Review on synergistic damage effect of irradiation and corrosion on reactor structural alloys

The synergistic damage effect of irradiation and corrosion of reactor structural materials has been a prominent research focus.This paper provides a comprehensive review of the synergistic effects on the third-and fourth-generation fission nuclear energy structural materials used in pressurized water reactors and molten salt reactors.The competitive mechanisms of multiple influencing factors,such as the irradiation dose,corrosion type,and environmental temperature,are summarized in this paper.Conceptual approaches are proposed to alleviate the synergistic damage caused by irradiation and corrosion,thereby promoting in-depth research in the future and solving this key challenge for the structural materials used in reactors.

Effect of Postharvest UV-C Irradiation on Phenolic Compound Content and Antioxidant Activity of Tomato Fruit During Storage

Mature-green tomato fruit （Solanum lycopersicum cv. Zhenfen 202） were exposed to different UV-C irradiation at 2, 4, 8, and 16 kJ m-2 and then stored under the dark at 14°C and 95% relative humidity （RH） for 35 d. Of these four doses, UV-C irradiation at 4 and 8 kJ m-2 significantly increased total phenolic contents in present tomato fruit by 21.2 and 20.2%, respectively. Furthermore, UV-C irradiation at 4 or 8 kJ m-2 promoted the accumulation of total flavonoids and increased the antioxidant activity. 2 or 16 kJ m-2 UV-C irradiation also enhanced antioxidant activity, but to a lesser extent. Seven phenolic compounds, viz., gallic acid, （＋）-catechin, chlorogenic acid, cafferic acid, syringic acid, p-coumaric acid, and quercetin in tomato fruit were identified and quantified by HPLC. Gallic acid was the major phenolic compound in tomato fruit and significantly correlated with antioxidant activity. 4 or 8 kJ m-2 UV-C irradiation significantly increased the contents of gallic acid, chlorogenic acid, syringic acid, p-coumaric acid, and quercetin. The optimum dose of UV-C irradiation in terms of increased phenolic compound content and enhanced Antioxidant activity was determined to be 4 or 8 kJ m-2.

Effects of UV-B irradiation on isoforms of antioxidant enzymes and their activities in red alga Grateloupia filicina(Rhodophyta)

Macroalgae in a littoral zone are inevitably exposed to UV-B irradiance. We analyzed the effects of UV-B on isoenzyme patterns and activities of superoxide dismutase （SOD）, peroxidase （POX）, catalase （CAT）, and ascorbate peroxidase （APX） of red algae Grateloupia filicina （Lamour.） C. Agardh. The activities of SOD, CAT, and APX changed in response to UV-B in a time- and dose-dependent manner. POX activity increased significantly under all three UV-B treatments. The enzymatic assay showed three distinct bands of SODI （Mn-SOD）, SODII （Fe-SOD）, and SODIII （CuZn-SOD） under a low （Luv） and medium （Muv） dose of UV-B irradiation, while SODI and SODIII activities decreased significantly when exposed to a high dose of UV-B irradiation （Huv）. The activity of POX isoenzymes increased significantly after exposure to UV-B, which is consistent with the total activity. In addition, a clear decrease in activity of CATIV was detected in response to all the three doses of UV treatments. Some bands ofAPX isoenzyme were also clearly influenced by UV-B irradiation. Correspondingly, the daily growth rate declined under all the three exposure doses, and was especially significant under Muv and Huv treatments. These data suggest that, although the protection mechanisms of antioxidant defense system are partly inducible by UV-B to prevent the damage, G.filicina has incomplete tolerance to higher UV-B irradiation stress.

