The objective of this work was to determine the optimum size and amount of raw materials which influence the viscosity of ceramic paste using the experimental design for the production of tubular support by the extrus...The objective of this work was to determine the optimum size and amount of raw materials which influence the viscosity of ceramic paste using the experimental design for the production of tubular support by the extrusion technique and its application in microfiltration. The Box Behnken design was used to optimize the viscosity of the ceramic paste. ANOVA was used to model the system represented by independent parameters and dependent output response and to optimize the system by estimating the statistical parameters. A three-factor and three-level design was used generating thus 15 experiments. The independent factors were the amount of porogen, size of porogen and amount of binder and dependent factor the viscosity of the ceramic paste. The minimum (−1), intermediate (0) and maximum (+1) level of the amount of porogen, size of porogen and amount of binder used were 20 g, 30 g and 40 g, 50 μm, 100 μm and 150 μm, and 2 g, 3.5 g and 5 g respectively. The statistical analyses showed that the values of the answers would adapt to a second degree polynomial model. The R-square value obtained was greater than 95%, the Biais factor was equal to the unit and the Absolute Average Deviation (AAD) equal to the zero thus validating the model. The optimal size of raw material was found to be 100 μm for an amount of clay of 66 g, amount of porogen of 30 g and amount of binder of 4 g. The optimum viscosity of the ceramic paste was found to be 26.7 Pa∙s which is close to the viscosity of the clay paste only found to be 28.5 Pa∙s, thus good for shaping by the extrusion technique. The ceramic paste showed a pseudo-plastic behavior. The tubular porous support was sintered at 950°C and the dimensions, such as outer and inner diameters and length of the tube were 4 cm, 2 cm, and 19 cm, respectively. The sintered membrane possesses a porosity of 43.5%, water permeability of 244.9 L/h∙m2 bar, an average pore size of 2.4 μm and mechanical strength of 9.2 MPa with very good corrosion resistance in acidic and basic conditions. The membrane was subjected to microfiltration of synthetic clay suspension at various combinations of applied pressures (0.5 - 2 bar) with a feed concentration of 100 NTU. An increase in the applied pressure leads to an increase in the flow rate and retention rate. The flow rate decreases steadily with time. The highest retention was obtained at 2 bar with permeability of 184.69 L/h∙m2 bar and a retention of 96% decreasing the turbidity to about 3.5 NTU which is below the acceptable value of 5 NTU.展开更多
Porous ceramics usually require high mechanical strength and maximized porosity simultaneously,while for conventional particle grading strategies,it is highly challenging to meet both demands.To this end,a reverse par...Porous ceramics usually require high mechanical strength and maximized porosity simultaneously,while for conventional particle grading strategies,it is highly challenging to meet both demands.To this end,a reverse particle grading strategy was developed based on the linear packing model by unusually introducing coarse particles(d_(50)=16μm)into a fine particle(d50=5μm)matrix.Following the extrusion and sintering process,tubular porous SiC ceramic supports with improved mechanical strength were successfully fabricated.The effects of coarse particles on the rheological properties of the ceramic paste and the macroscopic properties and microstructure of the SiC supports were systematically investigated.With an increase in the content of coarse SiC particles to 30 wt%,the pressure generated during extrusion decreased from 5.5±0.2 to 1.3±0.1 MPa.Notably,the bending strength of the tubular supports increased from 36.6±5.6 to 49.1±4.5 MPa when 20 wt%coarse powder was incorporated.The notably improved mechanical strength was attributed to the distribution of coarse particles that prolonged the route of crack deflection.Additionally,the optimized tubular supports had an average pore size of 1.2±0.1μm,an open porosity of 45.1%±1.6%,and a water permeability of 7163±150 L/(m^(2)·h·bar)as well as good alkali and acid corrosion resistance.Significantly,the strategy was proven to be feasible for the scale-up fabrication of 19-channel SiC tubular porous ceramic supports.展开更多
