Effects of Predeformation on the Reverse Martensitic Transformation of TiNi Shape Memory Alloy

DSC was used to study the effects of predeformation on the reverse martensitic transformation of near-equiatomic TiNi alloy. Both the start temperature As and the finish temperature Af of the reverse transformation increased with increasing degree of predeformation, but the algebraic difference between As and Af decreased with increasing predeformation until it reached a minimum value, then remained unchanged with further deformation. Transformation heat also increased with increasing predeformation until it reached a maximum value, then decreased with further predeformation. All the phenomena above were considered to be closely related with the release of elastic strain energy during predeformation.

Microstructure and properties of laser micro welded joint of TiNi shape memory alloy

Butt welding of 0.2 mm-thick TiNi shape memory alloy sheet （SMA） was carried out using impulse laser, and tensile strength, fracture morphology, microstructure and phase change behaviour of welded joint were studied. The results show that using impulse laser can realize good butt welding of TiNi SMA sheet, tensile strength of welded joint is 683 MPa, which achieves 97% of that of cold rolled base metal, and the fracture mode of welded joint is ductile type as well as base metal. The welded joint can be divided into four zones according to grain size and microstructure. The microstructures of welded seam center zone are fine equiaxed crystals and the microstructures of both lower surface and upper surface edge zones are columnar crystals. When welded joint is vacuum annealed after welding, the phase transformation process is basically similar to the annealed base metal.

Effect of Thermal Cycling under Load on Martensite Transformation and Two-way Shape Memory Effect in a TiNi Alloy

The effect of thermal cycling under loading on martensitic transformation and two-way shape memory effect was investigated for Ti-49.8 at, pet Ni alloy. It is shown that M(s), and M(f) temperature increase with increasing the number of cycles, while A(s) and A(f) temperature decrease during thermal cycling. The total strain at and permanent strain epsilon (p) increase with increasing applied stress and number of cycles. The two-way shape memory effect can be improved by proper thermal cycling training under loading, while excessively high applied stress results in the deterioration of TWSME. The reason for the changes in martensitic transformation characteristics and two-way shape memory effect during thermal cycling under loading is discussed based on the analysis of microstructure by TEM observations.

Surface modification with SiO_2 coating on biomedical TiNi shape memory alloy by sol-gel method

The effect of heat treatment on the transformation temperature of Ti?52.2%Ni (mole fraction) alloy was studied using differential scanning calorimetry (DSC). The transformation temperatures of the alloy can be adjusted effectively by heat treatment. Dense and stable SiO2 coatings were deposited on the surface of the pre-oxidized TiNi alloy by sol?gel method. The bonding strength of films and matrix was (65.9±1.5) N. The electrochemical corrosion test shows that the TiNi alloy with SiO2 coating has excellent corrosion resistance in the Hank’s simulated body fluid. The release behaviors of Ni ion of the alloy with and without SiO2 coating implanted in the acoustic vesicle of guinea pig were studied by EDS testing, which was inhibited effectively by the dense and stable SiO2 coating on the alloy.

Influence of recovery heating rate on shape memory effect in up-quenched Cu-Al-Mn alloy

The effect of recovery heating rate on shape memory effect of the up-quenched Cu-8.88Al-10.27Mn（mass fraction, %） alloy was investigated by optical microscopy, electron transmission microscopy（TEM） and electrical resistivity measurement. It is found that the shape recovery rate decreases as the heating rate decreases. It can reach 75% when the heating rate is 20 ℃/min, while it is only 8% when the heating rate is 1 ℃/min. In situ microstructure observation indicates that the dependence of shape memory effect on recovery heating rate is caused by the stabilization of twinned martensite induced by deformation. The analysis of electrical resistivity shows that the stabilization of twinned martensite may be ascribed to formation of compound defects of vacancies and dislocations at the boundaries of twinned martensite during the slow heating. The compound defects prevent the reverse transformation of twinned martensite.

Role of thermal martensite in shape memory effect of CoAl and CoNi alloys

To address the role of the HCP martensite in CoAl and CoNi shape memory alloys, the relationship between the shape memory effect （SME） and the content of the thermal and stress-induced HCP martensite was investigated in the solution-treated CoAl and CoNi alloys. In-situ optical observations were employed to investigate the contents of thermal HCP martensite before and after deep cooling and its influence on the stress-induced HCP martensite transformation and SME. The results show that the SME in both the CoAl and the CoNi alloys results from the stress-induced HCP martensite. The role of the thermal HCP martensite in both of them is the strengthening of the matrix. The much higher yield strength in the solution-treated CoAl alloy due to solution strengthening of Al is responsible for its better SME compared with the CoNi alloy.

