Thermal Conductivity and Heat Transfer Coefficient of Concrete

A very simple model for predicting thermal conductivity based on its definiensis was presented. The thermal conductivity obtained using the model provided a good coincidence to the investigations performed by other authors. The heat transfer coefficient was determined by inverse analysis using the temperature measurements. From experimental results, it is noted that heat transfer coefficient increases with the increase of wind velocity and relative humidity, a prediction equation on heat transfer coefficient about wind velocity and relative humidity is given.

Determination of interfacial heat transfer coefficient and its application in high pressure die casting process

In this paper,the research progress of the interfacial heat transfer in high pressure die casting(HPDC)is reviewed.Results including determination of the interfacial heat transfer coefficient(IHTC),influence of casting thickness,process parameters and casting alloys on the IHTC are summarized and discussed.A thermal boundary condition model was developed based on the two correlations:(a)IHTC and casting solid fraction and(b)IHTC peak value and initial die surface temperature.The boundary model was then applied during the determination of the temperature field in HPDC and excellent agreement was found.

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR)including the gas holdup,volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature,pH and superficial gas velocity.The reactor diameter and height were 11 and 30 cm,respectively.It was equipped with a single sparger,operating at atmospheric pressure,20 and 40℃,and two pH values of 3 and 6.The height of the liquid was 23 cm,while the superficial gas velocity changed within 0.010-0.040 m·s^(-1)range.Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase.The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution.The gas holdup was calculated based on the liquid height change,while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD)in different superficial gas velocities.The results indicated that at the same temperature but different pH,the gas holdup variation was negligible,while the liquid-side volumetric mass transfer coefficient at the pH value of 6 was higher than that at the pH=3.At a constant pH but different temperatures,the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃were higher than that of the same at 20℃.A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla)in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.

Establishment and Application of UFC-ACC Heat Transfer Coefficient Model

Based on medium plate runout table ultra-fast cooling( UFC)-accelerated cooling equipment( ACC) system,a heat transfer coefficient model was constructed. Firstly,according to the measured data,heat transfer coefficients under different roll speed and water volume were calculated by using an inverse heat conduction method. Secondly,a monofactorial heat transfer coefficient calculation formula was obtained. Finally,the heat transfer coefficient model based on medium plate runout table UFC-ACC system was constructed by intercept function,slope function,interaction influence function and linear or nonlinear influencing factors. The precision of these models was validated by comparing model prediction value with measured data,and the results were in good agreement with practical needs,and the average deviation was less than 5%.

Mass transfer coefficient in the eductor liquid-liquid extraction column

In this research gasoil desalting was investigated from mass transfer point of view in an eductor liquid–liquid extraction column(eductor-LLE device).Mass transfer characteristics of the eductor-LLE device were evaluated and an empirical correlation was obtained by dimensional analysis of the dispersed phase Sherwood number.The Results showed that the overall mass transfer coefficient of the dispersed phase and extraction efficiency have been increased by increasing Sauter mean diameter(SMD)and decreasing the nozzle diameter from 2 to 1 mm,respectively.The effects of Reynolds number(R_(e)),projection ratio(ratio of the distance between venturi throat and nozzle tip to venturi throat diameter,Rpr),venturi throat area to nozzle area ratio(R_(th-n))and two phases flow rates ratio(R_(Q))on the mass transfer coefficient(K)were determined.According to the results,K increase with increasing Re and RQ and also with decreasing Rpr and R_(th-n).Semi-empirical models of drop formation,rising and coalescence were compared with our proposed empirical model.It was revealed that the present model provided a relatively good fitting for the mass transfer model of drop coalescence.Moreover,experimental data were in better agreement with calculated data with AARE value of 0.085.

