Extraction of Valuable Metals from Titanium-bearing Blast Furnace Slag by Acid Leaching

To realize the resource utilization of the valuable metals in the titanium-containing blast furnace slag,the process route of “hydrochloric acid leaching-electrolysis-carbonization and carbon dioxide capture-preparation of calcium carbonate” was proposed.In this study,the influences of process conditions on the leaching rates of calcium,magnesium,aluminum,and iron and the phases of the leaching residue were investigated for the leaching process.The experimental results show that the HCl solution could selectively leach the elements from the titanium-containing blast furnace slag.The better leaching conditions are the HCl solution concentration of 4 mol/L,the leaching time of 30 min,the ratio of liquid volume to solid gas of 10 mL/g,and the stirring paddle speed of 300 r/min.Under the conditions,the leaching rates of calcium,magnesium,aluminum,and iron can reach 85.87%,73.41%,81.35%,and 59.08%,and the leaching rate of titanium is 10.71%.The iron and the aluminum are removed from the leachate to obtain iron-aluminum water purification agents,and the magnesium is removed from the leachate to obtain magnesium hydroxide.The leaching residue phase is dominated by perovskite,followed by magnesium silicate and tricalcium aluminate,and the titaniumrich material could be obtained from the leaching residue by desiliconization.

Simultaneous preparation of TiO2 and ammonium alum,and microporous SiO2 during the mineral carbonation of titanium-bearing blast furnace slag

In this study,a route for simultaneous mineralization of CO2 and production of titanium dioxide and ammonium alum,and microporous silicon dioxide from titanium-bearing blast furnace slag(TBBF slag)was proposed,which is comprised of(NH4)2 S04 roasting,acid leaching,ammonium alum crystallization,silicic acid flocculation and Ti hydrolysis.The effects of relevant process parameters were systematically investigated.The re sults showed that under the optimal roasting and leaching conditions about 85%of titanium and 84.6%of aluminum could be extracted while only 30%of silicon entered the leachate.84%of Al^3+was crystallized from the leachate in the form of ammonium aluminum sulfate dodecahydrate with a purity up to 99.5 wt%.About 85%of the soluble silicic acid was flocculated with the aid of secondary alcohol polyoxyethylene ether 9(AEO-9)to yield a microporous SiO2 material(97.4 wt%)from the crystallized mother liquor.The Al-and Si-depleted solution was then hydrolyzed to generate a titanium dioxide(99.1 wt%)with uniform particle size distribution.It was figured out that approximately 146 kg TiO2 could be produced from 1000 kg of TBBF slag.Therefore,the improved process is a promising method for industrial application.

Recent progress of efficient utilization of titanium-bearing blast furnace slag

Titanium-bearing blast furnace slag(BFS)has valuable compositions and potential environmental hazardousness.Thus,developing efficient and green approaches to utilize BFS is highly desired for resource economization and environmental protection.In the past decades,many attempts have been adopted to reuse BFS efficiently,and significant advances in understanding the fundamental features and the development of efficient approaches have been achieved.This review provides a comprehensive overview of the latest progress on the efficient utilization of BFS and discusses the mechanism and characteristics of various approaches,along with their application prospects.In particular,the extraction and enrichment of titanium-bearing phases from BFS are highlighted because of the high availability of titanium resources.This systemic and comprehensive review may benefit the design of new and green utilization routes with high efficiency and low cost.

Antibacterial Properties of V-doped Titanium-bearing Blast Furnace Slag Prepared at Different Calcination Temperatures

Perovskite-type V-doped titanium-bearing blast furnace slag (VTBBFS) photocatalyst was prepared by high-temperature solid phase method.The influence of calcination temperature on the photocatalytic and antibacterial properties of VTBBFS was studied in details.Its composition and microstructure were evaluated by X-ray diffractometer,ultraviolet-visible absorption spectrometer,Fourier transform infrared spectrometer and scanning electron microscope.The antibacterial properties of VTBBFS to Candida albicans were investigated by flask oscillation method.The results showed that the optical absorption and antibacterial properties of VTBBFS were the best with 10%(ω) doping of vanadium,prepared at 800℃ for 2 h,and its sterilization rate was close to 100% to Candida albicans (ATCC10231).The minimum inhibitory and minimum bactericidal concentrations were 25 and 50 mg/mL.When the concentration was 0.2 μg/mL,the catalyst had the least toxic toxicity.

