Effects of ion-exchange on the pervaporation performance and microstructure of NaY zeolite membrane

Pervaporation performance of NaY zeolite membranes is improved by ion-exchange with di-valent nitrate salt.Different nitrate salts,including Co(NO_(3))_(2),Mg(NO_(3))_(2),Zn(NO_(3))_(2),Ca(NO_(3))_(2),Cu(NO_(3))_(2),KNO_(3),and AgNO_(3),have great effects on the channel structure and water affinity of the NaY zeolite membrane.When the concentration of nitrate salt,ion-exchange temperature and time are 0.1 mol·L^(-1),50℃and 2 h,the ion-exchange degree order of NaY zeolites is Ag^(+)>K^(+)>Ca^(2+)>Zn^(2+)>>Co^(2+)>Mg^(2+).Especially,Ag^(+)and K^(+)cation exchange degree of NaY zeolites are achieved to 96.54% and 82.77% in this work.BET surface,total pore capacity,pore size distribution and water contact angle of the ion-exchanged NaY zeolites are all disordered by mono-and di-valent cations.Di-valent nitrate salt is favor for increasing the dehydration performance of NaY zeolite membranes by ion-exchange.When the ion-exchange solution is Zn(NO_(3))_(2),the total flux variation and separation factor variation of the NaY membrane(M-5)are -45% and 230% for separation of 10%(mass)H_(2)O/EtOH mixture by pervaporation,and the ion-exchanged membranes showed good reproducibility.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells.The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs.In this work,we adopted a solid-liquid two-step film formation technique,which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films.This method possesses the advantages of integrating vapor deposition and solution methods,which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform,large-area perovskite film.Furthermore,modification of the NiO_(x)/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization.As a result,a large-area perovskite film possessing larger grains,fewer pinholes,and reduced defects could be achieved.The inverted PSM with an active area of 61.56 cm^(2)(10×10 cm^(2)substrate)achieved a champion power conversion efficiency of 20.56%and significantly improved stability.This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

A new two-step variational model for multiplicative noise removal with applications to texture images

Multiplicative noise removal problems have attracted much attention in recent years.Unlike additive noise,multiplicative noise destroys almost all information of the original image,especially for texture images.Motivated by the TV-Stokes model,we propose a new two-step variational model to denoise the texture images corrupted by multiplicative noise with a good geometry explanation in this paper.In the first step,we convert the multiplicative denoising problem into an additive one by the logarithm transform and propagate the isophote directions in the tangential field smoothing.Once the isophote directions are constructed,an image is restored to fit the constructed directions in the second step.The existence and uniqueness of the solution to the variational problems are proved.In these two steps,we use the gradient descent method and construct finite difference schemes to solve the problems.Especially,the augmented Lagrangian method and the fast Fourier transform are adopted to accelerate the calculation.Experimental results show that the proposed model can remove the multiplicative noise efficiently and protect the texture well.

Two-step growth of β-Ga_(2)O_(3) on c-plane sapphire using MOCVD for solar-blind photodetector

In this work,a two-step metal organic chemical vapor deposition(MOCVD)method was applied for growingβ-Ga_(2)O_(3) film on c-plane sapphire.Optimized buffer layer growth temperature(T_(B))was found at 700℃ and theβ-Ga_(2)O_(3) film with full width at half maximum(FWHM)of 0.66°was achieved.A metal−semiconductor−metal(MSM)solar-blind photodetector(PD)was fabricated based on theβ-Ga_(2)O_(3) film.Ultrahigh responsivity of 1422 A/W@254 nm and photo-to-dark current ratio(PDCR)of 10^(6) at 10 V bias were obtained.The detectivity of 2.5×10^(15) Jones proved that the photodetector has outstanding performance in detecting weak signals.Moreover,the photodetector exhibited superior wavelength selectivity with rejection ratio(R_(250 nm)/R_(400 nm))of 105.These results indicate that the two-step method is a promising approach for preparation of high-qualityβ-Ga_(2)O_(3)films for high-performance solar-blind photodetectors.