Optimal Experiment Design for the Identification of the Interfacial Heat Transfer Coefficient in Sand Casting

The interfacial heat transfer coefficient(IHTC)is one of the main input parameters required by casting simulation software.It plays an important role in the accurate modeling of the solidification process.However,its value is not easily identifiable by means of experimental methods requiring temperature measurements during the solidification process itself.For these reasons,an optimal experiment design was performed in this study to determine the optimal position for the temperature measurement and the optimal thickness of the rectangular cast iron part.This parameter was identified using an inverse technique.In particular,two different algorithms were used:Levenberg Marquard(LM)and Monte Carlo(MC).A numerical model of the solidification process was associated with the optimization algorithm.The temperature was measured at different positions from the mould/metal interface at d=0 mm(mould/metal interface),30 mm,60 mm and 90 mm.the thicknesses of the cast part were:L1=40 mm,60 mm and 80 mm.A comparative study on the IHTC identification was then carried out by varying the initial value of the IHTC between 500 Wm^(-2)K^(-1) and 1050 Wm^(-2)K^(-1).Results showed that the MC algorithm used for estimating the IHTC gives the best results,and the optimal position was at d=30 mm,the position closest to the mould/metal interface,for the lowest thickness L1=40 mm.

VOLUMETRIC MASS TRANSFER COEFFICIENT BETWEEN SLAG AND METAL IN COMBINED BLOWING CONVERTER

The effects of operation parameters of combined blowing converter on the volumetric mass transfer coefficient between slag and steel are studied with a cold model with water simulating steel, oil simulating slag and benzoic acid as the transferred substance between water and oil. The results show that, with lance level of 2.1m and the top blowing rate of 25000Nm3/h, the volumetric mass transfer coefficient changes most significantly when the bottom blowing rate ranges from 384 to 540Nm3/h. The volumetric mass transfer coefficient reaches its maximum when the lance level is 2.1m, the top blowing rates is 30000Nm3/h, and the bottom blowing rate is 384Nm3/h with tuyeres located symmetrically at 0.66D of the converter bottom.

Effect Analysis of Volume Fraction of Nanofluid Al2O3-Water on Natural Convection Heat Transfer Coefficient in Small Modular Reactor

Development and use of nuclear energy is currently growing very rapidly, in order to achieve increasingly advanced technology, both in terms of design, economic factors and safety factors. Thermal-hydraulics aspects of nuclear reactors should be done with calculation and near-perfect condition. Including today began development of a nuclear reactor with low power below 300 MW, or commonly called the Small Modular Reactor (SMR). One is CAREM-25 developed by Argentina with a power of 25 MW, where in CAREM already using natural circulation system and the use of nanofluid as coolant fluid. In this research, analytic modeling of thermal-hydraulics nuclear reactor SMR CAREM-25, when the nanofluid Al2O3-Water used as cooling fluid in the cooling system of a nuclear reactor. Further to this analytic modeling will be done on CFD. Analytic modeling with CFD to determine the flow phenomena and distribution as well as the effect of nano-particles of Al2O3-Water based on the volume fraction (1% and 3%) of the coefficient of heat transfer by natural convection.

A convenient method for measuring gas-liquid volumetric mass transfer coefficient in micro reactors

The research on gas-liquid multiphase reactions using micro reactors is becoming increasingly widespread, given their excellent mass transfer performance. Establishing an accurate and reliable method to measure the gas-liquid mass transfer performance of micro reactors is crucial for evaluating and optimizing the design of micro reactor structure. In this paper, the physical absorption method of aqueous solution-CO_(2) and the chemical absorption method of sodium carbonate solution-CO_(2) were proposed. By analyzing the chemical reaction equilibrium during the absorption process, the relationship between the mass transfer of CO_(2) and the solubility of hydroxide ions in the solution was established, and the total gas-liquid mass transfer coefficient was immediately obtained by measuring the p H value. The corresponding testing platform and process have been established based on the characteristics of the proposed method to ensure fast and accurate measurement. In addition, the chemical absorption method takes into account temperature factors that were not previously considered. The volumetric mass transfer coefficient measured by these two methods is in the same range as those measured by other methods using the same microchannel structure in previous literature. The methods have the advantages of low equipment cost, faster measurement speed, and simpler procedures, which can facilitate its wide application to the evaluation of the mass transfer performance and hence can guide the structure optimization of microchannel reactors.