Microstructures and properties of capacitor discharge welded joint of TiNi shape memory alloy and stainless steel

Microstructures and properties of capacitor discharge welded （CDW） joint of TiNi shape memory alloy （ SMA ） and stainless steel （SS） were studied. The fracture characteristics of the joint were analyzed by means of scanning electron microscope （ SEM）. Microstructures of the joint were examined by means of optical microscope and SEM. The results showed that the teusile strength of the inhomogeneous joint （ TiNi-SS joint） was low and the joint was brittle. Because TiNi SMA and SS melted, a brittle as-cast structure and compound were formed in the weld. The tensile strength and the shape memory effect （SME） of TiNi-SS joint were strongly influenced by the changes of composition and structure of the weld. Measures should be taken to prevent defects from forming and extruding excessive molten metal in the weld for improving the properties of TiNi-SS joint.

PREPARATION OF TiNi SHAPE MEMORY ALLOY POROSINT BY SHS

TiNi shape memory alloy porosint, a promising artificial bone material, was prepared by self propagating high temperature synthesis method. It is found that the key technical parameter affecting the porosity, the shape and distribution of the bores in the synthesized product is the pre heating temperature of green compact. While the pre heating temperature varies between 523 K and 673 K, the TiNi shape memory alloy porosint with wholly homogeneously distributing bores will be gained. The porosity of the porosint is 70% when the pre heating temperature is near 673 K, which is maximal under different pre heating temperatures. The compressive strength of TiNi SMA porosint with a porosity of 70% manufactured by SHS is up to 100 MPa and the percentage recovered is 92%.

Effect of Training on Two-way Shape Memory Effect and Its Stability in a Ti-Ni-Hf High Temperature Shape Memory Alloy

The Effect of the thermal cycling training under constant strain on the two-way shape memory effect (TWSME) in a Ti36l\li49Hf15 high temperature shape memory alloy (SMA) has been investigated by bending tests. The results indicated that the training procedure is beneficial to get the better TWSME. The two-way shape memory strain increases with increasing the training strain. And it decreases with increasing the training temperature. The TWSME obtained in the present alloy shows poorer stability compared with that obtained in the TiNi alloys.

The Reverse Transformation Behavior of TiNi Shape Memory Alloy Wires Prestrained at Different Temperatures

The reverse transformation behavior of TiNi alloy wires prestrained at different temperatures is studied in this paper. Experimental results show that prestrain at different temperatures obviously affects the reverse transformation behavior of the TiNi alloy wire. A single peak appears on the DSC curves of wires prestrained at 253-313K (in the martensite state). However deformed at 333K, three consecutive peaks appear on the DSC curves of wires with a smaller prestrain and a single peak appears on the DSC curves of the wires with a larger prestrain. The recovery strain ratio of the wires prestrained at 253-313K are very similar. However, the ratio of the wire predeformed at 333K is obviously smaller than that of the wire prestrained in the martensite state.

Microstructure,compression property and shape memory effect of Ru-Nb high temperature shape memory alloy

The microstructure,phase transformation,compression property and strain recovery characteristics of equiatomic Ru-Nb high temperature shape memory alloy were investigated by means of optical microscope,X-ray diffraction(XRD),differential scanning calorimetry(DSC),compression tests and transmission electron microscopy(TEM).When cooling the alloy specimen from high temperature to room temperature,β(parent phase)→β’(interphase)→β″(martensite) two step phase transformation occurs.The microstructure at room temperature shows regularly arranged band morphology with the monoclinic crystal structure.The twinning relationship between the martensite bands was determined to be(101) Type I.Reorientation and of the martensite bands inside the variant and dislocation were found during compression at room temperature.The maximum complete recovery strain is about 1.5%.

Reverse Transformation Behavior of TiNi Shape Memory Alloys Prestrained in the Parent Phase

The reverse martensitic transformation of TiNi alloy wires prestrained in the parent phase was studied. Experimental results shou, that the reverse transformation of the TiNi allogys prestrained in the parent phase is significantly different from that of the TiNi alloys prestrained in the martensite phase. Three continual peaks appear on the DSC curves of wires with a small prestrain and one high temperature peak appears on the DSC curves of wires with a large prestrain.

