The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed t...The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed to capture the rotation of the lobes. The numerical model is validated by comparing the simulated results with the literature values. The processes of suction, displacement, compression and exhaust are accurately captured in the transient simulation. The fluid pressure value remains in the range of inlet pressure value till the processes of suction and displacement are over. The instantaneous process of compression is accurately captured in the simulation. The movement of a particular working chamber is traced along the gradual degree of lobe’s rotation. At five different degrees of lobe’s rotation, pressure contour plots are reported which clearly shows the pressure values inside the working chamber. Each pressure value inside the working chamber conforms to the particular process in which the working chamber is operating. Finally, the power requirement at the shaft of rotation is estimated from the simulated values. The estimated value of power requirement is 3.61 BHP FHP whereas the same calculated theoretically is 3 BHP FHP. The discrepancy is attributed to the assumption of symmetry of blower along the thickness.展开更多
In this paper, two-dimensional (2D) transient simulations of an A1GaN/GaN high-electron-mobility transistor (HEMT) are carded out and analyzed to investigate the current collapse due to trapping effects. The coupl...In this paper, two-dimensional (2D) transient simulations of an A1GaN/GaN high-electron-mobility transistor (HEMT) are carded out and analyzed to investigate the current collapse due to trapping effects. The coupling effect of the trapping and thermal effects are taken into account in our simulation. The turn-on pulse gate-lag transient responses with different quiescent biases are obtained, and the pulsed current-voltage (l-V) curves are extracted from the transients. The experimental results of both gate-lag transient current and pulsed I-V curves are reproduced by the simulation, and the current collapse due to the trapping effect is explained from the view of physics based on the simulation results. In addition, the results show that bulk acceptor traps can influence the gate-lag transient characteristics of A1GaN/GaN HEMTs besides surface traps and that the thermal effect can accelerate the emission of captured electrons for traps. Pulse transient simulation is meaningful in analyzing the mechanism of dynamic current collapse, and the work in this paper will benefit the reliability study and model development of GaN-based devices.展开更多
This article presents a modeling and simulation method for transient thermal analyses of integrated circuits(ICs)using the original and voltage-in-current(VinC)latency insertion method(LIM).LIM-based algorithms are a ...This article presents a modeling and simulation method for transient thermal analyses of integrated circuits(ICs)using the original and voltage-in-current(VinC)latency insertion method(LIM).LIM-based algorithms are a set of fast transient simulation methods that solve electrical circuits in a leapfrog updating manner without relying on large matrix operations used in conventional Simulation Program with Integrated Circuit Emphasis(SPICE)-based methods which can significantly slow down the solution process.The conversion from the thermal to electrical model is performed first by using the analogy between heat and electrical conduction.Since electrical inductance has no thermal equivalence,a modified VinC LIM formulation is presented which removes the requirement of the insertion of fictitious inductors.Numerical examples are presented,which show that the modified VinC LIM formulation outperforms the basic LIM formulation,in terms of both stability and accuracy in the transient thermal simulation of ICs.展开更多
A modeling method of regional integrated energy system based on bus method and transient simulation is proposed,and the system optimization is based on the dynamic balance of supply and demand in the whole year energy...A modeling method of regional integrated energy system based on bus method and transient simulation is proposed,and the system optimization is based on the dynamic balance of supply and demand in the whole year energy supply cycle.A CCHP systemof gas turbine coupled with ground source heat pump and electric refrigeration unit is constructed.The energy relationship of the systemis described by bus structure,and the transient calculationmodel is built on TRNSYS platform.The weighted sum of annual total cost saving rate,primary energy saving rate and environmental pollutant shadow cost saving rate is taken as the optimized objective function,and on the basis of annual dynamic balance,the Hooke-Jeeves algorithm is used for optimization of the system configuration.A complex commercial area in Beijing is taken as an example,and different weighting coefficients are set for optimization of the system configuration.The results show that,from the perspective of economy,environmental benefit and primary energy consumption,performance of the system increases and then decreases with rise of gas turbine power;under the simulated cooling/heating load,the maximum number of optimum configuration is seen in the combination of 35 kW gas turbine+723 kW GSHP and 1178 kW electric chiller;in comparison with traditional distributed system,the annual cost saving rate,primary energy saving rate and environmental pollutant shadow cost saving rate of the system are 29.4%,49.6%and 58.2%,respectively.展开更多
A unified chemistry-aerosol-climate model is applied in this work to compare climate responses to changing concentrations of long-lived greenhouse gases (GHGs, CO2, CH4, N2O), tropospheric O3, and aerosols during th...A unified chemistry-aerosol-climate model is applied in this work to compare climate responses to changing concentrations of long-lived greenhouse gases (GHGs, CO2, CH4, N2O), tropospheric O3, and aerosols during the years 1951-2000. Concentrations of sulfate, nitrate, primary organic carbon (POA), secondary organic carbon (SOA), black carbon (BC) aerosols, and tropospheric 03 for the years 1950 and 2000 are obtained a priori by coupled chemistry-aerosol-GCM simulations, and then monthly concentrations are interpolated linearly between 1951 and 2000. The annual concentrations of GHGs are taken from the IPCC Third Assessment Report. BC aerosol is internally mixed with other aerosols. Model results indicate that the sinmlated climate change over 1951-2000 is sensitive to anthropogenic changes in atmospheric components. The predicted year 2000 global mean surface air temperature can differ by 0.8℃ with different forcings. Relative to the climate simulation without changes in GHGs, O3, and aerosols, anthropogenic forcings of SO4^2-, BC, BC+SO4^2-, BC+SO4^2- +POA, BC+SO4^2- +POA+SOA+NO3^-, O3, and GHGs are predicted to change the surface air temperature averaged over 1971-2000 in eastern China, respectively, by -0.40℃, +0.62℃, +0.18℃, +0.15℃, -0.78℃, +0.43℃, and +0.85℃, and to change the precipitation, respectively, by -0.21, +0.07, -0.03, +0.02, -0.24, -0.08, and +0.10 mm d^-1. The authors conclude that all major aerosols are as important as GHGs in influencing climate change in eastern China, and tropospheric O3 also needs to be included in studies of regional climate change in China.展开更多