Effect of two-step solid solution on microstructure andδphase precipitation of Inconel 718 alloy

Inconel 718 is the most popular nickel-based superalloy and is extensively used in aerospace,automotive,and energy indus-tries owing to its extraordinary thermomechanical properties.The effects of different two-step solid solution treatments on microstructure andδphase precipitation of Inconel 718 alloy were studied,and the transformation mechanism fromγ″metastable phase toδphase was clarified.The precipitates were statistically analyzed by X-ray diffractometry.The results show that theδphase content firstly increased,and then decreased with the temperature of the second-step solid solution.The changes in microstructure andδphase were studied by scanning electron microscopy and transmission electron microscopy.An intragranularδphase formed in Inconel 718 alloy at the second-[100]_(δ)[011]γ step solid solution temperature of 925℃,and its orientation relationship withγmatrix was determined as//and(010)_(δ)//(111)γ.Furthermore,the Vickers hardness of different heat treatment samples was measured,and the sample treated by second-step solid solution at 1010℃ reached the maximum hardness of HV 446.84.

Purification of Lactic Acid by Heterogeneous Catalytic Distillation Using Ion-exchange Resins

The purification of lactic acid based on the esterification of raw lactic acid from fermentation broth and then the catalytic distillation hydrolysis of methyl lactate simultaneously to achieve pure lactic acid is reported. The esterification kinetics of lactic acid with methanol catalyzed by strong-acid cation-exchange resins (Amberlyst-15,D001, D002, NKC, 002) was studied under the condition that simulates the real catalytic environment. Experimental results were correlated by a Langmuir-Hinselwood model and the nonideality of the solution was taken into account by using activities calculated by the universal quasichemical functional group activity coefficient (UNIFAC) method.A good agreement between the model and the experimental data was achieved. Continuous purification experiments were conducted to find the optimum column configuration and operation condition for the system. The effects of various parameters, e.g. the length of different section of the column, feed rate and ratio of reactants, packing material and catalyst type, were studied. This novel system shows good separation results in lab scale, and is potential for industrial application.

Effective adsorptive denitrogenation from model fuels over yttrium ion-exchanged Y zeolite

The adsorption removal of indole and quinoline in octane with and without toluene over zeolites NaY and Yttrium Ion-exchanged Y(YY)using batch adsorption experiments was studied at 25℃and 0.1 MPa.YY was prepared by treating NaY with Y(NO3)3 solution twice via liquid ion-exchange method.NaY and YY were both characterized by XRD,SEM,N2 adsorption,XRF,NH3-TPD,and pyridine-FTIR techniques.Adsorption isotherms of indole,quinoline and toluene in octane were conducted at 25.0℃to explain the influence of toluene on nitrogen removal over NaY and YY.The partial destruct of the crystalline structure of NaY was observed after the introduction of yttrium ion,which led to an evident decline in BET surface area and pore volume of YY.Strong Br?nsted acidity and medium Lewis acidity were introduced by yttrium ion-exchange.Though the specific surface area and pore volume of YY were much lower than those of NaY,YY exhibited equivalent adsorption capacities for indole and quinoline as NaY in model fuels without toluene.In the presence of 20 vol%toluene,however,YY exhibited much higher adsorption capacities for indole and quinoline than NaY,especially in the case of quinoline.The improved toluene-tolerant of YY was ascribed to the strong acid–base interaction between YY and quinoline and the decreased adsorption strength between YY and toluene.

Tribological Properties of Magnesium Ion-exchanged α-Zirconium Phosphate as a Solid Lubricant Additive in Lithium Grease

Magnesium ion-exchanged a-zirconium phosphates(Mg-α-ZrP) with particle sizes of 600 and 80 nm were prepared through the sealed ion-exchange and one-step hydrothermal synthesis methods, respectively. It was found that larger particles of Mg-α-ZrP had a higher load-carrying capacity than that of smaller particles, whereas smaller Mg-α-ZrP particles had better anti-wear properties than that of larger Mg-α-ZrP particles under mild loads. The correlation between the particle size of the sample and the surface roughness of the friction pair thus seems to be a key factor influencing the performance.

Tungsten removal from molybdate solutions using chelating ion-exchange resin:Equilibrium adsorption isotherm and kinetics

The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the adsorption process of W obeys the Freundlich model very well whereas the exchange process with Mo approximately follows the Henry model.The kinetic experiments show that the intraparticle diffusion process was the rate-determining step for W sorption on the resin,and the corresponding activation energy is calculated to be 21.976 k J/mol.