Effect of surfactant frequently used in soil flushing on oxygen mass transfer in micro-nano-bubble aeration system

In-site soil flushing and aeration are the typical synergetic remediation technology for contaminated sites.The surfactant present in flushing solutions is bound to affect the aeration efficiency.The purpose of this study is to evaluate the effect of surfactant frequently used in soil flushing on the oxygen mass transfer in micro-nano-bubble(MNB)aeration system.Firstly,bio-surfactants and chemical surfactants were used to investigate their effects on Sauter mean diameter of bubble(dBS),gas holdup(ε),volumetric mass-transfer coefficient(kLa)and liquid-side mass-transfer coefficient(kL)in the MNB aeration system.Then,based upon the experimental results,the Sardeing's and Frossling's models were modified to describe the effect of surfactant on kL in the MNB aeration.The results showed that,for the twenty aqueous surfactant solutions,with the increase in surfactant concentration,the value of dBS,kLa and kL decreased,while the value ofεand gas-liquid interfacial area(a)increased.These phenomena were mainly attributed to the synergistic effects of immobile bubble surface and the suppression of coalescence in the surfactant solutions.In addition,with the presence of electric charge,MNBs in anionic surfactant solutions were smaller and higher in number than in non-ionic surfactant solutions.Furthermore,the accumulation of surfactant on the gas-liquid interface was more conspicuous for small MNB,so the reduction of kL in anionic surfactant solutions was larger than that in non-ionic surfactant solutions.Besides,the modified Frossling's model predicted the effect of surfactant on kL in MNB aeration system with reasonable accuracy.

Improving Heat Transfer in Parabolic Trough Solar Collectors by Magnetic Nanofluids

A parabolic trough solar collector(PTSC)converts solar radiation into thermal energy.However,low thermal efficiency of PTSC poses a hindrance to the deployment of solar thermal power plants.Thermal performance of PTSC is enhanced in this study by incorporating magnetic nanoparticles into the working fluid.The circular receiver pipe,with dimensions of 66 mm diameter,2 mm thickness,and 24 m length,is exposed to uniform temperature and velocity conditions.The working fluid,Therminol-66,is supplemented with Fe3O4 magnetic nanoparticles at concentrations ranging from 1%to 4%.The findings demonstrate that the inclusion of nanoparticles increases the convective heat transfer coefficient(HTC)of the PTSC,with higher nanoparticle volume fractions leading to greater heat transfer but increased pressure drop.The thermal enhancement factor(TEF)of the PTSC is positively affected by the volume fraction of nanoparticles,both with and without a magnetic field.Notably,the scenario with a 4%nanoparticle volume fraction and a magnetic field strength of 250 G exhibits the highest TEF,indicating superior thermal performance.These findings offer potential avenues for improving the efficiency of PTSCs in solar thermal plants by introducing magnetic nanoparticles into the working fluid.

Effect of Rare Earths on Diffusion Coefficient and Transfer Coefficient of Carbon during Carburizing

The diffusion coefficient of carbon in surface layer of steel-20 rare earth carburixed at 880 degreesC and 900 degreesC for 8 h was calculated by substituting the measured layer depths into the diffusion equation. The mathematical model of the transfer coefficient of carbon was deduced based on the kinetics of weight gain during gas carburizing. The calculated results show that the main reason why the gas carburizing process is accelerated is due to the obvious increase in the diffusion coefficient and transfer coefficient of carbon resulted from the addition of RE.