Recovery of titanium,aluminum,magnesium and separating silicon from titanium-bearing blast furnace slag by sulfuric acid curing-leaching

An energy-efficient route was adopted to treat titanium-bearing blast furnace slag(TBBFS)in this study.Titanium,aluminum,and magnesium were simultaneously extracted and silicon was separated by low temperature sulfuric acid curing and low concentration sulfuric acid leaching.The process parameters of sulfuric acid curing TBBFS were systematically studied.Under the optimal conditions,the recovery of titanium,aluminum,and magnesium reached 85.96%,81.17%,and 93.82%,respectively.The rapid leaching model was used to limit the dissolution and polymerization of silicon,and the dissolution of silicon was only 3.18%.The mechanism of sulfuric acid curing-leaching was investigated.During the curing process,the reaction occurred rapidly and released heat massively.Under the attack of hydrogen ions,the structure of TBBFS was destroyed,silicate was depolymerized to form filterable silica,and titanium,magnesium,aluminum,and calcium ions were replaced to form sulfates and enriched on the surface of silica particles.Titanium,aluminum,and magnesium were recovered in the leaching solution,and calcium sulfate and silica were enriched in the residue after leaching.This method could effectively avoid the formation of silica sol during the leaching process and accelerate the solid-liquid separation.

Preparation,characterization and photocatalytic activity of sulfuric acid-modified titanium-bearing blast furnace slag

The feasibility of reducing Cr(VI)from the aqueous solution by sulfuric acid-modified titanium-bearing blast furnace slag(SATBBFS)as a photocatalyst was investigated.The photocatalysts were examined by X-ray diffraction(XRD),UV-vis diffuse reflectance spectra,thermogravimetric analysis(TG)and Fourier transform infrared spectroscopy(FTIR).The photocatalytic activities of the different catalysts were evaluated by the photocatalytic reduction of Cr(VI)under UV-vis light irradiation.The results show that the photocatalytic activities of SATBBFS catalysts are strongly dependent on CaTiO3-to-TiO2 mass ratio,adsorption capacity and surface acidity,and SATBBFS calcined at 400°C shows a higher photocatalytic activity compared with other catalysts.

Effect of cooling rate on the crystallization behavior of perovskite in high titanium-bearing blast furnace slag

The effect of cooling rate on the crystallization of perovskite in high Ti-bearing blast furnace（BF） slag was studied using confocal scanning laser microscopy（CSLM）. Results showed that perovskite was the primary phase formed during the cooling of slag. On the slag surface, the growth of perovskite proceeded via the successive production of quasi-particles along straight lines, which further extended in certain directions. The morphology and structure of perovskite was found to vary as a function of cooling rate. At cooling rates of 10 and 30 K/min, the dendritic arms of perovskite crossed obliquely, while they were orthogonal at a cooling rate of 20 K/min and hexagonal at cooling rates of 40 and 50 K/min. These three crystal morphologies thus obtained at different cooling rates respectively corresponded to the orthorhombic, cubic and hexagonal crystal structures of perovskite. The observed change in the structure of perovskite could probably be attributed to the deficiency of O^2-, when Ti2O3 was involved in the formation of perovskite.

Indirect mineral carbonation of titanium-bearing blast furnace slag coupled with recovery of TiO_2 and Al_2O_3

