Stress-assisted corrosion mechanism of 3Ni steel by using gradient boosting decision tree machining learning method

Traditional 3Ni weathering steel cannot completely meet the requirements for offshore engineering development,resulting in the design of novel 3Ni steel with the addition of microalloy elements such as Mn or Nb for strength enhancement becoming a trend.The stress-assisted corrosion behavior of a novel designed high-strength 3Ni steel was investigated in the current study using the corrosion big data method.The information on the corrosion process was recorded using the galvanic corrosion current monitoring method.The gradi-ent boosting decision tree(GBDT)machine learning method was used to mine the corrosion mechanism,and the importance of the struc-ture factor was investigated.Field exposure tests were conducted to verify the calculated results using the GBDT method.Results indic-ated that the GBDT method can be effectively used to study the influence of structural factors on the corrosion process of 3Ni steel.Dif-ferent mechanisms for the addition of Mn and Cu to the stress-assisted corrosion of 3Ni steel suggested that Mn and Cu have no obvious effect on the corrosion rate of non-stressed 3Ni steel during the early stage of corrosion.When the corrosion reached a stable state,the in-crease in Mn element content increased the corrosion rate of 3Ni steel,while Cu reduced this rate.In the presence of stress,the increase in Mn element content and Cu addition can inhibit the corrosion process.The corrosion law of outdoor-exposed 3Ni steel is consistent with the law based on corrosion big data technology,verifying the reliability of the big data evaluation method and data prediction model selection.

Nontraditional energy-assisted mechanical machining of difficult-to-cut materials and components in aerospace community:a comparative analysis

The aerospace community widely uses difficult-to-cut materials,such as titanium alloys,high-temperature alloys,metal/ceramic/polymer matrix composites,hard and brittle materials,and geometrically complex components,such as thin-walled structures,microchannels,and complex surfaces.Mechanical machining is the main material removal process for the vast majority of aerospace components.However,many problems exist,including severe and rapid tool wear,low machining efficiency,and poor surface integrity.Nontraditional energy-assisted mechanical machining is a hybrid process that uses nontraditional energies(vibration,laser,electricity,etc)to improve the machinability of local materials and decrease the burden of mechanical machining.This provides a feasible and promising method to improve the material removal rate and surface quality,reduce process forces,and prolong tool life.However,systematic reviews of this technology are lacking with respect to the current research status and development direction.This paper reviews the recent progress in the nontraditional energy-assisted mechanical machining of difficult-to-cut materials and components in the aerospace community.In addition,this paper focuses on the processing principles,material responses under nontraditional energy,resultant forces and temperatures,material removal mechanisms,and applications of these processes,including vibration-,laser-,electric-,magnetic-,chemical-,advanced coolant-,and hybrid nontraditional energy-assisted mechanical machining.Finally,a comprehensive summary of the principles,advantages,and limitations of each hybrid process is provided,and future perspectives on forward design,device development,and sustainability of nontraditional energy-assisted mechanical machining processes are discussed.

On dry machining of AZ31B magnesium alloy using textured cutting tool inserts

Magnesium alloys have many advantages as lightweight materials for engineering applications,especially in the fields of automotive and aerospace.They undergo extensive cutting or machining while making products out of them.Dry cutting,a sustainable machining method,causes more friction and adhesion at the tool-chip interface.One of the promising solutions to this problem is cutting tool surface texturing,which can reduce tool wear and friction in dry cutting and improve machining performance.This paper aims to investigate the impact of dimple textures(made on the flank face of cutting inserts)on tool wear and chip morphology in the dry machining of AZ31B magnesium alloy.The results show that the cutting speed was the most significant factor affecting tool flank wear,followed by feed rate and cutting depth.The tool wear mechanism was examined using scanning electron microscope(SEM)images and energy dispersive X-ray spectroscopy(EDS)analysis reports,which showed that at low cutting speed,the main wear mechanism was abrasion,while at high speed,it was adhesion.The chips are discontinuous at low cutting speeds,while continuous at high cutting speeds.The dimple textured flank face cutting tools facilitate the dry machining of AZ31B magnesium alloy and contribute to ecological benefits.

