Double-layered graphene sheets （DLGSs） can be applied to the development of a new generation of nanomechanical sensors due to their unique physical properties. A rectangular DLGS with a nanoparticle randomly located...Double-layered graphene sheets （DLGSs） can be applied to the development of a new generation of nanomechanical sensors due to their unique physical properties. A rectangular DLGS with a nanoparticle randomly located in the upper sheet is modeled as two nonlocal Kirchhoff plates connected by van der Waals forces. The Galerkin strip transfer function method which is a semi-analytical method is developed to compute the natural frequencies of the mass- plate vibrating system. It can give exact closed-form solutions along the longitudinal direction of the strip. The results obtained from the semi-analytical method are compared with the previous ones, and the differences between the single-layered graphene sheet （SLGS） and the DLGS mass sensors are also investigated. The results demonstrate the similarity of the in-phase mode between the SLGS and DLGS mass sensors. The sensitivity of the DLGS mass sensor can be increased by decreasing the nonlocal parameter, moving the attached nanoparticle closer to the DLGS center and making the DLGS smaller. These conclusions are helpful for the design and application of graphene-sheet-based resonators as nano-mass sensors.展开更多
Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the...Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the existing known information is used to infer the unknown information's character, state and development trend in a fault pattern, and to make possible forecasting and decisions for future development. It involves the whitenization of a Grey process. But the traditional equal time interval Grey GM (1,1) model requires equal interval data and needs to bring about accumulating addition generation and reversion calculations. Its calculation is very complex. However, the non equal interval Grey GM (1,1) model decreases the condition of the primitive data when establishing a model, but its requirement is still higher and the data were pre processed. The abrasion primitive data of plant could not always satisfy these modeling requirements. Therefore, it establishes a division method suited for general data modeling and estimating parameters of GM (1,1), the standard error coefficient that was applied to judge accuracy height of the model was put forward; further, the function transform to forecast plant abrasion trend and assess GM (1,1) parameter was established. These two models need not pre process the primitive data. It is not only suited for equal interval data modeling, but also for non equal interval data modeling. Its calculation is simple and convenient to use. The oil spectrum analysis acted as an example. The two GM (1,1) models put forward in this paper and the new information model and its comprehensive usage were investigated. The example shows that the two models are simple and practical, and worth expanding and applying in plant fault diagnosis.展开更多
The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic gr...The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic ground condition. This approach is a direct hit to the atmospheric scattering OTF using the same original context of modulation transfer function （MTF） measurement, i.e., images of sinusoidal grating at different spatial frequencies. Both the amplitude and phase shift of the OTF at various zenith and azimuth angles can be obtained at an arbitrary spatial frequency.展开更多
In this paper the definitions of generalized transfer functios of control system and itscontinuity are presented.Using generalized transfer function as a tool,a set of theorems fordeciding movement stability have been...In this paper the definitions of generalized transfer functios of control system and itscontinuity are presented.Using generalized transfer function as a tool,a set of theorems fordeciding movement stability have been constructed.Thus basing understanding of thecharacteristics of a control dynamics system on its measured procedure will simplify thedecision method of movement stability problems.展开更多
The key difficulty of restoring a fuzzy image is to estimate its point spread function( PSF). In the paper,PSF is modelled based on modulation transfer function( MTF). The first step is calculating the image MTF. In t...The key difficulty of restoring a fuzzy image is to estimate its point spread function( PSF). In the paper,PSF is modelled based on modulation transfer function( MTF). The first step is calculating the image MTF. In the traditional slanted-edge method,a sub-block is always manually extracted from original image and its MTF will be viewed as the result of the whole image. However,handcraft extraction is inefficient and will lead to inaccurate results. Given this,an automatic MTF computation algorithm is proposed,which extracts and screens out all the effective sub-blocks and calculates their average MTF as the final result. Then,a two-dimensional MTF restoration model is constructed by multiplying the horizontal and vertical MTF,and it is combined with conventional image restoration methods to restore fuzzy image. Experimental results indicate the proposed method implementes a fast and accurate MTF computation and the MTF model improves the performance of conventional restoration methods significantly.展开更多
Applying 3-dimension finite difference method, the distribution characteristics of horizontal field transfer functions for rectangular conductor have been computed, and the law of distribution for Re-part and Im-part ...Applying 3-dimension finite difference method, the distribution characteristics of horizontal field transfer functions for rectangular conductor have been computed, and the law of distribution for Re-part and Im-part has been given. The influences of source field period, the conductivity, the buried depth and the length of the conductor on the transfer functions were studied. The extrema of transfer functions appear at the center, the four corners and around the edges of conductor, and move with the edges. This feature demonstrates that around the edges are best places for transfer functions' observation.展开更多
