Shear Behaviors of Steel-Plate Connections for Timber-Concrete Composite Beams with Prefabricated Concrete Slabs

To promote the development of timber-concrete composite(TCC)structures,it is necessary to propose the assembly-type connections with high assembly efficiency and shear performances.This article presented the experimental results of the innovative steel-plate connections for TCC beams using prefabricated concrete slabs.The steel-plate connections consisted of the screws and the steel-plates.The steel-plates were partly embedded in the concrete slabs.The concrete slabs and the timber beams were connected by screws through the steel-plates.The parameters researched in this article included screw number,angle steel as the reinforcement for anchoring,and shallow notches on the timber surface to restrict the slip of the steel-plates.Experimental results were discussed in terms of failure modes,ultimate bearing capacities,and slip moduli.It was found that increasing the number of screws could lead to the obvious improvement on the ultimate bearing capacities and the slip moduli at the ultimate state;and the angle steel as the reinforcement showed the slight influence on the ultimate bearing capacities and the slip moduli.The application of the shallow notch can greatly improve the ultimate bearing capacities and the slip moduli.The calculation models for the ultimate bearing capacities and the slip moduli of the steel-plate connections with and without shallow notches were proposed,which showed good accuracy compared with the experimental results.

Theoretical Analysis on Deflection and Bearing Capacity of Prestressed Bamboo-Steel Composite Beams

A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.

Experimental study on ultimate flexural capacity of steel encased concrete composite beams

Based on the experimental study and inelastic theory, the ultimate flexuralcapacity of steel encased concrete composite beams are derived. The difference between steel encasedconcrete composite beams with full shear connection and beams with partial shear connection,together with the relationship between the inelastic neutral axis of steel parts and concrete parts,are considered in the formulae. The calculation results of the eight specimens with full shearconnection and the three specimens with partial shear connection are in good agreement with theexperimental data, which validates the effectiveness and efficiency of the proposed calculationmethods. Furthermore, the nonlinear finite element analysis of the ultimate flexural capacity of thesteel encased concrete composite beams is performed. Nonlinear material properties and nonlinearcontact properties are considered in the finite element analysis. The finite element analyticalresults also correlate well with the experimental data.

Ultimate negative bending-moment capacity of outer-plated steel-concrete continuous composite beams

Static load tests and bearing capacity analyses are carried out for two outer-plated steel-concrete continuous composite beams. The load-deflection curve and the load-strain curve of specimens are obtained and analyzed. The test results indicate that effective cooperation can be achieved by the shearresistant connection between the reinforcement in the negative moment area and the outer-plated steel beam, and the overall working performance of the composite beams is favorable. At the load-bearing limiting state, the plastic strain on the maximum negative and positive moment section becomes fully developed so as to form relatively ideal plastic hinges. With the increase in the reinforcement ratio, the moment-carrying capacity of the composite beams improves significantly, but the ductility of the beams and the rotation ability of the plastic hinges decrease. The formulae for calculating the limit bending capacity in the negative moment area of outer-plated steel-concrete composite beams are proposed based on the test data. The calculated results agree well with the test results.

Flexural behaviors of steel reinforced ECC/concrete composite beams

An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increase the ductility and crack resisting ability of the beam. Based on the assumption of the plane remaining plane and the simplified constitutive models of materials, the stress and strain distributions along the depth of the composite beam in different loading stages are comprehensively investigated to obtain calculation methods of the load-carrying capacities for different stages. Also, a simplified formula for the ultimate load carrying capacity is proposed according to the Chinese code for the design of concrete structures. The relationship between the moment and curvature for the composite beam is also proposed together with a simplified calculation method for ductility of the ECC/RC composite beam. Finally, the calculation method is demonstrated with the test results of a composite beam. Comparison results show that the calculation results have good consistency with the test results, proving that the proposed calculation methods are reliable with a certain theoretical significance and reference value.

Nonlinear analysis on electrical properties in a bended composite piezoelectric semiconductor beam

In this paper,the interactions between the transverse loads and the electrical field quantities are investigated based on the nonlinear constitutive relation.By considering a composite beam consisting of a piezoelectric semiconductor and elastic layers,the nonlinear model is established based on the phenomenological theory and Euler’s beam theory.Furthermore,an iteration procedure based on the differential quadrature method(DQM)is developed to solve the nonlinear governing equations.Before analysis,the convergence and correctness are surveyed.It is found that the convergence of the proposed iteration is fast.Then,the transverse pressure induced electrical field quantities are investigated in detail.From the calculated results,it can be found that the consideration of nonlinear constitutive relation is necessary for a beam undergoing a large load.Compared with the linear results,the consideration of the nonlinear constitutive relation breaks the symmetry for the electric potential,the electric field,and the perturbation carrier density,and has little influence on the electric displacement.Furthermore,the non-uniform pressures are considered.The results show that the distributions of the electric field quantities are sensitively altered.It indicates that the electrical properties can be manipulated with the design of different transverse loads.The conclusions in this paper could be the guidance on designing and manufacturing electronic devices accurately.