Field-assisted machining of difficult-to-machine materials

Difficult-to-machine materials (DMMs) are extensively applied in critical fields such as aviation,semiconductor,biomedicine,and other key fields due to their excellent material properties.However,traditional machining technologies often struggle to achieve ultra-precision with DMMs resulting from poor surface quality and low processing efficiency.In recent years,field-assisted machining (FAM) technology has emerged as a new generation of machining technology based on innovative principles such as laser heating,tool vibration,magnetic magnetization,and plasma modification,providing a new solution for improving the machinability of DMMs.This technology not only addresses these limitations of traditional machining methods,but also has become a hot topic of research in the domain of ultra-precision machining of DMMs.Many new methods and principles have been introduced and investigated one after another,yet few studies have presented a comprehensive analysis and summarization.To fill this gap and understand the development trend of FAM,this study provides an important overview of FAM,covering different assisted machining methods,application effects,mechanism analysis,and equipment design.The current deficiencies and future challenges of FAM are summarized to lay the foundation for the further development of multi-field hybrid assisted and intelligent FAM technologies.

Machine learning applications in healthcare clinical practice and research

Machine learning(ML)is a type of artificial intelligence that assists computers in the acquisition of knowledge through data analysis,thus creating machines that can complete tasks otherwise requiring human intelligence.Among its various applications,it has proven groundbreaking in healthcare as well,both in clinical practice and research.In this editorial,we succinctly introduce ML applications and present a study,featured in the latest issue of the World Journal of Clinical Cases.The authors of this study conducted an analysis using both multiple linear regression(MLR)and ML methods to investigate the significant factors that may impact the estimated glomerular filtration rate in healthy women with and without non-alcoholic fatty liver disease(NAFLD).Their results implicated age as the most important determining factor in both groups,followed by lactic dehydrogenase,uric acid,forced expiratory volume in one second,and albumin.In addition,for the NAFLD-group,the 5th and 6th most important impact factors were thyroid-stimulating hormone and systolic blood pressure,as compared to plasma calcium and body fat for the NAFLD+group.However,the study's distinctive contribution lies in its adoption of ML methodologies,showcasing their superiority over traditional statistical approaches(herein MLR),thereby highlighting the potential of ML to represent an invaluable advanced adjunct tool in clinical practice and research.

Non-traditional Machining Techniques for Fabricating Metal Aerospace Filters

Thanks to recent advances in manufacturing technology, aerospace system designers have many more options to fabricate high-quality, low-weight, high-capacity, cost-effective filters. Aside from traditional methods such as stamping, drilling and milling, many new approaches have been widely used in filter-manufacturing practices on account of their increased processing abilities. How- ever, the restrictions on costs, the need for studying under stricter conditions such as in aggressive fluids, the complicity in design, the workability of materials, and others have made it difficult to choose a satisfactory method from the newly developed processes, such as, photochemical machining （PCM）, photo electroforming （PEF） and laser beam machining （LBM） to produce small, inexpensive, lightweight aerospace filters. This article appraises the technical and economical viability of PCM, PEF, and LBM to help engineers choose the fittest approach to turn out aerospace filters.

Aviation-oriented Micromachining Technology—Micro-ECM in Pure Water

This article proposes a precise and ecofriendly micromachining technology for aerospace application called electrochemical machining in pure water （PW-ECM）. On the basis of the principles of water dissociation, a series of test setups and tests are devised and performed under different conditions. These tests explain the need for technological conditions realizing PW-ECM, and further explore the technological principles. The results from the tests demonstrate a successful removal of electrolytic slime by means of ultrasonic vibration of the workpiece. To ensure the stability and reliability of PW-ECM process, a new combined machining method of PW-ECM assisted with ultrasonic vibration （PW-ECM/USV） is devised. Trilateral and square cavities and holes as well as a group of English alphabets are worked out on a stainless steel plate. It is confirmed that PW-ECM will be probably an efficient new aviation precision machining method.

MACHINING OF METAL MATRIX COMPOSITES

Two types of aluminium-based composites reinforced respectively with 20 vol short fibre alumina and with a hybrid of 15 vol SiC particle and 5 vol short alumina fibre are machined with different tool materials:cemented carbide,ceramic,cubic boron nitride(CBN)and polycrystalline diamond(PCD).The analysis on tool wear shows that the various tool materials exhibite different tool wear behaviours,and the tool wear mechanisma are discussed.Apparently,PCD tools do not necessarily guarantee dimensional stability but they can provide the most economic means for machining all sorts of composites.Consequently,a suitable tool material is suggested for machining each metal matrix composite(MMC) from the standpoints of tool wear and machined surface finish.

