High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting sp...High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting speed,vc=190-300 m/min;cutting depth of axial,ap=5,7 mm),saw-tooth chips were produced in these experiments.During the macro and micro analysis of the Ti-6Al-4V chips,an optical microscope and a scanning electron microscope(SEM)were used to study the microstructure and the morphology of the chips,and the X-ray photoelectron spectroscopy(XPS)was employed for chemical analysis.Comparisons were made to study the influence of different cutting media(nitrogen-oil-mist,air-oil-mist and dry cutting condition)on chip formation.Results indicate that cutting media have significant effects on chip formation.Nitrogen-oil-mist is more suitable for improving the contact condition at chip-tool interface and increasing the tool life in high speed milling of Ti-6Al-4V alloy than air-oil-mist and dry cutting.展开更多
High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due...High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.展开更多
The progressive cutting based on auxiliary paths is an effective machining method for the material accumulating region inside the mould pocket. But the method is commonly based on the radial depth of cut as the contro...The progressive cutting based on auxiliary paths is an effective machining method for the material accumulating region inside the mould pocket. But the method is commonly based on the radial depth of cut as the control parameter, further more there is no more appropriate adjustment and control approach. The end-users often fall to set the parameter correctly, which leads to excessive tool load in the process of actual machining. In order to make more reasonable control of the machining load and toolpath, an engagement angle modeling method for multiplecircle continuous machining is presented. The distribution mode of multiple circles, dynamic changing process of engagement angle, extreme and average value of engage- ment angle are carefully considered. Based on the engagement angle model, numerous application techniques for mould pocket machining are presented, involving the calculation of the milling force in multiple-circle continuous machining, and rough and finish machining path planning and load control for the material accumulating region inside the pocket, and other aspects. Simulation and actual machining experiments show that the engagement angle modeling method for multiple-circle continuous machining is correct and reliable, and the related numerous application techniques for pocket machining are feasible and effective. The proposed research contributes to the analysis and control tool load effectively and tool-path planning reasonably for the material accumulating region inside the mould pocket.展开更多
The research and application on small denture machining equipment are great breakthrough for modern dental restoration technology. In this paper, a small denture machining equipment made of two spindles with four-axis...The research and application on small denture machining equipment are great breakthrough for modern dental restoration technology. In this paper, a small denture machining equipment made of two spindles with four-axis was designed based on machining characteristics and functional analysis. Position accuracy and re-position accuracy were measured by accuracy instrument. In order to test its machining capacity, some typical microstcucture parts, such as straight channel, hemispherical surface, and molars coronal, were selected for high speed milling. It was obtained that the denture machining equipment met the machining requirements with high quality and efficiency, according to the acquisition and analysis of form and position errors, surface roughness, and 3-D profile.展开更多
A compound process that integrates end electrical discharge (ED) milling and mechanical grinding to machine silicon carbide (SiC) ceramics is developed in this paper. The process employs a turntable with several unifo...A compound process that integrates end electrical discharge (ED) milling and mechanical grinding to machine silicon carbide (SiC) ceramics is developed in this paper. The process employs a turntable with several uniformly-distributed cylindrical copper electrodes and abrasive sticks as the tool, and uses a water-based emulsion as the machining fluid. End electrical discharge milling and mechanical grinding happen alternately and are mutually beneficial, so the process is able to effectively machine a large surface area on SiC ceramic with a good surface quality. The machining principle and characteristics of the technique are introduced. The effects of polarity, pulse duration, pulse interval, open-circuit voltage, discharge current, diamond grit size, emulsion concentration, emulsion flux, milling depth and tool stick number on performance parameters such as the material removal rate, tool wear ratio, and surface roughness have been investigated. In addition, the microstructure of the machined surface under different machining conditions is examined with a scanning electron microscope and an energy dispersive spectrometer. The SiC ceramic was mainly removed by end ED milling during the initial rough machining mode, whereas it is mainly removed by mechanical grinding during the later finer machining mode; moreover, the tool material can transfer to the workpiece surface during the compound process.展开更多
基金the National Natural Science Foundation of China (Grant No. 50175051)
文摘High speed milling experiments using nitrogen-oil-mist as the cutting medium were carried out to investigate the characteristics of chip formation for Ti-6Al-4V alloy.Within the range of conditions employed(cutting speed,vc=190-300 m/min;cutting depth of axial,ap=5,7 mm),saw-tooth chips were produced in these experiments.During the macro and micro analysis of the Ti-6Al-4V chips,an optical microscope and a scanning electron microscope(SEM)were used to study the microstructure and the morphology of the chips,and the X-ray photoelectron spectroscopy(XPS)was employed for chemical analysis.Comparisons were made to study the influence of different cutting media(nitrogen-oil-mist,air-oil-mist and dry cutting condition)on chip formation.Results indicate that cutting media have significant effects on chip formation.Nitrogen-oil-mist is more suitable for improving the contact condition at chip-tool interface and increasing the tool life in high speed milling of Ti-6Al-4V alloy than air-oil-mist and dry cutting.
