Spatiotemporal mapping of(ultra‐)mafic magmatic mine areas:Implications of economic and political realities in China

The spatiotemporal extension/expansion of mine areas is affected by multiple factors.So far,very little has been done to examine the interaction between mine areas and political or economic realities.The(ultra‐)mafic magmatic mines in China played a specific role in supporting national development and providing an ideal research subject for monitoring their interrelationship.In this study,remote sensing and mining‐related GIS data were used to identify and analyze 1233(ultra‐)mafic magmatic mine area polygons in China,which covered approximately 322.96 km2 of land and included a V–Ti–Fe mine,a copper–nickel mine,a chromite mine,an asbestos mine,and a diamond mine.It was found that(1)the areal expansion of mines is significantly related to the mine types,perimeter,topography,and population density.(2)The mine area variation also reflects market and policy realities.The temporal expansion of the mine area from 2010 to 2020 followed an S‐shaped pattern(with the turning point occurring in 2014),closely related to iron overcapacity and tightened mining policies.(3)The complexity(D)of the mine area may reflect mine design and excavation practices.To be specific,lower D indicates early‐stage or artisanal/small‐scale mining,whereas higher D represents large‐scale mining.This study demonstrates that the detailed mapping of mine land can serve as an indicator to implement miningrelated market and policy changes.The(ultra‐)mafic mines area data set can be accessed at https://zenodo.org/record/7636616#.Y-p0uXaZOa0.

Xpert MTB/RIF Ultra对结核性脑膜炎的早期诊断价值

目的:评价Xpert MTB/RIF Ultra(Ultra)对结核性脑膜炎(TBM)的早期诊断价值。方法:对79例患者的临床资料进行分析,用Ultra、Xpert MTB/RIF(Xpert)、宏基因测序(mNGS)和分枝杆菌培养(MGIT)检测脑脊液(CSF)中的结核分枝杆菌。在临床诊断的基础上,分析各方法的检测性能和利福平药物敏感性。结果:Ultra的敏感度(56.4%)、曲线下面积(AUC值)和Kappa值(0.521)均高于MGIT(20%、0.600、0.236)、Xpert(40%、0.700、0.236)和mNGS(32.7%、0.664、0.352)。在31例Ultra阳性病例中,24例对利福平敏感,7例耐药性不确定。结论:与其他方法相比,Ultra检测脑脊液中结核分枝杆菌具有较高的敏感性。因此,Ultra可用于TBM的早期诊断。

Xpert MTB/RIF Ultra在儿童结核诊断中的应用价值

目的:探讨Xpert MTB/RIF Ultra在儿童结核诊断中的应用价值。方法:选取2010年1月—2022年12月山东省公共卫生临床中心收治的150例患儿作为研究对象。根据临床综合诊断确诊结果将结核病感染患儿纳入试验组(n=100),将非结核病感染患儿纳入对照组(n=50)。计算不同标本类型的敏感度、特异度、阴性预测值、阳性预测值和准确度,评价Xpert MTB/RIF Ultra检出利福平(RIF)耐药性的效能。结果:Xpert MTB/RIF Ultra的检测所有标本总敏感度为77.00%,特异度为96.00%;合并肺内标本敏感度为92.85%,特异度为96.29%,其中肺内标本中肺泡灌洗液敏感度最高为100.00%;合并肺外标本敏感度为77.55%,特异度为95.65%,其中肺外标本中淋巴结敏感度最高为100.00%。结论:不同标本类型中Xpert MTB/RIF Ultra对儿童结核的检出率差异较大,在诊断肺内结核标本时,检测肺泡灌洗液标本价值最高,在诊断肺外结核标本时,检测淋巴结标本价值最高。

Experimental Investigation on Cooling/Heating Characteristics of Ultra-Thin Micro Heat Pipe for Electric Vehicle Battery Thermal Management