文摘The objective of this work was to determine the optimum size and amount of raw materials which influence the viscosity of ceramic paste using the experimental design for the production of tubular support by the extrusion technique and its application in microfiltration. The Box Behnken design was used to optimize the viscosity of the ceramic paste. ANOVA was used to model the system represented by independent parameters and dependent output response and to optimize the system by estimating the statistical parameters. A three-factor and three-level design was used generating thus 15 experiments. The independent factors were the amount of porogen, size of porogen and amount of binder and dependent factor the viscosity of the ceramic paste. The minimum (−1), intermediate (0) and maximum (+1) level of the amount of porogen, size of porogen and amount of binder used were 20 g, 30 g and 40 g, 50 μm, 100 μm and 150 μm, and 2 g, 3.5 g and 5 g respectively. The statistical analyses showed that the values of the answers would adapt to a second degree polynomial model. The R-square value obtained was greater than 95%, the Biais factor was equal to the unit and the Absolute Average Deviation (AAD) equal to the zero thus validating the model. The optimal size of raw material was found to be 100 μm for an amount of clay of 66 g, amount of porogen of 30 g and amount of binder of 4 g. The optimum viscosity of the ceramic paste was found to be 26.7 Pa∙s which is close to the viscosity of the clay paste only found to be 28.5 Pa∙s, thus good for shaping by the extrusion technique. The ceramic paste showed a pseudo-plastic behavior. The tubular porous support was sintered at 950°C and the dimensions, such as outer and inner diameters and length of the tube were 4 cm, 2 cm, and 19 cm, respectively. The sintered membrane possesses a porosity of 43.5%, water permeability of 244.9 L/h∙m2 bar, an average pore size of 2.4 μm and mechanical strength of 9.2 MPa with very good corrosion resistance in acidic and basic conditions. The membrane was subjected to microfiltration of synthetic clay suspension at various combinations of applied pressures (0.5 - 2 bar) with a feed concentration of 100 NTU. An increase in the applied pressure leads to an increase in the flow rate and retention rate. The flow rate decreases steadily with time. The highest retention was obtained at 2 bar with permeability of 184.69 L/h∙m2 bar and a retention of 96% decreasing the turbidity to about 3.5 NTU which is below the acceptable value of 5 NTU.
基金the financial support provided by the National Key R&D Program of China(No.2022YFB3805002)the National Natural Science Foundation of China(No.22308150)+5 种基金Jiangsu Provincial Department of Science and Technology(No.BK20232010)the Research Programs of the Science and Technology of Guangxi Zhuang Autonomous Region(No.GUIKE-AA22117015-1)the Natural Science Foundation of Jiangsu Province(No.BK20220345)the Key R&D Program of Jiangsu Province(No.BE2023360)the Key R&D Project of Nanjing Jiangbei New Area(No.ZDYF202203)the Youth Science and Technology Talents Lifting Project of Jiangsu Association of Science and Technology(No.105019ZS_007).
文摘Porous ceramics usually require high mechanical strength and maximized porosity simultaneously,while for conventional particle grading strategies,it is highly challenging to meet both demands.To this end,a reverse particle grading strategy was developed based on the linear packing model by unusually introducing coarse particles(d_(50)=16μm)into a fine particle(d50=5μm)matrix.Following the extrusion and sintering process,tubular porous SiC ceramic supports with improved mechanical strength were successfully fabricated.The effects of coarse particles on the rheological properties of the ceramic paste and the macroscopic properties and microstructure of the SiC supports were systematically investigated.With an increase in the content of coarse SiC particles to 30 wt%,the pressure generated during extrusion decreased from 5.5±0.2 to 1.3±0.1 MPa.Notably,the bending strength of the tubular supports increased from 36.6±5.6 to 49.1±4.5 MPa when 20 wt%coarse powder was incorporated.The notably improved mechanical strength was attributed to the distribution of coarse particles that prolonged the route of crack deflection.Additionally,the optimized tubular supports had an average pore size of 1.2±0.1μm,an open porosity of 45.1%±1.6%,and a water permeability of 7163±150 L/(m^(2)·h·bar)as well as good alkali and acid corrosion resistance.Significantly,the strategy was proven to be feasible for the scale-up fabrication of 19-channel SiC tubular porous ceramic supports.