To perform nuclear reactor simulations in a more realistic manner,the coupling scheme between neutronics and thermal-hydraulics was implemented in the HNET program for both steady-state and transient conditions.For si...To perform nuclear reactor simulations in a more realistic manner,the coupling scheme between neutronics and thermal-hydraulics was implemented in the HNET program for both steady-state and transient conditions.For simplicity,efficiency,and robustness,the matrixfree Newton/Krylov(MFNK)method was applied to the steady-state coupling calculation.In addition,the optimal perturbation size was adopted to further improve the convergence behavior of the MFNK.For the transient coupling simulation,the operator splitting method with a staggered time mesh was utilized to balance the computational cost and accuracy.Finally,VERA Problem 6 with power and boron perturbation and the NEACRP transient benchmark were simulated for analysis.The numerical results show that the MFNK method can outperform Picard iteration in terms of both efficiency and robustness for a wide range of problems.Furthermore,the reasonable agreement between the simulation results and the reference results for the NEACRP transient benchmark verifies the capability of predicting the behavior of the nuclear reactor.展开更多
Determining the venting time of a gas trunk pipeline segment provides an important basis for formulating an emergency plan in the advent of unexpected accidents.As the natural gas venting process corresponds to the tr...Determining the venting time of a gas trunk pipeline segment provides an important basis for formulating an emergency plan in the advent of unexpected accidents.As the natural gas venting process corresponds to the transient flow,it is necessary to establish a transient hydraulic-thermal simulation model in order to determine the venting time.In this paper,based on two kinds of venting scenarios in which there is only one venting point in the venting system of a gas trunk pipeline segment—namely,where the venting point is either at one of the two ends or at the junction of two gas trunk pipeline segments—transient hydraulic-thermal simulation models are established.The models consist of gas flow governing equations,the gas state equation,gas physical property equations,initial conditions,and appropriate boundary conditions.The implicit central difference method is used to discretize the gas flow partial differential equations,and the trust-region-dogleg algorithm is used to solve the equations corresponding to each time step,in order to dynamically simulate the whole venting process.The judgment condition for the end of the venting process is that the average pressure of gas trunk pipeline segment is less than 0.11 MPa(actual pressure).Comparing the simulation results of the proposed model with those of the OLGA software and real operational data,we find that the venting time error is less than 10%.On this basis,a venting valve opening control principle is proposed,which prevents the venting noise from exceeded the specified noise value(85 d B)in the venting design of domestic gas pipeline projects.The established calculation model for venting time(dynamic simulation model)for a gas trunk pipeline segment and the proposed opening control principle of venting valve provide reference for the optimal operation of gas pipeline venting systems.展开更多
Although the Combined Cooing,Heating and Power System(hereinafter referred to as“CCHP”)improves the capacity utilization rate and energy utilization efficiency,single use of CCHP system cannot realize dynamic matchi...Although the Combined Cooing,Heating and Power System(hereinafter referred to as“CCHP”)improves the capacity utilization rate and energy utilization efficiency,single use of CCHP system cannot realize dynamic matching between supply and demand loads due to the unbalance features of the user’s cooling and heating loads.On the basis of user convenience and wide applicability of clean air energy,this paper tries to put forward a coupled CCHP system with combustion gas turbine and ASHP ordered power by heat,analyze trends of such parameters as gas consumption and power consumption of heat pump in line with adjustment of heating load proportion of combustion gas turbine,and optimize the system ratio in the method of annual costs and energy environmental benefit assessment.Based on the analysis of the hourly simulation and matching characteristics of the cold and hot load of the 100 thousand square meter building,it is found that the annual cost of the air source heat pump is low,but the energy and environmental benefits are poor.It will lead to 6.35%shortage of cooling load in summer.Combined with the evaluation method of primary energy consumption and zero carbon dioxide emission,the coupling system of CHHP and air source heat pump with 41%gas turbine load ratio is the best configuration.This system structure and optimization method can provide some reference for the development of CCHP coupling system.展开更多
In order to effectively imitate the dynamic operation characteristics of the HVDC (high voltage direct current) power transmission system at a real ±500kV HVDC transmission project, the electromechanical-electr...In order to effectively imitate the dynamic operation characteristics of the HVDC (high voltage direct current) power transmission system at a real ±500kV HVDC transmission project, the electromechanical-electromagnetic transient hybrid simulation was carried out based on advanced digital power system simulator (ADPSS). In the simulation analysis, the built hybrid model's dynamic response outputs under three different fault conditions are considered, and by comparing with the selected fault recording waveforms, the validities of the simulation waveforms are estimated qualitatively. It can be ascertained that the hybrid simulation model has the ability to describe the HVDC system's dynamic change trends well under some special fault conditions.展开更多
We have developed an energy balance equation for the universe. The two system parameters involved in the equation could be “fine-tuned” so that the predicted temperature histories all lead to what is observed in the...We have developed an energy balance equation for the universe. The two system parameters involved in the equation could be “fine-tuned” so that the predicted temperature histories all lead to what is observed in the present cosmic microwave background. We have shown that various combinations of these two parameters are possible;in particular, the present background temperature needs not be the remnant of a very hot temperature in the far distance past. We also solved for the propagation of vortex solitons in optical fibres as contrasting examples to show how electromagnetic wave could be transmitted in a particular waveform under strictly controlled conditions. To avoid singularity, all vortexes have a black centre. We conclude that while numerical techniques can be used to account for an infinite quantity, it is unlikely that such a quantity could exist in reality.展开更多