Due to the heat pipes’ transient conduction,phase change and fluid dynamics during cooling/heating with high frequency charging/discharging of batteries,it is crucial to investigate in depth the experimental dynamic thermal characteristics in such complex heat transfer processes for more accurate thermal analysis and design of a BTMS. In this paper,the use of ultra?thin micro heat pipe(UMHP) for thermal management of a lithium?ion battery pack in EVs is explored by experiments to reveal the cooling/heating characteristics of the UMHP pack. The cooling performance is evaluated under di erent constant discharging and transient heat inputs conditions. And the heating e ciency is assessed under several sub?zero temperatures through heating films with/without UMHPs. Results show that the pro?posed UMHP BTMS with forced convection can keep the maximum temperature of the pack below 40 °C under 1 ~ 3 C discharging,and e ectively reduced the instant temperature increases and minimize the temperature fluctuation of the pack during transient federal urban driving schedule(FUDS) road conditions. Experimental data also indicate that heating films stuck on the fins of UMHPs brought about adequate high heating e ciency comparing with that stuck on the surface of cells under the same heating power,but has more convenient maintenance and less cost for the BTMS. The experimental dynamic temperature characteristics of UMHP which is found to be a high?e cient and low?energy consumption cooling/heating method for BTMSs,can be performed to guide thermal analysis and optimiza?tion of heat pipe BTMSs.

Anisotropy of Trabecular Bone from Ultra-Distal Radius Digital X-Ray Imaging: Effects on Bone Mineral Density and Age

Background: When applied to trabecular bone X-ray images, the anisotropic properties of trabeculae located at ultra-distal radius were investigated by using the trabecular bone scores (TBS) calculated along directions parallel and perpendicular to the forearm. Methodology: Data from more than two hundred subjects were studied retrospectively. A DXA (GE Lunar Prodigy) scan of the forearm was performed on each subject to measure the bone mineral density (BMD) value at the location of ultra-distal radius, and an X-ray digital image of the same forearm was taken on the same day. The values of trabecular bone score along the direction perpendicular to the forearm, TBSx, and along the direction parallel to the forearm, TBSy, were calculated respectively. The statistics of TBSx and TBSy were calculated, and the anisotropy of the trabecular bone, which was defined as the ratio of TBSy to TBSx and changed with subjects’ BMD and age, was reported and analyzed. Results: The results show that the correlation coefficient between TBSx and TBSy was 0.72 (p BMD and age was reported. The results showed that decreased trabecular bone anisotropy was associated with deceased BMD and increased age in the subject group. Conclusions: This study shows that decreased trabecular bone anisotropy was associated with decreased BMD and increased age.

First-principles study and electronic structures of Mn-doped ultrathin ZnO nanofilms

The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida（RKKY） interaction.

Research on the Influence of Cutting Condition on the Surface Microstruct ure of Ultra-thin Wall Parts in Ultrasonic Vibration Cutting

In many fields of high-tech industry the ultra-t hi n wall parts are employed. In this paper the experiments were carried out to dis cuss the surface microstructure of the camera’s guided drawtube by applying ult rasonic vibration cutting device to the traditional lathe. The influence rule of the cutting condition on the surface roughness was put forward, which was drawn by comparing the ultrasonic cutting with the common cutting by use of the cemen ted carbide tool and the polycrystalline diamond (PCD) tool. The test results sh owed that the ultrasonic cutting performs better than the common cutting in the same condition. According to the test results analyzing, the surface characteriz ation is influenced clearly by the rigidity of the acoustic system and the machi ne tool, as well the setting height of the tool tip. Otherwise, the dense regula r low frequency vibration ripples will be scraped on the machined surface. When the tool tip is set higher than the rotating center of the work piece by three t imes of the amplitude of ultrasonic vibration, the vibration ripples behave alig ht; they turn light and shade alternatively when the tool tip is lower than the rotating center of the work piece by three times of the amplitude of ultrasonic vibration. According to the test result analyzing, the following conclusions are put forward: 1) The surface roughness in ultrasonic cutting is better than that in common cutting. Under a one third critical cutting velocity, the value of th e surface roughness in ultrasonic cutting rise slightly along with the cutting v elocity, while in common cutting it decreases contrast to the cutting velocity; the curves of the surface roughness in ultrasonic cutting and common cutting see m to be alike, both increase along with the feed rate and the cutting depth, but the value in ultrasonic cutting is smaller in the same condition.2) The influen ce of the coolant on the surface roughness cannot be ignored. The kerosene can b e employed to improve the surface roughness in ultrasonic machining.3) In ultras onic cutting process of aluminum alloy ultra-thin wall work piece, the PCD tool performs better than the cemented carbide tools.4) The vibration ripples result from the not enough rigidity of the acoustic system and the improper setting he ight of the tool tip. The departure of the tool tip from the rotating center of the work piece to some extent causes the vibration ripples on the machined surfa ce.