文摘High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.
基金Supported by National Natural Science Foundation-Guangdong Collaborative Fund Key Program(Grant No.U12012081)
文摘The progressive cutting based on auxiliary paths is an effective machining method for the material accumulating region inside the mould pocket. But the method is commonly based on the radial depth of cut as the control parameter, further more there is no more appropriate adjustment and control approach. The end-users often fall to set the parameter correctly, which leads to excessive tool load in the process of actual machining. In order to make more reasonable control of the machining load and toolpath, an engagement angle modeling method for multiplecircle continuous machining is presented. The distribution mode of multiple circles, dynamic changing process of engagement angle, extreme and average value of engage- ment angle are carefully considered. Based on the engagement angle model, numerous application techniques for mould pocket machining are presented, involving the calculation of the milling force in multiple-circle continuous machining, and rough and finish machining path planning and load control for the material accumulating region inside the pocket, and other aspects. Simulation and actual machining experiments show that the engagement angle modeling method for multiple-circle continuous machining is correct and reliable, and the related numerous application techniques for pocket machining are feasible and effective. The proposed research contributes to the analysis and control tool load effectively and tool-path planning reasonably for the material accumulating region inside the mould pocket.
基金National Key Technology R&D Program,China(No.2009BAI81B02)PhD Programs Foundation of Ministry of Education of China(No.20070287055)Anhui Natural Science Foundation,China(No.1308085QE93)
文摘The research and application on small denture machining equipment are great breakthrough for modern dental restoration technology. In this paper, a small denture machining equipment made of two spindles with four-axis was designed based on machining characteristics and functional analysis. Position accuracy and re-position accuracy were measured by accuracy instrument. In order to test its machining capacity, some typical microstcucture parts, such as straight channel, hemispherical surface, and molars coronal, were selected for high speed milling. It was obtained that the denture machining equipment met the machining requirements with high quality and efficiency, according to the acquisition and analysis of form and position errors, surface roughness, and 3-D profile.
基金supported by the National Natural Science Foundation of China(50675225)the Scientific Research Personnel Service Project from the Ministry of Science and Technology of China(2009GJC60047)the Independent Innovation Research Project from China University of Petroleum(11CX04031A)
文摘A compound process that integrates end electrical discharge (ED) milling and mechanical grinding to machine silicon carbide (SiC) ceramics is developed in this paper. The process employs a turntable with several uniformly-distributed cylindrical copper electrodes and abrasive sticks as the tool, and uses a water-based emulsion as the machining fluid. End electrical discharge milling and mechanical grinding happen alternately and are mutually beneficial, so the process is able to effectively machine a large surface area on SiC ceramic with a good surface quality. The machining principle and characteristics of the technique are introduced. The effects of polarity, pulse duration, pulse interval, open-circuit voltage, discharge current, diamond grit size, emulsion concentration, emulsion flux, milling depth and tool stick number on performance parameters such as the material removal rate, tool wear ratio, and surface roughness have been investigated. In addition, the microstructure of the machined surface under different machining conditions is examined with a scanning electron microscope and an energy dispersive spectrometer. The SiC ceramic was mainly removed by end ED milling during the initial rough machining mode, whereas it is mainly removed by mechanical grinding during the later finer machining mode; moreover, the tool material can transfer to the workpiece surface during the compound process.
