UV-LED耐黄变木器辊涂面漆的制备及性能研究

本研究围绕UV-LED固化光源的应用,探究了一种耐黄变涂料的制备工艺,以优化UV涂料的耐黄性为重点,探讨多官能团单体、光引发剂、二苯甲酮等助剂对涂料性能的影响。对比不同组分对涂层的附着力、硬度和耐黄变性能的影响。结果表明,适量的多官能团单体对涂层的硬度、附着力有增强作用,但过量则会产生负作用;氧磷类光引发剂有利于提高抗黄性;使用二苯甲酮需要在抗黄性和成本之间平衡。添加紫外光吸收剂、阻胺光稳定剂,可使涂层耐黄变性保持长期稳定。

蓖麻油基光敏树脂的合成及其UV-LED固化无影胶的性能

以蓖麻油、异佛尔酮二异氰酸酯、丙烯酸羟乙酯为原料,通过无溶剂法合成的一种蓖麻油基聚氨酯丙烯酸酯(CO-PUA)作为光敏单体。将自制的CO-PUA、活性稀释剂、硅烷偶联剂、附着力促进剂、光引发剂以及四(3-巯基丙酸)季戊四醇酯(PETMP)按比例混合制得一系列UV-LED固化无影胶,并考察了PETMP的添加量对无影胶性能的影响。结果表明:引入PETMP的UV-LED固化无影胶具有巯基-烯“点击化学”的反应特性,消除了氧阻的危害,无影胶固化完全。当PETMP的添加量为0.5 g时,具有最佳黏结性能,以有机玻璃-有机玻璃、有机玻璃-不锈钢、玻璃-不锈钢为搭接基材测得黏结拉伸剪切强度分别为2.44 MPa、5.06 MPa和5.70 MPa。

Determination of Timer Error and Evaluation of Its Effect on Dose for OB6, GammaBeam X200 and X-Ray Irradiators at the Secondary Standard Dosimetry Laboratory in Nigeria

Timer error as well as its convention is very important for dose accuracy during irradiation. This paper determines the timer error of irradiators at Secondary Standard Dosimetry Laboratory (SSDL) in Nigeria. The irradiators are Cs-137 OB6 irradiator and X-ray irradiators at the Protection level SSDL;and Co-60 irradiator at the Therapy Level SSDL. PTW UNIDOS electrometer and LS01 Ionization chamber were used at the Protection Level to obtain doses for both Cs-137 OB6 and X-ray irradiators while an IBA farmer type ionization chamber and an IBA DOSE 1 electrometer were used at the Protection Level SSDL. Single/multiple exposure method and graphical method were used in the determination of the timer error for the three irradiators. The timer error obtained for Cs-137 OB6 irradiator was 0.48 ± 0.01 s, the timer error for the X-ray irradiator was 0.09 ± 0.01 s while the timer error obtained for GammaBeam X200 was 1.21 ± 0.04 s. It was observed that the timer error is not affected by source to detector distance. It was also observed that the timer error of Co-60 Gamma X200 irradiator is increasing with the age of the machine. Source to detector distance and field size do not contribute towards the timer error of the irradiators. The timer error of the Co-60 Gamma X200 irradiator (the only irradiator among the irradiators with a pneumatic system) increases with the age of the irradiator.

紫外发光二极管(UV-LED)技术对食品微生物灭活应用的研究进展

紫外辐照是一种非热杀菌技术,汞蒸气紫外灯是现阶段用于食品卫生处理的主要设备,但受某些因素影响,汞灯的生产使用将逐渐变少,被环保节能的紫外发光二极管(UV-LED)取代是一种不可避免的趋势。本文根据UV-LED发光原理和多波长耦合应用的特点,综述了对微生物灭活的机理、探究了影响灭活效果的因素(波长、紫外剂量和物料特性)、处理食品的灭菌效果以及对部分食品品质的影响,为UV-LED在食品领域的杀菌处理工艺和设备参数优化提供参考。

