Residual stress is an important factor for evaluating the deformation and failure of engineering materials. Diffraction-based measurement assumes that the full measured lattice strain tensor contributes to residual st...Residual stress is an important factor for evaluating the deformation and failure of engineering materials. Diffraction-based measurement assumes that the full measured lattice strain tensor contributes to residual stress according to Hookers Law. The present work focuses on the lattice strain determination of individual grains in a dual-phase stainless steel （DPSS） by means of differential-aperture X-ray micro-diffraction （DAXM）. The results show that the residual stress only takes part of the responsibility of the total measured lattice strain. In fact, the compositional variation inside the material was found to cause greater strain gradient in both ferrite （c~） and austenite （~） phases in DPSS. Therefore, quantification of compositional and residual stress effects on lattice strain was conducted in order to evaluate the true residual stress inside engineering materials.展开更多
采用熔化极活性气体保护焊(metal active gas arc welding,MAG焊)、等离子弧焊(plasma arc welding,PAW)和高频感应焊接方法获得铁素体+马氏体双相组织不锈钢00Cr12Ni的焊接接头,对其组织区域特征和力学性能进行了研究.典型的焊接接头...采用熔化极活性气体保护焊(metal active gas arc welding,MAG焊)、等离子弧焊(plasma arc welding,PAW)和高频感应焊接方法获得铁素体+马氏体双相组织不锈钢00Cr12Ni的焊接接头,对其组织区域特征和力学性能进行了研究.典型的焊接接头热影响区(heat affected zone,HAZ)可分为晶粒粗大,铁素体为优势相的高温热影响区(high temperature heat affected zone,HTHAZ)和晶粒细小,马氏体为优势相的低温热影响区(low temperature heat affected zone,LTHAZ).通过测量实际焊接热循环曲线的方法确定了HTHAZ及LTHAZ的温度范围,并采用热模拟研究HAZ不同区域的力学性能.结果表明,HTHAZ的热循环峰值范围为1200℃至熔点,晶粒粗大呈现为脆性;LTHAZ热循环峰值范围为800~1200℃,室温组织为非平衡低碳板条马氏体,韧性较好,但低于0℃时呈脆性.MAG焊接头由于奥氏体焊缝为钟罩形,HAZ冲击试验时断面包括奥氏体焊缝,因此冲击性能较好;PAW接头在1000℃奥氏体快冷可获得细晶粒马氏体韧性提高;高频感应焊接接头中无HTHAZ,但焊接过程中的加工硬化导致室温呈脆性,通过去应力退火后韧性恢复.展开更多
文章概述了克拉2气田中央处理厂U N S S32205双相不锈钢管道系统的基本情况。介绍了U N S S32205双相不锈钢的化学性能和物理性能,在管道施工过程中的特点和难点,相关的焊接工艺试验和焊接工艺评定以及施焊过程中的技术措施;提出了在实...文章概述了克拉2气田中央处理厂U N S S32205双相不锈钢管道系统的基本情况。介绍了U N S S32205双相不锈钢的化学性能和物理性能,在管道施工过程中的特点和难点,相关的焊接工艺试验和焊接工艺评定以及施焊过程中的技术措施;提出了在实际操作中的注意事项。实践证明,在U N S S32205双相不锈钢管道系统的焊接过程中,严格控制焊接管道内的氧气含量和焊接线能量是保证焊接质量的关键环节。展开更多
基金financial supported by the National Science Foundation of China(No.51231002)supported by the U.S.Department of Energy,Office of Science,Office of Basic Energy Sciences,under Contract No.DE-AC02-06CH11357
文摘Residual stress is an important factor for evaluating the deformation and failure of engineering materials. Diffraction-based measurement assumes that the full measured lattice strain tensor contributes to residual stress according to Hookers Law. The present work focuses on the lattice strain determination of individual grains in a dual-phase stainless steel （DPSS） by means of differential-aperture X-ray micro-diffraction （DAXM）. The results show that the residual stress only takes part of the responsibility of the total measured lattice strain. In fact, the compositional variation inside the material was found to cause greater strain gradient in both ferrite （c~） and austenite （~） phases in DPSS. Therefore, quantification of compositional and residual stress effects on lattice strain was conducted in order to evaluate the true residual stress inside engineering materials.
文摘采用熔化极活性气体保护焊(metal active gas arc welding,MAG焊)、等离子弧焊(plasma arc welding,PAW)和高频感应焊接方法获得铁素体+马氏体双相组织不锈钢00Cr12Ni的焊接接头,对其组织区域特征和力学性能进行了研究.典型的焊接接头热影响区(heat affected zone,HAZ)可分为晶粒粗大,铁素体为优势相的高温热影响区(high temperature heat affected zone,HTHAZ)和晶粒细小,马氏体为优势相的低温热影响区(low temperature heat affected zone,LTHAZ).通过测量实际焊接热循环曲线的方法确定了HTHAZ及LTHAZ的温度范围,并采用热模拟研究HAZ不同区域的力学性能.结果表明,HTHAZ的热循环峰值范围为1200℃至熔点,晶粒粗大呈现为脆性;LTHAZ热循环峰值范围为800~1200℃,室温组织为非平衡低碳板条马氏体,韧性较好,但低于0℃时呈脆性.MAG焊接头由于奥氏体焊缝为钟罩形,HAZ冲击试验时断面包括奥氏体焊缝,因此冲击性能较好;PAW接头在1000℃奥氏体快冷可获得细晶粒马氏体韧性提高;高频感应焊接接头中无HTHAZ,但焊接过程中的加工硬化导致室温呈脆性,通过去应力退火后韧性恢复.
文摘文章概述了克拉2气田中央处理厂U N S S32205双相不锈钢管道系统的基本情况。介绍了U N S S32205双相不锈钢的化学性能和物理性能,在管道施工过程中的特点和难点,相关的焊接工艺试验和焊接工艺评定以及施焊过程中的技术措施;提出了在实际操作中的注意事项。实践证明,在U N S S32205双相不锈钢管道系统的焊接过程中,严格控制焊接管道内的氧气含量和焊接线能量是保证焊接质量的关键环节。