Landslide Reliability Analysis Based on Transfer Coefficient Method: A Case Study from Three Gorges Reservoir

To evaluate the reliability of a landslide in a reservoir, the universal transfer coefficient method, which is popularized by the Chinese standard, is adopted as performance function in this study for： （1） common deterministic method stability evaluation; （2） reliability evaluation based on a Monte Carlo method; （3） comparison of landslide reliability under different water levels and under different correlation coefficients between soil shear strength parameters （c, Φ）, respectively with mean, standard deviation, reliability coefficient and failure probability. This article uses the Bazimen （八字门） landslide, which is located at the outlet of Xiangxi （香溪） River in the Three Gorges Reservoir, as an example to evaluate its stability and reliability under different water levels with two-dimensional deterministic and probabilistic methods. With the assumption that constant mean and normal distributed shear strength parameters （c, Φ）, correlation coefficient c, Φ=-1 based reliability analysis, compared with c, Φ=0 and 1, indicates obviously more increase of reliability index and lower standard deviation as water levels rise. To the case of a certain water level, c, Φ=-1 does not have constantly positive or negative effects on landslide reliability compared with c, Φ=0 or 1, but is associated with water level. Whereas the safety factor Fs by deterministic method, which is almost the same value as corresponding mean of safety factor from probabilistic analysis, will increase slightly as water level increases.

Forced Convection Heat Transfer in Porous Structure: Effect of Morphology on Pressure Drop and Heat Transfer Coefficient

A light-weight structure with sufficient mechanical strength and heat transfer performance is increasingly required for some thermal management issues.The porous structure with the skeleton supporting the ambient stress and the pores holding the flowing fluid is considered very promising,attracting significant scientific and industrial interest over the past few decades.However,due to complicated morphology of the porous matrices and thereby various performance of the pressure drop and heat transfer coefficients (HTC),the comprehensive comparison and evaluation between different structures are largely unclear.In this work,recent researches on the efforts of forced convection heat transfer in light-weight porous structure are reviewed;special interest is placed in the open-cell foam,lattice-frame,structured packed bed,and wire-woven structures.Their experimental apparatus,morphological of the porous structures,effect of morphology on pressure drop and HTC,and further applications are discussed.The new method which measure morphology accurately should be paid more attention to develop more accuracy correlation.Also,the most research focused on low Reynolds number and existing structure,while very few researchers investigated the property of forced convection heat transfer in high velocity region and developed new porous structure.

Experimental study of heat transfer coefficient with rectangular baffle fin of solar air heater

This paper presents an experimental analysis of a single pass solar air collector with, and without using baffle fin. The heat transfer coefficient between the absorber plate and air can be considerably increased by using artificial roughness on the bottom plate and under the absorber plate of a solar air heater duct. An experimental study has been conducted to investigate the effect of roughness and operating parameters on heat transfer. The investigation has covered the range of Reynolds number Re from 1259 to 2517 depending on types of the configuration of the solar collectors. Based on the experimental data, values of Nusselt number Nu have been determined for different values of configurations and operating parameters. To determine the enhancement in heat transfer and increment in thermal efficiency, the values of Nusselt have been smooth duct under similar flow compared with those of conditions.

Grain Size Distribution and Interfacial Heat Transfer Coefficient during Solidification of Magnesium Alloys Using High Pressure Die Casting Process

The objective of this study is to predict grain size and heat transfer coefficient at the metal-die interface during high pressure die casting process and solidification of the magnesium alloy AM60. Multiple runs of the commercial casting simulation package, ProCASTTM, were used to model the mold filling and solidification events employing a range of interfacial heat transfer coefficient values. The simulation results were used to estimate the centerline cooling curve at various locations through the casting. The centerline cooling curves, together with the die temperature and the thermodynamic properties of the alloy, were then used as inputs to compute the solution to the Stefan problem of a moving phase boundary, thereby providing the through-thickness cooling curves at each chosen location of the casting, Finally, the local cooling rate was used to calculate the resulting grain size via previously established relationships. The effects of die temperature, filling time and heat transfer coefficient on the grain structure in skin region and core region were quantitatively characterized. It was observed that the grain size of skin region strongly depends on above three factors whereas the grain size of core region shows dependence on the interracial heat transfer coefficient and thickness of the samples. The grain size distribution from surface to center was estimated from the relationship between grain size and the predicted cooling rate. The prediction of grain size matches well with experimental results. A comparison of the predicted and experimentally determined grain size profiles enables the determination of the apparent interracial heat transfer coefficient for different locations.

