Mechanical model for controlling floor heave in deep roadways with U-shaped steel closed support

Open U-shaped steel arch supports are commonly used in large-section static-pressure roadways in coal mines that are more than 900 m deep;however,it is very difficult to control floor heave of roadways.In this paper,a U-shaped steel closed support with an inverted U-shaped steel arch in the floor is proposed as a method for improving the support effect of the surrounding rock during the process of floor heaving.This research established a mechanical model for the U-shaped steel closed support,and determined the reaction forces at the connection of a camber angle.Using the limit load method calculated the critical buckling load of the inverted U-shaped steel arch,and use of a strength check method tested the strength of the U-shaped steel material.A numerical simulation was conducted using the finite difference software FLAC3 D.The simulation results show that the U-shaped steel closed support is able to control the floor heave of roadways,which is successfully used in the West 11-2 development roadway of the Zhuji Mine in the Huainan mining area in China.The cumulative floor heave over two years was less than50 mm.

Mechanical property of U-Shaped 65Mn steel bumpers for seismic base isolation

This study proposes a novel U-shaped 65Mn steel bumper as the displacement restraining device for base-isolated structures with laminated elastomeric rubber bearings.A series of bumpers with different geometric parameters were designed and tested under monotonic and cyclic quasi-static loading protocols.The experimental results from a total of 232 specimens were analyzed to develop an analytical model to calculate the backbone curve and the maximum elastic restoring force for U-shaped 65Mn bumpers.Thus,the analytical equations to calculate the elastic,hardening,and unloading stiffness of U-shaped 65Mn bumpers,as well as their maximum elastic restoring force,are validated by using an additional ten groups of bumpers with varying radiuses.These analytical equations can accurately predict the mechanical parameters of U-shaped 65Mn steel bumpers for a design purpose.

A U-Shaped Network-Based Grid Tagging Model for Chinese Named Entity Recognition

Chinese named entity recognition(CNER)has received widespread attention as an important task of Chinese information extraction.Most previous research has focused on individually studying flat CNER,overlapped CNER,or discontinuous CNER.However,a unified CNER is often needed in real-world scenarios.Recent studies have shown that grid tagging-based methods based on character-pair relationship classification hold great potential for achieving unified NER.Nevertheless,how to enrich Chinese character-pair grid representations and capture deeper dependencies between character pairs to improve entity recognition performance remains an unresolved challenge.In this study,we enhance the character-pair grid representation by incorporating both local and global information.Significantly,we introduce a new approach by considering the character-pair grid representation matrix as a specialized image,converting the classification of character-pair relationships into a pixel-level semantic segmentation task.We devise a U-shaped network to extract multi-scale and deeper semantic information from the grid image,allowing for a more comprehensive understanding of associative features between character pairs.This approach leads to improved accuracy in predicting their relationships,ultimately enhancing entity recognition performance.We conducted experiments on two public CNER datasets in the biomedical domain,namely CMeEE-V2 and Diakg.The results demonstrate the effectiveness of our approach,which achieves F1-score improvements of 7.29 percentage points and 1.64 percentage points compared to the current state-of-the-art(SOTA)models,respectively.

Quickly obtaining densely dispersed coherent particles in steel matrix and its related mechanical property

Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.

Lumbopelvic Fixation and Sacral Decompression for U-shaped Sacral Fractures： Surgical Management and Early Outcome