Wind-driven rain(WDR)has a significant influence on the hygrothermal performance,durability,and energy consumption of building components.The calculation of WDR loads using semi-empirical models has been incorporated ...Wind-driven rain(WDR)has a significant influence on the hygrothermal performance,durability,and energy consumption of building components.The calculation of WDR loads using semi-empirical models has been incorporated into the boundary conditions of coupled heat and moisture transfer models.However,prior research often relied on fixed WDR absorption ratio,which fail to accurately capture the water absorption characteristics of porous building materials under rainfall scenarios.Therefore,this study aims to investigate the coupled heat and moisture transfer of exterior walls under dynamic WDR boundary conditions,utilizing an empirically obtained WDR absorption ratio model based on field measurements.The developed coupled heat and moisture transfer model is validated against the HAMSTAD project.The findings reveal that the total WDR flux calculated with the dynamic WDR boundary is lower than that obtained with the fixed WDR boundary,with greater disparities observed in orientations experiencing higher WDR loads.The variations in moisture flow significantly impact the surface temperature and relative humidity of the walls,influencing the calculation of cooling and heating loads by different models.Compared to the transient heat transfer model,the coupled heat and moisture transfer model incorporating dynamic WDR boundary exhibits maximum increases of 17.6%and 16.2%in cooling and heating loads,respectively.The dynamic WDR boundary conditions provide more precise numerical values for surface moisture flux,offering valuable insights for the thermal design of building enclosures and load calculations for HVAC systems.展开更多
Due to the large eddy currents at the ends of the quadrupole magnets for CSNS/RCS, the magnetic field properties and the heat generation are of great concern. In this paper, we take transient electromagnetic simulatio...Due to the large eddy currents at the ends of the quadrupole magnets for CSNS/RCS, the magnetic field properties and the heat generation are of great concern. In this paper, we take transient electromagnetic simulation and make use of the eddy current loss from the transient electromagnetic results to perform thermal analysis. Through analysis of the simulated results, the magnetic field dynamic properties of these magnets and a temperature rise are achieved. Finally, the accuracy of the thermal analysis is confirmed by a test of the prototype quadrupole magnet of the RCS.展开更多
In order to alleviate the pressure of experi- mental research of turbocharged diesel engine under transient operations, a whole process simulation platform for turbocharged diesel engine under transient operations was...In order to alleviate the pressure of experi- mental research of turbocharged diesel engine under transient operations, a whole process simulation platform for turbocharged diesel engine under transient operations was established based on the multi-software coupling technologies of Matlab/Simulink, GT-Power, STAR-CD and artificial neural network. Aimed at the contradiction of NOx and soot emission control with exhaust gas recirculation (EGR) of turbocharged diesel engine under transient operations, on this simulation platform, a transient EGR valve control strategy was proposed, which adjusted the EGR valve in adjacent level based on the feedback of its opening according soot control limit under transient operations. Simulation and experimental results prove that the transient emission optimization effect of this control strategy is obvious. On the one hand, compared with the previous control strategy, which closed the EGR valve during the whole transient operations, soot emission is slightly increased by 9.5%, but it is still 9% lower than the control limit. On the other hand, compared with the previous control strategy, NOx transient emission is reduced by 44%.展开更多
The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–sol...The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.展开更多
Effective model reduction methods are required to deal with new challenges in active distribution network simulations that are on a large scale and have complicated structures.In the development of advanced electromag...Effective model reduction methods are required to deal with new challenges in active distribution network simulations that are on a large scale and have complicated structures.In the development of advanced electromagnetic transient simulation programs,automated model reduction plays an important role.This paper proposes an automated realization algorithm for the Krylov subspace based model reduction methods of an active distribution network with which the reduced model can be automatically established according to a given threshold of reduction error.The combined state-space nodal analysis framework is employed to apply the automated model reduction algorithm in popular EMTP-type simulation programs.Simulations are performed using PSCAD and a self-developed program to show the feasibility and validity of the proposed methods.展开更多
The gas-liquid two-phase flow patterns of a centrifugal pump during the self-priming process were investigated numerically and experimentally.The Euler-Euler multiphase model and SST k-ω turbulence model were applied...The gas-liquid two-phase flow patterns of a centrifugal pump during the self-priming process were investigated numerically and experimentally.The Euler-Euler multiphase model and SST k-ω turbulence model were applied for simulating the self-priming process.Meanwhile,the changes of motor speed and self-priming height were considered in the simulation.The overall transient two-phase flow features and water level distributions were mapped.Results showed that the self-priming process was divided into three stages.The liquid level in inlet-pipe rose in oscillation during self-priming process.The variations of water level during self-priming process of numerical simulation and test result agreed well.The inlet-pipe(Ver)was filled at 22 s and 24 s respectively numerically and experimentally.The bubble cloud circulated in the volute during middle stage of self-priming process,and breakup into smaller bubbles by shear force and tongue,and then discharged into chamber.The bubbles in the outlet-pipe mainly included bubbly flow and slug flow at the last stage of self-priming process,which is morphologically consistent with the test results.Also,during the self-priming process,the reflux liquid was pressed by blades and fully mixed with gas;that is the way to realizing the function of self-priming.展开更多
