Ensuring the homogeneous and excellent mechanical properties of 2.25Cr-1Mo-0.25V ultra-thick steel plate is the key to the production of hydrogenation reactor equipment.Thus,it is required to understand the heterogene...Ensuring the homogeneous and excellent mechanical properties of 2.25Cr-1Mo-0.25V ultra-thick steel plate is the key to the production of hydrogenation reactor equipment.Thus,it is required to understand the heterogeneity of microstructures and properties of ultra-thick plate after heat treatment.In this work,the effect of post-weld heat treatment(PWHT)on the strength,plasticity,toughness and microstructures of the 193-mm-thick steel plate was investigated,and the formation mechanism of heterogeneity was elucidated.The PWHT decreased the room-and high-temperature yield strength(YS)and ultimate tensile strength(UTS)of the steel plate after normalizing and tempering(NT),while the room-and high-temperature YS and UTS decreased from the surface to the center of 193-mm-thick steel plate.It was attributed to the enhanced decomposition of martensite-austenite(M-A)constituents and coarsening of grains and precipitated carbides.展开更多
In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-si...In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-side FSW butt joint with more attention paid to the local characteristic zones.It was shown that a phenomenon of microstructural inhomogeneity existed in the nugget zone(NZ)through the thickness direction.The grain size presented an obvious gradient distribution from the top to the bottom for each single-pass weld,and the microhardness values decreased from both surfaces to the middle of the NZ.The lowest hardness zone(LHZ)exhibited a"hyperbolical"-shaped distribution extending to the middle of the NZ.Similar tensile properties were obtained in the three sliced specimens of the FSW joint,and the joint coefficient reached about 70%which achieved the same level as the conventional FSW Al alloy joints.Finite element modeling proved that the"hyperbolical"-shaped heat affected zone(HAZ)was beneficial to resisting the strain concentration in the middle layer specimen which helped to increase the tensile strength.Based on the analysis of the hardness contour map,tensile property and microstructural evolution of the joints,an Isothermal Softening Layer(ISL)model was proposed and established,which may have a helpful guidance for the optimization on the FSW of ultra-thick Al alloy plates.展开更多
INCREASING evidence has demonstrated that the locally controlled proteolytic activity generatedby coordinated expression of tPA and PAI-1 in different tissues may play an important role inmany reproductive events. The...INCREASING evidence has demonstrated that the locally controlled proteolytic activity generatedby coordinated expression of tPA and PAI-1 in different tissues may play an important role inmany reproductive events. These are largely related to fibrinolytic activity. They include folli-cle rupture, luteolysis, spermatogenesis and trophoblast implantation. Parturition, whichis a complex process, may also be associated with tissue destruction. Detachment of placentaldecidua and partial breakdown of fetal membranes are possible examples. It has been展开更多
基金supported by the National Natural Science Foundation of China-Outstanding Young Scholars(No.52325407)the National Natural Science Foundation of China(No.51904187)the Open Project of State Key Laboratory of Advanced Special Steel and Shanghai Key Laboratory of Advanced Ferrometallurgy,Shanghai University(SKLASS 2022-06).
文摘Ensuring the homogeneous and excellent mechanical properties of 2.25Cr-1Mo-0.25V ultra-thick steel plate is the key to the production of hydrogenation reactor equipment.Thus,it is required to understand the heterogeneity of microstructures and properties of ultra-thick plate after heat treatment.In this work,the effect of post-weld heat treatment(PWHT)on the strength,plasticity,toughness and microstructures of the 193-mm-thick steel plate was investigated,and the formation mechanism of heterogeneity was elucidated.The PWHT decreased the room-and high-temperature yield strength(YS)and ultimate tensile strength(UTS)of the steel plate after normalizing and tempering(NT),while the room-and high-temperature YS and UTS decreased from the surface to the center of 193-mm-thick steel plate.It was attributed to the enhanced decomposition of martensite-austenite(M-A)constituents and coarsening of grains and precipitated carbides.
基金supported by the Youth Innovation Promotion Association of the Chinese Academy of Sciences(2017236)National Natural Science Foundation of China under grant No.U1760201.
文摘In the present work,80 mm thick 6082Al alloy plates were successfully double-side welded by friction stir welding(FSW).The relationship between the microstructures and mechanical properties was built for the double-side FSW butt joint with more attention paid to the local characteristic zones.It was shown that a phenomenon of microstructural inhomogeneity existed in the nugget zone(NZ)through the thickness direction.The grain size presented an obvious gradient distribution from the top to the bottom for each single-pass weld,and the microhardness values decreased from both surfaces to the middle of the NZ.The lowest hardness zone(LHZ)exhibited a"hyperbolical"-shaped distribution extending to the middle of the NZ.Similar tensile properties were obtained in the three sliced specimens of the FSW joint,and the joint coefficient reached about 70%which achieved the same level as the conventional FSW Al alloy joints.Finite element modeling proved that the"hyperbolical"-shaped heat affected zone(HAZ)was beneficial to resisting the strain concentration in the middle layer specimen which helped to increase the tensile strength.Based on the analysis of the hardness contour map,tensile property and microstructural evolution of the joints,an Isothermal Softening Layer(ISL)model was proposed and established,which may have a helpful guidance for the optimization on the FSW of ultra-thick Al alloy plates.
文摘INCREASING evidence has demonstrated that the locally controlled proteolytic activity generatedby coordinated expression of tPA and PAI-1 in different tissues may play an important role inmany reproductive events. These are largely related to fibrinolytic activity. They include folli-cle rupture, luteolysis, spermatogenesis and trophoblast implantation. Parturition, whichis a complex process, may also be associated with tissue destruction. Detachment of placentaldecidua and partial breakdown of fetal membranes are possible examples. It has been