U-shaped sacral fractures are rare and often difficult to diagnose primarily due to the difficulty in obtaining adequate imaging and the severe associated injuries. These fractures are highly unstable and frequently cause neurological deficits. The majority of surgeons have limited experience in management of U-shaped sacral fractures. No standard treatment protocol for U-shaped sacral fractures has been available till now. This study aimed to examine the management of U-shaped sacral fractures and the early outcomes. Clinical data of 15 consecutive patients with U-shaped sacral fracture who were admitted to our trauma center between 2009 and 2014 were retrospectively analyzed. Demographics, fracture classification, mechanism of injury and operative treatment and deformity angle were assessed. All the patients were treated with lumbopelvic fixation or （and） sacral decompression. EQ-5d score was applied to evaluate the patients＇ quality of life. Of the 15 consecutive patients with U-shaped sacral fracture, the mean age was 28.8 years （range： 15-55 years） at the time of injury. There were 6 females and 9 males. The mean follow- up time was 22.7 months （range： 9-47 months） and mean full weight-bearing time was 9.9 weeks （range： 8-14 weeks）. Ten patients received lumbopelvic fixation and sacral decompression, one lombosacral fixation, and 4 merely sacral decompression due to delayed diagnosis or surgery. The post-operation deformity angle （mean 27.87°, and range： 8°-90°） of the sacrum was smaller than that pre-operation （mean 35.67; range： 15-90） with no significance difference noted. At the latest follow-up, all patients obtained neurological recovery with different extents. Visual analogue score （VAS） was reduced from preoperative 7.07 （range： 5-9） to postoperetive 1.93 （range： 1-3）. All patients could walk without any aid after treatment. Eight patients were able to care for themselves and undertook some daily activities. Five patients had returned to work full time. In conclusion, lumbopelvic fixation is an effective method for stabilization of U-shaped sacral fractures with fewer complications developed. Effective reduction and firm fixation are the prerequisite of early mobilization and neurological recovery. Sacral decompression effectively promotes neurological recovery even in patients with old U-shaped sacral fractures.

GENERAL SOLUTION FOR U-SHAPED BELLOWS OVERALL-BENDING PROBLEMS

The formulae for stresses and angular displacements of U-shaped bellows overall bending in a meridian plane under pure bending moments are presented based on the general solution for slender ring shells proposed by Zhu Weiping, et al. and the solution for ring plates. The results evaluated in this paper are compared with those on EJMA (standards of the expansion joint manufacturers association) and of the experiment given by Li Tingxilz, et al.

Numerical calculation on solar temperature field of a cable-stayed bridge with U-shaped section on high-speed railway

Based on transient temperature field theory of heat conduction, the solar temperature field calculation model of U-shape sectioned high-speed railway cable-stayed bridge under actions of concrete beams and ballast was established. Using parametric programming language, finite element calculation modules considering climate conditions, bridge site, structure dimension and material thermophysical properties were compiled. Six standard day cycles with the strongest yearly radiation among the bridge sites were selected for sectional solar temperature field calculation and temperature distributions under different temperature-sensitive parameters were compared. The results show that under the influence of sunshine, U-shape section of the beam shows obvious nonlinear distribution characteristics and the maximum cross-section temperature difference is more than 21℃; the ballast significantly reduces sunshine temperature difference of the beam and temperature peak of the bottom margin lags with the increase of ballast thickness; the maximum cross-section vertical temperature gradient appears in summer while large transverse temperature difference appears in winter.

Electrokinetic flow in the U-shaped micro-nanochannels

U-shaped micro-nanochannels can generate significant flow disturbance as well as locally amplified electric field, which gives itself potential to be microfluidic mixers, electrokinetic pumps,and even cell lysis process. Numerical simulation is utilized in this work to study the hidden characteristics of the U-shaped micro-nanochannel system, and the effects of key controlling parameters(the external voltage and pressure) on the device output metrics(current, maximum values of electric field, shear stress and flow velocity) were evaluated. A large portion of current flowing through the whole system goes through the nanochannels, rather than the middle part of the microchannel, with its value increasing linearly with the increase of voltage. Due to the local ion depletion near micro-nanofluidic junction, significantly enhanced electric field(as much as 15 fold at V=1 V and P_0=0) as well as strong shear stress(leading to electrokinetic flow) is generated.With increasing external pressure, both electric field and shear stress can be increased initially(due to shortening of depletion region length), but are suppressed eventually at higher pressure due to the destruction of ion depletion layer. Insights gained from this study could be useful for designing nonlinear electrokinetic pumps and other systems.