大功率UV-LED散热与纳米TiO_(2)光催化酸性红26耦合系统性能

设计了大功率UV-LED散热和纳米TiO_(2)光催化酸性红26耦合系统,采用污水循环冷却UV-LED提高灯珠工作效率的同时实现污水光催化降解脱色,将污水循环系统与紫外光源冷却耦合是创新点。采用模拟优化UV-LED灯珠排布,以污水脱色为探针反应,发现污水冷却能使UV-LED结温降低41.2%,平均辐照度和污水脱色效率分别提高11.03%和1.68倍。环境因素对污水降解性能影响结果表明,光催化活性与污染物浓度成反比,与催化剂初始浓度成正比,达0.75g/L后趋于稳定;考虑吸附和氧化基团对降解速率影响,最优pH为2。本设计与传统环隙式反应器对比,表观量子产率和脱色效率分别是后者的2.3倍和4.3倍,能耗仅为后者的9.1%。该耦合系统在UV-LED的温度控制和废水处理领域具有潜在应用价值。

超声波联合UV-LED对耐四环素大肠杆菌的灭活效能

采用超声波-UV-LED联合工艺以期实现对污水中抗生素耐药菌(ARB)的去除,通过逐一分析不同频率超声波(33,120,200kHz)、不同波长UV-LED(255,275nm)对耐四环素大肠杆菌的灭活以及膜损伤效能,从而确定超声波联合UV的工艺参数.结果表明,单独超声波作用时,33kHz超声波效果最佳,在输入功率为50W、输入剂量为1080kJ/L时,大肠杆菌的灭活率为2.30log,细胞膜损伤百分比为61.09%;单独UV-LED作用下,辐照剂量为19.92mJ/cm^(2)的255nm UV-LED对细菌的灭活率为5.32log,细胞膜的损伤百分比为2.52%;275nm UV-LED对细菌的灭活率为4.63log,膜损伤百分比为34.95%;但是二者联合使用未产生协同效应.超声波联合UV-LED可使消毒效能显著提升至7.45log,细胞膜损伤提高至68.74%,且能够有效抑制大肠杆菌的复活,复活率降低至0.4%,超声波联合UV-LED在细菌耐药性控制方面显现出巨大的潜力.

Neutron irradiation influence on high-power thyristor device under fusion environment

Because of their economy and applicability,high-power thyristor devices are widely used in the power supply systems for large fusion devices.When high-dose neutrons produced by deuterium–tritium(D–T)fusion reactions are irradiated on a thyristor device for a long time,the electrical characteristics of the device change,which may eventually cause irreversible damage.In this study,with the thyristor switch of the commutation circuit in the quench protection system(QPS)of a fusion device as the study object,the relationship between the internal physical structure and external electrical parameters of the irradiated thyristor is established.Subsequently,a series of targeted thyristor physical simulations and neutron irradiation experiments are conducted to verify the accuracy of the theoretical analysis.In addition,the effect of irradiated thyristor electrical characteristic changes on the entire QPS is studied by accurate simulation,providing valuable guidelines for the maintenance and renovation of the QPS.

In situ TEM investigation of electron irradiation and aging-induced high-density nanoprecipitates in an Mg-10Gd-3Y-1Zn-0.5Zr alloy

In-situ electron irradiation and aging are applied to introduce high-density precipitates in an Mg-10Gd-3Y-1Zn-0.5Zr(GWZ1031K,wt.%)alloy to improve the hardness.The results show that the hardness of the Mg alloy after irradiation for 10 h and aging for 9 h at 250℃ is 1.64 GPa,which is approximately 64% higher than that of the samples before being treated.It is mainly attributed to γ'precipitates on the basal plane after irradiation and the high-density nanoscale β'precipitates on the prismatic plane after aging,which should be closely related to the irradiation-induced homogenous clusters.The latter plays a key role in precipitation hardening.This result paves a way to improve the mechanical properties of metallic materials by tailoring the precipitation through irradiation and aging.

Microwave irradiation-induced alterations in physicochemical properties and methane adsorption capability of coals:An experimental study using carbon molecular sieve

