Discussion on the application prospect of the transient electromagnetic method based on the dual launcher and mine advanced detection

The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.

3D forward modeling and response characteristics of low-resistivity overburden of the CFS-PML absorbing boundary for ground-well transient electromagnetic method

This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.

Mapping coalmine goaf using transient electromagnetic method and high density resistivity method in Ordos City, China

The research about subsurface characteristics by using transient electromagnetic method（TEM） and high density resistivity method（HDRM） were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values（30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3） are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values（20e26 U m of TEM, 45e75 U m of HDRM） at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.

Application of Transient Electromagnetic Method with Multi-Radiation Field Sources in Deep Edge Mineral Resources Exploration

In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international advanced method(Xue et al.,2020).

Simulation research and application on response characteristics of detecting water-filled goaf by transient electromagnetic method

Water inrush disasters poses a great threat to the safe exploitation of coal resources.To solve this problem,the transient electromagnetic method(TEM)was proposed to accurately detect the water accumulation in the goaf.The electromagnetic response characteristics of diferent water-flled goaves were studied by electromagnetic feld theory,numerical simulation and feld verifcation.Through the models of 100%water accumulation,50%water accumulation,0%water accumulation,100%water accumulation with collapsed rock,50%water accumulation with collapsed rock and 0%water accumulation with collapsed rock goaf,the characteristics of induced voltage attenuation curves were studied.Meanwhile,the relationship between the attenuation voltage value and area of the transmitting coil,the depth of the goaf,the background resistivity,and the delay time were also simulated.The results illustrate that the attenuation curve of induced voltage presented a regular exponential decay form in the 0%water accumulation model but existed abnormal exaltation for voltage in water-flled model.Through the linear ftting curve,it can be seen that the abnormal intensity of the induced voltage becomes stronger as the distance between the measuring point and the center of the target decrement.Moreover,the abnormal amplitude of the induced voltage increases with the rise of the water accumulation and collapsed rock will weakly reduce the low-resistivity anomalous efect on the water-accumulated goaf.In addition,the response value of the attenuation voltage increased as the area of the transmitting coil increases,but decreased with increasing delay time and increasing background resistivity and depth of the target body.The feld detection results of the Majiliang coal mine also confrmed the theoretical analysis and the numerical simulation.

One-dimensional constrained inversion of electrical source transient electromagnetic method

The damped least squares inversion principle is applied to the transient electromagnetic one-dimensional inversion of electrical sources,and a new model is obtained by continuously iterating the initial model,thereby fitting the observed transient electromagnetic response,and performing one-dimensional inversion through induced electromotive force play.In this paper,in the damped least squares inversion,constraints are added to the Jacobian matrix,and simultaneous constraint equations and conventional inversion equations are solved.By weighting the constraint parameters,the difference between adjacent resistivities and layer thicknesses is minimized.Finally,K-type and H-type theoretical models were used to verify the reliability of the algorithm,and compared with the conventional transient electromagnetic damping least squares inversion.

Forward simulation of coal fire model by transient electromagnetic method with electrical source

Uncontrolled coal fires are natural disasters that may cause mineral loss and environmental damage.The traditional loop source transient electromagnetic method can effectively detect the low-resistivity region of coal fires,but its detection efficiency is not so good for high-resistivity regions.In view of this limitation,a technique based on electrical source transient electromagnetics is proposed in this paper to detect high-resistivity regions in the spontaneous combustion process of coal.Considering the complex geometry of the coal fire area,an unstructured tetrahedral grid is used in this study to realize the spatial discretization of the model,and solve the electromagnetic field based on a vector finite element algorithm.Numerical analysis is used to investigate methods for detecting coal fires and the characteristics of effective anomalies are further examined to provide guidance for practical detection.

Study on the Coincident-Loop Transient Electromagnetic Method in Seafloor Exploration——Taking Jiaodong Polymetallic Mine as a Model