Ultra-Thin Body SOI MOSFET交流特性分析和结构优化

针对沟道长度为 5 0nm的UTBSOI器件进行了交流模拟工作 ,利用器件主要的性能参数 ,详细分析了UTB结构的交流特性 .通过分析UTBSOI器件的硅膜厚度、侧墙宽度等结构参数对器件交流特性的影响 ,对器件结构进行了优化 .最终针对UTBSOIMOSFET结构提出了一种缓解速度和功耗特性优化之间矛盾的方法 ,从而实现了结构参数的优化选取 。

Analysis on Dynamic Characteristics in Time Domain of Slider with Ultra Thin Spacing

With increasing recording density in computer hard disks,the flying height of the magnetic head becomes 10 nm or less.The numerical method of the control equations needs to be optimized consistently with the decrease of the flying height.The iterative process is usually divergent with traditional methods which cannot ensure the accuracy of the analysis results and the stability of numerical calculations.Firstly,a new scheme is presented to solve the ultra-thin lubricating control equations in this paper.The equilibrium equation is obtained by taking the Couette flow terms and time term as dominating terms in iterative process.Moreover,the weighting flow factor is introduced for the abrupt change of film thickness in order to reduce calculated deviation.Secondly,the rules for variation of flying pose of the magnetic head with time are obtained by the time domain analysis.The results show that the magnetic head can recover to the equilibrium position after being slightly influenced by outside disturbance.And the dynamic lubrication properties of the head suffer heavily from the vibrations in the height direction and fluctuation in the pitch direction.Finally,the analysis of the sine roughness-passing capacity of the head indicates that the head can surpass small sine waves and the equilibrium position can be retrieved after a period of decaying oscillation.The proposed research ensures the accuracy and stability of the numerical calculation of the control equations,and the dynamic characteristics and flying stability of a magnetic head is studied systematically.It can also be the theoretical basis for the analysis of the flight characteristics of the slider.

Large energy-loss straggling of swift heavy ions in ultra-thin active silicon layers

Monte Carlo simulations reveal considerable straggling of energy loss by the same ions with the same energy in fully-depleted silicon-on-insulator （FDSOI） devices with ultra-thin sensitive silicon layers down to 2.5 rim. The absolute straggling of deposited energy decreases with decreasing thickness of the active silicon layer. While the relative straggling increases gradually with decreasing thickness of silicon films and exhibits a sharp rise as the thickness of the silicon film descends below a threshold value of 50 nm, with the dispersion of deposited energy ascending above ~10%. Ion species and energy dependence of the energy-loss straggling are also investigated. For a given beam, the dispersion of deposited energy results in large uncertainty on the actual linear energy transfer （LET） of incident ions, and thus single event effect （SEE） responses, which pose great challenges for traditional error rate prediction methods.

New process for production of ultra-thin grain oriented silicon steel

The Hi-B silicon steels were cold rolled by cross shear rolling (CSR) with different mismatch speed ratio(MSR)s and conventional rolling(CR) respectively, followed by primary recrystallization annealing. The effects of MSR and annealing temperature on magnetic properties of ultra-thin grain oriented silicon steel were analyzed. Experimental results show that, with the increase of MSR, the magnetic properties can be remarkably improved. The higher the annealing temperature is, the higher the magnetic induction and the lower the iron loss in ultra-thin silicon steel is.