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

To get a full understanding of hot extrusion,solid solution treatment and aging process on the Al−0.56Mg−0.63Si alloy,the microstructure and mechanical properties of a U-shaped profile were studied through optical microscopy,scanning electrical microscopy,transmission electrical microscopy,hardness,and tensile tests.The coarse equiaxed grains existed near the profile edge as a result of the dynamic recrystallization nucleation and exceeding growth during hot extrusion.The fibrous deformed and sub-structured grains located between the two coarse grain layers,due to the occurrence of work-hardening and dynamic recovery.Perpendicular needle β′′precipitates were distributed inside the grain,and obvious precipitates-free zone appeared after aging treatment.The tensile strength,yield strength and elongation of the aged Al−Mg−Si alloy U-shaped profile were no less than 279.4 MPa,258.6 MPa,and 21.6%,respectively.The fracture morphology showed dimple rupture characteristics.The precipitates and grain boundaries played key role in the strengthening contribution.

PROBLEMS OF U-SHAPED BELLOWS WITH NONLINEAR DEFORM TION OF LARGE AXISYMMETRICAL DEFLECTION(Ⅰ)--COUNTING NONLINEAR DEFORMATIONS OF RING SHELLS AND COMPRESSED ANGLE OF BELLOWS

This paper follows the work of[1,2].There are some progress in dealing with moderately small rotations(the squares of rotation angles are the order of magnitude of strains)of middle surface normals of inside and outside ring shells and compressed angle of bellows.Calculation results agree with experiments well.To bellow design,the method given in this paper is of practical value and the discussion of the influence of compressed angle on characteristic relation is helpful.

ON PROBLEMS OF U-SHAPED BELLOWS WITH NONLINEAR DEFORMATION OF LARGE AXISYMMETRICAL DEFLECTION(Ⅱ)——COUNTING VARIATION OF THICKNESS DISTRIBUTION

On the basis of paper[1],assuming the logarithm of thickness at arbitrary point on a U-shaped bellows meridian is linear with the logarithm of distance between that point and axis of symmetry,perturbation solutions of the corresponding problems of large axisymmetrical deflection are given.The effects of thickness distribution variation,which result from technology factors,on stiffness of bellows are discussed.

MAAUNet:Exploration of U-shaped encoding and decoding structure for semantic segmentation of medical image

In view of the problems of multi-scale changes of segmentation targets,noise interference,rough segmentation results and slow training process faced by medical image semantic segmentation,a multi-scale residual aggregation U-shaped attention network structure of MAAUNet(MultiRes aggregation attention UNet)is proposed based on MultiResUNet.Firstly,aggregate connection is introduced from the original feature aggregation at the same level.Skip connection is redesigned to aggregate features of different semantic scales at the decoder subnet,and the problem of semantic gaps is further solved that may exist between skip connections.Secondly,after the multi-scale convolution module,a convolution block attention module is added to focus and integrate features in the two attention directions of channel and space to adaptively optimize the intermediate feature map.Finally,the original convolution block is improved.The convolution channels are expanded with a series convolution structure to complement each other and extract richer spatial features.Residual connections are retained and the convolution block is turned into a multi-channel convolution block.The model is made to extract multi-scale spatial features.The experimental results show that MAAUNet has strong competitiveness in challenging datasets,and shows good segmentation performance and stability in dealing with multi-scale input and noise interference.

Development and prospects of molten steel deoxidation in steelmaking process

In the long traditional process of steelmaking,excess oxygen is blown into the converter,and alloying elements are used for deoxidation.This inevitably results in excessive deoxidation of products remaining within the steel liquid,affecting the cleanliness of the steel.With the increasing requirements for steel performance,reducing the oxygen content in the steel liquid and ensuring its high cleanliness is necessary.After more than a hundred years of development,the total oxygen content in steel has been reduced from approximately 100×10^(-6)to approximately 10×10^(-6),and it can be controlled below 5×10^(-6)in some steel grades.A relatively stable and mature deoxidation technology has been formed,but further reducing the oxygen content in steel is no longer significant for improving steel quality.Our research team developed a deoxidation technology for bearing steel by optimizing the entire conventional process.The technology combines silicon–manganese predeoxidation,ladle furnace diffusion deoxidation,and vacuum final deoxidation.We successfully conducted industrial experiments and produced interstitial-free steel with natural decarbonization predeoxidation.Non-aluminum deoxidation was found to control the oxygen content in bearing steel to between 4×10^(-6) and 8×10^(-6),altering the type of inclusions,eliminating large particle Ds-type inclusions,improving the flowability of the steel liquid,and deriving a higher fatigue life.The natural decarbonization predeoxidation of interstitial-free steel reduced aluminum consumption and production costs and significantly improved the quality of cast billets.

