechanisms of the coatings are micro-cutting wear accompanied by multi-plastic deformation wear.

Effects of surface roughness of substrate on properties of Ti/TiN/Zr/ZrN multilayer coatings

Ti/TiN/Zr/ZrN multilayer coatings were deposited on Cr_17Ni_2 steel substrates with different surface roughnesses by vacuum cathodic arc deposition method. Microstructure, micro-hardness, adhesion strength and cross-sectional morphology of the obtained multilayer coatings were investigated. The results show that the Vickers hardness of Ti/TiN/Zr/ZrN multilayer coating, with a film thickness of 11.37 μm, is 29.36 GPa. The erosion and salt spray resistance performance of Cr_17Ni_2 steel substrates can be evidently improved by Ti/TiN/Zr/ZrN multilayer coating. The surface roughness of Cr_17Ni_2 steel substrates plays an important role in determining the mechanical and erosion performances of Ti/TiN/Zr/ZrN multilayer coatings. Overall, a low value of the surface roughness of substrates corresponds to an improved performance of erosion and salt spray resistance of multilayer coatings. The optimized performance of Ti/TiN/Zr/ZrN multilayer coatings can be achieved provided that the surface roughness of Cr_17Ni_2 steel substrates is lower than 0.4μm.

Electrodeposition and corrosion resistance of Ni-P-TiN composite coating on AZ91D magnesium alloy

In order to improve the corrosion resistance and microhardness of AZ91D magnesium alloy, TiN nanoparticles were addedto fabricate Ni-P-TiN composite coating by electrodeposition. The surface, cross-section morphology and composition wereexamined using SEM, EDS and XRD, and the corrosion resistance was checked by electrochemical technology. The results indicatethat TiN nanoparticles were doped successfully in the Ni-P matrix after a series of complex pretreatments including activation, zincimmersion and pre-electroplating, which enhances the stability of magnesium alloy in electrolyte and the adhesion betweenmagnesium alloy and composite coating. The microhardness of the Ni-P coating increases dramatically by adding TiN nanoparticlesand subsequent heat treatment. The corrosion experimental results indicate that the corrosion resistance of Ni-P-TiN compositecoating is much higher than that of uncoated AZ91D magnesium alloy and similar with Ni-P coating in short immersion time.However, TiN nanoparticles play a significant role in long-term corrosion resistance of composite coatings.

TiN_(0.3)/AlN复合烧结界面扩散现象

为研究TiN_(0.3)/AlN复合烧结体中两相界面区域的N原子的扩散现象,通过机械合金化方法制备出非化学计量比TiN_(0.3),采用放电等离子体烧结技术分层及复合烧结TiN_(0.3)/AlN复合材料,采用金相、XRD、SEM、EDS及TEM等分析表征TiN_(0.3)/AlN复合材料的物相组成、元素分布和组织形貌。结果表明:AlN中的N通过空位扩散机制向TiN_(0.3)中扩散,其扩散程度逐渐减弱;与AlN接触的TiN_(0.3)部分由于吸收了来自AlN中的N使成分接近正常比例的TiN,而远离界面处的部分则接近TiN_(0.3)的成分;在两相结合区域有宽度在1 nm以下的非晶层,其电子衍射斑点出现纵向伸长,产生共格,说明六方结构的AlN晶格向TiN晶格畸变,形成面心立方结构的TiN_(0.3)/AlN。

TC4表面TiN/Ti涂层的热腐蚀行为研究及第一性原理计算

目的综合评估涂层性能、延长压气机叶片的使用寿命,进行TiN/Ti涂层及冲蚀后TiN/Ti涂层的热腐蚀行为机制研究。方法进行了完整TiN/Ti涂层及冲蚀后TiN/Ti涂层300℃/120h的热腐蚀实验,腐蚀介质为95%(质量分数)Na_(2)SO_(4)+5%(质量分数)NaCl。冲蚀实验采用形状不规则的SiO_(2)颗粒,冲蚀角为45°,冲蚀速度为130 m/s,供砂速率为6.4 g/min。建立了完整TiN涂层、表面具有孔洞的TiN涂层及表面具有Ti液滴的TiN涂层3种第一性原理腐蚀计算模型。结果TiN/Ti涂层热腐蚀后,液滴处发生氧化并且变得疏松;样品切割边缘产生腐蚀锈迹,最终出现鼓包和裂纹;冲蚀后,涂层表面的完整性受到破坏,相较于未冲蚀区域,冲蚀坑周围更容易出现腐蚀。在热腐蚀过程中,SO_(4)^(2-)中的O和完整TiN涂层中的Ti以及液滴中的Ti电子云团接触,存在电荷转移及成键倾向,具体为Ti失电子、O得电子,腐蚀主要发生在SO_(4)^(2-)中的O与Ti之间。结论第一性原理计算结果与热腐蚀的实验结果相一致,第一性原理计算结果可以从微观上反映液滴和孔洞等缺陷对涂层热腐蚀行为的影响,能够为分析涂层的热腐蚀机制提供理论依据。

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makes a contribution to form the preferred direction along with a (111) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.