INTERNET-BASED MACHINING PARAMETER OPTIMIZATION AND MANAGEMENT SYSTEM FOR HIGH-SPEED MACHINING

The theory and its method of machining parameter optimization for high-speed machining are studied. The machining data collected from workshops, labs and references are analyzed. An optimization method based on the genetic algorithm (GA) is investigated. Its calculation speed is faster than that of traditional optimization methods, and it is suitable for the machining parameter optimization in the automatic manufacturing system. Based on the theoretical studies, a system of machining parameter management and optimization is developed. The system can improve productivity of the high-speed machining centers.

Machining Line Planner输出STEP-NC数控程序的研究

介绍了STEP-NC的概念、数据模型及其结构特点,然后通过对比MLP(Machining Line Planner)和STEP-NC数控程序对特征和操作的不同定义方法,分析了在MLP中特征及加工工艺与STEP-NC的对应关系,探讨了在MLP中实现输出STEP-NC格式的零件加工程序的方法。

PRECISION OF HSK TOOLING SYSTEM IN HIGH SPEED MACHINING

Based on the theory of elastic mechanics and material mechanics, the orientation precision of the hohl schaft kegel（HSK） tooling system in static and dynamic states is theoretically and experimentally studied. The relation between the clamping force and the shank taper is obtained. And a proper clamping force is found to be essential to assure the axial and radial orientation precisions of the HSK tooling system in high speed machining （HSM）. Analytical results show that the reason why the HSK tooling system can keep high precision at the high rotational speed is that the actual axial clamping force keeps the two surfaces of the shank and the spindle in contact all the time.

Optimization of micro milling electrical discharge machining of Inconel 718 by Grey-Taguchi method

The optimization of micro milling electrical discharge machining（EDM） process parameters of Inconel 718 alloy to achieve multiple performance characteristics such as low electrode wear,high material removal rate and low working gap was investigated by the Grey-Taguchi method.The influences of peak current,pulse on-time,pulse off-time and spark gap on electrode wear（EW）,material removal rate（MRR） and working gap（WG） in the micro milling electrical discharge machining of Inconel 718 were analyzed.The experimental results show that the electrode wear decreases from 5.6×10-9 to 5.2×10-9 mm3/min,the material removal rate increases from 0.47×10-8 to 1.68×10-8 mm3/min,and the working gap decreases from 1.27 to 1.19 μm under optimal micro milling electrical discharge machining process parameters.Hence,it is clearly shown that multiple performance characteristics can be improved by using the Grey-Taguchi method.

A NEW ALGORITHM BASED ON TRIANGULATION FOR 5 AXIS MACHINING OF SCULPTURED SURFACES

NC machining path of sculptured surfaces in CAD/CAM system plays an important role on manufacture. This paper describes a new algorithm for 5 axis machining of sculptured surfaces and the algorithm is interference free. The approach includes: (1) the tesselation of the parametric surfaces into triangles; (2) building topological relations among triangles;(3) 5 axis tool path generation; (4) interference detection and tool position correction.

PLANNING METHOD OF TOOL ORIENTATION IN FIVE-AXIS NC MACHINING

The planning method of tool orientation in the five-axis NC machining is studied. The problem of the existing method is analyzed and a new method for generating the global smoothing tool orientation is proposed by introducing the key frame idea in the animation-making. According to the feature of the part, several key tool orientations are set without interference between the tool and the part. Then, these key tool orientations are inter- polated by the spline function. By mapping the surface parameter to the spline parameter, the spline function value is obtained and taken as the tool orientation when generating the CL file. The machining result shows that the proposed method realizes the global smoothing of the tool orientation and the continuity of the rotational speed and the rotational acceleration. It also avoids the shake of the machine tool and improves the machining quality.

IMPROVEMENT OF MACHINING ACCURACY OF CANTILEVER BORING BAR SYSTEM USING PIEZOELECTRIC ACTUATOR

This paper is concerned with the work involved in improving the machining accuracy of a cantilever boring bar by on line compensation with a piezoelectric actuator. A boring bar is made into lever structure, with strain gauges attached to the bar for measuring its force induced deflections. The piezoelectric actuator is employed to compensate the deflections of the boring bar for accuracy improvement. Due to the mechanical advantage of the structure, the boring bar can be made into smaller size. The diameter of the bar implemented is 10 mm and the ratio of length to diameter (L/D) is larger than 8. It is found that the machining accuracy is improved considerably by using the piezoelectric actuator compensation system.