Neutron irradiation influence on high-power thyristor device under fusion environment

Because of their economy and applicability,high-power thyristor devices are widely used in the power supply systems for large fusion devices.When high-dose neutrons produced by deuterium–tritium(D–T)fusion reactions are irradiated on a thyristor device for a long time,the electrical characteristics of the device change,which may eventually cause irreversible damage.In this study,with the thyristor switch of the commutation circuit in the quench protection system(QPS)of a fusion device as the study object,the relationship between the internal physical structure and external electrical parameters of the irradiated thyristor is established.Subsequently,a series of targeted thyristor physical simulations and neutron irradiation experiments are conducted to verify the accuracy of the theoretical analysis.In addition,the effect of irradiated thyristor electrical characteristic changes on the entire QPS is studied by accurate simulation,providing valuable guidelines for the maintenance and renovation of the QPS.

Demonstration of irradiation-resistant 4H-SiC based photoelectrochemical water splitting

4H silicon carbide(4H-SiC)has gained a great success in high-power electronics,owing to its advantages of wide bandgap,high breakdown electric field strength,high carrier mobility,and high thermal conductivity.Considering the high carrier mobility and high stability of 4H-SiC,4H-SiC has great potential in the field of photoelectrochemical(PEC)water splitting.In this work,we demonstrate the irradiation-resistant PEC water splitting based on nanoporous 4H-SiC arrays.A new two-step anodizing approach is adopted to prepare 4H-SiC nanoporous arrays with different porosity,that is,a constant low-voltage etching followed by a pulsed high-voltage etching.The constant-voltage etching and pulsed-voltage etching are adopted to control the diameter of the nanopores and the depth of the nanoporous arrays,respectively.It is found that the nanoporous arrays with medium porosity has the highest PEC current,because of the enhanced light absorption and the optimized transportation of charge carriers along the walls of the nanoporous arrays.The performance of the PEC water splitting of the nanoporous arrays is stable after the electron irradiation with the dose of 800 and 1600 k Gy,which indicates that 4H-SiC nanoporous arrays has great potential in the PEC water splitting under harsh environments.

In situ TEM investigation of electron irradiation and aging-induced high-density nanoprecipitates in an Mg-10Gd-3Y-1Zn-0.5Zr alloy

In-situ electron irradiation and aging are applied to introduce high-density precipitates in an Mg-10Gd-3Y-1Zn-0.5Zr(GWZ1031K,wt.%)alloy to improve the hardness.The results show that the hardness of the Mg alloy after irradiation for 10 h and aging for 9 h at 250℃ is 1.64 GPa,which is approximately 64% higher than that of the samples before being treated.It is mainly attributed to γ'precipitates on the basal plane after irradiation and the high-density nanoscale β'precipitates on the prismatic plane after aging,which should be closely related to the irradiation-induced homogenous clusters.The latter plays a key role in precipitation hardening.This result paves a way to improve the mechanical properties of metallic materials by tailoring the precipitation through irradiation and aging.

Microwave irradiation-induced alterations in physicochemical properties and methane adsorption capability of coals:An experimental study using carbon molecular sieve

In order to comprehend the applicability of microwave irradiation for recovering coalbed methane,it is necessary to evaluate the microwave irradiation-induced alterations in coals with varying levels of metamorphism.In this work,the carbon molecular sieve combined with KMnO_(4)oxidation was selected to fabricate carbon molecular sieve with diverse oxidation degrees,which can serve as model substances toward coals.Afterwards,the microwave irradiation dependences of pores,functional groups,and highpressure methane adsorption characteristics of model substances were studied.The results indicated that microwave irradiation causes rearrangement of oxygen-containing functional groups,which could block the micropores with a size of 0.40-0.60 nm in carbon molecular sieve;meanwhile,naphthalene and phenanthrene generated by macro-molecular structure pyrolysis due to microwave irradiation could block the micropores with a size of 0.70-0.90 nm.These alterations in micropore structure weaken the saturated methane adsorption capacity of oxidized carbon molecular sieve by 2.91%-23.28%,suggesting that microwave irradiation could promote methane desorption.Moreover,the increased mesopores found for oxidized carbon molecular sieve after microwave irradiation could benefit CH4 diffusion.In summary,the oxidized carbon molecular sieve can act as model substances toward coals with different ranks.Additionally,microwave irradiation is a promising technology to enhance coalbed methane recovery.