Modeling and Free Vibration Behavior of Rotating Composite Thin-walled Closed-section Beams with SMA Fibers

Smart structure with active materials embedded in a rotating composite thin-walled beam is a class of typical structure which is using in study of vibration control of helicopter blades and wind turbine blades. The dynamic behavior investigation of these structures has significance in theory and practice. However, so far dynamic study on the above-mentioned structures is limited only the rotating composite beams with piezoelectric actuation. The free vibration of the rotating composite thin-walled beams with shape memory alloy（SMA） fiber actuation is studied. SMA fiber actuators are embedded into the walls of the composite beam. The equations of motion are derived based on Hamilton＇s principle and the asymptotically correct constitutive relation of single-cell cross-section accounting for SMA fiber actuation. The partial differential equations of motion are reduced to the ordinary differential equations of motion by using the Galerkin＇s method. The formulation for free vibration analysis includes anisotropy, pitch and precone angle, centrifugal force and SMA actuation effect. Numerical results of natural frequency are obtained for two configuration composite beams. It is shown that natural frequencies of the composite thin-walled beam decrease as SMA fiber volume and initial strain increase and the decrease in natural frequency becomes more significant as SMA fiber volume increases. The actuation performance of SMA fibers is found to be closely related to the rotational speeds and ply-angle. In addition, the effect of the pitch angle appears to be more significant for the lower-bending mode ones. Finally, in all cases, the precone angle appears to have marginal effect on free vibration frequencies. The developed model can be capable of describing natural vibration behaviors of rotating composite thin-walled beam with active SMA fiber actuation. The present work extends the previous analysis done for modeling passive rotating composite thin-walled beam.

Experimental study on hysteretic behavior of prestressed truss concrete composite beams

This paper describes an experimental study of the hysteretic behavior of prestressed truss concrete composite beams （PTCCBs） under cyclic loading. Five beam models were designed and tested, in which the testing parameters include the global reinforcement index β0, the prestress level 2 and the ratio of stirrup ρsv in the potential plastic hinge zones. Based on the test results, the failure mode and hysteretic behavior of the tested models are obtained. In addition, the P-△ and sectional M-φ hysteretic models for the PTCCBs at the midspan are established. The P-△ hysteretic model shows good agreement with the test results.

Vibration of composite beams with two overlapping delaminations

Delaminations in composite laminates may de-velop from small cracks due to fabrication and impact load-ing,or from places of high stress concentration.The locationsof the delaminations are not determinate.In this research,ananalytical solution for the free vibration of a composite beamwith two overlapping delaminations is presented.The dela-minated beam is analyzed as seven interconnected beamsusing the delaminations as their boundaries.The continuityand equilibrium conditions are satisfied between the adjoin-ing regions of the beams.Classical beam theory is applied toeach of the beams.Complex vibration behaviors emerge fordifferent sizes and locations of the delaminations.Compar-ison with analytical results reported in the literature verifiesthe validity of the present solution.

Closed-form solution for shear lag effects of steel-concrete composite box beams considering shear deformation and slip

Based on the consideration of longitudinal warp caused by shear lag effects on concrete slabs and bottom plates of steel beams,shear deformation of steel beams and interface slip between steel beams and concrete slabs,the governing differential equations and boundary conditions of the steel-concrete composite box beams under lateral loading were derived using energy-variational method.The closed-form solutions for stress,deflection and slip of box beams under lateral loading were obtained,and the comparison of the analytical results and the experimental results for steel-concrete composite box beams under concentrated loading or uniform loading verifies the closed-form solution.The investigation of the parameters of load effects on composite box beams shows that:1) Slip stiffness has considerable impact on mid-span deflection and end slip when it is comparatively small;the mid-span deflection and end slip decrease significantly with the increase of slip stiffness,but when the slip stiffness reaches a certain value,its impact on mid-span deflection and end slip decreases to be negligible.2) The shear deformation has certain influence on mid-span deflection,and the larger the load is,the greater the influence is.3) The impact of shear deformation on end slip can be neglected.4) The strain of bottom plate of steel beam decreases with the increase of slip stiffness,while the shear lag effect becomes more significant.