强耦合条件下,复杂系统的有限元分析受到自由度的影响计算成本高昂。虽然模态叠加技术能减少耦合系统的自由度,但基于忽略不同子系统间高阶模态和低阶模态耦合作用的假设,若使用非耦合模态可能导致收敛性差。基于无阻尼声振耦合方程,本...强耦合条件下,复杂系统的有限元分析受到自由度的影响计算成本高昂。虽然模态叠加技术能减少耦合系统的自由度,但基于忽略不同子系统间高阶模态和低阶模态耦合作用的假设,若使用非耦合模态可能导致收敛性差。基于无阻尼声振耦合方程,本文采用分片传递函数法(Patch transfer function method,PTFM)将耦合面处理成一系列独立的分片,每个分片上所属单元节点值的平均值定义为分片传递函数,通过使用连续性关系计算耦合系统的分片传递函数。将耦合矩阵的求逆简化为源点到响应点的传递函数,可以快速计算耦合系统响应值。分别利用直接耦合法(Direct coupling method,DCM)和分片传递函数法计算板和空气声腔耦合模型,验证分片传递函数法的有效性,并讨论了分片传递函数的算法原理和计算误差。展开更多
The Vector Hydrophone(VH) is widely used to remotely detect underwater targets. Accurately measuring the self-noise of the VH provides an important basis for evaluating the performance of the detection system in which...The Vector Hydrophone(VH) is widely used to remotely detect underwater targets. Accurately measuring the self-noise of the VH provides an important basis for evaluating the performance of the detection system in which it is utilized, since the ability to acquire weak signals is determined by the VH self-noise level. To accurately measure the VH self-noise level in actual working conditions, the Dual-channel Transfer Function Method(DTFM) is proposed to reduce ambient background noise interference. In this paper, the underlying principles of DTFM in reducing ambient background noise is analyzed. The numerical simulations to determine the influence of ambient background noise, and the sensitivity difference of the two VHs on the measurement results are studied. The results of measuring the VH self-noise level in a small laboratory water tank by using DTMF indicate that ambient background noise interference can be reduced effectively by employing DTMF, more accurate self-noise level can be obtained as well. The DTMF provides an effective method for accurately measuring the self-noise level of VHs and also provides technical support for the practical application of the VH in underwater acoustics.展开更多
The electronic and physical properties of PtmPdn （m＋n≤5） metal clusters and their interactions with dioxygen have been studied by using hybrid density functional B3LYP method. The total energies, atomization energ...The electronic and physical properties of PtmPdn （m＋n≤5） metal clusters and their interactions with dioxygen have been studied by using hybrid density functional B3LYP method. The total energies, atomization energies, vibration frequencies, and charge distributions were reported. The Pt-Pt bridge site modified by Pd atoms was found to be the most active site for the dissociation of dioxygen, which was mainly due to the change of electronic structures of the Pt atoms in bimetallic Pt-Pd clusters.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.11302254)
文摘Double-layered graphene sheets （DLGSs） can be applied to the development of a new generation of nanomechanical sensors due to their unique physical properties. A rectangular DLGS with a nanoparticle randomly located in the upper sheet is modeled as two nonlocal Kirchhoff plates connected by van der Waals forces. The Galerkin strip transfer function method which is a semi-analytical method is developed to compute the natural frequencies of the mass- plate vibrating system. It can give exact closed-form solutions along the longitudinal direction of the strip. The results obtained from the semi-analytical method are compared with the previous ones, and the differences between the single-layered graphene sheet （SLGS） and the DLGS mass sensors are also investigated. The results demonstrate the similarity of the in-phase mode between the SLGS and DLGS mass sensors. The sensitivity of the DLGS mass sensor can be increased by decreasing the nonlocal parameter, moving the attached nanoparticle closer to the DLGS center and making the DLGS smaller. These conclusions are helpful for the design and application of graphene-sheet-based resonators as nano-mass sensors.
文摘Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the existing known information is used to infer the unknown information's character, state and development trend in a fault pattern, and to make possible forecasting and decisions for future development. It involves the whitenization of a Grey process. But the traditional equal time interval Grey GM (1,1) model requires equal interval data and needs to bring about accumulating addition generation and reversion calculations. Its calculation is very complex. However, the non equal interval Grey GM (1,1) model decreases the condition of the primitive data when establishing a model, but its requirement is still higher and the data were pre processed. The abrasion primitive data of plant could not always satisfy these modeling requirements. Therefore, it establishes a division method suited for general data modeling and estimating parameters of GM (1,1), the standard error coefficient that was applied to judge accuracy height of the model was put forward; further, the function transform to forecast plant abrasion trend and assess GM (1,1) parameter was established. These two models need not pre process the primitive data. It is not only suited for equal interval data modeling, but also for non equal interval data modeling. Its calculation is simple and convenient to use. The oil spectrum analysis acted as an example. The two GM (1,1) models put forward in this paper and the new information model and its comprehensive usage were investigated. The example shows that the two models are simple and practical, and worth expanding and applying in plant fault diagnosis.