Two-dimensional particle-in-cell modeling of blow-off impulse by X-ray irradiation

Space objects such as spacecraft or missiles may be exposed to intense X-rays in outer space,leading to severe damage.The reinforcement of these objects to reduce the damage caused by X-ray irradiation is a significant concern.The blow-off impulse(BOI)is a crucial physical quantity for investigating material damage induced by X-ray irradiation.However,the accurate calculation of BOI is challenging,particularly for large deformations of materials with complex configurations.In this study,we develop a novel two-dimensional particle-in-cell code,Xablation2D,to calculate BOIs under far-field X-ray irradiation.This significantly reduces the dependence of the numerical simulation on the grid shape.The reliability of this code is verified by simulation results from open-source codes,and the calculated BOIs are consistent with the experimental and analytical results.

Effect of high-energy Ne ions irradiation on mechanical properties difference between Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5)metallic glass and crystalline W

In this paper,high-energy Ne ions were used to irradiate Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) metallic glass(MG)and crystalline W to investigate their difference in mechanical response after irradiation.The results showed that with the irradiation dose increased,the tensile micro-strain increased,nano-hardness increased from 7.11 GPa to 7.90 GPa and 8.62 GPa,Young’s modulus increased,and H3/E2 increased which indicating that the plastic deformability decreased in crystalline W.Under the same irradiation conditions,the Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG still maintained the amorphous structure and became more disordered despite the longer range and stronger displacement damage of Ne ions in Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG than in crystalline W.Unlike the irradiation hardening and embrittlement behavior of crystalline W,Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG showed the gradual decrease in hardness from 6.02 GPa to 5.89 GPa and 5.50 GPa,the decrease in modulus and the increase in plastic deformability with the increasing dose.Possibly,the irradiation softening and toughening phenomenon of Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG could provide new ideas for the design of nuclear materials.

Effect of three-volt moxibustion with helium-neon laser irradiation on quality of care in patients with lumbar radiculopathy spondylosis

BACKGROUND Lumbar radiculopathy spondylosis is a relatively common orthopedic disease with a high incidence rate.It most commonly occurs in the lumbar 4-5 and lumbar 5-sacral 1 vertebrae,which account for approximately 95%of cases.It mostly occurs in people aged 30-50 years old and greatly affects their quality of life.AIM To determine the effect of triple-voltage acupuncture combined with helium-neon laser irradiation on the quality of care and improvement of symptoms in patients with lumbar radiculopathy spondylolisthesis.METHODS In this study,we selected 120 patients with lumbar radiculopathy spondylosis who were treated at our hospital between June 2019 to June 2020.The patients were divided into control and observation groups according to the random number table method,with 60 patients in each group.Patients in the observation group were treated with three-volt moxibustion combined with helium-neon laser irradiation,and those in the control group were treated with lumbar traction.After 1 month of treatment,the lumbar pain scores,lumbar spine motor functions,clinical treatment effects,and nursing satisfaction of the two groups were compared.RESULTS The results showed that acupuncture combined with laser irradiation significantly improved the patients'clinical symptoms,i.e.,reduced their low back pain,significantly lower numerical rating scale pain scores in the observation group than in the control group,and better lumbar spine motility than in the control group,compared to lumbar traction.In addition,they were cared for.The treatment effectiveness rate of the observation group was 95.5%,which was significantly higher than that of the control group(81.67%).Satisfaction with care was higher than 90 points in both groups,but the difference was not statistically significant.CONCLUSION Our study provides a clinical rationale for the future treatment of patients with lumbar spine disease.However,further extensive research is needed for validation.

