Two-stage dynamic recrystallization and texture evolution in Al-7Mg alloy during hot torsion

Hot torsion tests were performed on the Al-7Mg alloy at the temperature ranging from 300 to 500℃ and strain rates between 0.05 and 5 s^(-1) to explore the progressive dynamic recrystallization(DRX)and texture behaviors.The DRX behavior of the alloy manifested two distinct stages:Stage 1 at strain of≤2 and Stage 2 at strains of≥2.In Stage 1,there was a slight increase in the DRXed grain fraction(X_(DRX))with predominance of discontinuous DRX(DDRX),followed by a modest change in X_(DRX) until the transition to Stage 2.Stage 2 was marked by an accelerated rate of DRX,culminating in a substantial final X_(DRX) of~0.9.Electron backscattered diffraction(EBSD)analysis on a sample in Stage 2 revealed that continuous DRX(CDRX)predominantly occurred within the(121)[001]grains,whereas the(111)[110]grains underwent a geometric DRX(GDRX)evolution without a noticeable sub-grain structure.Furthermore,a modified Avrami’s DRX kinetics model was utilized to predict the microstructural refinement in the Al-7Mg alloy during the DRX evolution.Although this kinetics model did not accurately capture the DDRX behavior in Stage 1,it effectively simulated the DRX rate in Stage 2.The texture index was employed to assess the evolution of the texture isotropy during hot-torsion test,demonstrating significant improvement(>75%)in texture randomness before the commencement of Stage 2.This initial texture evolution is attributed to the rotation of parent grains and the substructure evolution,rather than to an increase in X_(DRX).

Mechanical response joint under of the TiAl/steel brazed torsional load

An attempt to investigate the mechanical response to the torsional load, torsional tests of TiA1/steel brazed joints were conducted at room temperature. The TiAl/steel joints used in the torsional loading tests were brazed under the optimum parameters of 1 173 K and 300 s. Torsional strength, fracture path and the behavior of the reaction phases were studied. The results show that the average torsional strength of the joints with the diameters of 13mm, 16 mm and 20 mm is 136 N · m, 270 N · m and 490 N · m, respectively; which is 81.9% , 85.5% and 86. 2% of the TiAl base metal, respectively. Fracture path and crack propagation process analysis shows, when subjected to the torsional load, Ag-based solid solution is deformed and cracks germinate at the interface of Ag-based solid solutioa/AlCu2 Ti particles or Ag-based solid solution/AlCu2 Ti layers, grow up and propagate into the Al-Cu- Ti brittle reaction layers, then propagate into the TiAl base metal, subsequently result in failure.

Stiffness Degradation of Undisturbed Saturated Soft Clay in the Yangtze Estuary Under Complex Stress Conditions

Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on the saturated soft marine clay in the Yangtze Estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotropic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases （or degradation degree increases） significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared with the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does.Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.

MECHANICAL BEHAVIORS OF SATURATED SAND UNDER COMPLICATED LOADING

The different physical states of saturated sand, including shear elasticity, positive dilatancy, and negative dilatancy (preliminary negative dilatancy, secondary negative dilatancy and reversal negative dilatancy) are revealed based on the pore water pressure response of saturated sand in undrained dynamic torsional tests of thin cylinder samples and also checked by the drained cyclic triaxial tests under a given mean effective normal stress. According to the effective stress path of different physical states under the undrained cyclic torsional tests the physical state transformation surface, stress history boundary and yield surface are determined, and the state boundary surface is also determined by the range of effective frictional stress state movement. Based on the moving yield surface without rotation, and the expanding stress history boundary surface relevant to the stress path variations under different physical states in 3D stress space, a physical state model is proposed to provide a new approach to calculating the transient pore water pressure under the undrained condition, and the volume strain of dilatation under drained condition in this paper.