Trap-induced current collapse has become one of the critical issues hindering the improvement of Ga Nbased microwave power devices. It is difficult to study the behavior of each trapping effect separately with the exp...Trap-induced current collapse has become one of the critical issues hindering the improvement of Ga Nbased microwave power devices. It is difficult to study the behavior of each trapping effect separately with the experimental measurement. Transient simulation is a useful technique for analyzing the mechanism of current collapse. In this paper, the coeffect of surface-and bulk-trapping behaviors on the performance of Al Ga N/Ga N HEMTs is investigated based on the two-dimensional(2 D) transient simulation. In addition, the mechanism of trapping effects is analyzed from the aspect of device physics. Two simulation models with different types of traps are used for comparison, and the simulated results reproduced the experimental measured data. It is found that the final steady-state current decreases when both the surface and bulk traps are taken into account in the model.However, contrary to the expectation, the total current collapse is dramatically reduced(e.g. from 18% to 4% for the 90 nm gate-length device). The results suggest that the surface-related current collapse of Ga N-based HEMTs may be mitigated in some degree due to the participation of bulk traps with short time constant. The work in this paper will be helpful for further optimization design of material and device structures.展开更多
Half-wavelength AC Transmission(HWACT)can improve capability of AC transmission significantly.According to the basic principle of HWACT,the electromagnetic transient model of HWACT is built to analyze the fault transi...Half-wavelength AC Transmission(HWACT)can improve capability of AC transmission significantly.According to the basic principle of HWACT,the electromagnetic transient model of HWACT is built to analyze the fault transient process of transmission line.Based on fault characteristics of HWACT,the adaptability of traditional protections for transmission lines is analyzed briefly,such as current differential protection,distance protection and over current protection.In order to solve the problems of conventional protection caused by HWACT,a novel integrated protection based on multi-frequency domain information is proposed in this paper,which uses both the power frequency information and transient information.The integrated protection based on multi-frequency domain information takes advantages of power frequency and transient protections,which can not only improve the performance of traditional protection of AC transmission line but also realize fast fault judgment by transient travelling wave protection.展开更多
In this paper,experiment results about East Asia climate from five CGCMs are described.The ability of the models to simulate present climate and the simulated response to increased carbon dioxide are both covered.The ...In this paper,experiment results about East Asia climate from five CGCMs are described.The ability of the models to simulate present climate and the simulated response to increased carbon dioxide are both covered.The results indicate that all models show substantial changes in climate when carbon dioxide concentrations are doubled.In particular,the strong surface warming at high latitudes in winter and the significant increase of summer precipitation in the monsoon area are produced by all models.Regional evaluation results show that these five CGCMs are particularly good in simulating spatial distribution of present climate.The main characteristics of the seasonal mean H500,SAT, MSLP field can be simulated by most CGCMs.But there are significant systematic errors in SAT, MSLP,HS00 fields in most models.On the whole,DKRZ OPYC is the best in simulating the present climate in East Asia.展开更多
Background Indirect cooling method is an alternative scheme for magnetic alloy(MA)-loaded cavity because of the feasible structure and MA core treatment process.Stable and long-term operation is not possible without a...Background Indirect cooling method is an alternative scheme for magnetic alloy(MA)-loaded cavity because of the feasible structure and MA core treatment process.Stable and long-term operation is not possible without a powerful cooling system for the high-power MA cavity.Purpose The paper reports a method to evaluate the cooling efficiency of an indirect cooling structure for high-power-loss MA cavity.Methods Two types of helix metallic cooling plate were designed and checked by CFX code considering the average power loss more than 0.13 W/cc.In order to enhance the heat-transfer efficiency between the non-flatness surface of the MA core and metallic cooling plate,a filling material with high thermal conductivity is needed.Different commercial filling materials were investigated,and a high-power test bench was developed to assess the cooling efficiency.A parametric fitting method was adopted to qualify the heat-transfer coefficient according to the temperature rising curve.Conclusion The results indicate that the experimental data maintain good consistency with the CFX simulation results and the cooling structure meets the high-power-loss cooling requirement.The heat-transfer capability of the filling was influenced by the thickness of heat-transfer materials and the painting process.The heat-transfer performance of the thermal grease is better than that of the thermal gasket even though the latter has a higher thermal conductivity.The virtual thermal conductivity of the filling material was less than the product index and affirmed by the CFX transient simulation.展开更多
文摘The performance of a newly designed tri-lobe industrial lobe pump of high capacity is simulated by using commercial CFD solver Ansys Fluent. A combination of user-defined-functions and meshing strategies is employed to capture the rotation of the lobes. The numerical model is validated by comparing the simulated results with the literature values. The processes of suction, displacement, compression and exhaust are accurately captured in the transient simulation. The fluid pressure value remains in the range of inlet pressure value till the processes of suction and displacement are over. The instantaneous process of compression is accurately captured in the simulation. The movement of a particular working chamber is traced along the gradual degree of lobe’s rotation. At five different degrees of lobe’s rotation, pressure contour plots are reported which clearly shows the pressure values inside the working chamber. Each pressure value inside the working chamber conforms to the particular process in which the working chamber is operating. Finally, the power requirement at the shaft of rotation is estimated from the simulated values. The estimated value of power requirement is 3.61 BHP FHP whereas the same calculated theoretically is 3 BHP FHP. The discrepancy is attributed to the assumption of symmetry of blower along the thickness.