The transient electromagnetic(TEM)method becomes more urgent than ever for marine ex-ploration due to abundant resource reserves and the increasing undersea engineering construction activities,especially in the offshore exploration of mineral deposits such as Sanshandao gold mine.However,the re-search and application of TEM method in marine environment are still challenged by many problems.Such contradiction motivates our study on the coincident-loop TEM in seafloor exploration.The TEM response of coincident loops is firstly derived in the integral form,based on the potential functions in Helmholtz equ-ations for a magnetic source locating in the whole-space layered model.The frequency-domain vertical magnetic field is described as the Hankel integral with double first-order Bessel functions of first kind.Se-condly,the time-domain induced voltage is obtained by transforming the frequency-domain response through the cosine transform and then taking the derivative of time.To simultaneously solve the Hankel transform and the cosine transform,a novel algorithm is introduced by adapting the fixed-point quadra-ture and extrapolation via the Shanks transformation.Finally,a typical conductivity model for marine po-lymetallic deposit is designed to investigate the characteristic of TEM response under various conditions.Numerical results demonstrate that existence of conductive seawater causes the TEM response to increase significantly and decay slower.The air-sea reflected electromagnetic waves lead to a significantly large fake negative response(NR)in shallower seawater with depth less than 300 m.Increase in the height of loops will weaken and delay the anomaly response and shorten the observation time-window.The height of configu-ration should be no more than 100 m for shallower targets and 50 m for deeper targets,respectively.The observation time-window should cover 10-1000 ms.Increase in the radius of loops only enhances the TEM response proportionally but hardly improves the relative anomaly.The vertical resolution on the low-resistivity target approximates 20 m for the configuration considered in the study.Decreases in D.C.resistivity and chargeability cause the positive response(PR)to increase significantly and decay more ra-pidly.Meanwhile,the NR is advanced and enlarged significantly and decays slower compared with the PR.The influence of time constant is not monotony and there exists an optimal value for producing the maxi-mum NR.As the frequency parameter increases,the PR is caused to decay more rapidly without magni-tude change and the NR is advanced and decays more rapidly with significant increase in magnitude.The influence of frequency parameter is more pronounced than that of time constant.

A three-dimensional transient electromagnetic data inversion method based on a time–frequency transformation

Herein,a three-dimensional(3D)inversion method in the frequency domain based on a time–frequency transformation was developed to improve the efficiency of the 3D inversion of transient electromagnetic(TEM)data.The Fourier transform related to the electromagnetic response in the frequency and time domains becomes a sine or cosine transform under the excitation of downward-step current.We established a transformation matrix based on the digital fi ltering calculation for the sine transform,and then the frequency domain projection of the TEM data was determined from the linear transformation system using the smoothing constrained least squares inversion method,in which only the imaginary part was used to maintain the TEM data transformation equivalence in the bidirectional projection.Thus,the time-domain TEM inversion problem was indirectly and effectively solved in the frequency domain.In the 3D inversion of the transformed frequency-domain data,the limited-memory Broyden–Fletcher–Goldfarb–Shannoquasi–Newton(L-BFGS)method was used and modifi ed with a restart strategy to adjust the regularization parameter when the algorithm tended to a local minimum.Synthetic data tests showed that our domain transformation method can stably project the TEM data into the frequency domain with very high accuracy;furthe rmore,the 3D inversion of the transformed frequency-domain data is stable,can be used to recover the real resistivity model with an acceptable effi ciency.

Application of geophysical methods in fine detection of urban concealed karst:A case study of Wuhan City,China

The construction of modern livable cities faces challenges in karst areas,including ground collapse and engineering problems.Wuhan,with a population of 13.74×10^(6) and approximately 1161 km^(2)of soluble rocks in the urban area of 8569.15 km^(2),predominantly consists of concealed karst areas where occasional ground collapse events occur,posing significant threats to underground engineering projects.To address these challenges,a comprehensive geological survey was conducted in Wuhan,focusing on major karstrelated issues.Geophysical methods offer advantages over drilling in detecting concealed karst areas due to their efficiency,non-destructiveness,and flexibility.This paper reviewed the karst geological characteristics in Wuhan and the geophysical exploration methods for karst,selected eight effective geophysical methods for field experimentation,evaluated their suitability,and proposed method combinations for different karst scenarios.The results show that different geophysical methods have varying applicability for karst detection in Wuhan,and combining multiple methods enhances detection effectiveness.The specific recommendations for method combinations provided in this study serve as a valuable reference for karst detection in Wuhan.

EFFICIENT COMPUTATIONAL METHOD FOR TRANSIENT EM RESPONSE OF LARGE-LOOP SOURCE OVER LAYERED EARTH

Calculations of the ElectroMagnetic(EM) response produced by a large horizontal loop placed over layered medium are rather complex because its integral expression contains the product of two Bessel functions and has a divergent term. In this paper, an improved fast Hankel and Gaver-Stehfest transforms are introduced to solve the strong-oscillation and slow-decay properties of the integrand, where one Bessel function in the product is substituted by a carefully chosen polynomial of high accuracy and the other used as the digital filter coefficients in the convolution integral. Comparisons prove the validity and the efficiency of the proposed method.