Composite optical vortices in noncollinear Laguerre–Gaussian beams and their propagation in free space

Taking two Laguerre-Gaussian beams with topological charge 1 = ±1 as an example, this paper studies the composite optical vortices formed by two noncollinear Laguerre-Gaussian beams with different phases, amplitudes, waist widths, off-axis distances, and their propagation in free space. It is shown by detailed numerical illustrative examples that the number and location of composite vortices at the waist plane are variable by varying the relative phase β, amplitude ratio η, waist width ratio ξ, or off-axis distance ratio μ. The net topological charge lnet is not always equal to the sum lsum of charges of the two component beams. The motion, creation and annihilation of composite vortices take place in the free-space propagation, and the net charge during the propagation remains unchanged and equals to the net charge at the waist plane.

Flexural behavior of reinforced concrete beams with high performance fiber reinforced cementitious composites

This article presents an experimental study on the flexural performance of reinforced concrete(RC)beams with fiber reinforced cementitious composites(FRCC)and hybrid fiber reinforced cementitious composites(HFRCC)in the hinge portion.Beam specimens with moderate confinement were used in the study and tested under monotonic loading.Seven diverse types of FRCC including hybrid composites using fibers in different profiles and in different volumes are employed in this study.Companion specimens such as cylindrical specimens and prism specimens are also used to study the physical properties of composites employed.The moment?curvature,stiffness behavior,ductility,crack pattern and modified flexural damage ratio are the main factors considered in this study to observe the efficacy of the employed hybrid composites.The experimental outputs demonstrate the improved post yield behavior with less rate of stiffness degradation and better damage tolerance capacity than conventional technique.

Flexural behavior of steel reinforced engineered cementitious composite beams

In order to enhance the durability of steel encased concrete beams, a new type of steel reinforced engineered cementitious composite(SRECC) beam composed of steel shapes, steel bars and ECC is proposed. The theoretical analyses of the SRECC beam including crack propagation and stress-strain distributions along the depth of the composite beam in different loading stages are conducted. A theoretical model and simplified design method are proposed to calculate the load carrying capacity. Based on the proposed theoretical model, the relationship between the moment and corresponding curvature is derived. The theoretical results are verified with the finite element analysis. Finally, an extensive parametric study is performed to study the effect of the matrix type, steel shape ratio, reinforced bar ratio, ECC compressive strength and ECC tensile ductility on the mechanical behavior of SRECC beams. The results show that substitution concrete with ECC can effectively improve the bearing capacity and ductility of composite beams. The steel shape and longitudinal reinforcement can enhance the loading carrying capacity, while the ductility decreases with the increase of steel shape ratio. ECC compressive strength has significant effects on both load carrying capacity and ductility, and changing the ultimate strain of ECC results in a very limited variation in the mechanical behavior of SRECC beams.

Flexural behavior of composite beams after the ultimate limit state externally strengthened with CFRP sheets bonded with high-temperature resistant matrix

In this paper the alkali-activated slag cementitious materials(AASCM)which strength at 600 ℃ is larger than that of AASCM at room temperature,were prepared to paste CFRP sheets to strengthen four simply supported unbonded prestressed composite beams encased circular steel tube truss after ultimate limit state.Test on flexural behavior of these four beams was performed.Moreover,normal section load-bearing capacity of these beams and the curve load-deflection at mid-span were obtained.Experimental results show that it is feasible to strengthen concrete members with CFRP sheets bonded with AASCM.Based on the experimental results and theoretical study,computational method of stiffness is proposed for calculating bending rigidity and normal section load-bearing capacity of concrete simply supported beams strengthened with CFRP sheets bonded with AASCM.Formula of bending rigidity calculation was founded which results are in good agreement with testing data.

Numerical Investigation of Connection Performance of Timber-Concrete Composite Slabs with Inclined Self-Tapping Screws under High Temperature

The timber-concrete composite(TCC)slabs have become a preferred choice of floor systems in modern multi story timber buildings.This TCC slab consisted of timber and a concrete slab which were commonly connected together with inclined self-tapping screws(STSs).To more accurately predict the fire performance of TCC slabs,the mechanical behavior of TCC connections under high temperature was investigated by numerical simulation in this study.The interface slip of TCC connections was simulated by a proposed Finite Element(FE)model at room temperature,and different diameter and penetration length screws were considered.The effectiveness of this FE model was validated by comparing with the existing experimental results.Furthermore,the sequentially coupling thermal stress analyses of this model were conducted,and the relationship between the reduction coefficient of connection performance and the effective penetration length of screws was summarized.This study gave the fit-ting expressions for the reduction coefficient of slip modulus and joint strength.Finally,the numerical investiga-tions of the fire performance of TCC slabs considering the char fall-off of Cross Laminated Timber(CLT)were performed to verify the effectiveness of the proposed reduction law.Comparing the fire-resistance time with experimental results showed deviation of the proposed model was−14.02%.