基金Project supported by the National Natural Science Foundation of China(Grant No.61306113)
文摘In this paper, two-dimensional (2D) transient simulations of an A1GaN/GaN high-electron-mobility transistor (HEMT) are carded out and analyzed to investigate the current collapse due to trapping effects. The coupling effect of the trapping and thermal effects are taken into account in our simulation. The turn-on pulse gate-lag transient responses with different quiescent biases are obtained, and the pulsed current-voltage (l-V) curves are extracted from the transients. The experimental results of both gate-lag transient current and pulsed I-V curves are reproduced by the simulation, and the current collapse due to the trapping effect is explained from the view of physics based on the simulation results. In addition, the results show that bulk acceptor traps can influence the gate-lag transient characteristics of A1GaN/GaN HEMTs besides surface traps and that the thermal effect can accelerate the emission of captured electrons for traps. Pulse transient simulation is meaningful in analyzing the mechanism of dynamic current collapse, and the work in this paper will benefit the reliability study and model development of GaN-based devices.
基金This work was supported by the Fundamental Research Grant Scheme(FRGS)sponsored by the Ministry of Higher Education,Malaysia under Grant No.FRGS/1/2020/TK0/USM/02/7.
文摘This article presents a modeling and simulation method for transient thermal analyses of integrated circuits(ICs)using the original and voltage-in-current(VinC)latency insertion method(LIM).LIM-based algorithms are a set of fast transient simulation methods that solve electrical circuits in a leapfrog updating manner without relying on large matrix operations used in conventional Simulation Program with Integrated Circuit Emphasis(SPICE)-based methods which can significantly slow down the solution process.The conversion from the thermal to electrical model is performed first by using the analogy between heat and electrical conduction.Since electrical inductance has no thermal equivalence,a modified VinC LIM formulation is presented which removes the requirement of the insertion of fictitious inductors.Numerical examples are presented,which show that the modified VinC LIM formulation outperforms the basic LIM formulation,in terms of both stability and accuracy in the transient thermal simulation of ICs.
基金This research was funded by the Research on Rapid Modeling Methods for Integrated Energy Systems,Grant No.SGTYHT/17-JS-204.
文摘A modeling method of regional integrated energy system based on bus method and transient simulation is proposed,and the system optimization is based on the dynamic balance of supply and demand in the whole year energy supply cycle.A CCHP systemof gas turbine coupled with ground source heat pump and electric refrigeration unit is constructed.The energy relationship of the systemis described by bus structure,and the transient calculationmodel is built on TRNSYS platform.The weighted sum of annual total cost saving rate,primary energy saving rate and environmental pollutant shadow cost saving rate is taken as the optimized objective function,and on the basis of annual dynamic balance,the Hooke-Jeeves algorithm is used for optimization of the system configuration.A complex commercial area in Beijing is taken as an example,and different weighting coefficients are set for optimization of the system configuration.The results show that,from the perspective of economy,environmental benefit and primary energy consumption,performance of the system increases and then decreases with rise of gas turbine power;under the simulated cooling/heating load,the maximum number of optimum configuration is seen in the combination of 35 kW gas turbine+723 kW GSHP and 1178 kW electric chiller;in comparison with traditional distributed system,the annual cost saving rate,primary energy saving rate and environmental pollutant shadow cost saving rate of the system are 29.4%,49.6%and 58.2%,respectively.