An ultra-low specific on-resistance trench LDMOS with a U-shaped gate and accumulation layer

An ultra-low specific on-resistance （Ron,sp） oxide trench-type silicon-on-insulator （SOI） lateral double-diffusion metal-oxide semiconductor （LDMOS） with an enhanced breakdown voltage （BV） is proposed and investigated by simulation. There are two key features in the proposed device： one is a U-shaped gate around the oxide trench, which extends from source to drain （UG LDMOS）; the other is an N pillar and P pillar located in the trench sidewall. In the on-state, electrons accumulate along the U-shaped gate, providing a continuous low resistance current path from source to drain. The Ron,sp is thus greatly reduced and almost independent of the drift region doping concentration. In the off-state, the N and P pillars not only enhance the electric field （E-field） strength of the trench oxide, but also improve the E-field distribution in the drift region, leading to a significant improvement in the BV. The BV of 662 V and Ron,sp of 12.4 mΩ.cm2 are achieved for the proposed UG LDMOS. The BV is increased by 88.6% and the Ron,sp is reduced by 96.4%, compared with those of the conventional trench LDMOS （CT LDMOS）, realizing the state-of-the-art trade-off between BV and Ron,sp.

Effect of mold and core preheating temperature on corrosion resistance of casting Al-12Si alloy U-shaped cooling channel

Temperature has an important impact on the corrosion resistance of mold with cooling channels prepared by casting method.The effect of preheating temperature of the mold and the carbon fiber core on the roughness and corrosion resistance of U-shaped cooling channels made of Al-12Si alloy was examined in depth.The experimental results suggest that as the preheating temperature increased from 273 K to 573 K,the roughness of the inner wall of the cooling channel reduced from 96.6μm to 77.0μm.When the preheating temperature continued to increase to 723 K,the roughness increased to 85.3μm.The wetting between the Al melt and the carbon fiber will reduce micro bubbles and waves on the channel wall as the preheating temperature rises,thereby reducing the roughness.However,with the further increase of preheating temperature,it will increase the solidification time of the Al melt.At this time,the carbon fiber and Al melt will take more time to react,which increases the roughness of the channel wall to a certain extent.The results of exfoliation corrosion show that the larger roughness will aggravate exfoliation corrosion.The prolongation of high temperature reaction time between the carbon fiber and the Al melt will lead to the segregation of Si,which is easy to cause intergranular corrosion.Therefore,reasonable preheating temperature has an important impact on the roughness and corrosion resistance of U-shaped cooling channels.

pH-dependent Synthesis of Octa-nuclear Uranyl-oxalate Network Mediated by U-shaped Linkers

In this work,we report a novel octa-nuclear uranyl(U8)motif[(UO2)8O4(μ3-OH)2(μ2-OH)2]4+embedded in a uranyl-oxalate coordination polymer(compound 1)based on a U-shaped linker with extra-long xylylene chains for stabilizing the resulting high-nuclear motif through additional cross-linking connectivity.A comparison with dimeric and monomeric uranyl compounds obtained at different pH value from the same hydrothermal system reveals that,solution pH plays a vital role in formation of this octa-nuclear uranyl motif by promoting hydrolysis of uranyl source.Since high similarity of eight uranium centers in this nearly planar U8 motif here,overlapping and broadening of signals in fluorescence,infra-red(IR)and Raman spectra can be found.