Large quantities of CO_2 and blast furnace slag are discharged in the iron and steel industry. Mineral carbonation of blast furnace slag can offer substantial CO_2 emission reduction and comprehensive utilization of the solid waste.This paper describes a novel route for indirect mineral carbonation of titanium-bearing blast furnace(TBBF) slag,in which the TBBF slag is roasted with recyclable(NH_4)_2SO_4(AS) at low temperatures and converted into the sulphates of various valuable metals, including calcium, magnesium, aluminium and titanium. High value added Ti-and Al-rich products can be obtained through stepwise precipitation of the leaching solution from the roasted slag. The NH_3 produced during the roasting is used to capture CO_2 from flue gases. The NH_4HCO_3 and(NH_4)_2CO_3 thus obtained are used to carbonate the CaSO_4-containing leaching residue and MgSO_4-rich leaching solution, respectively. In this study, the process parameters and efficiency for the roasting, carbonation and Ti and Al recovery were investigated in detail. The results showed that the sulfation ratios of calcium,magnesium, titanium and aluminium reached 92.6%, 87% and 84.4%, respectively, after roasting at an AS-to-TBBF slag mass ratio of 2:1 and 350 °C for 2 h. The leaching solution was subjected to hydrolysis at 102 °C for 4 h with a Ti hydrolysis ratio of 95.7% and the purity of TiO_2 in the calcined hydrolysate reached 98 wt%.99.7% of aluminium in the Ti-depleted leaching solution was precipitated by using NH_3. The carbonation products of Ca and Mg were CaCO_3 and(NH_4)_2 Mg(CO_3)_2·4H_2O, respectively. The latter can be decomposed into MgCO_3 at 100–200 °C with simultaneous recovery of the NH_3 for reuse. In this process, approximately 82.1% of Ca and 84.2%of Mg in the TBBF slag were transformed into stable carbonates and the total CO_2 sequestration capacity per ton of TBBF slag reached up to 239.7 kg. The TiO_2 obtained can be used directly as an end product, while the Al-rich precipitate and the two carbonation products can act, respectively, as raw materials for electrolytic aluminium,cement and light magnesium carbonate production for the replacement of natural resources.

Analysis and Prospect of Waste Heat Utilization from Blast Furnace Slag Flushing

Estimating the residual heat of blast furnace slag flushing in China,classifying and introducing the current proposed methods of slag flushing waste heat utilization,and listing existing cases.In order to better save energy and water in the slag flushing process of blast furnaces,an ideal comprehensive cascade utilization system scheme for annual recovery of waste heat is proposed.Based on the measured waste heat data of a steel plant,design calculations are carried out to further analyze the economic feasibility of the new scheme and provide reference for its promotion and application.

Leaching of Carbothermic Reduced Titanium-bearing Blast Furnace Slag by Acid

The kinetics of the leaching of carbothermic reduced titanium-bearing blast furnace slag in Panzhihua Iron and Steel Company with acid system under atmosphere pressure was studied. The results show that the temperature and concentration have significant influence on leaching of carbothermic reduced titanium-bearing blast furnace slag by acid. The experimental data of leaching indicate that the shrinking core model with chemical reaction controlled process is most applicable for the acid leaching. The apparent activation energy can be estimated to be from 23 to 32 k J/mol. Furthermore, the main products are TiC and SiO_2 after leaching.

Synthesis,Characterization of NaA Zeolite from Blast Furnace Slag(BFS)via Alkaline Fusion and Hydrothermal Treatment

A blast furnace slag zeolite(BFSZ)material was successfully synthesized from BFS by alkaline fusion and hydrothermal treatment.Via the analyses of XRD,FT-IR,FE-SEM,XRF,CEC and BET surface area measurement,when zeolite was synthesized at a crystallization temperature of 100℃with initial Si/Al ratio of 1:1,the main composition in the product is Na-A zeolite.Under the above conditions,the BFSZ was synthesized with CEC of 3.06 meq/g and maximum BET surface area of 37.55 m^(2)·g^(-1).Moreover,the incorporating of BFS-derived minor metals(such as Mg,Fe,and Ca)are found to be of little importance for the synthesis of BFSZ.Thus the obtained BFSZ material has a great adsorption performance for removing Mn^(2+),Cu^(2+),and NH_(4)^(+)ions diluted in water,owing to the higher CEC.