基金supported by the National Natural Science Foundation of China(Grant Nos90711004 and 40825016)the Chinese Academy of Sciences(Grant Nos:KZCX2-YW-Q1-02,KZCX2-YW-Q11-03)
文摘A unified chemistry-aerosol-climate model is applied in this work to compare climate responses to changing concentrations of long-lived greenhouse gases (GHGs, CO2, CH4, N2O), tropospheric O3, and aerosols during the years 1951-2000. Concentrations of sulfate, nitrate, primary organic carbon (POA), secondary organic carbon (SOA), black carbon (BC) aerosols, and tropospheric 03 for the years 1950 and 2000 are obtained a priori by coupled chemistry-aerosol-GCM simulations, and then monthly concentrations are interpolated linearly between 1951 and 2000. The annual concentrations of GHGs are taken from the IPCC Third Assessment Report. BC aerosol is internally mixed with other aerosols. Model results indicate that the sinmlated climate change over 1951-2000 is sensitive to anthropogenic changes in atmospheric components. The predicted year 2000 global mean surface air temperature can differ by 0.8℃ with different forcings. Relative to the climate simulation without changes in GHGs, O3, and aerosols, anthropogenic forcings of SO4^2-, BC, BC+SO4^2-, BC+SO4^2- +POA, BC+SO4^2- +POA+SOA+NO3^-, O3, and GHGs are predicted to change the surface air temperature averaged over 1971-2000 in eastern China, respectively, by -0.40℃, +0.62℃, +0.18℃, +0.15℃, -0.78℃, +0.43℃, and +0.85℃, and to change the precipitation, respectively, by -0.21, +0.07, -0.03, +0.02, -0.24, -0.08, and +0.10 mm d^-1. The authors conclude that all major aerosols are as important as GHGs in influencing climate change in eastern China, and tropospheric O3 also needs to be included in studies of regional climate change in China.
基金supported by the China Postdoctoral Science Foundation(No.2021M703045)the National Natural Science Foundation of China(No.12075067)the National Key R&D Program of China(No.2018YFE0180900).
文摘To perform nuclear reactor simulations in a more realistic manner,the coupling scheme between neutronics and thermal-hydraulics was implemented in the HNET program for both steady-state and transient conditions.For simplicity,efficiency,and robustness,the matrixfree Newton/Krylov(MFNK)method was applied to the steady-state coupling calculation.In addition,the optimal perturbation size was adopted to further improve the convergence behavior of the MFNK.For the transient coupling simulation,the operator splitting method with a staggered time mesh was utilized to balance the computational cost and accuracy.Finally,VERA Problem 6 with power and boron perturbation and the NEACRP transient benchmark were simulated for analysis.The numerical results show that the MFNK method can outperform Picard iteration in terms of both efficiency and robustness for a wide range of problems.Furthermore,the reasonable agreement between the simulation results and the reference results for the NEACRP transient benchmark verifies the capability of predicting the behavior of the nuclear reactor.
基金supported by the National Natural Science Foundation of China(Grant No.52174064)
文摘Determining the venting time of a gas trunk pipeline segment provides an important basis for formulating an emergency plan in the advent of unexpected accidents.As the natural gas venting process corresponds to the transient flow,it is necessary to establish a transient hydraulic-thermal simulation model in order to determine the venting time.In this paper,based on two kinds of venting scenarios in which there is only one venting point in the venting system of a gas trunk pipeline segment—namely,where the venting point is either at one of the two ends or at the junction of two gas trunk pipeline segments—transient hydraulic-thermal simulation models are established.The models consist of gas flow governing equations,the gas state equation,gas physical property equations,initial conditions,and appropriate boundary conditions.The implicit central difference method is used to discretize the gas flow partial differential equations,and the trust-region-dogleg algorithm is used to solve the equations corresponding to each time step,in order to dynamically simulate the whole venting process.The judgment condition for the end of the venting process is that the average pressure of gas trunk pipeline segment is less than 0.11 MPa(actual pressure).Comparing the simulation results of the proposed model with those of the OLGA software and real operational data,we find that the venting time error is less than 10%.On this basis,a venting valve opening control principle is proposed,which prevents the venting noise from exceeded the specified noise value(85 d B)in the venting design of domestic gas pipeline projects.The established calculation model for venting time(dynamic simulation model)for a gas trunk pipeline segment and the proposed opening control principle of venting valve provide reference for the optimal operation of gas pipeline venting systems.
基金This research was funded by the research on rapid modeling methods for integrated energy systems,Grant No.SGTYHT/17-JS-204.
文摘Although the Combined Cooing,Heating and Power System(hereinafter referred to as“CCHP”)improves the capacity utilization rate and energy utilization efficiency,single use of CCHP system cannot realize dynamic matching between supply and demand loads due to the unbalance features of the user’s cooling and heating loads.On the basis of user convenience and wide applicability of clean air energy,this paper tries to put forward a coupled CCHP system with combustion gas turbine and ASHP ordered power by heat,analyze trends of such parameters as gas consumption and power consumption of heat pump in line with adjustment of heating load proportion of combustion gas turbine,and optimize the system ratio in the method of annual costs and energy environmental benefit assessment.Based on the analysis of the hourly simulation and matching characteristics of the cold and hot load of the 100 thousand square meter building,it is found that the annual cost of the air source heat pump is low,but the energy and environmental benefits are poor.It will lead to 6.35%shortage of cooling load in summer.Combined with the evaluation method of primary energy consumption and zero carbon dioxide emission,the coupling system of CHHP and air source heat pump with 41%gas turbine load ratio is the best configuration.This system structure and optimization method can provide some reference for the development of CCHP coupling system.