基金supported by the Main Direction Program of Knowledge Innovation of Chinese Academy of Sciences(Grant No.KGFZD-125-13-006)
文摘The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic ground condition. This approach is a direct hit to the atmospheric scattering OTF using the same original context of modulation transfer function （MTF） measurement, i.e., images of sinusoidal grating at different spatial frequencies. Both the amplitude and phase shift of the OTF at various zenith and azimuth angles can be obtained at an arbitrary spatial frequency.
文摘In this paper the definitions of generalized transfer functios of control system and itscontinuity are presented.Using generalized transfer function as a tool,a set of theorems fordeciding movement stability have been constructed.Thus basing understanding of thecharacteristics of a control dynamics system on its measured procedure will simplify thedecision method of movement stability problems.
基金Supported by the National High Technology Research and Development Programme of China(No.2012AA12A305)the National Key Technology R&D Program of the Ministry of Science and Technology(No.2013BAH03B01)+1 种基金Fundamental Research Funds for the Central Universities of China(No.2042015kf0059)China Postdoctoral Science Foundation(No.2015M582277)
文摘The key difficulty of restoring a fuzzy image is to estimate its point spread function( PSF). In the paper,PSF is modelled based on modulation transfer function( MTF). The first step is calculating the image MTF. In the traditional slanted-edge method,a sub-block is always manually extracted from original image and its MTF will be viewed as the result of the whole image. However,handcraft extraction is inefficient and will lead to inaccurate results. Given this,an automatic MTF computation algorithm is proposed,which extracts and screens out all the effective sub-blocks and calculates their average MTF as the final result. Then,a two-dimensional MTF restoration model is constructed by multiplying the horizontal and vertical MTF,and it is combined with conventional image restoration methods to restore fuzzy image. Experimental results indicate the proposed method implementes a fast and accurate MTF computation and the MTF model improves the performance of conventional restoration methods significantly.
文摘Applying 3-dimension finite difference method, the distribution characteristics of horizontal field transfer functions for rectangular conductor have been computed, and the law of distribution for Re-part and Im-part has been given. The influences of source field period, the conductivity, the buried depth and the length of the conductor on the transfer functions were studied. The extrema of transfer functions appear at the center, the four corners and around the edges of conductor, and move with the edges. This feature demonstrates that around the edges are best places for transfer functions' observation.
文摘强耦合条件下,复杂系统的有限元分析受到自由度的影响计算成本高昂。虽然模态叠加技术能减少耦合系统的自由度,但基于忽略不同子系统间高阶模态和低阶模态耦合作用的假设,若使用非耦合模态可能导致收敛性差。基于无阻尼声振耦合方程,本文采用分片传递函数法(Patch transfer function method,PTFM)将耦合面处理成一系列独立的分片,每个分片上所属单元节点值的平均值定义为分片传递函数,通过使用连续性关系计算耦合系统的分片传递函数。将耦合矩阵的求逆简化为源点到响应点的传递函数,可以快速计算耦合系统响应值。分别利用直接耦合法(Direct coupling method,DCM)和分片传递函数法计算板和空气声腔耦合模型,验证分片传递函数法的有效性,并讨论了分片传递函数的算法原理和计算误差。
文摘The Vector Hydrophone(VH) is widely used to remotely detect underwater targets. Accurately measuring the self-noise of the VH provides an important basis for evaluating the performance of the detection system in which it is utilized, since the ability to acquire weak signals is determined by the VH self-noise level. To accurately measure the VH self-noise level in actual working conditions, the Dual-channel Transfer Function Method(DTFM) is proposed to reduce ambient background noise interference. In this paper, the underlying principles of DTFM in reducing ambient background noise is analyzed. The numerical simulations to determine the influence of ambient background noise, and the sensitivity difference of the two VHs on the measurement results are studied. The results of measuring the VH self-noise level in a small laboratory water tank by using DTMF indicate that ambient background noise interference can be reduced effectively by employing DTMF, more accurate self-noise level can be obtained as well. The DTMF provides an effective method for accurately measuring the self-noise level of VHs and also provides technical support for the practical application of the VH in underwater acoustics.
基金This work was partly supported by Innovation Foundation of the Chinese Academy of Sciences (K2003D2), National Natural Science Foundation of China (No. 20173060), Hi-tech Research and Development Program of China (2003AA517040) and Knowledge Innovation Program of the Chinese Academy of Sciences (KGCX2-SW-310)
文摘The electronic and physical properties of PtmPdn （m＋n≤5） metal clusters and their interactions with dioxygen have been studied by using hybrid density functional B3LYP method. The total energies, atomization energies, vibration frequencies, and charge distributions were reported. The Pt-Pt bridge site modified by Pd atoms was found to be the most active site for the dissociation of dioxygen, which was mainly due to the change of electronic structures of the Pt atoms in bimetallic Pt-Pd clusters.