Efficient Use of Steel Slag in Alkali-Activated Blast Furnace Slag Based Geopolymer

Energy shortage and the emission of greenhouse gases have become a global problem of urgent concern.Therefore,there is an urgent need to develop a low carbon building material.Geopolymers have become a hot topic due to their environmental sustainability and the feasibility of immobilizing industrial waste.In this paper,steel slag(SS)fines were investigated as auxiliary materials of blast furnace slag(BFS)based geopolymer.The hydration heat properties,flowability,compressive strength,sorptivity coefficient,X-ray diffraction(XRD),and scanning electron microscopy(SEM)of the geopolymer pastes were determined.The results showed that the incorporation of SS weakened the reactivity of the BFS-based geopolymer paste and improved the flow values of the paste.The compressive strength of the geopolymer with 20%SS content reached 117 MPa at 28 d.The geopolymer specimens with high compressive strength showed a low sorptivity coefficient.The microscopic results showed that the addition of the appropriate amount of SS reduced the cracks,improved the density of the geopolymer,and produced a geopolymer composite with excellent mechanical properties.

Determination of dielectric properties of titanium carbide fabricated by microwave synthesis with Ti-bearing blast furnace slag

The preparation of functional material titanium carbide by the carbothermal reduction of Ti-bearing blast furnace slag with microwave heating is an effective method for valuable metals recovery;it can alleviate the environmental pressure caused by slag stocking.The dynamic dielectric parameters of Ti-bearing blast furnace slag/pulverized coal mixture under high-temperature heating are measured by the cylindrical resonant cavity perturbation method.Combining the transient dipole and large π bond delocalization polarization phenomena, the interaction mechanism of the microwave macroscopic non-thermal effect on the titanium carbide synthesis reaction was revealed.The material thickness range during microwave heating was optimized by the joint analysis of penetration depth and reflection loss, which is of great significance to the design of the microwave reactor for the carbothermal reduction of Ti-bearing blast furnace slag.

Influence of aluminium nitride as a foaming agent on the preparation of foam glass-ceramics from high-titanium blast furnace slag

To effectively reuse high-titanium blast furnace slag （TS）, foam glass-ceramics were successfully prepared by powder sintering at 1000℃. TS and waste glass were used as the main raw materials, aluminium nitride （AIN） as the foaming agent, and borax as the fluxing agent. The influence of the amount of A1N added （lwt%-5wt%） on the crystalline phases, microstructure, and properties of the produced foam glass-ceramics was studied. The results showed that the main crystal phases were perovskite, diopside, and augite. With increasing A1N content, a transformation from diopside to augite occurred and the crystallinity of the pyroxene phases slightly decreased. Initially, the aver- age pore size and porosity of the foam glass-ceramics increased and subsequently decreased; similarly, their bulk density and compressive strength decreased and subsequently increased. The optimal properties were obtained when the foam glass-ceramics were prepared by adding 4wt% AIN.

Indirect mineral carbonation of blast furnace slag with(NH4)2SO4 as a recyclable extractant

Large quantities of COand blast furnace slag are discharged in the iron and steel industry. Mineral carbonation of blast furnace slag can offer substantial COemission reduction and comprehensive utilisation of the solid waste. In this study, a recyclable extractant,（NH）SO, was used to extract calcium and magnesium from blast furnace slag（main phases of gehlenite and akermanite） by using low-temperature roasting to fix COthrough aqueous carbonation. The process parameters and efficiency of the roasting extraction, mineralisation, and Al recovery were investigated in detail. The results showed that the extractions of Ca, Mg, and Al can reach almost 100% at an（NH4）SO-to-slag mass ratio of 3:1 and at 370°C in 1 h. Adjusting the p H value of the leaching solution of the roasted slag to 5.5 with the NHreleased during the roasting resulted in 99% Al precipitation, while co-precipitation of Mg was lower than 2%. The Mg-rich leachate after the depletion of Al and the leaching residue（main phases of CaSOand SiO） were carbonated using（NH）COand NHHCOsolutions, respectively, under mild conditions. Approximately 99% of Ca and 89% of Mg in the blast furnace slag were converted into CaCOand（NH）Mg（CO）·4 HO,respectively. The latter can be selectively decomposed to magnesium carbonate at 100-200 °C to recover the NHfor reuse. In the present route, the total COsequestration capacity per tonne of blast furnace slag reached up to 316 kg, and 313 kg of Al-rich precipitate, 1000 kg of carbonated product containing CaCOand SiO, and 304 kg of carbonated product containing calcium carbonate and magnesium carbonate were recovered simultaneously. These products can be used, respectively, as raw materials for the production of electrolytic aluminium, cement, and light magnesium carbonate to replace natural resources.