MICROSTRUCTURE AND REVERSE SHAPE MEMORY EFFECT IN A Cu-Zn-Al ALLOY

The bainite structure in a Cu-Zn-A1 alloy related to the reverse shape memory effect has been observed by means of TEM.The reverse memory effect may be improved by up to one order of magnitude under applied constraint stress.The widespread propagation of bainite was confirmed to be the diffusion controlled shear process by the parabolic configuration of side interface of bainite plate and the twisting of intersected bainite plates.

Two-way Shape Memory Effect in a Ti-Ni-Nb Shape Memory Alloy with Wide Hysteresis

A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the microstructure after training. the mechanism of TWSME in the Ti46.3 Ni44.7Nb9 alloy has been discussed.

Shape Memory Effect of As-aged Fe-14Mn-5Si-8Cr-4Ni-0.2C Alloy

The effects of aging temperature on shape memory effect, mechanical properties and microstruc-ture of Fe-14Mn-5Si-8Cr-4Ni-0.2C shape memory alloy have been studied. The results showed that the second phase particles rich in chromium, manganese and silicon precipitate during aging, and thereby increase the hardness and strength of the alloy. The shape recovery ratio can be remarkably improved by aging and a maximum value can be obtained at 1223 K, which is 68% higher than that of the specimen in solid solution state. When the aging temperature is below 1223 K, the amount of second phase particles increases as the aging temperature increases. The size of austenite grain increases with increasing aging temperature. When the temperature is over 1223 K, the second phase particles can not precipitate. The lack of second phase particles and the increase of grain size make the hardness and shape recovery ratio drastically decrease, when the temperature is over 1223 K.

Effect of Ageing on Martensitic Transformation and Shape Memory Effect of Fe-Mn-Si-Co-Mo Alloy

This paper discusses the effect of ageing on the thermally induced martensitic transformation and its reverse transformation and shape memory effect of Fe-24Mn-5Si-8Co-4Mo shape memory alloy:the precipitation of Fe 2Mo particles increases the hardness and strength of the alloy as ageing goes on;ageing increases the transformation temperatures;ageing improves,the SME of the alloy so remarkably that a maximum shape recovery ratio is obtained while ageing at 600℃.

INFLUENCE OF PROCESSING ON SHAPE MEMORY EFFECT OF Fe-Mn-Si-Ni-C-RE SHAPE MEMORY ALLOY

Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃, ε → γ transition completed in 10s meanwhile the relative shape recovery ratio of the alloy increased rapidly.

Effect of Compound Rare Earth on Shape Memory Effect of Fe-Mn-Si-Ni-C Alloys

Effect of compound rare earth (RE) on shape memory effect (SME) of Fe-Mn-Si-Ni-C shape memory alloy was studied by bent measurement,thermal cycle training, SEM and XRD etc. The results show that metallurgic microstructure is refined and SME improved evidently with the addition of compound RE. The alloy appears little two-way shape memory effect. The former training and addition of compound RE are two effective ways to restrain martensitic stability. XRD analysis also indicates that ε→γ reversible transition ratio increases by training greatly help to improve SME of the alloy.

HIGH TEMPERATURE SHAPE MEMORY EFFECT AND PRE-DEFORMATION FOR Ti_(50) Ni_(13) Pd_(37) ALLOY

The dependence of high temperature shape memory effect on the pre-deformation tempera- ture of the Ti_(50)Ni_3Pd_(37) alloy has been studied.This alloy,of which the reverse transformation start temperature on heating is 620 K,has both one-way and two-way shape memory effects. The maximum shape memory strain of the ahoy may be obtained under pre-deformation in the range of 620 to 640 K.This seems to be related to the minimum recoverable strain energy emerged from the above mentioned temperature range.

Effect of chemical component on shape memory effect of Fe-Mn-Si-Ni-C-RE shape memory alloy

Effect of chemical component on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloys was studied by bent measurement, thermal cycle training, SEM etc. Results of study indicate that the alloys with high Mn content (25%) appeare better SME, especially in lower strain. SME improves evidently when Si is higher content, especially it’s range from 3% up to 4%. But brittleness of Fe-Mn-Si-Ni-C-RE alloy increases by increasing the Si content. SME of the alloy is weakening gradually as carbon content increases under small strain (3%). But in the condition of large strain (above 6%), SME of the alloy whose carbon content ranges from 0.1 % to 0.12% shows small decreasing range, especially of alloy with the addition of compound RE.