Effects of humidity on shear behavior of bamboo

Bamboo is a naturally occurring biological composite, however its microstructure and hence its properties are very complex compared to the manmade composites. Due to optimization, it can be assumed that the variation in properties along the thickness of the culm be a smooth transition for better bonding strength between layers and to prevent non uniformity in stress concentration. As a consequence, biological structures are complicated and functionally graded. Hence, a realistic model that can capture the mechanical performance of bamboo is valuable in future design of robust multifunctional composites. This paper presents the results of experimental and numerical studies on the torsional （shear） properties of bamboo. The hierarchical and multi-scale structure of bamboo and the distribution of micro-scale fibers are revealed via laser scanning and atomic force microscopy. This information was incorporated into a finite element model to analyze the mechanical behavior of bamboo under torsion and to estimate the shear modulus of bamboo along the fibers. Moreover, the effects of humidity and therefore water content on the mechanical properties of bamboo were evaluated by performing torsion tests on samples maintained in environments with different humidities. Increasing the humidity does not cause a drop in the shear modulus, however, a jump in the shear modulus did occur at around 60% humidity. Results of this study indicate that the highest strength values in samples occurred in environments with humidity levels between 60% and 80% and undergo a significant drop after that. In higher humidities, the samples behave more ductile.

Formulation of cross-anisotropic failure criterion for soils

Inherently anisotropic soil fabric has a considerable influence on soil strength. To model this kind of inherent anisotropy, a three-dimensional anisotropic failure criterion was proposed, employing a scalar-valued anisotropic variable and a modified general three- dimensional isotropic failure criterion. The scalar-valued anisotropic variable in all sectors of the deviatoric plane was defined by correlating a normalized stress tensor with a normalized fabric tensor. Detailed comparison between the available experimental data and the corresponding model predictions in the deviatoric plane was conducted. The proposed failure criterion was shown to well predict the failure behavior in all sectors, especially in sector II with the Lode angle ranging between 60° and 120°, where the prediction was almost in accordance with test data. However, it was also observed that the proposed criterion overestimated the strength of dense Santa Monica Beach sand in sector III where the intermediate principal stress ratio b varied from approximately 0.2 to 0.8, and slightly underestimated the strength when b was between approximately 0.8 and 1. The difference between the model predictions and experimental data was due to the occurrence of shear bending, which might reduce the measured strength. Therefore, the proposed anisotropic failure criterion has a strong ability to characterize the failure behavior of various soils and potentially allows a better description of the influence of the loading direction with respect to the soil fabric.

Influence of Specimen Geometry of Hot Torsion Test on Temperature Distribution During Reheating Treatment of API-X70

The commercial finite element package ANSYSTM was utilized for prediction of temperature distribution during reheating treatment of hot torsion test （HTT） samples with different geometries for API-X70 microalloyed steel. Simulation results show that an inappropriate choice of test specimen geometry and reheating conditions before deformation could lead to non-uniform temperature distribution within the gauge section of specimen. Therefore, assumptions of isothermal experimental conditions and zero temperature gradient within the specimen cross section appear unjustified and led to uncertainties of flow curve obtained. Recommendations on finding proper specimen geometry for reducing temperature gradient along the gauge part of specimen will be given to create homogeneous initial microstructure as much as possible before deformation in order to avoid uncertainty in consequent results of HTT.

Warm Deformation Microstructure of a Plain Carbon Steel

Grain refinement in a plain carbon steel under intercritical warm deformation was studied by torsion tes ring. Based on the experimental results, the warm flow behaviour and microstructural evolution of ferrite were researched with particular emphasis on the effect of the strain rate in controlling the grain refinement mechanism of fer- rite. The deformed microstructures were investigated at various strain rates using optical microscopy and electron back-scattered diffraction （EBSD）. The EBSD observations indicate that an increase in the strain rate leads to the development of new fine ferrite grains with high angle boundaries. Furthermore, it shows that the annihilation of dislo- cations occurs more readily at lower strain rate. The elongated ferrite grains continuously dynamically recrystallize to form the equiaxed fine ferrite grains. Thereby, the aspect ratio of elongated grains decreases with increasing the strain rate. Furthermore, the peak stress and steady state stress of ferrite both increase with increasing strain rate. Based on the study, the effect of strain rate on the development of fine ferrite grains during continuous dynamic recrystallization of ferrite was analyzed in detail.