Mechanical performance of shear studs and application in steel-concrete composite beams

This work experimentally investigates the effects of shear stud characteristics on the interface slippage of steel-concrete composite push-out specimens. ABAQUS is used to establish a detailed 3D finite element(FE) model and analyze the behavior of push-out specimens. The modeling results are in good agreement with the experimental results. Based on parametrical analysis using the validated FE approaches, the effects of important design parameters, such as the diameter, number, length to diameter ratio, and yield strength of studs, concrete strength and steel transverse reinforcement ratio, on the load-slip relationship at the interface of composite beams are discussed. In addition, a simplified approach to model studs is developed using virtual springs with an equivalent stiffness. This approach is demonstrated to be able to predict the load-displacement response and ultimate bearing capacity of steel-concrete composite beams. The predicted results show satisfactory agreement with experimental results from the literature.

Nonlinear finite element analysis of steel-concrete composite beams

Proposes a simplified finite element model for steel-concrete composite beams. The effects of slip can be taken into account by creating a special matrix of shear connector stiffness and using the iteration method. Meanwhile, the effect of material non-linearity of steel and concrete on rigidity and strength of composite beams is considered. With the age-adjusted effective modulus method, the analysis for the whole process of shrinkage and creep under long-term load can be performed. The ultimate load, deflection, stress and slip of continuous composite beams under short-term and long-term load are computed using the proposed finite element model. The numerical results are compared with the experimental results and existing values based on other numerical methods, and are found to be in good agreement.

Analysis and seismic tests of composite shear walls with CFST columns and steel plate deep beams

A composite shear wall concept based on concrete filled steel tube （CFST） columns and steel plate （SP） deep beams is proposed and examined in this study. The new wall is composed of three different energy dissipation elements： CFST columns; SP deep beams; and reinforced concrete （RC） strips. The RC strips are intended to allow the core structural elements - the CFST columns and SP deep beams - to work as a single structure to consume energy. Six specimens of different configurations were tested under cyclic loading. The resulting data are analyzed herein. In addition, numerical simulations of the stress and damage processes for each specimen were carried out, and simulations were completed for a range of location and span-height ratio variations for the SP beams. The simulations show good agreement with the test results. The core structure exhibits a ductile yielding mechanism characteristic of strong column-weak beam structures, hysteretic curves are plump and the composite shear wall exhibits several seismic defense lines. The deformation of the shear wall specimens with encased CFST column and SP deep beam design appears to be closer to that of entire shear walls. Establishing optimal design parameters for the configuration of SP deep beams is pivotal to the best seismic behavior of the wall. The new composite shear wall is therefore suitable for use in the seismic design of building structures.

Shear deformable finite beam elements for composite box beams

The shear deformable thin-walled composite beams with closed cross-sections have been developed for coupled flexural, torsional, and buckling analyses. A theoretical model applicable to the thin-walled laminated composite box beams is presented by taking into account all the structural couplings coming from the material anisotropy and the shear deformation effects. The current composite beam includes the transverse shear and the restrained warping induced shear deformation by using the first-order shear deformation beam theory. Seven governing equations are derived for the coupled axial-flexural-torsional-shearing buckling based on the principle of minimum total potential energy. Based on the present analytical model, three different types of finite composite beam elements, namely, linear, quadratic and cubic elements are developed to analyze the flexural, torsional, and buckling problems. In order to demonstrate the accuracy and superiority of the beam theory and the finite beam elements developed by this study,numerical solutions are presented and compared with the results obtained by other researchers and the detailed threedimensional analysis results using the shell elements of ABAQUS. Especially, the influences of the modulus ratio and the simplified assumptions in stress-strain relations on the deflection, twisting angle, and critical buckling loads of composite box beams are investigated.

Design of the Composite Steel-Glass Beams with Semi-Rigid Polymer Adhesive Joint

New and high transparent structural element, steel-glass composite beam was developed in respect to fabrication, static-structural and architectural criteria and consists of steel flanges and glass web assembled together by semi-rigid polymer adhesive, which is the key element of whole composite system. These beams can be used mainly as members of high transparent roof or floor structure as well as stiffening fins for large area glass facades. This paper deals with experimental research performed at CTU （Czech Technical University） Prague, which started by adhesive selection and initial material tests by ISO527, continued via small-scale steel-glass connection tests and graduated by full-scale tests of hybrid beams with the span of 4 m. Generalized results of these experiments, analytical and numerical studies serve as device, how to accurately predict the behavior of the beam, describe the stress distribution along the cross section and safely and economically design such a kind of structure with semi-rigid shear connection, made by polymer adhesive.