A Definition Formalism of Machining Features for DFM

Benefiting from advances in feature technology for design and manufacture can not be expected before a formal methodology is established. This paper makes attempt to establish a definition formalism of machining features in design for manufacturability from two aspects: formal definition and manufacturability analysis. Some definitions for machining feature based upon the selection and sequencing of material removal operations for component in accordance with the design geometry are presented and a framework of feature based design for manufacturability is outlined correspondingly. The proposed scheme contributes to several aspects of feature based CAD/CAM integration, especially to encourage potentially a more generic approach to the automation of design.

Monitoring Computer Numerical Control Machining Progress Based on Information Fusion

To cope with the market demand dynamically,enterprise needs to obtain the production status of work in process real-timely,but the information of machining progress has feature of uncertainty and can not reflect the status of production field effectively.In this work,to overcome the ineffectiveness of computer numerical control(CNC) machining progress information extraction and its application restriction in practice because of heterogeneous system of CNC machine,based on information fusion by analyzing multi-sources information,estimating CNC machining status and predicting the machining progress through tracking tool coordinates,a CNC machining progress monitoring method is presented.The multi-sources heterogeneous information includes machining path,real-time spindle power information,manual input data and tool position.On the method of obtaining this multi-sources heterogeneous information,the method which helps explore numerical control(NC) program,monitor spindle power of CNC,collect human-computer interaction(HCI) information,obtain real-time tool coordinates and express the knowledge concerned in this field is analyzed; The decision rule of CNC machining status in the way of fusing multi-sources information in manufacturing process is summarized,as well as the machining progress tracking method in accordance with real-time tool coordinates and machining path is presented.Finally,the method discussed is proved feasible by the verification of machining progress tracking through simulation experiment.The proposed research realizes the effective integration of CNC machining progress information,and enables enterprises an efficient way to share CNC information and configure CNC resources optimally.

Smart Cutting Tools and Smart Machining: Development Approaches, and Their Implementation and Application Perspectives

Smart machining has tremendous potential and is becoming one of new generation high value precision manufacturing technologies in line with the advance of Industry 4.0 concepts. This paper presents some innovative design concepts and, in particular, the development of four types of smart cutting tools, including a force-based smart cutting tool, a temperature-based internally-cooled cutting tool, a fast tool servo （FTS） and smart collets for ultra- precision and micro manufacturing purposes. Implemen- tation and application perspectives of these smart cutting tools are explored and discussed particularly for smart machining against a number of industrial application requirements. They are contamination-free machining, machining of tool-wear-prone Si-based infra-red devices and medical applications, high speed micro milling and micro drilling, etc. Furthermore, implementation tech- niques are presented focusing on： （a） plug-and-produce design principle and the associated smart control algo- rithms, （b） piezoelectric film and surface acoustic wave transducers to measure cutting forces in process, （c） critical cutting temperature control in real-time machining, （d） in- process calibration through machining trials, （e） FE-based design and analysis of smart cutting tools, and （f） applica- tion exemplars on adaptive smart machining.

Convergence Analysis of the Numerical Solution for Cathode Design of Aero-engine Blades in Electrochemical Machining

As a main difficult problem encountered in electrochemical machining （ECM）, the cathode design is tackled, at present, with various numerical analysis methods such as finite difference, finite element and boundary element methods. Among them, the finite element method presents more flexibility to deal with the irregularly shaped workpieces. However, it is very difficult to ensure the convergence of finite element numerical approach. This paper proposes an accurate model and a finite element numerical approach of cathode design based on the potential distribution in inter-electrode gap. In order to ensure the convergence of finite element numerical approach and increase the accuracy in cathode design, the cathode shape should be iterated to eliminate the design errors in computational process. Several experiments are conducted to verify the machining accuracy of the designed cathode. The experimental results have proven perfect convergence and good computing accuracy of the proposed finite element numerical approach by the high surface quality and dimensional accuracy of the machined blades.

Study on Machining Deformation of Aircraft Monolithic Component by FEM and Experiment

Machining deformation of aircraft monolithic component is simulated by finite element method （FEM） and validated by experiment. The initial residual stress in pre-stretched plate is generated by simulating quenching and stretching processes. With a single tool-tooth milling process FEM, the machining loads in monolithic component material removing is obtained. Restart-calculation is put forward to complete the whole simulation of machining process. To verify the FEM result, an experiment is carried out. The deformation distribution of the monolithic component resulting from FEM shows a good agreement with the experiment result, which indicates that the key technologies presented in the paper are practicable and can be used to simulate the milling process of monolithic component to predict its deformation. Lengthy and expensive trial and error experiment process can be avoided.