Research on Influence of Cutting Conditions on Roundness of Ultra-thin Wall Parts in Ultrasonic Vibration Cutting

In the paper, the experimental researches were carr ie d out to discuss the roundness forming rule and the influence of cutting paramet ers on roundness by ultrasonic vibration cutting of the camera’s guiding drawtu be with 47.75 mm diameter and 0.6～1.5 mm wall thickness. The research results s h ow that the roundness error of ultra-thin wall parts in ultrasonic vibration cu tting is only one third of that in common cutting. The relations between the rou ndness error and the cutting parameters behave as: (1) The roundness error in co mmon cutting decreases gradually with the rise of cutting speed, while in ultras onic cutting, the roundness changes not obviously till the cutting speed is up t o a value, which is nearly equal to one third of the critical velocity. Then the roundness of workpiece will begin to increase slowly. (2) The roundness error i ncreases along with the feed rate both in common cutting and ultrasonic cutting. (3) Within the range of cutting depth in experiment, the influence of cutting d epth on the roundness error is more obvious in common cutting than that in ultra sonic vibration cutting. The conclusions are useful in machining such precise ul tra-thin wall parts. According to the tests, the following conclusions can be o btained: 1) Compared with common cutting, ultrasonic cutting can decrease effect ively roundness error of the workpiece. Under the same condition, the roundness error of the ultra-thin wall part in ultrasonic turning is about one third of t hat in common cutting. 2) In common cutting, cutting depth and feed rate have mu ch influence on the roundness and the influence of cutting velocity is little. W hile in ultrasonic cutting, the roundness was influenced heavily only when feed rate is more than 0.1 mm/r and cutting speed is more than 1/3 of the critical ro tation speed, cutting depth has little influence on the roundness in the experim ent. 3) Kerosene-oil is an optimum cutting fluid in machining ultra-thin wall workpiece. 4) To machine the ultra-thin wall precision part, ultrasonic cutting is the perfect method which can decrease the roundness error effectively an d ensure high quality of the surface.

Ultra-thin circularly polarized lens antenna based on single-layered transparent metasurface

Circularly polarized （CP） lens antenna has been applied to numerous wireless communication systems based on its unique advantages such as high antenna gain, low manufacturing cost, especially stable data transmission between the transmitter and the receiver. Unfortunately, current available CP lens antennas mostly suffer from high profile, low aperture efficiency as well as complex design. In this paper, we propose an ultra-thin CP lens antenna based on the designed single- layered Pancharatnam-Berry （PB） transparent metasurface with focusing property. The PB metasurface exhibits a high transmissivity, which ensures a high efficiency of the focusing property. Launched the metasurface with a CP patch antenna at its focal point, a low-profile lens antenna is simulated and measured. The experimental results show that our lens antenna exhibits a series of advantages including high radiation gain of 20.7 dB, aperture efficiency better than 41.3%, and also narrow half power beam width （HPBW） of 13°at about 14GHz. Our finding opens a door to realize ultra-thin transparent metasurface with other functionalities or at other working frequencies.

The conduction mechanism of stress induced leakage current through ultra-thin gate oxide under constant voltage stresses

The conduction mechanism of stress induced leakage current （SILC） through 2nm gate oxide is studied over a gate voltage range between 1.7V and stress voltage under constant voltage stress （CVS）. The simulation results show that the SILC is formed by trap-assisted tunnelling （TAT） process which is dominated by oxide traps induced by high field stresses. Their energy levels obtained by this work are approximately 1.9eV from the oxide conduction band, and the traps are believed to be the oxygen-related donor-like defects induced by high field stresses. The dependence of the trap density on stress time and oxide electric field is also investigated.

Development of a High-PerformanceFlexible Substrate for Flexible Electronics:Joining TAC Films and an Ultra-Thin Glassby Using TEOS-DAC Synthesized by the Sol-Gel Method

A new flexible substrate for flexible electronics has been developed. The developed substrate consists of an ultra thin glass and TAC (triacethyl cellulose) film. An ultra thin glass and TAC film were joined with TEOS-DAC (TEOS: tetraethyl orthosilicate, DAC: diacethy cellulose) adhesive resin synthesized by sol-gel method by means of thermo-compression bonding. This substrate has high transparency in visible-light region (90%), high flexibility (torsion strength and bending strength) and high gas barrier characteristics due to an ultra thin glass. The newly-developed substrate is superior to the substrates fabricated with commercially available adhesive resin in the same way in characteristics of heat resistance, transparency and flexibility.