In order to comprehend the applicability of microwave irradiation for recovering coalbed methane,it is necessary to evaluate the microwave irradiation-induced alterations in coals with varying levels of metamorphism.In this work,the carbon molecular sieve combined with KMnO_(4)oxidation was selected to fabricate carbon molecular sieve with diverse oxidation degrees,which can serve as model substances toward coals.Afterwards,the microwave irradiation dependences of pores,functional groups,and highpressure methane adsorption characteristics of model substances were studied.The results indicated that microwave irradiation causes rearrangement of oxygen-containing functional groups,which could block the micropores with a size of 0.40-0.60 nm in carbon molecular sieve;meanwhile,naphthalene and phenanthrene generated by macro-molecular structure pyrolysis due to microwave irradiation could block the micropores with a size of 0.70-0.90 nm.These alterations in micropore structure weaken the saturated methane adsorption capacity of oxidized carbon molecular sieve by 2.91%-23.28%,suggesting that microwave irradiation could promote methane desorption.Moreover,the increased mesopores found for oxidized carbon molecular sieve after microwave irradiation could benefit CH4 diffusion.In summary,the oxidized carbon molecular sieve can act as model substances toward coals with different ranks.Additionally,microwave irradiation is a promising technology to enhance coalbed methane recovery.

Two-dimensional particle-in-cell modeling of blow-off impulse by X-ray irradiation

Space objects such as spacecraft or missiles may be exposed to intense X-rays in outer space,leading to severe damage.The reinforcement of these objects to reduce the damage caused by X-ray irradiation is a significant concern.The blow-off impulse(BOI)is a crucial physical quantity for investigating material damage induced by X-ray irradiation.However,the accurate calculation of BOI is challenging,particularly for large deformations of materials with complex configurations.In this study,we develop a novel two-dimensional particle-in-cell code,Xablation2D,to calculate BOIs under far-field X-ray irradiation.This significantly reduces the dependence of the numerical simulation on the grid shape.The reliability of this code is verified by simulation results from open-source codes,and the calculated BOIs are consistent with the experimental and analytical results.

Ultraviolet‑Irradiated All‑Organic Nanocomposites with Polymer Dots for High‑Temperature Capacitive Energy Storage

Polymer dielectrics capable of operating efficiently at high electric fields and elevated temperatures are urgently demanded by next-generation electronics and electrical power systems.While inorganic fillers have been extensively utilized to improved high-temperature capacitive performance of dielectric polymers,the presence of thermodynamically incompatible organic and inorganic components may lead to concern about the long-term stability and also complicate film processing.Herein,zero-dimensional polymer dots with high electron affinity are introduced into photoactive allyl-containing poly(aryl ether sulfone)to form the all-organic polymer composites for hightemperature capacitive energy storage.Upon ultraviolet irradiation,the crosslinked polymer composites with polymer dots are efficient in suppressing electrical conduction at high electric fields and elevated temperatures,which significantly reduces the high-field energy loss of the composites at 200℃.Accordingly,the ultraviolet-irradiated composite film exhibits a discharged energy density of 4.2 J cm^(−3)at 200℃.Along with outstanding cyclic stability of capacitive performance at 200℃,this work provides a promising class of dielectric materials for robust high-performance all-organic dielectric nanocomposites.

Review on synergistic damage effect of irradiation and corrosion on reactor structural alloys

The synergistic damage effect of irradiation and corrosion of reactor structural materials has been a prominent research focus.This paper provides a comprehensive review of the synergistic effects on the third-and fourth-generation fission nuclear energy structural materials used in pressurized water reactors and molten salt reactors.The competitive mechanisms of multiple influencing factors,such as the irradiation dose,corrosion type,and environmental temperature,are summarized in this paper.Conceptual approaches are proposed to alleviate the synergistic damage caused by irradiation and corrosion,thereby promoting in-depth research in the future and solving this key challenge for the structural materials used in reactors.

Effect of high-energy Ne ions irradiation on mechanical properties difference between Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5)metallic glass and crystalline W

In this paper,high-energy Ne ions were used to irradiate Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) metallic glass(MG)and crystalline W to investigate their difference in mechanical response after irradiation.The results showed that with the irradiation dose increased,the tensile micro-strain increased,nano-hardness increased from 7.11 GPa to 7.90 GPa and 8.62 GPa,Young’s modulus increased,and H3/E2 increased which indicating that the plastic deformability decreased in crystalline W.Under the same irradiation conditions,the Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG still maintained the amorphous structure and became more disordered despite the longer range and stronger displacement damage of Ne ions in Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG than in crystalline W.Unlike the irradiation hardening and embrittlement behavior of crystalline W,Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG showed the gradual decrease in hardness from 6.02 GPa to 5.89 GPa and 5.50 GPa,the decrease in modulus and the increase in plastic deformability with the increasing dose.Possibly,the irradiation softening and toughening phenomenon of Zr_(63.5)Cu_(23)Al_(9)Fe_(4.5) MG could provide new ideas for the design of nuclear materials.