基金supported by the General Program of Chinese Postdoctoral Science Foundation under Grant No.2012M511595
文摘In order to effectively imitate the dynamic operation characteristics of the HVDC (high voltage direct current) power transmission system at a real ±500kV HVDC transmission project, the electromechanical-electromagnetic transient hybrid simulation was carried out based on advanced digital power system simulator (ADPSS). In the simulation analysis, the built hybrid model's dynamic response outputs under three different fault conditions are considered, and by comparing with the selected fault recording waveforms, the validities of the simulation waveforms are estimated qualitatively. It can be ascertained that the hybrid simulation model has the ability to describe the HVDC system's dynamic change trends well under some special fault conditions.
文摘We have developed an energy balance equation for the universe. The two system parameters involved in the equation could be “fine-tuned” so that the predicted temperature histories all lead to what is observed in the present cosmic microwave background. We have shown that various combinations of these two parameters are possible;in particular, the present background temperature needs not be the remnant of a very hot temperature in the far distance past. We also solved for the propagation of vortex solitons in optical fibres as contrasting examples to show how electromagnetic wave could be transmitted in a particular waveform under strictly controlled conditions. To avoid singularity, all vortexes have a black centre. We conclude that while numerical techniques can be used to account for an infinite quantity, it is unlikely that such a quantity could exist in reality.
基金The work described in this paper was financially supported by the Shanghai Municipality Natural Science Foundation(No.21ZR1434400).
文摘Wind-driven rain(WDR)has a significant influence on the hygrothermal performance,durability,and energy consumption of building components.The calculation of WDR loads using semi-empirical models has been incorporated into the boundary conditions of coupled heat and moisture transfer models.However,prior research often relied on fixed WDR absorption ratio,which fail to accurately capture the water absorption characteristics of porous building materials under rainfall scenarios.Therefore,this study aims to investigate the coupled heat and moisture transfer of exterior walls under dynamic WDR boundary conditions,utilizing an empirically obtained WDR absorption ratio model based on field measurements.The developed coupled heat and moisture transfer model is validated against the HAMSTAD project.The findings reveal that the total WDR flux calculated with the dynamic WDR boundary is lower than that obtained with the fixed WDR boundary,with greater disparities observed in orientations experiencing higher WDR loads.The variations in moisture flow significantly impact the surface temperature and relative humidity of the walls,influencing the calculation of cooling and heating loads by different models.Compared to the transient heat transfer model,the coupled heat and moisture transfer model incorporating dynamic WDR boundary exhibits maximum increases of 17.6%and 16.2%in cooling and heating loads,respectively.The dynamic WDR boundary conditions provide more precise numerical values for surface moisture flux,offering valuable insights for the thermal design of building enclosures and load calculations for HVAC systems.
文摘Due to the large eddy currents at the ends of the quadrupole magnets for CSNS/RCS, the magnetic field properties and the heat generation are of great concern. In this paper, we take transient electromagnetic simulation and make use of the eddy current loss from the transient electromagnetic results to perform thermal analysis. Through analysis of the simulated results, the magnetic field dynamic properties of these magnets and a temperature rise are achieved. Finally, the accuracy of the thermal analysis is confirmed by a test of the prototype quadrupole magnet of the RCS.
基金This work was supported by the National Basic Research Program of China (No. 2013CB228402) and the National Natural Science Foundation of China (Grant No. 50976046).
文摘In order to alleviate the pressure of experi- mental research of turbocharged diesel engine under transient operations, a whole process simulation platform for turbocharged diesel engine under transient operations was established based on the multi-software coupling technologies of Matlab/Simulink, GT-Power, STAR-CD and artificial neural network. Aimed at the contradiction of NOx and soot emission control with exhaust gas recirculation (EGR) of turbocharged diesel engine under transient operations, on this simulation platform, a transient EGR valve control strategy was proposed, which adjusted the EGR valve in adjacent level based on the feedback of its opening according soot control limit under transient operations. Simulation and experimental results prove that the transient emission optimization effect of this control strategy is obvious. On the one hand, compared with the previous control strategy, which closed the EGR valve during the whole transient operations, soot emission is slightly increased by 9.5%, but it is still 9% lower than the control limit. On the other hand, compared with the previous control strategy, NOx transient emission is reduced by 44%.
基金co-supported by the Innovation Foundation of Beihang University for Ph.D. Graduatesthe National Natural Science Foundation of China (No. 51206007)
文摘The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.
基金supported in part by the National Key Technology Research and Development Program of China(2013BAAOlB03)in part by the National Natural Science Foundation of China(51261130473).
文摘Effective model reduction methods are required to deal with new challenges in active distribution network simulations that are on a large scale and have complicated structures.In the development of advanced electromagnetic transient simulation programs,automated model reduction plays an important role.This paper proposes an automated realization algorithm for the Krylov subspace based model reduction methods of an active distribution network with which the reduced model can be automatically established according to a given threshold of reduction error.The combined state-space nodal analysis framework is employed to apply the automated model reduction algorithm in popular EMTP-type simulation programs.Simulations are performed using PSCAD and a self-developed program to show the feasibility and validity of the proposed methods.