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl_4 and SbCl_3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using： （1） an ion-exchange hydrolysis to remove chlorine ions, and （2） isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.

Study on Removal of Trace Lead from Nickel Sulphate Solution by Ion-exchange Method

By comparing the adsorption capacity of several kinds of resins, D363 resin is regarded as the most suitable one for removing lead from nickel sulphate electrolyte. The effects of pH, temperature and contact time on exchange adsorption during removing trace lead from industrial nickel sulphate solution with D363 large pore weak alkali anion exchange resin are discussed. Optimum conditions of adsorption of lead from nickel electrolyte by D363 resin are at room temperature, pH 1 2, contact time 30 min.

Influence of earth gravity on reaction engineering of tubular reactor for high concentration tungsten ion-exchange

The influence of gravity on the reaction engineering of tubular reactor is studied by analyzing the residence time distribution curves.The results show that upflow-feeding mode is more beneficial compared with downflow-feeding mode,since the flow pattern of the fluid in the reactor is closer to plug flow.The result of dynamic experiment conducted in ion-exchange of tungsten metallurgy is as good as that in reaction engineering of ion-exchange column.Whether downflow-feeding or upflow-feeding mode is adopted,breakthrough time decreases when solution concentration increases.Upflow-feeding mode has longer breakthrough time and greater improvement in adsorption capacity especially with high WO3 concentration in ion-exchange.

Investigation of the Ion-Exchange Behavior of Zeolite Y in the Presence of Resin

Ion-exchange process of zeolite Y using ammonium-type resin as an exchange reagent was successfully carried out. The effect of temperature, space velocity and ion concentration on the breakthrough curves was carefully investigated. At the first exchange section, the maximum proportion of qualified zeolites(QR) was obtained at a temperature of 70 ℃, a weight hourly space velocity of 0.61 h-1, and an ion concentration of 197 mg/L. The minimum length of mass-transfer zone(MTZ) of the resin bed was achieved at a temperature of 70 ℃, a space velocity of 0.61 h-1, and an ion concentration of 423 mg/L. At the second exchange section, the length of MTZ of the resin bed was significantly increased, and the exchange of Na+ ions contained in zeolite Y was more difficult than that achieved at the first exchange section. In both the first and the second exchange sections, the zeolite Y subjected to ion exchange with the resin maintained the similar physical and chemical properties as compared to those exchanged by the conventional approaches, but the zeolite Y, which was obtained after ion exchange, contained a significantly lower content of Na2 O.

Redistributing Cu species in Cu-SSZ-13 zeolite as NH3-SCR catalyst via a simple ion-exchange

The nature and distribution of Cu species in Cu-SSZ-13 play a vital role in selective catalytic reduction of NO by NH3(NH3-SCR),but existing methods for adjusting the Cu distribution are complex and difficult to control.Herein,we report a simple and effective ion-exchange approach to regulate the Cu distribution in the one-pot synthesized Cu-SSZ-13 that possesses sufficient initial Cu species and thus provides a“natural environment”for adjusting Cu distribution precisely.By using this proposed strategy,a series of Cu-SSZ-13x zeolites with different Cu contents and distributions were obtained.It is shown that the dealumination of the as-synthesized Cu-SSZ-13 during the ion-exchange generates abundant vacant sites in the double six-membered-rings of the SSZ-13 zeolite for relocating Cu2+species and thus allows the redistribution of the Cu species.The catalytic results showed that the ion-exchanged Cu-SSZ-13 zeolites exhibit quite different catalytic performance in NH3-SCR reaction but superior to the parent counterpart.The structure–activity relationship analysis indicates that the redistribution of Cu species rather than other factors(e.g.,crystallinity,chemical composition,and porous structure)is responsible for the improved NH3-SCR performance and SO_(2) and H_(2)O resistance.Our work offers an effective method to precisely adjust the Cu distribution in preparing the industrial SCR catalysts.