A Study on the Effect of Low Calcium Ultra-fine Fly Ash as a Partial Sustainable Supplementary Material to Cement in Self-compacting Concrete

The aim and scope of the present study were to determine the efficacy of UFFA in evaluating the workability,static and dynamic stabilization properties,retention period,and slump loss of SCC systems in their fresh state,as well as their compressive strength at various ages.Microstructure(SEM and XRD)of blended SCC systems were studied.Also,the thermogravimetry behavior of blended SCC specimens were researched.According to the evaluated results,incorporating up to 20%UFFA into fresh concrete improved its performance due to its engineered fine particle size and spherical geometry,both of which contribute to the enhancement of characteristics.Blends of 25%and 30%of UFFA show effect on the water-binder ratio and chemical enhancer dosage,resulting in a loss of homogeneity in fresh SCC systems.The reduced particle size,increased amorphous content,and increased surface area all contribute to the pozzolanic reactivity of the early and later ages,resulting in denser packing and thus an increase in compressive strength.The experimental results indicate that UFFA enhances the properties of SCC in both its fresh and hardened states,which can be attributed to the particles’fineness and their relative effect on SCC.

Xpert MTB/RIF Ultra在快速检测结核分枝杆菌和利福平耐药中的应用

目的探讨Xpert MTB/RIF Ultra在快速检测结核分枝杆菌和利福平耐药中的应用价值。方法收集2019年12月至2020年5月就诊于福州肺科医院的447例疑似肺结核患者的痰标本,分别进行MGIT960液体培养及药敏、Xpert MTB/RIF(Xpert)和Xpert Ultra检测,将检出MTB的菌株和痰液进行rpoB基因Sanger测序。以临床诊断结果为参照,比较MGIT960液体培养、Xpert、Xpert Ultra检测MTB的敏感度和特异度;分别以液体药敏和测序结果为金标准,评价Xpert Ultra检测MTB利福平耐药性的效能。结果以临床确诊为参照,Xpert Ultra敏感度高于液体培养和Xpert,差异有统计学意义(χ^(2)=28.97、164.86,P均<0.05),特异度与液体培养和Xpert比较差异无统计学意义(P均>0.05)。分别以利福平液体药敏表型结果和rpoB基因测序结果为金标准,Xpert Ultra的敏感度为88.89%和93.75%。同时经测序分析,35例利福平耐药样本中,rpoB的531位点突变最为常见,占48.57%。结论Xpert Ultra能快速检测痰液中的MTB及其利福平耐药性,对肺结核早期诊疗有良好的临床应用价值,适合在各级实验室推广。

Tradeoff between speed and static power dissipation of ultra-thin body SOI MOSFETs

The speed performance and static power dissipation of the ultra-thin-body （UTB） MOSFETs have been comprehensively investigated, with both DC and AC behaviours considered. Source/drain extension width （Lsp） and silicon film thickness （tsi） are two independent parameters that influence the speed and static power dissipation of UTB siliconon-insulator （SOI） MOSFETs respectively, which can result in great design flexibility. Based on the different effects of physical and geometric parameters on device characteristics, a method to alleviate the contradiction between power dissipated and speed of UTB SOI MOSFETs is proposed. The optimal design regions of tsi and Lsp for low operating power and high performance logic applications are given, which may shed light on the design of UTB SOI MOSFETs.

COVALENTLY ATTACHED MULTILAYER ULTRA-THIN FILMS FROM DIAZORESIN AND CALIXARENES

A kind of photosensitive ultra-thin film was fabricated from diazoresin (DR) and various calixarenes by using theself-assembly technique. Under UV irradiation both the ionic- and hydrogen bonds between the layers of the film will convert into covalent bonds. As a result, the stability of the film toward polar solvents increases dramatically.

Low voltage substrate current： a monitor for interface states generation in ultra-thin oxide n-MOSFETs under constant voltage stresses

The low voltage substrate current （Ib） has been studied based on generation kinetics and used as a monitor of interface states （Nit） generation for ultra-thin oxide n-MOSFETs under constant voltage stress. It is found that the low voltage Ib is formed by electrons tunnelling through interface states, and the variations of Ib（△Ib） are proportional to variations of Nit （△Nit）. The Nit energy distributions were determined by differentiating Nit（Vg）. The results have been compared with that measured by using gate diode technique.