基金supported by the National Natural Science Foundation of China(51609212,51606167,51779226 and 51976193)。
文摘The gas-liquid two-phase flow patterns of a centrifugal pump during the self-priming process were investigated numerically and experimentally.The Euler-Euler multiphase model and SST k-ω turbulence model were applied for simulating the self-priming process.Meanwhile,the changes of motor speed and self-priming height were considered in the simulation.The overall transient two-phase flow features and water level distributions were mapped.Results showed that the self-priming process was divided into three stages.The liquid level in inlet-pipe rose in oscillation during self-priming process.The variations of water level during self-priming process of numerical simulation and test result agreed well.The inlet-pipe(Ver)was filled at 22 s and 24 s respectively numerically and experimentally.The bubble cloud circulated in the volute during middle stage of self-priming process,and breakup into smaller bubbles by shear force and tongue,and then discharged into chamber.The bubbles in the outlet-pipe mainly included bubbly flow and slug flow at the last stage of self-priming process,which is morphologically consistent with the test results.Also,during the self-priming process,the reflux liquid was pressed by blades and fully mixed with gas;that is the way to realizing the function of self-priming.
基金supported by the National Natural Science Foundation of China(Nos.61604137,61674130)
文摘Trap-induced current collapse has become one of the critical issues hindering the improvement of Ga Nbased microwave power devices. It is difficult to study the behavior of each trapping effect separately with the experimental measurement. Transient simulation is a useful technique for analyzing the mechanism of current collapse. In this paper, the coeffect of surface-and bulk-trapping behaviors on the performance of Al Ga N/Ga N HEMTs is investigated based on the two-dimensional(2 D) transient simulation. In addition, the mechanism of trapping effects is analyzed from the aspect of device physics. Two simulation models with different types of traps are used for comparison, and the simulated results reproduced the experimental measured data. It is found that the final steady-state current decreases when both the surface and bulk traps are taken into account in the model.However, contrary to the expectation, the total current collapse is dramatically reduced(e.g. from 18% to 4% for the 90 nm gate-length device). The results suggest that the surface-related current collapse of Ga N-based HEMTs may be mitigated in some degree due to the participation of bulk traps with short time constant. The work in this paper will be helpful for further optimization design of material and device structures.
文摘Half-wavelength AC Transmission(HWACT)can improve capability of AC transmission significantly.According to the basic principle of HWACT,the electromagnetic transient model of HWACT is built to analyze the fault transient process of transmission line.Based on fault characteristics of HWACT,the adaptability of traditional protections for transmission lines is analyzed briefly,such as current differential protection,distance protection and over current protection.In order to solve the problems of conventional protection caused by HWACT,a novel integrated protection based on multi-frequency domain information is proposed in this paper,which uses both the power frequency information and transient information.The integrated protection based on multi-frequency domain information takes advantages of power frequency and transient protections,which can not only improve the performance of traditional protection of AC transmission line but also realize fast fault judgment by transient travelling wave protection.
基金The work was supported by the National ScienceTechnical Committee in China (85-913-02-05)+1 种基金Climate Prediction Program the National Postdocter Fund.
文摘In this paper,experiment results about East Asia climate from five CGCMs are described.The ability of the models to simulate present climate and the simulated response to increased carbon dioxide are both covered.The results indicate that all models show substantial changes in climate when carbon dioxide concentrations are doubled.In particular,the strong surface warming at high latitudes in winter and the significant increase of summer precipitation in the monsoon area are produced by all models.Regional evaluation results show that these five CGCMs are particularly good in simulating spatial distribution of present climate.The main characteristics of the seasonal mean H500,SAT, MSLP field can be simulated by most CGCMs.But there are significant systematic errors in SAT, MSLP,HS00 fields in most models.On the whole,DKRZ OPYC is the best in simulating the present climate in East Asia.
基金Key Programme (GrantNo. 11875270) and Major Research Plan (Grant No. U1832210).
文摘Background Indirect cooling method is an alternative scheme for magnetic alloy(MA)-loaded cavity because of the feasible structure and MA core treatment process.Stable and long-term operation is not possible without a powerful cooling system for the high-power MA cavity.Purpose The paper reports a method to evaluate the cooling efficiency of an indirect cooling structure for high-power-loss MA cavity.Methods Two types of helix metallic cooling plate were designed and checked by CFX code considering the average power loss more than 0.13 W/cc.In order to enhance the heat-transfer efficiency between the non-flatness surface of the MA core and metallic cooling plate,a filling material with high thermal conductivity is needed.Different commercial filling materials were investigated,and a high-power test bench was developed to assess the cooling efficiency.A parametric fitting method was adopted to qualify the heat-transfer coefficient according to the temperature rising curve.Conclusion The results indicate that the experimental data maintain good consistency with the CFX simulation results and the cooling structure meets the high-power-loss cooling requirement.The heat-transfer capability of the filling was influenced by the thickness of heat-transfer materials and the painting process.The heat-transfer performance of the thermal grease is better than that of the thermal gasket even though the latter has a higher thermal conductivity.The virtual thermal conductivity of the filling material was less than the product index and affirmed by the CFX transient simulation.