Effect of three-volt moxibustion with helium-neon laser irradiation on quality of care in patients with lumbar radiculopathy spondylosis

BACKGROUND Lumbar radiculopathy spondylosis is a relatively common orthopedic disease with a high incidence rate.It most commonly occurs in the lumbar 4-5 and lumbar 5-sacral 1 vertebrae,which account for approximately 95%of cases.It mostly occurs in people aged 30-50 years old and greatly affects their quality of life.AIM To determine the effect of triple-voltage acupuncture combined with helium-neon laser irradiation on the quality of care and improvement of symptoms in patients with lumbar radiculopathy spondylolisthesis.METHODS In this study,we selected 120 patients with lumbar radiculopathy spondylosis who were treated at our hospital between June 2019 to June 2020.The patients were divided into control and observation groups according to the random number table method,with 60 patients in each group.Patients in the observation group were treated with three-volt moxibustion combined with helium-neon laser irradiation,and those in the control group were treated with lumbar traction.After 1 month of treatment,the lumbar pain scores,lumbar spine motor functions,clinical treatment effects,and nursing satisfaction of the two groups were compared.RESULTS The results showed that acupuncture combined with laser irradiation significantly improved the patients'clinical symptoms,i.e.,reduced their low back pain,significantly lower numerical rating scale pain scores in the observation group than in the control group,and better lumbar spine motility than in the control group,compared to lumbar traction.In addition,they were cared for.The treatment effectiveness rate of the observation group was 95.5%,which was significantly higher than that of the control group(81.67%).Satisfaction with care was higher than 90 points in both groups,but the difference was not statistically significant.CONCLUSION Our study provides a clinical rationale for the future treatment of patients with lumbar spine disease.However,further extensive research is needed for validation.

The Influence of Air Pollution Concentrations on Solar Irradiance Forecasting Using CNN-LSTM-mRMR Feature Extraction

Maintaining a steady power supply requires accurate forecasting of solar irradiance,since clean energy resources do not provide steady power.The existing forecasting studies have examined the limited effects of weather conditions on solar radiation such as temperature and precipitation utilizing convolutional neural network(CNN),but no comprehensive study has been conducted on concentrations of air pollutants along with weather conditions.This paper proposes a hybrid approach based on deep learning,expanding the feature set by adding new air pollution concentrations,and ranking these features to select and reduce their size to improve efficiency.In order to improve the accuracy of feature selection,a maximum-dependency and minimum-redundancy(mRMR)criterion is applied to the constructed feature space to identify and rank the features.The combination of air pollution data with weather conditions data has enabled the prediction of solar irradiance with a higher accuracy.An evaluation of the proposed approach is conducted in Istanbul over 12 months for 43791 discrete times,with the main purpose of analyzing air data,including particular matter(PM10 and PM25),carbon monoxide(CO),nitric oxide(NOX),nitrogen dioxide(NO_(2)),ozone(O₃),sulfur dioxide(SO_(2))using a CNN,a long short-term memory network(LSTM),and MRMR feature extraction.Compared with the benchmark models with root mean square error(RMSE)results of 76.2,60.3,41.3,32.4,there is a significant improvement with the RMSE result of 5.536.This hybrid model presented here offers high prediction accuracy,a wider feature set,and a novel approach based on air concentrations combined with weather conditions for solar irradiance prediction.

The impact of^(60)Co-γirradiation on the chemical constituents of Chuanxiong Rhizoma

Background:In order to clarify the inmpat ofγirradiation on the chemical composition of traditional Chinese medicine,this paper carefully choosed Chuanxiong Rhizoma to carry on a demonstration study.Methods:Through a meticulous assessment,a comprehensive comparison was made between the irradiated and unirradiated Chuanxiong Rhizoma samples.The property characteristics were investigated by colorimeter and electronic nose.The changes in chemical structures and contents was analyzed by fourier infrared spectroscopy,high performance liquid chromatography and fingerprinting.In a quest to uncover the presence of any new radiolysis products,cutting-edge techniques like ultra performance liquid chromatography-quadrupole-time of flight-mass spectrometry and gas chromatography-mass spectrometry were employed.Moreover,the difference of antioxidant activity were investigated.Results:The irradiation doses within 12 kGy had no significant effects on the content of the main chemical components,characteristics and in vitro antioxidant activity of Chuanxiong Rhizoma,while changes in some functional groups and degradation of some volatile oil components containing olefins need further study.Conclusion:This study indicates that^(60)Co-γirradiation is a stable method for sterilization of Chuanxiong Rhizoma.It’s also provide a reference for the establishment of irradiation standards for Chuanxiong Rhizoma and other aromatic medicinal plants.