Development and calibration of heat transfer coefficient sensor for rotational state

A novel heat transfer coefficient sensor is introduced and the design,manufacture,and calibration are described.The intended application of this instrument was on a high rotational speed test disc.In the experiments,the heat transfer coefficient sensor was calibrated under static state and rotational state respectively.The calibration under the static state was accomplished in a pipe: the inside diameter(ID) was 0.048m and the total length was 4m,the distance between the sensor and the inlet of the pipe was 3.5m;the standard value was measured using a self-made calibrator.The calibration under the rotational state was accomplished using a rotating disc: the diameter and thickness of the stainless disc were 800mm and 25mm,respectively;the sensor was installed at the location of r=250mm;the rotating disc driven by a 30kW direct current motor can supply the maximum rotational speed of 3000r/min.The standard value under rotational state was provided by an approximate empirical formula.The results show that the designed sensor can measure heat transfer coefficient directly under rotational state and static state with good accuracy and stability;the correlation factor of K are constant under static state and rotational state.

EXPERIMENTAL ANALYSIS OF THE TURBULENT TRANSFER COEFFICIENT FOR SENSIBLE HEAT IN THE SURFACE LAYER OVER THE QINGHAI-XIZANG PLATEAU

This study deals with the turbulent structure in the surface layer over the Qinghai-Xizang Plateau.Using gradient transfer and heat balance methods we have determined the nondimensional coefficient 1/(?)_m(?)h in the expression of turbulent transfer coefficient for sensible heat (K_h).It is found that the results are in good agreement with the 1/(?)_m(?)_h obtained by Pruitt,et al.The K_h at a height of 1m under cloudy and cloudless conditions is calculated.Finally,the ratio of K_h to momentum turbulent coefficient over the plateau is compared with those over plains.

Predictions of equilibrium solubility and mass transfer coefficient for CO_(2) absorption into aqueous solutions of 4-diethylamino-2-butanol using artificial neural networks

In the present work,artificial neuron network(ANN)based models for predicting equilibrium solubility and mass transfer coefficient of CO_(2) absorption into aqueous solutions of high performance alternative 4-diethylamino-2-butanol(DEAB)solvent were successfully developed.The ANN models show an outstanding predictive performance over the predictive correlations proposed in the literature.In order to predict the equilibrium solubility,the ANN model were developed based on three input parameters of operating temperature,concentration of DEAB and partial pressure of CO_(2).An outstanding prediction performance of 2.4%average absolute deviation(AAD)can be obtained(comparing with 7.1–8.3%AAD from the literature).Additionally,a significant improvement on predicting mass transfer coefficient can also be achieved through the developed ANN model with 3.1%AAD(comparing with 14.5%AAD from the existing semi-empirical model).The mass transfer coefficient is considered to be a function of liquid flow rate,liquid inlet temperature,concentration of DEAB,inlet CO_(2) loading,outlet CO_(2) loading,concentration of CO_(2) along the height of the column.

On the Effect of Mist Flow on the Heat Transfer Performances of a Three-Copper- Sphere Configuration

The cooling of a(pebble bed)spent fuel in a high-temperature gas-cooled reactor(HTGR)is adversely affected by an increase in the temperature of the used gas(air).To investigate this problem,a configuration consisting of three copper spheres arranged in tandem subjected to a forced mistflow inside a cylindrical channel is considered.The heat transfer coefficients and related variations as a function of Reynolds number are investigated accord-ingly.The experimental results show that when compared to those with only airflow,the heat transfer coefficient of the spherical elements with mistflow(j=112 kg/m2 hr,Re=55000)increases by 180%,75%,and 20%,respec-tively for thefirst,second,and third spherical element(the corresponding heat transfer enhancement ratio being 2.3,1.4,and 1.1).Additional numerical simulations reveal that the presence of stagnant zones with intense vortex formation around each spherical element contributes significantly to determine the heat transfer behavior.