Development of a new irradiation-embrittlement prediction model for reactor pressure-vessel steels

Predicting the transition-temperature shift(TTS)induced by neutron irradiation in reactor pressure-vessel(RPV)steels is important for the evaluation and extension of nuclear power-plant lifetimes.Current prediction models may fail to properly describe the embrittlement trend curves of Chinese domestic RPV steels with relatively low Cu content.Based on the screened surveillance data of Chinese domestic and similar international RPV steels,we have developed a new fluencedependent model for predicting the irradiation-embrittlement trend.The fast neutron fluence(E>1 MeV)exhibited the highest correlation coefficient with the measured TTS data;thus,it is a crucial parameter in the prediction model.The chemical composition has little relevance to the TTS residual calculated by the fluence-dependent model.The results show that the newly developed model with a simple power-law functional form of the neutron fluence is suitable for predicting the irradiation-embrittlement trend of Chinese domestic RPVs,regardless of the effect of the chemical composition.

The impact of^(60)Co-γirradiation on the chemical constituents of Chuanxiong Rhizoma

Background:In order to clarify the inmpat ofγirradiation on the chemical composition of traditional Chinese medicine,this paper carefully choosed Chuanxiong Rhizoma to carry on a demonstration study.Methods:Through a meticulous assessment,a comprehensive comparison was made between the irradiated and unirradiated Chuanxiong Rhizoma samples.The property characteristics were investigated by colorimeter and electronic nose.The changes in chemical structures and contents was analyzed by fourier infrared spectroscopy,high performance liquid chromatography and fingerprinting.In a quest to uncover the presence of any new radiolysis products,cutting-edge techniques like ultra performance liquid chromatography-quadrupole-time of flight-mass spectrometry and gas chromatography-mass spectrometry were employed.Moreover,the difference of antioxidant activity were investigated.Results:The irradiation doses within 12 kGy had no significant effects on the content of the main chemical components,characteristics and in vitro antioxidant activity of Chuanxiong Rhizoma,while changes in some functional groups and degradation of some volatile oil components containing olefins need further study.Conclusion:This study indicates that^(60)Co-γirradiation is a stable method for sterilization of Chuanxiong Rhizoma.It’s also provide a reference for the establishment of irradiation standards for Chuanxiong Rhizoma and other aromatic medicinal plants.

Effect of UV-B irradiation on interspecific competition between Ulva pertusa and Grateloupia filicina

We report the effect of UVoB irradiation （9.6 kJ m-2 day^-） on interspecific competition between two species of macroalgae, Ulva pertusa （U） and Grateloupiafilicina （G）, in co-culture. Growth of U. pertusa and G. filicina was inhibited by UV-B irradiation in mono-culture and specific growth rate （μ） declined as a result. Interspecific competition between U. pertusa and G filicina was closely related to the initial weights when co-cultured. When initial ratios of U. pertusa （U） to G filicina （G） were U：G=I.2：I and 1：1, U. pertusa was the dominant algae. When the initial U：G ratio was 1：1.2, G. filicina was competitively dominant in the earlier stage, but U. pertusa grew faster, superseding G. filicina in the later stage. At initial ration U：G = 1：1.4, G. filicina was predominant. Under UV-B irradiation, the competitive ability of G filicina was weakened and the interspecific competitive balance favored U. pertusa, which suggests that G. filicina was more sensitive to UV-B irradiation. We also probed the potential allelopathic effects between the two species, which led to mutual growth inhibition.

Observation of therapeutic effect of lamp irradiation combined with purple gromwell oil gauze on alleviating intestinal colic in patients