Characteristics of gaseous product from municipal solid waste gasification with hot blast furnace slag

Possibility of combustible gas production from municipal solid waste （MSW） using hot blast furnace （BF） slag has been studied.The objective of this work is to generate combustible gas from MSW using heated BF slag.In this experiment,the thermal stability of the MSW was analyzed by thermogravimetric analysis,and effects of temperature,gasifying agent （air,N2,steam） and BF slag on the gas products were investigated at 600？900 ？C.The thermogravimetric analysis indicates that the weight loss of MSW includes four stages：evaporation of the moisture,combustion of volatile materials,burning of carbon residue and burnout of ash.The contents of the combustible gas increase with increasing temperature,and the lower calorific value （LCV） increases rapidly at 600？900 ？C.It is found that volume fraction of CO,H2 and CH4 at different atmospheres increases in the order N2〈air〈steam.It is believed that BF slag acts as the catalyst and the heat carrier,which promotes the gasification reactivity of MSW.

Effect of sintering temperature on the microstructure and properties of foamed glass-ceramics prepared from high-titanium blast furnace slag and waste glass

Foamed glass-ceramics were prepared via a single-step sintering method using high-titanium blast furnace slag and waste glass as the main raw materials The influence of sintering temperature(900–1060℃) on the microstructure and properties of foamed glass-ceramics was studied. The results show that the crystal shape changed from grainy to rod-shaped and finally turned to multiple shapes as the sintering temperature was increased from 900 to 1060℃. With increasing sintering temperature, the average pore size of the foamed glass-ceramics increased and subsequently decreased. By contrast, the compressive strength and the bulk density decreased and subsequently increased. An excessively high temperature, however, induced the coalescence of pores and decreased the compressive strength. The optimal properties, including the highest compressive strength(16.64 MPa) among the investigated samples and a relatively low bulk density(0.83 g/cm^3), were attained in the case of the foamed glass-ceramics sintered at 1000℃.

Status and development of mineral wool made from molten blast furnace slag

This study describes the characteristics of mineral wool and its applications,and also introduces the traditional process of mineral wool made from molten blast furnace （BF） slag. Compared with high energy consumption of the traditional process,the production of mineral wool by using molten BF slag will be able to take full advantage of the sensible heat of molten slag, and also reduce production costs. However, there are also further issues to resolve such as how to obtain the required amount of molten BF slag and how to make it homogeneous. Based on the physical and chemical properties of the molten BF slag,the investigation into the relationship between temperature and viscosity under different acidity coefficients of the slag and silicon mixture was conducted. Combined with the crystallization and phase diagram of slag wool, its heat resistance, water resistance, durability and corrosion resistance were analyzed. Finally, trends of the technology development are proposed.

Influence of CeO_2 addition on the preparation of foamed glass-ceramics from high-titanium blast furnace slag

Foamed glass-ceramics doped with cerium oxide（CeO_2）were successfully prepared from high-titanium blast furnace slag by one-step sintering.The influence of CeO_2 addition（1.5wt%–3.5wt%）on the crystalline phases,microstructure,and properties of foamed glass-ceramics was studied.Results show that CeO_2 improves the stability of the glass phase and changes the two-dimensional crystallization mechanism into three-dimensional one.XRD analysis indicates the presence of Ca（Mg,Fe）Si_2O_6 and Ca（Ti,Mg,Al）（Si,Al）_2O_（6 ）in all sintered samples.Added with CeO_2,Ti CeO_4 precipitates,and crystallinity increases,leading to increased thickness of pore walls and uniform pores.The comprehensive properties of foamed glass-ceramics are better than that of samples without CeO_2.In particular,the sample added with a suitable amount of CeO_2（2.5wt%）exhibits bulk density that is similar to and compressive strength（14.9 MPa）that is more than twice of foamed glass-ceramics without CeO_2.