Prediction model for corrosion rate of low-alloy steels under atmospheric conditions using machine learning algorithms

This work constructed a machine learning(ML)model to predict the atmospheric corrosion rate of low-alloy steels(LAS).The material properties of LAS,environmental factors,and exposure time were used as the input,while the corrosion rate as the output.6 dif-ferent ML algorithms were used to construct the proposed model.Through optimization and filtering,the eXtreme gradient boosting(XG-Boost)model exhibited good corrosion rate prediction accuracy.The features of material properties were then transformed into atomic and physical features using the proposed property transformation approach,and the dominant descriptors that affected the corrosion rate were filtered using the recursive feature elimination(RFE)as well as XGBoost methods.The established ML models exhibited better predic-tion performance and generalization ability via property transformation descriptors.In addition,the SHapley additive exPlanations(SHAP)method was applied to analyze the relationship between the descriptors and corrosion rate.The results showed that the property transformation model could effectively help with analyzing the corrosion behavior,thereby significantly improving the generalization ability of corrosion rate prediction models.

Effects of iron oxide on crystallization behavior and spatial distribution of spinel in stainless steel slag

Chromium plays a vital role in stainless steel due to its ability to improve the corrosion resistance of the latter.However,the re-lease of chromium from stainless steel slag(SSS)during SSS stockpiling causes detrimental environmental issues.To prevent chromium pollution,the effects of iron oxide on crystallization behavior and spatial distribution of spinel were investigated in this work.The results revealed that FeO was more conducive to the growth of spinels compared with Fe2O3 and Fe3O4.Spinels were found to be mainly distrib-uted at the top and bottom of slag.The amount of spinel phase at the bottom decreased with the increasing FeO content,while that at the top increased.The average particle size of spinel in the slag with 18wt%FeO content was 12.8μm.Meanwhile,no notable structural changes were observed with a further increase in FeO content.In other words,the spatial distribution of spinel changed when the content of iron oxide varied in the range of 8wt%to 18wt%.Finally,less spinel was found at the bottom of slag with a FeO content of 23wt%.

An Integrated Analysis on the Synergistic Reduction of Carbon and Pollution Emissions from China’s Iron and Steel Industry

Decarbonization and decontamination of the iron and steel industry(ISI),which contributes up to 15%to anthropogenic CO_(2) emissions(or carbon emissions)and significant proportions of air and water pollutant emissions in China,are challenged by the huge demand for steel.Carbon and pollutants often share common emission sources,indicating that emission reduction could be achieved synergistically.Here,we explored the inherent potential of measures to adjust feedstock composition and technological structure and to control the size of the ISI to achieve carbon emission reduction(CER)and pollution emission reduction(PER).We investigated five typical pollutants in this study,namely,petroleum hydrocarbon pollutants and chemical oxygen demand in wastewater,particulate matter,SO_(2),and NO_(x) in off gases,and examined synergies between CER and PER by employing cross elasticity for the period between 2022 and 2035.The results suggest that a reduction of 8.7%-11.7%in carbon emissions and 20%-31%in pollution emissions(except for particulate matter emissions)could be achieved by 2025 under a high steel scrap ratio(SSR)scenario.Here,the SSR and electric arc furnace(EAF)ratio serve critical roles in enhancing synergies between CER and PER(which vary with the type of pollutant).However,subject to a limited volume of steel scrap,a focused increase in the EAF ratio with neglection of the available supply of steel scrap to EAF facilities would lead to an increase carbon and pollution emissions.Although CER can be achieved through SSR and EAF ratio optimization,only when the crude steel production growth rate remains below 2.2%can these optimization measures maintain the emissions in 2030 at a similar level to that in 2021.Therefore,the synergistic effects between PER and CER should be considered when formulating a development route for the ISI in the future.

Numerical Simulation of U-Shaped Metal Rings in a Wind-Sand Environment

The interaction of U-shaped rings used for power transmission hardware with a wind-sand field is simulated numerically.A standard k
turbulence model is used in synergy with an Eulerian-Lagrangian approach.The results show that the wind pressure on the windward side of the U-shaped ring is the highest,a negative pressure zone appears on both sides of the U-shaped ring,while a Kármán Vortex Street is created on its leeward side.There are three possible regimes of motion for the sand grains in the wind field.Sand grains with size below 0.125 mm can follow the airflow directly into the contact area of two U-shaped rings.When the sand size is about 0.1 mm,the number of sand grains that are blown into the contact area attains a maximum.Through the simulation of U-shaped rings in the wind-sand field,the dynamics of such processes are explained in detail,thereby providing relevant information for the subsequent protection and design of connecting hardware used for power transmission.