Research and Application of Advanced Detection of Water Hazards in Coal Mine Bore-Hole

For many years, the “short excavation and short exploration” excavation mode has been mainly used in the underground tunnel excavation of coal mines, which is difficult to meet the needs of rapid tunnel excavation. For this reason, CCTEG Xi’an Research Institute has innovatively proposed a new working mode of “long excavation and long exploration” using directional long drilling and borehole geophysical exploration. This method utilizes directional long boreholes that have already been constructed, and uses transient electromagnetic technology in the borehole to detect the radial range of 30 meters and the depth exceeding 1000 meters of the borehole, ultimately forming a three-dimensional imaging of the entire spatial geological anomaly body, providing reliable technical support for the safety and long-term excavation of the tunnel. This paper introduces the application which is a long-distance advanced detection of 1026 m. .

Application Analysis of Various Geophysical Methods in Volume Calculation of Different Landfills

Garbage disposal has gradually become a key issue faced by environmental governance. What must be controlled in garbage disposal is the calculation of garbage volume. In this paper, according to the different landfill conditions of a landfill in Anhui, including: covering soil, overlying HDPE membrane, overlying concrete, etc., combined with the physical differences between the rock mass and the garbage at the bottom of the landfill. The landfill covered with HDPE membrane adopts the transient electromagnetic method, the landfill covered with soil layer adopts the high-density electrical method, and the landfill covered with concrete adopts the combination of transient electromagnetic method and ground penetrating radar. At the same time, Combines the borehole data to determine that the resistivity value of the interface between the garbage and the soil was 29 Ω⋅m. Finally, the sections of multiple survey lines can accomplish three-dimensional stereoscopic that calculate the distribution and actual volume of the garbage. This method is used to determine the final investment cost.

Transient electromagnetic detection method in water-sealed underground storage caverns

Taking advantage of the water sensitivity of the transient electromagnetic method(TEM),this study assesses the effectiveness of the water curtain system for underground LPG storage caverns during the excavation period.It also detects fracture water flow during the excavation process in light of the practice of two pilot large underground LPG storage caverns in China.Comparative maps of apparent resistivity derived from TEM measurements before and after water-filling during the excavation process have been discussed to improve the quality of the water curtain system.This is the first case to apply TEM to detect the quality of the water curtain system during the construction of underground LPG storage cavern projects,and it is found to be practical,more visualized and worth popularizing.

Predicting geological hazards during tunnel construction

The complicated geological conditions and geological hazards are challenging problems during tunnel construction,which will cause great losses of life and property.Therefore,reliable prediction of geological defective features,such as faults,karst caves and groundwater,has important practical significances and theoretical values.In this paper,we presented the criteria for detecting typical geological anomalies using the tunnel seismic prediction（TSP） method.The ground penetrating radar（GPR） signal response to water-bearing structures was used for theoretical derivations.And the 3D tomography of the transient electromagnetic method（TEM） was used to develop an equivalent conductance method.Based on the improvement of a single prediction technique,we developed a technical system for reliable prediction of geological defective features by analyzing the advantages and disadvantages of all prediction methods.The procedure of the application of this system was introduced in detail.For prediction,the selection of prediction methods is an important and challenging work.The analytic hierarchy process（AHP） was developed for prediction optimization.We applied the newly developed prediction system to several important projects in China,including Hurongxi highway,Jinping II hydropower station,and Kiaochow Bay subsea tunnel.The case studies show that the geological defective features can be successfully detected with good precision and efficiency,and the prediction system is proved to be an effective means to minimize the risks of geological hazards during tunnel construction.

TEM investigations of South Atlantic Ridge 13.2°S hydrothermal area

According to the exploration contract about polymetallic sulfides in the SWIR （Southwest Indian Ridge） signed by China with the International Seabed Authority, to delineate sulfide minerals and estimate resource quantity are urgent tasks. We independently developed our first coincident loop Transient Electromagnetic Method （TEM） device in 2010, and gained the TEM data for seafloor sulfide at South Atlantic Ridge 13.2°S in June 2011. In contrast with the widely applied CSEM （Marine controlled-source electromagnetic） method, whose goal is to explore hydrocarbons （oil/gas） of higher resistivity than seawater from 102 to 103 m below the sea floor, the TEM is for low resistivity minerals, and the target depth is from 0 to 100 m below the sea floor. Based on the development of complex sulfide geoelectrial models, this paper analyzed the TEM data obtained, proposing a new method for seafloor sulfide detection. We present the preliminary trial results, in the form of apparent resistivity sections for both half-space and full-space conditions. The results cor- respond well with the observations of the actual hydrothermal vent area, and the detection depth reached 50-100m below the bed, which verified the capability of the equipment.