基于机械干态颗粒涂层技术制备cBN@TiN粉体

采用机械干态颗粒涂层技术分别制备了cBN@TiO_(2)(TiO_(2)包覆立方氮化硼)粉体和cBN@(TiO_(2)+C)(TiO_(2)+碳包覆立方氮化硼)粉体,然后在1600℃、N_(2)气氛下进行高温热处理制备cBN@TiN(TiN包覆立方氮化硼)粉体,研究了高温热处理前后粉体的物相组成与微观形貌以及高温反应机理。结果表明:机械干态颗粒涂层技术可以使纳米TiO_(2)和纳米TiO_(2)+C颗粒均匀包裹在cBN颗粒表面。在高温热处理过程中,TiO_(2)与cBN反应生成液相B_(2)O_(3),促进了cBN相变成六方氮化硼(hBN),cBN的高温稳定性差,以cBN@TiO_(2)为原料制备的cBN@TiN粉体颗粒表面形成由TiN相和hBN相组成的片状结构层;当存在碳时,TiO_(2)会优先与碳发生还原反应生成TiN,抑制B_(2)O_(3)的生成,从而降低cBN相变量,此时cBN的高温稳定性好,以cBN@(TiO_(2)+C)为原料制备的cBN@TiN粉体颗粒表面形成主要为TiN相的颗粒结构层。

Effect of Al and Si additions on microstructure and mechanical properties of TiN coatings

Ti-X-N (X=Al,Si or Al+Si) coatings were grown onto cemented carbide substrates by cathodic arc evaporation. The hardness of the coatings was obtained by nanoindentation and the microstructure was investigated by XRD,XPS and SEM. Solid solution hardening results in a hardness increase from 24 GPa for TiN to 31.2 GPa for TiAlN. The higher hardness values of 36.7 GPa for TiSiN and 42.4 GPa for TiAlSiN are obtained by the incorporation of Si into TiN (TiAlN) coatings due to the formation of special three-dimensional net structure consisting of nanocrystalline (nc) TiN (TiAlN) encapsulated in an amorphous (a) Si3N4 matrix phase. Furthermore,the nc-TiAlN/a-Si3N4 coating shows the best machining performance.

Microstructure and tribocorrosion performance of nanocrystalline TiN graded coating on biomedical titanium alloy

A nanocrystalline TiN graded coating was prepared on Ti6Al4V alloy by DC reactive magnetron sputtering method. The microstructure and mechanic properties of the coating were investigated. The electrochemical corrosion and tribocorrosion of the coated specimens in physiological environment were compared with those of Ti6Al4V substrate. The results show that the gradient distribution of nanocrystalline TiN is favorable for releasing the inner stress in the coating, which increases adhesion strength to 90 N. The compact structure and refined-grains of the coating result in the surface nanohardness of 28.5 GPa. The corrosion protection efficiency of the nanocrystalline TiN coating reaches 96.6%. The tribocorrosion resistance of the coating increases by 100 times in comparison with that of Ti6Al4V substrate. The high chemical stability and H3/E2 ratio (where H is hardness, and E is elastic modulus) of the nanocrystalline TiN coating are responsible for good corrosion and wear resistances.

Effects of process parameters on microstructure and wear resistance of TiN coatings deposited on TC11 titanium alloy by electrospark deposition

In the present study,the effects of process parameters(output voltage x,nitrogen flux l and specific strengthening time s)on the microstructure and wear resistance properties of TiN coatings prepared by electrospark deposition(ESD)were investigatedsystematically.The microstructure of the coatings was characterized for thickness(TOC),content of TiN(CON)and porosity(POC).A statistical model was developed to identify the significant factors affecting the microstructure and wear resistance of the coatings.The results show that the output voltage x and nitrogen flux l present significant effects on majority of the evaluation indexes such asTOC,friction coefficient(COF)and wear mass loss(Id),while the specific strengthening time s has a significant effect on POC and asmall effect on the other indexes.The optimal process parameters were obtained as follows:output voltage(x,60V),nitrogen flux(l,15L/min)and specific strengthening time(s,3min/cm2).The variation of wear mass loss(Id)by the variation of the outputvoltage(x)and nitrogen flux(l)is attributed to the change of wear mechanisms of TiN coatings.The main wear mechanism of TiNcoating prepared under optimal process parameters is micro-cutting wear accompanied by micro-fracture wear.