Observation of therapeutic effect of lamp irradiation combined with purple gromwell oil gauze on alleviating intestinal colic in patients

BACKGROUND Intestinal colic is a common complication in patients who have undergone radical surgery for colorectal cancer.Traditional Chinese medicine has advantages,including safety and stability,for the treatment of intestinal colic.Lamp irra-diation for abdominal ironing has been applied in the treatment of many gas-trointestinal diseases.Purple gromwell oil has the effects of clearing heat,cooling blood,reducing swelling,and relieving pain.RESULTS The general effective rate in the observation group was 95.00%,which was significantly higher than that in the control group(86.67%,P<0.05).Before treatment,there was no significant difference in the duration of symptoms between the groups(P>0.05).After 1,2,3,and 4 d of treatment,the duration of symptoms in both groups were decreased,and the duration in the observation group was significantly lower than that in the control group(96.54±9.57 vs 110.45±11.23,87.26±12.07 vs 104.44±11.68,80.45±16.21 vs 99.44±14.95,73.18±15.58 vs 92.17±14.20;P<0.05).After 1,3,5,and 7 d of treatment,the NRS scores in both groups were decreased,and the NRS scores in the observation group were significantly lower than those in the control group(3.56±0.41 vs 4.04±0.58,3.07±0.67 vs 3.74±1.02,2.52±0.76 vs 3.43±0.85,2.03±0.58 vs 3.03±0.82;P<0.05).There was no significant difference in the rate of adverse reaction occurrence between the groups(P>0.05).CONCLUSION The use of lamp irradiation combined with purple gromwell oil gauze in patients with intestinal colic after radical surgery for colorectal cancer can reduce symptom duration,alleviate intestinal colic,and improve treatment efficacy,and this approach is safe.It is worth promoting the use of this treatment in clinical practice.

UV-LED油墨在软包装凹版印刷中的应用研究

通过制备一种UV-LED环保油墨和适配的UV-LED固化光源,并对凹版印刷机进行改进设计,构建一套采用UV-LED冷光源固化色墨的凹版印刷系统,进行软包装材料的印刷试验。在印速200 m/min、UV-LED波长385 nm、单个色组最低光功率6 kW等工艺条件下,UV-LED油墨在PET(聚对苯二甲酸乙二酯)、OPP(邻苯基苯酚)、CPP(流延聚丙烯)、PE(聚乙烯)等基材上只需0.1 s即可固化,印刷质量达到批量生产要求。无溶剂软包装凹版印刷工艺先进,环保节能,可以取代传统溶剂型印刷,从源头上解决软包装凹印企业的VOCs治理难题,促进产业转型升级。

基于热管风冷的大功率UV-LED固化灯散热研究

应用于油墨固化领域的UV固化灯常采用密集阵列排布的UV-LED模组作为高辐射高能量的光源,而高能量的UV固化灯对其散热器的结构设计提出很高的要求。本文结合数值模拟与实验,提出一种基于强制风冷的热管式散热器,通过理论计算证明该散热器结构的可行性,研究了300~1500 W功率下基板温度变化情况,对比分析了不同抽风量与散热片数量下热源基板温度变化情况,得出抽风量7 m^3/min、散热片数量为35片时散热效果最佳。实验所测结果与仿真结果误差为4%,证实了仿真结果的准确性,对大功率UV固化灯风冷散热器设计具有参考价值。

UV-LED水性网印油墨的制备与性能研究

采用单因素分析法,分析了UV-LED水性网印油墨材料组分和用量对油墨性能的影响,并通过正交试验分析,最终得出UV-LED水性网印油墨的配方为:预聚物为80%、光引发剂TPO为5.5%、染料为9%、光活化剂为3%、消泡剂为0.9%、表面活性剂为0.8%以及流平剂为0.8%。研究结果表明:制得的UV-LED水性网印油墨固化速率高,黏度符合标准,固含量和附着力优异,各项性能指标能满足网印的要求。