BACKGROUND Intestinal colic is a common complication in patients who have undergone radical surgery for colorectal cancer.Traditional Chinese medicine has advantages,including safety and stability,for the treatment of intestinal colic.Lamp irra-diation for abdominal ironing has been applied in the treatment of many gas-trointestinal diseases.Purple gromwell oil has the effects of clearing heat,cooling blood,reducing swelling,and relieving pain.RESULTS The general effective rate in the observation group was 95.00%,which was significantly higher than that in the control group(86.67%,P<0.05).Before treatment,there was no significant difference in the duration of symptoms between the groups(P>0.05).After 1,2,3,and 4 d of treatment,the duration of symptoms in both groups were decreased,and the duration in the observation group was significantly lower than that in the control group(96.54±9.57 vs 110.45±11.23,87.26±12.07 vs 104.44±11.68,80.45±16.21 vs 99.44±14.95,73.18±15.58 vs 92.17±14.20;P<0.05).After 1,3,5,and 7 d of treatment,the NRS scores in both groups were decreased,and the NRS scores in the observation group were significantly lower than those in the control group(3.56±0.41 vs 4.04±0.58,3.07±0.67 vs 3.74±1.02,2.52±0.76 vs 3.43±0.85,2.03±0.58 vs 3.03±0.82;P<0.05).There was no significant difference in the rate of adverse reaction occurrence between the groups(P>0.05).CONCLUSION The use of lamp irradiation combined with purple gromwell oil gauze in patients with intestinal colic after radical surgery for colorectal cancer can reduce symptom duration,alleviate intestinal colic,and improve treatment efficacy,and this approach is safe.It is worth promoting the use of this treatment in clinical practice.

Protective and Regenerative Efficacy of a Plant Oil-Based Day and Night Cream: Investigated by a Novel Approach to Reveal the Impact of Blue Light Irradiation on Epidermal Barrier Integrity and Lipid Matrix

In recent years, the harmful effects of blue light (400 - 500 nm) as a component of visible light (400 - 700 nm) have increasingly gained attention of science, industry, and consumers. To date, only a few in vivo test methods for measuring the effects of blue light on the skin have been described. A direct measurement method that can detect the immediate effects of blue light on the epidermal permeability barrier (EPB) is still lacking. In this study, we present a new methodological approach that can be used to investigate both the protective and regenerative effects of cosmetic products on the EPB after blue light irradiation. In a study with 14 female volunteers, it was investigated whether the regular application of an O/W emulsion (day cream) can strengthen and protect the epidermal barrier against damaging blue light radiation of 60 J/cm2 (protective study design) and also whether a disruption of the epidermal barrier caused by blue light radiation is restored faster and better by the regular application of another O/W emulsion (night cream) than in product-untreated skin (regenerative study design). The two O/W emulsions are different in plant oil, active ingredient composition and texture. The seven-day treatment with the day cream initially led to a significant increase in the normalized lipid lamellae length in the intercellular space, whereas the irradiation with blue light after 24 hours led to a significant decrease in the lipid lamellae length in the untreated test area, but not in the area previously treated with the product. Regarding the regenerative study design, a two-day treatment with the night cream was able to restore a blue-light-induced decrease in lipid lamellae length in the intercellular space. In summary, with the study designs presented here, the protective and regenerative effect of two cosmetic products could be demonstrated for the first time on the integrity of the EPB after blue light irradiation and the data showed that the Lipbarvis® method is suitable for investigating the damaging effects of blue light on the EPB in vivo.

An electron beam irradiation-assisted coating method for the regulation of hydrophilicity and hydrophobicity

Developing a stable,reliable,and industrially compatible method to control hydrophobicity is crucial for separation,transportation,and the generation of special surfaces.An e-HMS-PDMS silica gel nanoparticle coating was prepared using a two-step electron beam irradiation(EBI)process,consisting of(i)grafting of two organic groups onto thiol-functionalized hollow mesoporous silica(HMS-SH)with 10 MeV EBI and(ii)curing of polydimethylsiloxane(PDMS)onto silicone rubber using the HMS hybrid materials prepared in step i as an additive with 200 keV EBI.The tuneable grafting of functional groups and the surface properties of the silica,which was embedded in the PDMS layer,allowed us to precisely control the hydrophilicity of the PDMS layer by means of altering the grafting gradient of the silica and the loading ratio of the monomers.A diverse range of vinyl-structured monomers can be used in this method,and the selection of suitable monomers is vital in determining the physical properties of the coating layer.The hydrophilicity of the coating can be linearly controlled within a specific range(50°to 155°)by using suitable monomers,allowing for the design of surfaces with specific hydrophilic and hydrophobic requirements.