High temperature sliding wear behaviors of ion plating TiN composite coating with ion nitriding as interlayer on hot work die steel

High temperature sliding wear behaviors of ion plating TiN composite coating with ion nitriding interlayer on 3Cr2W8V hot work die steel substrate during 500～700 ℃ were investigated. Phase structure was analyzed by XRD and adhesion strength of TiN coating was measured by scratch test. The worn morphologies and wear mechanism of TiN composite coating were observed and analyzed by using SEM. The results showed that both adhesion strength and hardness of TiN composite coating with ion nitriding interlayer are higher than those of single TiN coating. Ion nitriding interlayer provides a stronger support for TiN coating. With increasing temperature, the wear rates and friction coefficient of all tested coatings increase. The wear resistance of TiN composite coating is better than that of single TiN coating. The wear mechanisms of TiN composite coating are mainly adhesion transfer wear and abrasive wear. The adhesion transfer wear becomes more severe as the test temperature increases. [

Pulsed DC plasma enhanced chemical vapor deposited TiN/Ti(C,N) multilayer coatings

TiN single coatings and TiN/Ti(C,N) multilayer coatings deposited on Cr12MoV substrate have been completed by pulsed DC plasma enhanced chemical vapor deposition(PCVD) process. The SEM, XRD and microvicker’s hardness as well as the indentation test were used to study the microstructure and mechanical properties of TiN/Ti(C,N) multilayer coatings. The results show that TiN/Ti(C,N) coatings are fine and have free column structure, and carbon atoms take the place of some nitrogen atoms in Ti(C,N) coatings when lower flow ratio of CH 4 is used. The microvicker’s hardness and interfacial adhesion between TiN/Ti(C,N) coatings and Cr12MoV substrate increases more obviously than that of TiN single hard coatings due to the more dense and free column structure when process is optimized.

Spinel Li Mn_(2)O_(4)integrated with coating and doping by Sn self-segregation

The development of high-performance and low-cost cathode materials is of great significance for the progress in lithium-ion batteries.The use of Co and even Ni is not conducive to the sustainable and healthy development of the power battery industry owing to their high cost and limited resources.Here,we report LiMn_(2)O_(4)integrated with coating and doping by Sn self-segregation.Auger electron energy spectrum and soft X-ray absorption spectrum show that the coating is Sn-rich LiMn_(2)O_(4),with a small Sn doping in the bulk phase.The integration strategy can not only mitigate the Jahn–Teller distortion but also effectively avoid the dissolution of manganese.The as-obtained product demonstrates superior high initial capacities of 124 mAh·g^(-1)and 120 mAh·g^(-1)with the capacity retention of 91.1%and 90.2%at 25℃and55℃after 50 cycles,respectively.This novel material-processing method highlights a new development direction for the progress of cathode materials for lithium-ion batteries.

IMPROVEMENT OF ADHESION BETWEEN ION PLATED TiN COATING AND BASE METAL BY ADDING Y

The adhesion between the ion plated TiN coating and the base metal is improved by adding Y.The machenism of the effect of Y has been discussed as well.

Reactive Plasma Sprayed TiN Coating and Its Thermal Stability

TiN coating was prepared by reactive plasma spraying in the Ar and N2 containing plasma jet. The resuits of XRD show that the TiN coating consists of TiN and Ti3 O, neither Ti2 N nor TiO2 phases. The toughening mechanism was characterized by analyzing the SEM morphologies of the TiN coating＇s indentation of microhardness and fracture surfaces. The results indicate that the coating possesses a high toughness. The adhesion strength among the TiN layers is 25.88 MPa, which is slightly lower than that of the Ni/AI bonding coating. The oxidation process of the RPS TiN coating is TiN→Ti3 O→TiO2.

The Stress Distribution and Thermal Behavior of TiBN and TiBN TiN Coatings in Milling AISI H13 Work Tool Steel

The FEM model of TiBN and TiBN/TiN coated cutting tool in milling of H13 steel w as developed. Process variables such as temperature and stress in the coating l ayer as well as in the substrate were analyzed. The efficacy of the present FEM analysis was verified by conducting controlled milling experiments on AISI H13 t o collect the relevant tool life and force data.The results show that the stress in a coated tool can significantly be reduced compared to an uncoated cutting t ool,possibly due to surface coatings improving the tribological properties of cu tting tools.Coatings with good thermal properties also help to improve the therm al behavior of cutting tool.