Effect of Mg^(2+) content in ion-exchanged Shengli lignite on its equilibrium adsorption water content and its mechanism

Mg ion-exchanged samples were prepared with acid-washed Shengli lignite.The chemical composition of the ash of the raw sample was determined by X-ray fluorescence.The equilibrium adsorption water contents of samples were determined in a range of relative humidity.The ion-exchange process was characterized by FT-IR,ash content,and p H value.A possible mechanism is proposed for equilibrium adsorption water of ion-exchanged samples at different humidities.The extent of ion-exchange reaction between Mg2+and lignite is controlled by the concentration of Mg2+in Mg SO4solution.The effect of Mg2+on equilibrium adsorption water content varies with relative humidity and content of Mg2+.The factor that controls equilibrium adsorption water content at low relative humidity is water interactions with sorption sites,which are Mg2+–carboxyl group complex.At middle relative humidity capillary force between Mg2+–water clusters Mg+(H2O)nand capillary is more important.At high relative humidity,free water–free water interactions are more significant.

Synthesis and Characterization of Ion-exchange Sulfonated Poly (ether sulfone)

N,N＇-Bis（3-hydroxyphenyl）-1,8,4,5-naphthalenetetracarboxylic bisimide was prepared from the reaction of 1,8,4,5-naphthalenetetrcarboxylic acid dianhydride and 2-aminophenol in N, N-dimethylformamide. Polymerization of this bisimide with 4,4＇-difluorodiphenylsulfone and disodium 3,3＇-disulfonate4,4＇-difluorodiphenylsulfone gave ion-exchange sulfonated poly（ether sulfone）. The structure of the title compound was characterized with H-NMR and its polymer was characterized with FT-IR.

Modified DIX model for ion-exchange equilibrium of L-phenylalanine on a strong cation-exchange resin

L-phenylalanine, one of the nine essential amino acids for the human body, is extensively used as an ingredient in food, pharmaceutical and nutrition industries. A suitable equilibrium model is required for purification of L-phenylalanine based on ion-exchange chromatography. In this work, the equilibrium uptake of L-phenylalanine on a strong acid-cation exchanger SH11 was investigated experimentally and theoretically. A modified Donnan ion-exchange （DIX） model, which takes the activiW into account, was established to predict the uptake of L-phenylalanine at various solution pH values. The model parameters including selectivity and mean activity coefficient in the resin phase are presented. The modified DIX model is in good agreement with the experimental data. The optimum operating pH value of 2.0, with the highest t-phenylalanine uptake on the resin, is predicted by the model. This basic information combined with the general mass transfer model will lay the foundation for the prediction of dynamic behavior of fixed bed separation process.

Research on changes of hydrodynamics and ion-exchange adsorption in Brackish-Water Interface

In light of multiple field experiments in typical tidal areas with active sea-land interaction, corresponding analysis through hydrodynamic simulation and of ion composition evolution all insist on following conclusions. Due to the tide, the groundwater level is basically in line with its level but with a slight lag. Moreover, smaller amplitude of such changes were always accompanied by greater distance from shores. In this paper, two salt-freshwater interfaces were identified, namely, a large wedge-shaped interface and an inverted U-shaped one located at K5 (monitoring point). The critical hydraulic gradient of saltwater intrusion was between 0.0345 and 0.0377. Apart from that, mathematical and physical models were adopted to measure the influence of tides, showing a inverse proportion to the hydraulic gradient In addition, characteristics of ionic components can prove that K^+ was adsorbed and Ca^2+ was displaced during saline intrusion, while a reverse process was witnessed during desalting. In summary, cation exchange adsorption plus other complex physical chemical effects would take place during saltwater intrusion.

The Desalting Property of Ion-Exchange Resins in Organic Solvent

the desalting property of ion-exchange resins in organic solventis reported by using potassium acetate as a model compound. Theexperimental results show that solvability of the solvent, stirringspeed, and temperature are the factors which influence theion-exchange rate. The increase of solvability, stirring speed andtemperature will speed up the ion-exchange process.

Purification of a Choleragenoid by Ion-exchange Chromatography

Abstract: Choleragenoid was obtained in pure form by ultra-filteration and fractionation on cationexchange resin-phospho-cellulose column. The choleragenoid was highly pure as judged by the electrophoresis of isoelectric focusing,immunization and SDS-gel electrophoresis.The results of test are thesame as that of the standard choleragenoid.Keywoeds:choleragenoid; vibrio cholerae; purification;ion-exchange; chromatography