Chemical Dosimetry during Alpha Irradiation: A Specific System for UV-Vis <i>in Situ</i>Measurement

This paper is devoted to the study of the potentiality of the Fricke dosimeter for the characterization of the highly energetic (62.1 MeV) α particles beams generated by a new cyclotron facility, namely ARRONAX started in 2009. Such for this high energetic α beam, in situ dosimetry is performed in order to avoid radiation safety inconvenience and to earn run time of irradiation. Therefore, an in situ Fricke dosimetry protocol is developed and its reliability is checked by comparison with other experiments carried out by using the traditional method (ex situ Fricke dosimetry) within another cyclotron facility (CEMHTI) and by comparison with literature data. To author’s knowledge, it is the first time that Fricke dosimetry is performed during the α irradiation experiment. The results of these in situ dosimetry experiments show that the value of ferric ions radiolytic yield (G(Fe3+) = (11.7 ± 1.2) 10–7 mol?J–1) extrapolated from literature data can be used for this higher energy of α particles (Eα = 62.1 MeV).

Study the Influence of UV-Irradiation on the Photo Stability of Pure and Plasticized Poly (4-Vinyl Biphenyl) in Solid Films

The effect of UV irradiation and blending with phthalate and terephthalate plasticizers on the photo-stability of Poly (4-vinyl biphenyl) was studied at different intervals of irradiation time and in presence of air. The increase in irradiation time on the photodegradation of polymer thin films caused a change in the intensity and shape of the fluorescence band. It has been found that the stability of the polymer decreases with the increase of irradiation time, and to increases with the increase of the amount of added phthalate and terephthalate plasticizers, which is evidence of polymer photodegradation. The FT-IR spectra of irradiated pure and blended polymer with phthalate and terephthalate plasticizers showed a decrease in some absorption bands and increase in the other bands, this is also another factor for the occurrence of photo degradation of the irradiated polymer. The increase in the intensity of absorption of carbonyl and hydroxyl region, indicates a possible photogegradation of polymeric chains and the formation of alcohols, aliphatic ketones and to the increase in the number of (C=C) that resulted from hydrogen abstraction during chains-scission.

Comparative Study of Synergistic Effects of Antibiotics with Triangular Shaped Silver Nanoparticles, Synthesized Using UV-Light Irradiation, on <i>Staphylococcus aureus</i>and <i>Pseudomonas aeruginosa</i>

In the present work, a comparative study of antibacterial activity and synergistic effects of triangular silver nanoparticles in combination with two standard antibiotics is discussed for Staphylococcus aureus and Pseudomonas aeruginosa. A green route was developed to synthesise silver nanoparticles in which silver oxalate was taken as precursor, black tea leaves extract as surfactant and chitin as a stabilizing agent. A grey coloured colloidal solution of silver nanoparticles was obtained which was characterized by using various techniques like X-ray diffractometer (XRD), transmission electron microscopy (TEM) and UV-visible spectroscopy. Anti-bacterial studies gave approximately equal inhibition zones for both the combinations which states that silver nanoparticles are to be equally effective and synergistic effects were clearly observed in case of P. aeruginosa.

Red-mud treatment using oxalic acid by UV irradiation assistance

Red-mud is the residue from the Bayer process, in which the iron minerals should be removed before red-mud is used to produce refractory materials. The iron minerals in red-mud were extracted by oxalic acid solution. The content of Fe （calculated in Fe203） in red-mud was reduced from 17.6% to less than 1% after being treated by 1 mol/L oxalic acid solution at 75 ℃ for 2 h. The Fe（Ⅲ） oxalate solution obtained was then irradiated by UV light, resulting in the precipitation of Fe（Ⅱ） oxalate. Under UV photocatalysis, more than 90% of Fe（Ⅲ） oxalate in the extracted solution was transformed into the precipitation of Fe（Ⅱ） oxalate crystallite （fl-FeC2O4·2H2O）. The filtrate from the Fe（Ⅱ） oxalate precipitate filtration could be reused in the next cycle. The mechanism ofUV photocatalysis precipitation was also discussed.